Preparation of poly(alkylvinylether)s for nonlinear optical applications

Summary 3,5-Dimethoxy-4-(2-vinyloxyethoxy)-4-nitrostilbene 2 and 3,5-dimethoxy-4-(2-vinyloxyethoxy)-2,4-dinitrostilbene 5 were prepared by the reactions of 2-iodoethyl vinyl ether with 3,5-dimethoxy-4-hydroxy-4-dinitrostilbene 1 and 3,5-dimethoxy-4-hydroxy-2,4-dinitrostilbene 4, respectively. Monomers 2 and 5 were polymerized with cationic initiators to obtain polymers with the NLO-phores 3,5-dimethoxy-4-oxy-4-nitrostilbene and 3,5-dimethoxy-4-oxy-2,4-nitrostilbene in the side chain. The resulting polymer 3 and 6 were soluble in DMSO and DMF. The inherent viscosities of polymers were in the range of 0.28–0.33 dL/g in DMSO. Polymers 3 and 6 showed good thermal stabilities in their TGA thermograms, and the T_g values from DSC thermograms were in the range of 81–87°C.     

Syntheses and properties of polyimides based on bis(p-aminophenoxy)biphenyls

Three biphenyl unit-containing diamines,4,4-bis(p-aminophenoxy)biphenyl (III_a), 2,2-bis(p-aminophenoxy)biphenyl (III_b), and 3,3,5,5-tetramethyl-4,4-bis(p-aminophenoxy)biphenyl (III_c), were prepared by the chlorodisplacement ofp-chloronitrobenzene with 4,4-biphenol (I_a), 2,2-biphenol (I_b), and 3,3,5,5-tetramethyl-4,4-biphenol (I_c), respectively, giving the corresponding bis(nitrophenoxy) compounds II_a-c, followed by catalytic reduction with palladium (Pd) and hydrazine. Three series of polyimidesp-PI,o-PI, and Me-PI were prepared from diamines III_a-c and aromatic tetracarboxylic dianhydrides via a two-stage procedure that included ring-opening polyaddition to give poly(amic acid)s followed by thermal cyclodehydration to polyimides. The resultant three series of poly(amic acid)s had inherent viscosities of 1.09–2.83, 0.78–1.93, and 1.55–3.09 dL/g, respectively. Almost all the poly(amic acid)s could be solution-cast and thermally converted into transparent, flexible, and tough polyimide films. All the polyimides were characterized by solubility, tensile test, wide-angle X-ray scattering measurements, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Effects of the structures of aromatic diamines and dianhydrides on the properties of polyimides were investigated.     

Chemical modification of copoly(methylsilylene/1,4-phenylene) by Pt-catalyzed hydrosilation reactions with functionally substituted alkenes

Copoly(methyl-3-biphenoxypropylsilylene 1,4-phenylene), copoly(methyl-3-cyanopropylsilylene 1,4-phenylene), copoly(methyl-3-ethoxypropylsilylene 1,4-phenylene), copoly(methyl-3-phenoxypropylsilylene 1,4-phenylene), and copoly(methyl-4,7,10,13-tetraoxatetradecanylsilylene 1,4-phenylene) have been prepared by platinum-catalyzed hydrosilation graft reactions between poly (methylsilylene 1,4-phenylene) and appropriate functionally substituted alkenes. These polymers have been characterized by¹H,¹³C, and²⁹Si NMR as well as by FT-IR and UV-vis spectroscopy. The molecular weight distribution of these polymers has been determined by gel permeation chromatography (GPC), and their glass transition temperatures (T _e) by DSC.     

High-Performance Directional Metallopolyamides. II. Optical Spectroscopic Studies of Metal Chelation

The chelating interaction between metal ions and 4,4-disubstituted-2,2-bipyridyl-containing high-performance polymeric ligands prepared from 2,2-bipyridyl-4,4-dicarboxylic acid and a series of primary aromatic diamines was investigated by optical spectroscopy. Optical spectroscopic studies of the chelation of ruthenium ions by the 2,2-bipyridyl-containing polyamides revealed the formation of distinct ruthenium(II) complexes [Ru^II(poly)L₄] ( _max=530 nm), [Ru^II(poly)₂L₂] ( _max=584 nm), and [Ru^II(poly)₃]²⁺ ( _max=476 nm), while iron(II) ions formed only one complex ( _max=569 nm). The diverse functional features of the polymer repeat unit directly influences the chelation of metal ions.     

Synthesis of soluble polyarylenes containing alternating 4,4′-(1,1′-binaphthyl) and 4,4′-(3,3′-diphenyl)biphenyl structural units

Summary The synthesis and Ni(0) catalyzed homocoupling polymerization of 4,4-bis[5-(trifluoromethanesulfonyloxy)-2-biphenylyl]-1, 1-binaphthyl (9) are described. This polymerization reaction produces a soluble polyarylene containing alternating 4,4-(1,1-binaphthyl) and 4,4-(3,3-diphenyl)biphenyl structural units.     

Shape-selective alkylation of biphenyl over mordenite: cerium exchanged sodium mordenite and unmodified H-mordenite with low SiO2/Al2O3 ratio

Liquid phase isopropylation of biphenyl with propylene was studied over a cerium exchanged sodium mordenite (Ce/NaM25) and a H-mordenite (HM25) with the same SiO₂/Al₂O₃ ratio of 25. Shape-selective catalysis occurred to give 4,4-diisopropylbiphenyl (4,4-DIPS) in high selectivity over Ce/NaM25 under any propylene pressures. HM25 gave 4,4-DIPS shape-selectively under high propylene pressures. However, the reaction was severely deactivated at a conversion of ca. 60% under such a low pressure as 0.8 kg/cm² because of coke formation in the pore. The yields of 4-isopropylbiphenyl (4-IPBP) and 4,4-DIPB decreased with the increase of those of 3-IPBP and 3,4-DIPB because of non-selective alkylation and isomerization at external acid sites that are alive in spite of severe deactivation. No significant isomerization of 4,4-DIPB over Ce/NaM25 was observed even at low propylene pressure. In the case of HM25, the isomerization of 4,4-DIPB to 3,4-DIPB occurred significantly under low propylene pressures, while it decreased under high pressure. These differences are ascribed to the differences of nature of acid sites between Ce/NaM25 and HM25 zeolites.     

Synthesis of new metal-containing side-chain monomers and polymers

New metal-containing vinyl monomers, hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl]benzoyloxy}methacrylate, and the corresponding homopolymers and random copolymers with hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate were synthesized. The compounds were characterized by¹H NMR; their thermal behavior was investigated by means of differential scanning calorimetry. Monomers and polymers containing the ferrocene unit melt at lower temperatures than those derived from the cyclopentadienyl managanese tricarbonyl moiety. The melting temperatures of the monomers and polymers ranged from 399 to about 515 K, Both monomers and polymers failed to exhibit mesogenic behavior. Values ofM _n,M _w,M _w/M _n, and degree of polymerization were obtained by gel permeation chromatography. TheM _n ranged from 16,500 for the copolymer containing hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl] benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 26,000 for the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio.M _w/M _n ranged from 1.6 in the case of the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 2.2 in the case of poly(hexyl-6-oxy{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate).     

Dynamic mechanical properties of crosslinked polyisoprene under deformation

Summary Molecular motions of elastomers under deformations were observed through dynamic mechanical measurements. Composite master curves of dynamic moduli E and E and loss tangent tan over a wide range of frequency and in a state of elongation were obtained by the time-temperature superposition procedure. It is found that both moduli increase with strain, . The slope of the dispersion curve of E become more gradual with the increase in , while that of E is almost unchanged. The increment of E is generally larger than that of E, which does not agree with the N. W. Tschoegl prediction, E ^* ()=f() E _o ^* (), where E ^* () and E _o ^* () are complex moduli at the strain of and O, respectively, and f() is the function of only . The difference in the strain dependence of E from E was found to correspond to the strain dependence of the equilibrium modulus.     

The electrochemical properties of polyaniline derivatives: poly(4,4′-diphenylamine methylenes) and poly(4,4′-diphenylimine methines)

Summary The electrochemical properties of poly(4,4-diphenylamine methylenes) and poly(4,4-diphenylimine methines) were investigated by cyclic voltammetry. A dehydrogenation reaction occured when poly(4,4-diphenylamine methylenes) underwent a electrochemical reaction and transformed to poly(4,4-diphenylimine methines). The fully oxidized poly(4,4-diphenylimine methines) had the electrochemical band gaps of 1.60–1.72 eV, which were found to significantly smaller than those of the fully reduced poly(4,4-diphenylamine methylenes).     

Ethynylene-disilanylene copolymers

Polymers of structure (SiR₂SiR₂-C C-SiR₂SiR₂-C C) _n , in which ethynylene units alternate with disilylene units, have been prepared by two routes: (a) condensation of dichlorodisilanes with dilithium derivatives of 1,2-diethynyldisilanes and (b) ring-opening polymerization of strained cyclic disilanylene-acetylnes, (SiR₂SiR₂C C)₂. The polymers display UV absorption near 240 nm indicative of – conjugation between the Si₂ and the C C moieties. Polymers with R=R=n-Bu or R=n-Bu, R=Ph, undergo solid-state transitions to form liquid crystalline mesophases resembling those observed for many poly(silylenes). Single crystals were obtained for the polymer with R=R=CH₃, by precipitation from dilute cyclohexane solution. The solid-state properties and structures of this family of polymers are discussed.This paper was presented at the Second International Topical Workshop, Advances in Silicon-Based Polymer Science.     

Liquid crystalline polyethers based on conformational isomerism

Summary The synthesis and characterization of copolyethers based on 1-(4-hydroxyphenyl)-2-(2-methyl-4-hydroxyphenyl)ethane (MBPE), 1,8-dibromooctane and each of the following three nonmesogenic bisphenols: 3,4-dihydroxydiphenylmethane (3,4-BPM), 4,4-isopropylidenediphenol (4,4-BPA) and 3,4-isopropylidenediphenol (3,4-BPA) are presented. Copolymers based on MBPE, 3,4-BPM and 1,8-dibromooctane display a nematic mesophase up to compositions containing as much as 70 mol% of 3,4-BPM. The range of mesomorphism decreases on going from 3,4-BPM to 3,4-BPA and to 4,4-BPA. These results demonstrate that structural units derived from parent amorphous and liquid crystalline homopolymers can be isomorphous within the mesophase over a certain range of copolymer composition of the resulting copolymers. Subsequently, the parameters of the mesomorphic phase transitions of these copolymers represent weight averaged values of the corresponding parameters of the parent homopolymers.Part 12: V. Percec and Y. Tsuda, Polymer submitted     

Photochromic polymers

Summary Two soluble photochromic polymers containing 1-(ß-hydroxyethyl)-3,3-dimethyl-6-nitrospiro[2H-1-benzopyran-2,2-indoline] bound on a variously long side chain were prepared. It was found that the discolouration process depends on the length of the side chain to which the photochromic centre is bound.     

Kinetics of copper electrodeposition in citrate electrolytes

The kinetics of copper electrocrystallization in citrate electrolytes (0.5M CuSO₄, 0.01 to 2M sodium citrate) and citrate ammonia electrolytes (up to pH 10.5) were investigated. The addition of citrate strongly inhibits the copper reduction. For citrate concentrations ranging from 0.6 to 0.8 M, the impedance plots exhibit two separate capacitive features. The low frequency loop has a characteristic frequency which depends mainly on the electrode rotation speed. Its size increases with increasing current density or citrate concentration and decreases with increasing electrode rotation speed. A reaction path is proposed to account for the main features of the reduction kinetics (polarization curves, current dependence of the current efficiency and impedance plots) observed in the range 0.5 to 0.8 M citrate concentrations. This involves the reduction of cupric complex species into a compound that can be either included as a whole into the deposit or decomplexed to produce the metal deposit. The resulting excess free complexing ions at the interface would adsorb and inhibit the reduction of complexed species. With a charge transfer reaction occurring in two steps coupled by the soluble Cu(I) intermediate which is able to diffuse into the solution, this model can also account for the low current efficiencies observed in citrate ammonia electrolytes and their dependencies upon the current density and electrode rotation speed.Nomenclature b, b ₁, b ₁ ^* Tafel coefficients (V^–1) - bulk concentration of complexed species (mol cm^–3) - (si*) concentration of intermediate C^* atx=0 (mol cm^–3) - C concentration of (Cu Cit H)^2– atx=0 (mol cm^–3) - C C variation due to E - C concentration of complexing agent (Cit)^3- at the distancex (mol cm^–3) - C _o concentrationC atx=0 (mol cm^–3) - C _o C _o variation due to E - Cv _s bulk concentrationC (mol cm^–3) - (Cit H), (Cu), (Compl) molecular weights (g) - C _dl double layer capacitance (F cm^–2) - D diffusion coefficient of (Cit)^3- (cm²s^–1) - D ₁ diffusion coefficient of C^* (cm²s^–1) - E electrode potential (V) - f ₁ frequency in Equation 25 (s^–1) - F Faraday's constant (96 500 A smol^–1) - i, i ₁, i ₁ ^* current densities (A cm^–2) - i i variation due to E - Im(Z) imaginary part ofZ - j - k ₁, k ₁ ^* , K₁, K ₁ ^* , K₂, K rate constants (cms^–1) - K rate constant (s^–1) - K ₃ rate constant (cm³ A^–1s^–1) - R _t transfer resistance (cm²) - R _p polarization resistance (cm²) - Re(Z) real part ofZ - t time (s) - x distance from the electrode (cm) - Z _f faradaic impedance (cm²) - Z electrode impedance (cm²) Greek symbols maximal surface concentration of complexing species (molcm^–2) - thickness of Nernst diffusion layer (cm) - , ₁, ₂ current efficiencies - angular frequency (rads^–1) - electrode rotation speed (revmin^–1) - =K ^–1(s) - _d diffusion time constant (s) - electrode coverage by adsorbed complexing species - (in0) electrode coverage due toC _s - variation due to E     

Shape-Selective Alkylation of Biphenyl over H-[Al]-SSZ-31 with Propylene

Isopropylation of biphenyl (BP) over [Al]-SSZ-31, a large-pore, one-dimensional zeolite has been studied. Effects of temperature, pressure and SiO₂/Al₂O₃ ratio were examined. SSZ-31 was found to be an active catalyst in the isopropylation of biphenyl with propylene. The selectivity for 4-isopropylbiphenyl (4-IPBP) and 4,4-diisopropylbiphenyl (4,4-DIPB) was high among isopropylbiphenyl (IPBP) and diisopropylbiphenyl (DIPB) isomers, respectively, indicating SSZ-31 shows shape-selective catalysis. The selectivity for 4,4-DIPB decreased with temperature increase; correspondingly the selectivity for thermodynamically more stable isomers (3,3- and 3,4 DIPB) increased with temperature. The yield of IPBP isomers decreased while that of DIPB isomers increased with temperature increase. Pressure showed less effect on conversion; however, increase in pressure suppresses the isomerization of 4,4-DIPB to 3,3- and 3,4-DIPB. Conversion decreased with increase in SiO₂/Al₂O₃ ratio. At low SiO₂/Al₂O₃ ratio of 136, relatively high triisopropylbiphenyl (TriIPB) isomers were formed in bulk products and their amount decreased with increase in SiO₂/Al₂O₃ ratio.     

A solid-state electrochromic device based on complementary polypyrrole/polythiophene derivatives and an elastomeric electrolyte

A device was assembled using optically transparent glass electrodes and combining two complementary electrochromic polymeric materials, poly(4,4-dipentoxy-2,2-bithiophene) and poly(N,N-dimethyl-2,2-bipyrrole). As electrolyte we used an ionically conductive polymer; poly(epichlorohydrin-co-ethylene oxide) containing a lithium salt. The optical contrast in the visible/near infrared region, stability to repeated redox cycles and electrochromic efficiency are reported and discussed.     

Shape-selective isopropylation of biphenyl over a highly dealuminated mordenite: effect of propylene pressure

A highly dealuminated H-mordenite (H-M) catalyzed the selective isopropylation of biphenyl to 4,4-diisopropylbiphenyl (4,4-DIPB). The high selectivity is ascribed to the shape-selective catalysis in mordenite pores. The selectivity of 4,4-DIPB decreased during the isopropylation of biphenyl due to isomerization of 4,4-DIPB under low propylene pressure. The increase of propylene pressure suppressed the isomerization in the isopropylation. 4,4-DIPB itself was isomerized over highly dealuminated H-M under low propylene pressure.     

The photochromism of nitrospiropyran included in γ-cyclodextrin

Summary The inclusion compounds of 1, 3, 3-trimethyl-6-nitrospiro-[2H, 1-benzo-pyran-2, 2-indoline] (NSP) with -cyclodextrin (-CD), 2,3,6,0-permethylated -CD (-MCD), and naphthyl modified -CD (-NCD) showed normal photochromism in the solid state with high light sensitivity comparable with that of NSP dispersed in polymer matrices. This is in sharp contrast with NSP in the crystalline state, which is much less photosensitive. These results suggest that the host cavity offers a sufficient free volume for phototransformation of the guest molecule. The colored form of the inclusion compounds were found to be more stable both chemically upon prolonged UV irradiation and thermally in the dark as compared with that in a PMMA film.     

The effect of support structure on CO2 hydrogenation over a rhodium catalyst supported on niobium oxide

The hydrogenation of CO₂ was investigated over a rhodium catalyst supported on niobium oxide at atmospheric pressure. Niobium oxide was prepared by the hydrolysis of niobium chloride and its crystallitic structure was controlled by calcination temperature. It was found that the activity was lower but the selectivity of C₂₊ hydrocarbons was higher for the and forms than for the and forms of the niobium oxide.     

Synthesis and characterization of poly(1-sila-cis-pent-3-enes) substituted with pendant pyridinyl groups

Poly[1-methyl-1-[3-(3-pyridinyl)propyl]-1-sila-cis-pent-3-ene], poly[1-phenyl-1-[3-(3-pyridinyl)propyl)-1-sila-cis-pent-3-ene], and poly[1-phenyl-1-(4-pyridinyl)-1-sila-cis-pent-3-ene] were synthesized by the anionic ring-opening polymerization of 1-methyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, 1-phenyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, and 1-phenyl-1-(4-pyridinyl)-1-silacyclopent-3-ene, respectively. These are the first polycarbosilanes which contain heterocyclic pyridine units as side-chain substituents. These polymers were characterized by¹H,¹³C, and²⁹Si NMR as well as by IR and UV spectroscopy. The molecular weight distributions were determined by gel permeation chromatography, glass transition temperatures, by differential seanning calorimetry: (DSC) and thermal behavior, by thermogravimetric analysis. (TGA).     

The impedance of the Ledanché cell. I. The treatment of experimental data and the behaviour of a typical undischarged cell

The impedance spectrum of an undischarged commercial Leclanché cell (Ever Ready type SP11) is presented in the forms of the Sluyters plot and the modified Randies plot. The decomposition of the experimental cell impedances into the component parts has been achieved using a computer. The decomposition process and the component processes representing the overall cell behaviour are described.List of symbols R _s in-phase component of (experimental) electrode impedance - R _t charge transfer resistance referred to nominal area of Zn ( cm²) - 1/(C _s) out-of-phase component of (experimental) electrode impedance - angular frequency (= 2f) - R resistance of electrolyte solution - charge transfer resistance - C _L double layer capacitance - C _DL double layer capacitance of electrode referred to nominal area of Zn (F cm^–2) - j –1 - Warburg coefficient - D factor in Equations 1 and 2 - C _s R _s calculated values ofC _s andR _s (first approximation) - C _s R _s calculated values ofC _s andR _s (refined values taking into account the additional network) - C _s R _s calculated values of C_s andR _s (refined values taking into account porosity) - _x resistive part of additional series component (parallel connection) - C _x capacitance part of additional series component (parallel connection) - D factor in Equations 6 and 7