Aligned silver nanorod arrays as substrates for surface-enhanced infrared absorption spectroscopy

Preferentially aligned silver nanorod arrays prepared by oblique angle vapor deposition were evaluated as substrates for surface-enhanced infrared absorption (SEIRA) spectroscopy. These nanorod arrays have an irregular surface lattice and are composed of tilted, cylindrically shaped nanorods that have an average length of 868 nm +/- 95 nm and an average diameter of 99 nm +/- 29 nm. The overall enhancement factor for chemisorbed organic films of para-nitrobenzoic acid (PNBA) deposited onto the Ag nanorod arrays analyzed by external reflection SEIRA was calculated to be 31 +/- 9 compared to infrared reflection-absorption spectroscopy (IRRAS) obtained from a 500 nm Ag film substrate. This enhancement is attributed to the unique optical properties of the nanorod arrays as well as the increased surface area provided by the nanorod substrate. SEIRA reflection-absorbance intensity was observed with both p- and s-polarized incident radiation with angles of incidence ranging from 25 degrees to 80 degrees . The largest intensity was achieved with p-polarization and incident angles larger than 75 degrees . Polarization-dependent ultraviolet/visible/near-infrared (UV/Vis/NIR) spectra of the nanorod arrays demonstrate that the red-shifted surface plasmon peaks of the elongated nanorods may be partially responsible for the observed SEIRA response. The SEIRA detection limit for the Ag nanorod arrays was estimated to be 0.08 ng/cm(2). Surface-enhanced Raman scattering (SERS) and SEIRA analysis of chemisorbed PNBA utilizing the same nanorod substrate is demonstrated.     

Integrate silver colloids with silicon nanowire arrays for surface-enhanced Raman scattering

A facile method to prepare uniform and reproducible surface-enhanced Raman scattering (SERS) substrates is presented. Quasi-spherical silver colloids prepared by microwave heating and wafer-scale uniform silicon nanowire (SiNW) arrays fabricated via wet chemical etching were united together as SERS substrates. The novel SERS substrates displayed stronger Raman enhancement than conventional silver colloids as well as outstanding uniformity and reproducibility in our experiments. In addition, it was found that the cross section of SiNW arrays possessed stronger enhancement activity than the front side. The enhancement effects of two adjacent SiNWs (as a simplification of SiNW arrays) were evaluated by the finite difference time domain (FDTD) method.     

Silver nanorod arrays as a surface-enhanced Raman scattering substrate for foodborne pathogenic bacteria detection

Surface-enhanced Raman scattering (SERS) using novel silver nanorod array substrates has been used for the detection of pathogenic bacteria. The substrate consists of a base layer of 500 nm silver film on a glass slide and a layer of silver nanorod array with a length of approximately 1 microm produced by the oblique angle deposition method at a vapor incident angle of 86 degrees . Spectra from whole cell bacteria, Generic Escherichia coli, E. coli O157:H7, E. coli DH 5alpha, Staphylococcus aureus, S. epidermidis, and Salmonella typhimurium, and bacteria mixtures have been obtained. This SERS active substrate can detect spectral differences between Gram types, different species, their mixture, and strains. Principal component analysis (PCA) has been applied to classify the spectra. Viable and nonviable cells have also been examined, and significantly reduced SERS responses were observed for nonviable cells. SERS detection of bacteria at the single cell level, excited at low incident laser power (12 micro W) and short collection time (10 s), has also been demonstrated. These results indicate that the SERS-active silver nanorod array substrate is a potential analytical sensor for rapid identification of microorganisms with a minimum of sample preparation.     

Dynamic rastering surface-enhanced Raman scattering (SERS) measurements on silver nanorod substrates

Surface-enhanced Raman spectra of a thiol-modified biotin derivative on oblique-angle-deposited silver nanorod (AgNR) array substrates were measured using both static and rotating rastering methods. We find that the rotating rastering method has a strong tendency to decrease the point-to-point relative standard deviation (RSD) compared to static measurements as well as decrease the effects of cumulative excitation exposure. The AgNR substrates treated with the modified biotin typically demonstrate intra-substrate RSDs of <10%, with an average RSD of ～3% when the rastering radius r=1 mm. The quantitative studies on the relationship between rastering radius, sampling area, and rastering frequency show that only the rastering radius appears to have significant effect on the measured RSD. Our results demonstrate that under the proper measurement and sample preparation conditions, the Ag nanorod substrates are very uniform.     

Linker-molecule-free gold nanorod layer-by-layer films for surface-enhanced Raman scattering

This paper reports a methodology for synthesizing and ordering gold nanorods into two-dimensional arrays at a water/hexane interface. This preparation method allows the systematic control of the nanoparticle film thickness. An investigation into the thickness-dependent surface-enhanced Raman scattering (SERS) of the adsorbed molecules revealed the nanorod (NR) films to have 1 order of magnitude stronger SERS enhancement than the nanosphere (NS) under similar experimental conditions. The exposed surface areas of the prepared NR and NS films were analyzed using electrochemical methods, and it was found that they had comparable exposed surface areas. Therefore, the order of magnitude difference in the enhancement factor was not due to the differences in surface area but to their intrinsic difference in the optical coupling of each film. The difference was attributed to the high density of junction points with the NR films in comparison with the corresponding NS films. Scanning emission microscopy showed that the NR films have line contacts with each other but the NS films have point contacts, which can explain the difference in SERS intensity between the NR and NS films.     

Ag nanorod arrays tailored for surface-enhanced Raman imaging in the near-infrared region

Using a dynamic oblique angle deposition technique, we demonstrate the direct formation of Ag nanorods with quasi-parallel major axes on a template layer of oxide having a strongly anisotropic surface morphology. The optical properties of the nanorods are tuned by varying the deposition conditions without any pre-?or post-treatment, and the resulting Ag nanorod arrays exhibit high surface-enhanced Raman scattering (SERS) activity. In addition to high macroscopic uniformity over a large area, our nanorod arrays contain a high density of isolated nanorods. Using the optimum Ag nanorod arrays, the SERS imaging of the microdroplets of a rhodamine 6G solution is successfully demonstrated. The space resolution of the imaging is of the order of at least a few μm. These features are suitable for the SERS imaging of biomaterials.     

Preparation of silver nanoparticles by photo-reduction for surface-enhanced Raman scattering

A substrate for surface-enhanced Raman scattering (SERS) has been developed. Based on the surface-catalyzed reduction of Ag⁺ by citrate on the silver nanoparticles surface under light irradiation, small silver seeds on a quartz slide can be enlarged. The optical properties and characteristics of the silver films have been investigated by ultraviolet-visible spectroscopy, scan electron microscope and atomic force microscopy (AFM). The results indicate that the particle size and shape are different at different reduction time. At the first 3 h, some triangular and hexagonal nanoparticles formed; with the reduction proceeding, the shape of the silver particles became irregular and the size became larger. The silver films obtained are very suitable as SERS active substrate. The relationship between SERS intensity and the reduction time has been investigated for 1,4-bis[2-(4-pyridyl)ethenyl]-benzene molecule adsorbed on the silver film. The SERS intensity reached a maximum at 8 h reduction. The AFM measurements indicate that roughness features with an average size of 100 nm are present on the surface, which yielded the strongest SERS signal. Pyridine was used as a probe molecule to investigate the enhancement factor (EF) of the silver films. According to the formalism of Tian and co-workers, the EF of the silver films is estimated to be 3.4 × 10⁵. The silver film that can remain active for more than 50 days would seem to be suitable for various analytical applications.     

Facile fabrication of gold nanoparticle arrays for efficient surface-enhanced Raman scattering

An effective and facile method for the fabrication of a surface-enhanced Raman scattering (SERS)-active film with closely packed gold nanoparticle (AuNP) arrays is proposed by self-assembly of different sizes (16, 25, 40 and 70?nm) of AuNPs at a toluene/water interface with ethanol as the inducer. The as-prepared AuNP arrays exhibit efficient Raman scattering enhancement, and the enhancement factors estimated using p-aminothiophenol as a probe molecule range from 10(5) to 10(7). This is attributed to the coupling electromagnetic SERS enhancement mechanism with additional localization field within closely packed AuNPs, which have greater SERS activity and reproducibility than that on aggregates and on self-assembled monolayers of isolated AuNPs on glass.     

Polarization-dependent surface-enhanced Raman scattering from a silver-nanoparticle-decorated single silver nanowire

Single silver nanowires produced by DC electrodeposition in porous anodic alumina templates were surface-functionalized with the bifunctional molecule 4-aminobenzenthiol (ABT) then exposed to aqueous silver nanoparticles resulting in a silver nanoparticle-decorated silver nanowire. The polarization dependent surface-enhanced Raman (SERS) signal from this system showed significant intensity anisotropy when measured at a midsection of the nanowire, where the largest SERS intensities were observed when the incident light was polarized perpendicular to the nanowire's long axis but was almost isotropic near the tip of the nanowire. The observed effects were accounted for in terms of the electromagnetic fields concentrated in the collection of hot spots created through the ABT-linker-driven nanoparticle-nanowire self-assembly process.     

Active control of silver nanoparticles spacing using dielectrophoresis for surface-enhanced Raman scattering

We demonstrate an active microfluidic platform that integrates dielectrophoresis for the control of silver nanoparticles spacing, as they flow in a liquid channel. By careful control of the nanoparticles spacing, we can effectively increase the surface-enhanced Raman scattering (SERS) signal intensity based on augmenting the number of SERS-active hot-spots, while avoiding irreversible aggregation of the particles. The system is benchmarked using dipicolinate (2,6-pyridinedicarboxylic acid) (DPA), which is a biomarker of Bacillus anthracis. The validity of the results is discussed using several complementing characterization scenarios.     

Plasma reduction of silver compounds for fabrication of surface-enhanced Raman scattering substrates

Several silver compounds were reduced by low-pressure air plasma to produce porous nanostructured surfaces as surface-enhanced Raman scattering (SERS) substrates. This method is advantageous because substrates are easy to prepare and the silver metal surface is inherently clean without spectroscopic background. Silver compounds were melted into 1-2 mm slugs on quartz slides and plasma treated for different lengths of time. Silver chloride was found to be the best compound to make reproducible and stable SERS substrates. SERS activity of the substrates was tested using L-tryptophan, 4-mercaptobenzoic acid, and adenine.     

Self-assembly nanoparticle based tripetaloid structure arrays as surface-enhanced Raman scattering substrates

This paper reports a novel highly ordered tripetaloid structure array (TPSA) which performs very well as an active surface-enhanced Raman scattering (SERS) substrate. The TPSA is easily fabricated by anisotropic etching of a self-assembly silica-nanoparticle bilayer and a subsequent metal deposition step, with notable uniformity and reproducibility. Electromagnetic simulation indicates that the narrow inter-gaps and edge protrusions in the TPSA act as hot spots. In addition, the peak electromagnetic field intensity in the inter-gaps changes slightly and periodically as the polarization of the incident light varies from 0°?to 360°. SERS experiments show that the SERS enhancement factor (EF) of a Au-film-covered TPSA is 12 times higher than that of regular Au-film-over-nanoparticles, and not sensitive to the polarization of the incident light. The spatially averaged EF of the TPSA is as high as 5.7?×?10(6), and the local EF of its hot spots is much higher.     

Reproducible surface-enhanced Raman scattering spectra of bacteria on aggregated silver nanoparticles

Surface-enhanced Raman scattering (SERS) is proven to be a powerful technique for rapid identification and discrimination of microorganisms. However, due to the heterogeneous nature of the samples, the acquisition of reproducible spectra hinders the further development of the technique. In this study, we demonstrate the influence of the experimental conditions on SERS spectra. Then, we report a simple sample preparation method coupled with a light microscope attached to a Raman spectrometer to find a proper spot on the sample to acquire reproducible SERS spectra. This method utilizes the excited surface plasmons of the aggregated silver nanoparticles to visualize the spots on the sample. The samples are prepared using the concentrated silver colloidal solutions. The collection time for one spectrum is 10 s and each spectrum is a very good representative of the other spectra acquired from the same sample. The nature of the surface charge of the silver nanoparticles influences the spectral features by determining the strength of the interactions between nanoparticles and bacteria and the aggregation properties of the nanoparticles. Although increasing the colloid concentration in the sample resulted in reproducible spectra from arbitrary points on the sample, a great variation from sample to sample prepared with the different colloidal solution concentrations is observed.     

Inverted size-dependence of surface-enhanced Raman scattering on gold nanohole and nanodisk arrays

Surface-enhanced Raman scattering (SERS) on gold nanohole and nanodisk arrays with precisely controlled size and spacing fabricated via electron beam lithography was investigated. These nanostructures exhibit strong SERS signals at 785 nm excitation but not at 514 nm. When the edge-to-edge distance is maintained, enhancement increases for nanoholes but decreases for nanodisks as diameter is increased. It is shown that the observed enhancement results from the local surface plasmon resonance wavelength shifts to the near-infrared regime as nanohole diameter increases. The large tolerance on dimensions and the empty space confined by nanoholes suggest promise for their use as a functional component in sensing, spectroscopy, and photonic devices.     

Dispersible gold nanorod dimers with sub-5 nm gaps as local amplifiers for surface-enhanced Raman scattering

We report the synthesis of solution-dispersible, 35 nm diameter gold nanorod dimers with gaps as small as ～2 nm for surface-enhanced Raman scattering (SERS). Using on-wire lithography (OWL), we prepared tailorable dimers in high yield and high monodispersity (～96% dimers) that produce both large and reproducible SERS signals with enhancement factors of (6.8 ± 0.7) × 10(8) for single dimers in air and 1.2 × 10(6) for ensemble-averaged solution measurements. Furthermore, we show that these structures, which are the smallest ever made by OWL, can be used to detect molecules on flat surfaces and in aqueous solutions. When combined, these attributes with respect to sensitivity, reproducibility, and tailorability lead to a novel and powerful local amplification system for SERS applications.     

Potential-dependent surface-enhanced Raman scattering from adsorbed thiocyanate for characterizing silver surfaces with improved reproducibility

Surface-enhanced Raman scattering (SERS) spectroelectrochemistry is used to characterize electrochemically roughened and highly polished polycrystalline silver SERS-active substrates. Changes in the nitrile stretching vibrational mode of adsorbed thiocyanate are used as an in situ spectroscopic probe: the potential dependence of band position (Stark tuning), shape, and scattering intensity of this mode are measured in order to investigate differences between SERS-active sites found on smooth and roughened electrode surfaces. Results obtained from thiocyanate adsorbed onto two different types of highly polished Ag surfaces (alumina and diamond polishing) show discrete populations of SERS-active adsorption sites that remain stable over a wide potential range. This behavior stands in contrast to that observed on electrochemically roughened surfaces, where very strong Stark tuning, large vibrational bandwidths, and irreversible loss of SERS enhancement upon negative potential excursions can be attributed to a diverse population of labile SERSactive sites that exhibit strong charge-transfer interactions with the adsorbate and large chemical SERS enhancement.     

Novel Ag-Cu substrates for surface-enhanced Raman scattering

Ag dendrites were deposited on rough Cu plate by a simple galvanic displacement process between Ag ion and Cu under room temperature. Surface-enhanced Raman scattering (SERS) performances have been studied using Rhodamine 6G (R6G) probe molecules on this kind of Ag-Cu substrates. The high SERS enhancements are attributed to the highly branched Ag dendritic nanostructures and Ag nanoparticles formed on the trunks, branches, and even leaves.     

Novel method for preparing controllable and stable silver particle films for surface-enhanced Raman scattering spectroscopy

A new surface-enhanced Raman scattering (SERS) active substrate has been developed based on our previous study. Small silver nanoparticles on a quartz slide can be enlarged by using a mixture of commercially available reagents called Silver Enhancer and Initiator. The optical properties and characteristics of the new substrate have been investigated by ultraviolet-visible (UV-Vis) spectroscopy and atomic force microscopy (AFM). The results indicate that the small silver nanoparticles grow and some silver aggregates emerge on the quartz slide after the slide is immersed into the Silver Enhancer and Initiator Mixture (SEIM). The average diameter of the silver nanoparticles on the substrate becomes approximately double after the immersion into SEIM for 20 s. 1,4-bis[2-(4-pyridyl)ethenyl]-benzene (BPENB) was used as a Raman probe to evaluate the enhancement ability of the new silver substrate. It has been found that the SERS intensity can be increased about 10 times by using the substrate treated by SEIM compared with that without being treated by SEIM. Interestingly enough, the SERS enhancement increases with time. This may be due to the reorganization of silver nanoparticles on the quartz surface. The new substrate can remain active for more than 90 days. The adsorption mode of BPENB on the new substrate and the dependence of the BPENB configurations on the concentration of BPENB in methanol solution have also been investigated by SERS or UV-Vis spectroscopy. The SERS spectra of a self-assembled monolayer (SAM) BPENB film adsorbed on a silver substrate treated by SEIM show that BPENB molecules are chemically absorbed through the Ag-N bond. Consequently, a nearly perpendicular orientation of BPENB on the silver surface is proposed. The SERS spectra of BPENB SAMs on the new substrates fabricated from methanol solutions with different concentrations are compared. The concentration dependence of the SERS spectra reveals that the BPENB molecules are adsorbed on the silver film as monomers when the film is prepared from the solution with a lower concentration (<4 x 10(-6) M) and as aggregates when it is prepared from the solution with a higher concentration (>1 x 10(-5) M).