Synthesis of electrically conducting copolymers of aniline with o/m-amino benzoic acid by an inverse emulsion pathway

Copolymers of aniline and ortho/meta-amino benzoic acid were synthesized by chemical polymerization using an inverse emulsion pathway. The copolymers are soluble in organic solvents, and the solubility increases with the amino benzoic acid content in the feed. The reaction conditions were optimized with emphasis on high yield and relatively good conductivity (2.5×10⁻¹ S cm⁻¹). The copolymers were characterized by a number of techniques including UV-vis, FT-IR, FT-Raman, EPR and NMR spectroscopy, thermal analysis, SEM and conductivity. The influence of the carboxylic acid group ring substituent on the copolymers is investigated. The spectral studies reveal that the amino benzoic acid groups restrict the conjugation along the polymer chain. The SEM micrographs of the copolymers reveal regions of amorphous and crystalline domain. Thermal studies indicate a marginally higher thermal stability for poly(aniline-co-m-amino benzoic acid) compared to poly(aniline-co-o-amino benzoic acid).     

Low temperature synthesis and dielectric, ferroelectric and piezoelectric study of microwave sintered BaTiO3 ceramics

Barium titanate (BaTiO₃/BT) ferroelectric system was synthesized in single perovskite phase at low temperature by using powders derived from modified solid state reaction (MSSR) and sintered by microwave (MW) processing routes. Conventional calcination temperature was optimized at 900 °C for 4 h. MW sintering of BT samples was carried out at 1100 °C for 30 min to get dense (98% density) ceramics. Room temperature (RT) dielectric constant (?_r) and dielectric loss (tan δ) at 1 kHz frequency of MW sintered BT samples was found to be ∼2500 and 0.03, respectively. Saturated polarization vs. electric field (P-E) loops with remnant polarization (P_r) ∼6 μC/cm² and coercive field (E_c) ∼1.45 kV/cm confirmed the ferroelectric nature of MW sintered BT samples. Piezoelectric coefficient from strain vs. electric field (S-E) loops study was found to be 335 pm/V.     

Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

The effect of synthesis procedure on the structure and properties of palladium/polycarbonate nanocomposites

In this paper, we compare two procedures for the synthesis of palladium (Pd)/polycarbonate (PC) nanocomposites as well as their morphological, optical, thermal and electrical properties. Pd nanoclusters were produced by the reduction of palladium chloride using a variation of Brust's method. Discrete Pd nanoclusters of ∼15 nm size were formed in the absence of PC in the reaction mixture (ex situ method) while agglomeration of Pd nanoclusters was noticed in the presence of PC in the reaction mixture (in situ method). Fourier transform infrared spectroscopy (FTIR) suggests nanoparticle-polymer interactions and polymer conformational changes in the in situ nanocomposite films. Even after having the same Pd content, the ex situ nanocomposites films were found to transmit more light than the in situ nanocomposites. The glass transition temperature (T_g), decreased by ∼16 °C for both the ex situ and in situ samples. Thermogravimetric analysis (TGA) indicated that the presence of Pd nanoclusters significantly improved the thermal stability of the nanocomposites, as evidenced by the enhanced onset of degradation by ∼20 °C and ∼40 °C for the in situ and ex situ nanocomposites, respectively. The electrical conductivity measurement shows a dramatic difference between these nanocomposites with a significantly higher value for the in situ nanocomposite (resistivity = 2.1 × 10⁵ Ωm) compared to the ex situ nanocomposite (resistivity = 7.2 × 10¹³ Ωm).     

Synthesis of laterally attached side-chain liquid crystalline poly(p-phenylene vinylene) and polyfluorene derivatives for the application of polarized electroluminescence

Two series of poly(p-phenylene vinylene) and polyfluorene derivatives (PPV1-PPV4 and PF1-PF5) containing laterally attached penta(p-phenylene) mesogenes were synthesized and characterized. These polymers show nematic liquid crystalline behavior. The optical properties of the polymers were investigated by UV-vis absorption and photoluminescence spectrometers and these polymers were fabricated to form the polarized electroluminescent devices using poly(ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as an alignment layer. In the series of poly(p-phenylene vinylene) derivatives, polymer PPV4 offered the best EL device performance. It emitted yellow light at 588 nm at 4 V. The maximum brightness was about 1337 cd/m² at 9 V with a polarized ratio of 2.6. In another series of polyfluorene derivatives, PF4 offered the best EL device performance with the polarized ratio of 12.4 and a maximum luminescence of 1855 cd/m². In the case of polarized white light, as a consequence of blending small amount of PF4 and PF5 with a host polymer PF2, polarized ratio of up to 10.2 and a maximum brightness of 2454 cd/m² have been attained. The aligned films exhibited pronounced polarized ratio, implying that the polymers exhibit potential for linearly polarized LED application.     

Mesoporous polyaniline or polypyrrole/anatase TiO2 nanocomposite as anode materials for lithium-ion batteries

A functional composite as anode materials for lithium-ion batteries, which contains highly dispersed TiO₂ nanocrystals in polyaniline matrix and well-defined mesopores, is fabricated by employing a novel one-step approach. The as-prepared mesoporous polyaniline/anatase TiO₂ nanocomposite has a high specific surface area of 224 m² g⁻¹ and a predominant pore size of 3.6 nm. The electrochemical performance of the as-prepared composite as anode material is investigated by cyclic voltammograms and galvanostatic method. The results demonstrate that the polyaniline/anatase nanocomposite provides larger initial discharge capacity of 233 mAh g⁻¹ and good cycle stability at the high current density of 2000 mA g⁻¹. After 70th cycles, the discharge capacity is maintained at 140 mAh g⁻¹. The excellent electrochemical performance of the polyaniline/TiO₂ nanocomposite is mainly attributed to its special structure. Furthermore, it is accessible to extend the novel strategy to other polymer/TiO₂ composites, and the mesoporous polypyrrole/anatase TiO₂ is also successfully fabricated.     

Synthesis of a soluble conjugated copolymer based on dialkyl-substituted dithienothiophene and its application in photovoltaic cells

A soluble conjugated alternating 3,5-didecanyldithieno[3,2-b:2′,3′-d]thiophene-thiophene copolymer was synthesized by palladium(0)-catalyzed Stille coupling reaction. The thermal, absorption, emission, electrochemical, and photovoltaic properties of the polymer were examined. A weight-average molecular weight around 6.2 × 10⁴ and a polydispersity index of 1.8 was estimated for the polymer using gel permeation chromatography. The polymer exhibits good thermal stability with decomposition temperature of 340 °C and glass-transition temperature of 136 °C. The polymer shows strong absorption peaked at 505 nm in diluted solution and 518 nm in thin film with an optical band gap 2.0 eV. The polymer exhibits intense emission located at 550 nm in solution and 603 nm in film. The HOMO and LUMO energies of the polymer were estimated to be −5.4 and −3.4 eV, respectively, by cyclic voltammetry. Polymer solar cells were fabricated based on the blend of the polymer and methanofullerene [6,6]-phenyl C61-butyric acid methyl ester (PCBM). The power conversion efficiency of 0.7% was achieved under AM 1.5, 100 mW/cm² using polymer:PCBM (1:4, w/w) as active layer.     

Near-infrared photorefractive polymer composites based on carbon nanotubes

A photorefractive effect at the wavelength of 1064 nm is demonstrated for a composite consisting of an aromatic polyimide and carbon single wall nanotubes. The two-beam gain coupling coefficient and the net gain coefficient are equal to 90 and 65 cm⁻¹, respectively, at 80 V/μm for a nanocomposite containing 0.25 wt% crude nanotube material. The refractive index modulation measured at E₀ = 50 V/μm is close to Δn = 0.004.     

Reactivity of α-pinene epoxide in supercritical solvents

Thermal transformations of α-pinene epoxide in composite supercritical solvents that contain CO₂, lower alcohols (ethanol, isopropyl alcohol) and water were studied in the temperature range of 387-575 K at pressure 13.5-21.5 MPa. Campholenic aldehyde and carveol were shown to be the main products of α-pinene epoxide reactions in supercritical solvents containing water. In the absence of water, thermolysis of α-pinene epoxide in supercritical solvent yields campholenic aldehyde and pinocamphone, with their total amount in the reaction mixture attaining 80%. Suggestions were made on the mechanism of α-pinene epoxide thermal isomerization depending on acidity of supercritical solvent.     

Improved performance of dense TiO2/CdSe coupled thin films by low temperature process

Dense TiO₂ and TiO₂/CdSe coupled nanocrystalline thin films were synthesized onto ITO coated glass substrate by chemical route at relatively low temperature (≤100 °C). TiO₂ films were nanocrystalline and crystallinity disappears after CdSe deposition as evidenced by X-ray powder diffraction. Surface morphology and physical appearance of films were studied from SEM and actual photo-images, reveals dense nature of TiO₂ (10-12 nm spherical grains, faint violet) and CdSe (80-90 nm spherical grains, deep brown), respectively. Presence of two absorption edges in UV spectra implies existence of separate phases rather than composite formation. TiO₂ film was found to have higher water contact angle (71°) than TiO₂/CdSe (61°) and CdSe (56°). I-V and stability tests of photo-electrochemical cells were performed with TiO₂ and TiO₂/CdSe film electrodes (under light of illumination intensity 80 mW/cm²) in lithium iodide as an electrolyte using two-electrode system.     

Synthesis, electroluminescence, and photovoltaic properties of dendronized poly(p-phenylene vinylene) derivatives

Two dendronized poly(p-phenylene vinylene) (PPV) derivatives, ED-PPV and BB-PPV, have been successfully synthesized according to the Gilch route. The obtained polymers possess excellent solubility in common solvents, good thermal stability with 5% weight loss temperature of more than 340 °C. The weight-average molecular weight (M_w) and polydispersity index (PDI) of ED-PPV and BB-PPV are in the range of (1.26-2.34)×10⁵ and 1.37-1.45, respectively. Polymer light-emitting diodes (PLEDs) with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al devices were fabricated, and the PLEDs emitted green-yellow light. The turn-on voltages of the PLEDs based on ED-PPV and BB-PPV were approximately 4.3, and 4.5 V, respectively. The PLED devices of ED-PPV exhibited the maximum luminance of about 157 cd/m² at 10.5 V. Photovoltaic cells with the configuration of ITO/PEDOT:PSS/polymer:C₆₀ (1:1)/Al were also fabricated, and the energy conversion efficiency of the devices based on ED-PPV and BB-PPV was measured to be 0.58, and 0.014%, respectively, under the white light at 75 mW/cm².     

Highly efficient electroluminescent biphenylyl-substituted poly(p-phenylenevinylene)s through fine tuning the polymer structure

A series of novel biphenylyl-substituted PPV derivatives, polymers 1-4, with different substitution patterns, has been synthesized and characterized. These polymers possess excellent solubilities, good thermal stabilities, and high-photoluminescent efficiencies. ¹H NMR measurements indicated that the polymers contain negligible tolane-bisbenzyl (TBB) structural defects. Light-emitting diodes fabricated from the four polymers with the configuration of ITO/PEDOT:PSS (50 nm)/polymer (80 nm)/LiF (0.4 nm)/Ca (20 nm)/Ag emitted a saturated green light and demonstrated maximum current efficiencies of 5.1, 4.5, 4.7, and 1.4 cd/A for polymers 1-4, respectively. The much higher current efficiencies of polymers 1-3 than polymer 4 are ascribed to more balanced charge transport in the polymer layers of the three polymers, which has been confirmed by time of flight (TOF) charge mobility measurement. The hole mobilities of the polymers at the applied electric field of 2.0×10⁵ V/cm are 4.70×10⁻⁶, 3.83×10⁻⁶, 7.21×10⁻⁶, and 1.76×10⁻⁵ cm²/Vs for polymers 1-4. This research indicated that fine tuning the substitution pattern of the polymer side chains is an effective way to optimize the LED device performance by controlling the structural defects as well as balancing the charge mobility of the polymers.     

Electrosynthesis and structural characterization of a novel aryl ether trimer

The structure of a novel trimer formed by three p-tert-butyl anisole moieties via the controlled potential electrolysis of p-tert-butyl anisole was determined by X-ray diffraction method. By cyclic voltammetry, we report a multistep electron transfer, each followed by a chemical reaction, resulting in an ECECEC mechanism. Preparative scale oxidation of p-tert-butyl anisole in dry acetonitrile leads to its two first oligomers. The symmetrical dimer, 2,2′-dimethoxy-5,5′-di-tert-butylbiphenyl, shows that the favored coupling sites are those in the ortho position of the methoxy group. The title compound, namely the 1-methoxy-bis-2,3-(2′-methoxy-5′-tert-butylphenyl)-4-tert-butylbenzene crystallizes in triclinic space group P-1 with a = 10.571(3) Å, b = 11.739(1) Å, c = 12.733(2) Å, α = 74.64(1)°, β = 88.71(2)°, γ = 76.58(2)°, V = 1480.8(5) Å³, and Z = 2. The structural analysis reveals that two p-tert-butyl anisole moieties are linked in ortho position on a third p-tert-butyl anisole fragment.     

The intercalation of C60-containing PEO into layered MnPS3

This paper reports the synthesis and magnetism of a new polymer-inorganic intercalation nanocomposite based on a C₆₀-containing poly(ethylene oxide) (C₆₀-PEO) into layered MnPS₃, which is characterized by XRD, IR and thermal analyses. The lattice expansion (Δd) of the intercalation nanocomposite is about 9.3 Å indicating the successful intercalation. And the charge balance is maintained by K⁺ ions coordinating with PEO chain of C₆₀-PEO polymer, which come from the pre-intercalation compound Mn_1−xPS₃[K_2x(H₂O)_y]. Magnetic measurements indicate that the intercalation nanocomposite (C₆₀-PEO/MnPS₃) exhibits a magnetic phase transition from paramagnetism to ferrimagnetism at about 40 K. And the distinctive hysteresis of M-H relationship further confirms that it is a low temperature ferrimagnetic nanocomposite.     

Preparation, physico-chemical characterization and electrical conductivity measurement studies of an organic-inorganic nanocomposite cation-exchanger: Poly-o-toluidine Zr(IV) phosphate

An organic-inorganic nanocomposite cation-exchanger, i.e. poly-o-toluidine Zr(IV) phosphate was synthesized via sol-gel mixing of an electrical conducting polymer poly-o-toluidine into the matrices of inorganic precipitate of Zr(IV) phosphate. The ion-exchange capacity, chemical stability, effect of eluant concentration, elution behavior, pH titration and thermal studies were also carried out to understand the ion-exchange capabilities. The physico-chemical properties of the material were determined using AAS, CHN elemental analysis, FTIR, TGA-DTA, XRD, TEM and SEM studies. On the basis of distribution studies, the material was found to be highly selective for Hg(II). Its selectivity was examined by achieving some important binary separations like Hg(II)-Pb(II), Hg(II)-Cu(II), Hg(II)-Co(II), Hg(II)-Fe(III), Hg(II)-Sr(II), etc. on its column. This material possessed d.c. electrical conductivity in the semi-conducting range, i.e. 10⁻³ to 10⁻² S cm⁻¹; measured by four-in-line probe d.c. electrical conductivity-measuring technique. The d.c. electrical conductivity of the composite material was found stable upto 110 °C for the composites under ambient conditions.     

Synthesis and characterization of a novel unsaturated polyester based on poly(trimethylene terephthalate)

Unsaturated aromatic polyesters were obtained by glycolysis of poly(trimethylene terephthalate) with cis-2-buten-1,4-diol followed by a solid-state polymerization. The glycolysis was performed in a batch mode as well as through a continuous process in a twin screw extruder. The degradation and subsequent rebuilding of the polymer chain during the course of reaction was followed by means of inherent and melt viscosity measurements, and ¹H NMR terminal group analysis of the intermediates and the final products. Structural investigations revealed that this new approach resulted in melt processible unsaturated polyesters with cross-linkable sites having similar characteristics to that of the virgin saturated polyester. Although the processing temperature for the different reaction steps was sufficiently high (180−260 °C), no thermally induced cross-linking of the incorporated unsaturated bonds could be evidenced indicating that the obtained products remained stable during the production stage. For comparison purposes, a commercial unsaturated polyester (Vestodur^©) was included in the investigations. UV irradiation of thin polyester films did not result in cross-linked products but in cis-trans isomerization of the incorporated bisoxybutenyl unit.     

Novel polyion complex with interpenetrating polymer network of poly(acrylic acid) and partially protected poly(vinylamine) using N-vinylacetamide and N-vinylformamide

Poly(vinylamine), the simplest polycation with primary amines, was applied to interpenetrating polymer networks (IPN) with poly(acrylic acid). N-Vinylformamide (NVF) was employed for amino-protected monomers to control electrostatic balance. pH-responsivities of IPNs varied, depending on the hydrolysis conditions and acrylic acid (AAc) concentration of the second network. Poly(N-vinylacetamide)-co-poly(N-vinylformamide) (4/6, mol/mol) was employed for the first network, subsequently hydrolyzed with 50% amide groups, and the second network was polymerized with 0.25 mol L⁻¹ AAc, extremely shrunken hydrogels with polyion complex were formed at pH 7, showing that the controlled amount of highly active primary amines are available in IPN.     

Direct electrochemistry and electrocatalysis of cytochrome c based on chitosan-room temperature ionic liquid-carbon nanotubes composite

A robust and effective composite film combined the benefits of room temperature ionic liquid (RTIL), chitosan (Chi) and multi-wall carbon nanotubes (MWNTs) was prepared. Cytochrome c (Cyt c) was successfully immobilized on glassy carbon electrode (GCE) surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Cyt c were investigated in detail. A pair of well-defined and quasi-reversible redox peaks of Cyt c was obtained in 0.1 mol L⁻¹ pH 7.0 phosphate buffer solution (PBS), indicating the Chi-RTIL-MWNTs film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0 × 10⁻⁶ to 2.6 × 10⁻⁴ mol L⁻¹, with a detection limit of 8.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The apparent Michaelis-Menten constant (K_m) was calculated to be 0.45 ± 0.02 mmol L⁻¹. Moreover, the modified electrode displayed a rapid response (5 s) to H₂O₂, and possessed good stability and reproducibility. Based on the composite film, a third-generation reagentless biosensor could be constructed for the determination of H₂O₂.     

Synthesis and characterization of temperature-responsive copolymer of PELGA modified poly(N-isopropylacrylamide)

Novel amphiphilic PELGA modified temperature-responsive copolymer, [(poly(methoxyethylene glycol)-co-poly(lactic acid)-co-poly-(glycolic acid))acrylate-co-poly(N-isopropylacrylamide)-co-poly(N-hydroxymethylacrylamide)] (PELGAA-co-PNIPAAm-co-PNHMAAm) was synthesized by incorporating PELGA as the amphiphilic moiety into poly(N-isopropylamide) with various LA/GA ratios. Polymers obtained were characterized by FT-IR, GPC, ¹H-NMR and DSC. The lower critical solution temperature (LCST) of the copolymeric nanoparticles was 40±0.6 °C, the critical aggregation concentration (CAC) was 18 mg L⁻¹, and reversible change in nanoparticle size related to temperature was fluctuated between 210±10 and 109±26 nm, while change in zeta potential of the nanoparticles was between −36±6 and −26±4 mV. The transmission electron microscopy (TEM) images of nanoparticles were also presented.     

Synthesis and lithographic evaluation of poly[(methacrylic acid tert-butyl cholate ester)-co-(γ-butyrolactone-2-yl methacrylate)]

Poly[(methacrylic acid tert-butyl cholate ester)-co-(γ-butyrolactone-2-yl methacrylate)] was synthesized and evaluated as a new 193-nm chemically amplified photoresist. This polymer showed good thermal stability up to 240 °C and had a good transmittance at 193 nm. This material showed good resistance to CF₄-reactive ion etching. The resist patterns of 0.15 μm feature size were obtained at a dose of 11 mJ cm⁻² using an argon fluoride excimer laser stepper.