Experimental study of cake formation on heat treated and membrane coated needle felts in a pilot scale pulse jet bag filter using optical in-situ cake height measurement

Pulse-jet bag filters are frequently employed for particle removal from off gases. Separated solids form a layer on the permeable filter media called filter cake. The cake is responsible for increasing pressure drop. Therefore, the cake has to be detached at a predefined upper pressure drop limit or at predefined time intervals. Thus the process is intrinsically semi-continuous. The cake formation and cake detachment are interdependent and may influence the performance of the filter. Therefore, understanding formation and detachment of filter cake is important. In this regard, the filter media is the key component in the system. Needle felts are the most commonly used media in bag filters. Cake formation studies with heat treated and membrane coated needle felts in pilot scale pulse jet bag filter were carried out. The data is processed according to the procedures that were published already [Powder Technology, Volume 173, Issue 2, 19 April 2007, Pages 93-106]. Pressure drop evolution, cake height distribution evolution, cake patches area distribution and their characterization using fractal analysis on different needle felts are presented here. It is observed that concavity of pressure drop curve for membrane coated needle felt is principally caused by presence of inhomogeneous cake area load whereas it is inherent for heat treated media. Presence of residual cake enhances the concavity of pressure drop at the start of filtration cycle. Patchy cleaning is observed only when jet pulse pressure is too low and unable to provide the necessary force to detach the cake. The border line is very sharp. Based on experiments with limestone dust and three types of needle felts, for the jet pulse pressure above 4 bar and filtration velocity below 50 mm/s, cake is detached completely except a thin residual layer (100-200 μm). Uniformity and smoothness of residual cake depends on the surface characteristics of the filter media. Cake height distribution of residual cake and newly formed cake during filtration prevails. The patch size analysis and fractal analysis reveal that residual cake grow in size (latterly) following regeneration initially on the base with edges smearing out, however, the cake heights are not leveled off. Fractal dimension of cake patches boundary falls in the range of 1-1.4 and depends on vertical position as well as time of filtration. Cake height measurements with Polyimide (PI) needle felts were hampered on account of its photosensitive nature.     

浅论袋式收尘器在使用中的技术问题

水泥粉磨系统采用袋收尘技术不应采用旋风筒作预收尘设备;高温条件下的袋收尘技术以降低烟气温度为前提,使用热交换器降温较增湿塔降温好;高温条件下的袋收尘器更应防漏气,确保不发生结露现象;煤磨系统的袋收尘器关键在防燃防爆。为了确保袋收尘器正常运行,应更多地考虑过滤风速、结露与热耗的关系以及系统阻力。     

Distributions of age, thickness and gas velocity in the cake of jet pulsed filters—application and validation of a generations filter model

Different imperfections are observed with jet pulsed filters. They manifest themselves most obviously in the curve of the pressure drop versus time. A convex pressure drop curve indicates cake compaction. But jet pulsed filters frequently show a concave rise of the pressure drop curve. This phenomenon is due to a strongly nonuniform cake area load on the filter and it is generally attributed to incomplete cake removal. Incomplete cake removal takes place when only a fraction of the total filter area is cleaned at the end of a filter cycle or when patchy cleaning prevails. Patchy cleaning means that a jet pulse removes the entire filter cake of only a fraction of the exposed filter area except for a thin adhesive dust layer.In this paper a filter model is proposed in which the different classes of cake thickness are understood to result from different cake generations. A cake becomes one generation older when it survives the jet pulse cleaning at the end of a filtration cycle, although the area that is occupied by the cake on the filter medium is diminished by the jet pulse.This generations filter model can be used to find the distributions of age, thickness and gas velocities in the cake from steady-state operational data. The steady-state, periodic model provides a complete basis for the simulation of heterogeneous gas/solid reactions in the cake of jet pulsed filters.In the model intermediate cake build up during the cleaning procedure is considered. There redeposition of removed filter cake also takes place, and its extent is estimated. The model can also serve to determine from macroscopic process data, if the cleaning system of a filter installation operates in the undesirable mode of patchy cleaning.Experiments from a pilot plant for dry flue gas cleaning are presented and the generations filter model is validated with the experimental data.