共查询到19条相似文献,搜索用时 109 毫秒
1.
2.
3.
4.
通过LFT-D-CM(长纤维增强热塑性塑料直接在线模压成型)工艺,生产碳纤维增强工程塑料,最大程度地保留了碳纤维在产品中的长度,与玻璃纤维增强材料相比,碳纤维增强工程塑料力学性能优于玻璃纤维增强工程塑料,并且随着纤维含量的增加,材料力学性能提高并可在线回收利用废料,解决了碳纤维增强热固性树脂基复合材料的回收再利用问题,减少能耗及污染。 相似文献
5.
使用熔融浸渍法制备了长玻璃纤维增强聚丙烯复合材料(LFTPP–G),研究了不同纤维含量、不同牵引速度及不同相容剂马来酸酐接枝聚丙烯(PP-g-MAH)添加量对复合材料力学性能的影响。结果表明,玻璃纤维在复合材料体系中起增强增韧作用,复合材料力学性能随纤维含量增加而升高;提高牵引速度可以提高生产效率,但复合材料的力学性能及纤维分散性能随之降低;相容剂PP-g-MAH的加入改善了玻璃纤维与树脂的界面结合。当使用自制的浸渍装置且玻璃纤维质量分数为50%、牵引速度为30 m/min、相容剂PP-g-MAH质量分数2%时,制得LFTPP–G具有较好的综合力学性能,其缺口冲击强度相较于纯聚丙烯树脂提高了1323%。 相似文献
6.
硅灰石与连续玻璃纤维毡组合增强聚丙烯的力学性能 总被引:8,自引:0,他引:8
采用硅灰石与连续玻璃纤维毡组合增强聚丙烯,研究了硅灰石的含量,玻璃纤维毡的面密度、基体树脂的性质及界面改性等对材料力学性能的影响。结果表明:采用硅灰石与连续玻璃纤维毡组合增强,可提高复合材料的拉伸、弯曲强度及模量,但过高的硅灰石含量,会导致拉伸及弯曲强度下降,材料的力学性能随着所用玻璃纤维毡面密度的增大而显著提高,采用偶联剂对硅灰石进行处理及在基体聚丙烯中添加功能化聚丙烯,可改善界面结合、提高材料性能,随着功能化聚丙烯含量的增加,材料的拉伸、弯曲强度及模量有所提高,但含量过高时,会引起材料冲击强度的下降;组合增强材料的性能与基体树脂本身的力学性能密切相关,同时还受基体树脂熔体流动性的影响。 相似文献
7.
8.
9.
10.
Borealis(北欧化工)公司用短玻璃纤维增强高性能(分子量大)PP(聚丙烯)基础树脂的配混料Xmod替代长玻璃纤维增强PP配混料,应用于汽车踏板、行李箱、空气吸入歧管和汽车前端部件等制品的制造。这种新材料Xmod不需专门设计的加工设备和模具,防止玻璃纤维被切断,可以用标准注塑机加工,而且由于采用短玻璃纤维增强,材料熔体流动性好,特别要指出的是制备的最终产品力学性能也更优。Borealis公司指出:一般熔体流动速率40~150g/10min的长玻璃纤维增强牌号要用低分子量基础(母体)树脂,但低分子量导致增强树脂的力学性能低下,而Xmod流动性好,其基… 相似文献
11.
12.
13.
研究了长玻纤和短玻纤增强聚甲基丙烯酸甲酯(PMMA)复合材料的动态流变性能.结果表明,由于长玻纤比短玻纤更易发生缠结,长玻纤增强PMMA复合材料具有更高的动态模量和动态粘度,且其模量和粘度具有更高的浓度依赖性;长玻纤增强PMMA复合材料时,随着玻纤含量的增加,剪切变稀现象更加明显. 相似文献
14.
采用熔融拉挤工艺技术制备了长玻璃纤维增强聚丙烯/聚酰胺6[LFT- (PP/m-PA6)]粒料,并研究了材料的界面相互作用情况、力学性能和流变性能。结果表明, m-PA6改善了PP树脂与玻纤之间的润湿性和浸淆性, 提高了界面粘接强度, 使LFT-(PP/m-PA6)的拉伸强度和弯曲强度增加、刚性增强、韧性基本不变; 当长玻纤含量相同时, 以均聚PP(F401)为基质的长玻纤增强聚丙烯(LFT-PP)和LFT-(PP/m-PA6)的力学性能高于以共聚PP(K712)为基质的LFT-PP和LFT-(PP/m-PA6),特别是缺口冲击强度明显提高;在-30 ℃下,LFT-PP(F401)的缺口冲击强度提高了3.91 %,LFT-PP(K712)的缺口冲击强度提高了7.53 %; m-PA6起到了界面润滑作用, 能使LFT-(PP/m-PA6)的流动性能更好。 相似文献
15.
Two types of long jute fiber pellet consisting of twisted‐jute yarn (LFT‐JF/PP) and untwisted‐jute yarn (UT‐JF/PP) pellets are used to prepare jute fiber–reinforced polypropylene (JF/PP) composites. The mechanical properties of both long fiber composites are compared with that of re‐pelletized pellet (RP‐JF/PP) of LFT‐JF/PP pellet, which is re‐compounded by extrusion compounding. High stiffness and high impact strength of JF/PP composites are as a result of using long fiber. However, the longer fiber bundle consequently affects the distribution of jute fiber. The incorporation of 10 wt % glass fibers is found to improve mechanical properties of JF/PP composites. Increasing mechanical properties of hybrid composites is dependent on the type of JF/PP pellets, which directly affect the fiber length and fiber orientation of glass fiber within hybrid composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41819. 相似文献
16.
Zhaozeng Tao Yatao Wang Jianhua Li Xiaodong Wang Dezhen Wu 《Polymer Composites》2015,36(10):1826-1839
A thermoplastic pultrusion was carried out to prepare the long fiber reinforced thermoplastic (LFT) composites based on polyacetal (POM) matrix on the custom‐designed pultrusion equipment. The investigation on mechanical performance revealed that the POM‐based LFT composites achieved much higher tensile, flexural, and impact strength than the short glass fiber reinforced ones at the same fiber loadings. Such a promising reinforcement effect is attributed to the feature that the residual fiber length in the injection‐molded LFT products is greatly superior to that in short fiber reinforced ones. This takes full advantage of the strength of the reinforcing fiber itself. The scanning electronic microscopy demonstrated that the fiber fracture and fiber pull‐out concurred on the tensile and impact fracture surfaces, and the former preceded the latter. The isothermal crystallization kinetics of the POM‐based LFT composites was also intensively studied, and the results indicated that the crystallinity of POM domain was enhanced by the heterogeneous nucleation of glass fiber, but the crystallization rate was postponed due to the interspace restriction toward crystalline growth caused by long glass fiber. These kinetic parameters provided information on the processing conditions of POM‐based LFT composites for the injection and compression molding. POLYM. COMPOS., 36:1826–1839, 2015. © 2014 Society of Plastics Engineers 相似文献
17.
18.
轻量化、绿色环保和舒适安全性将成为我国汽车用材料未来发展方向,树脂基复合材料将是实现汽车轻量化、塑料化的材料之一.介绍了玻璃纤维毡增强热塑性复合材料(GMT)、长纤维增强热塑性复合材料(LET)、天然纤维增强热塑性复合材料(NMT)和碳纤维增强复合材料(CFRP)等的特点和应用实例分析.树脂基复合材料的应用是汽车轻量化设计和选材的发展趋势. 相似文献
19.
苎麻落麻纤维增强聚丙烯复合材料研究 总被引:9,自引:2,他引:7
本文对苯麻落麻纤维增强聚丙烯(PP)复合材料注射成型过程中苎麻落麻纤维的分散问题和制品的复合工艺进行了研究,用金相显微镜和扫描电镜观察了落麻纤维/PP的断面形貌:将纯PP,苎麻落麻纤维增强PP,玻璃纤维增强PP等复合材料的性能进行了比较。 相似文献