Surface grafting of polymer onto carbon thin film

The surface grafting of polymers onto carbon thin film deposited on a glass plate was achieved by two methods: the graft polymerization initiated by initiating groups introduced onto the surface; and the trapping of polymer radicals by surface aromatic rings of the thin film. It was found that the radical and cationic graft polymerization of vinyl monomers are initiated by azo and acylium perchlorate groups introduced onto the surface, respectively, and the corresponding polymers are grafted onto the surface: the surface grafting of polymers were confirmed by the contact angle of the surface with water. In addition, the anionic ring-opening alternating copolymerization of epoxides with cyclic acid anhydrides was found to be initiated by potassium carboxylate groups on the carbon thin film to give the corresponding polyester-grafted carbon thin film. On the other hand, polymer radicals formed by the decomposition of azo polymer, such as poly(polydimethylsiloxane-azobiscyanopentanoate) and poly(polyoxyethylene-azobiscyanopentanoate), were successfully trapped by the surface aromatic rings of carbon thin film and polydimethylsiloxane and polyoxyethylene were grafted onto the surface. © 1995 John Wiley & Sons, Inc.     

Effect of initiating groups introduced onto ultrafine silica on the molecular weight polystyrene grafted onto the surface

Summary The effect of initiating groups introduced onto silica surface on the molecular weight of grafted polystyrene chain was investigated. By the treatment of polystyrene-grafted silica with aqueous solution of alkali, surface grafted polystyrene was isolated from the surface. The molecular weight of polystyrene grafted onto the silica obtained from the radical graft polymerization initiated by peroxyester groups introduced onto the surface was found to be much larger than that from the cationic polymerization initiated by acylium perchlorate groups. The number of grafted polystyrene in the radical polymerization, however, was much less than that in the cationic polymerization. Furthermore, the effect of molecular weight of grafted polystyrene on the dispersibility of silica in tetrahydrofuran was examined.     

Surface grafting of polymers onto ultrafine silica: cationic polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic graft polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface was investigated. The introduction of benzylium perchlorate groups onto the surface was achieved by the reaction of silver perchlorate with surface benzyl chloride groups, which were introduced by the treatment of silica with 4-(chloromethyl)phenyltrimethoxysilane. The cationic graft polymerization of styrene and cationic ring-opening polymerization of -caprolactone were found to be initiated by the surface benzylium perchlorate groups and the corresponding polymers were grafted onto the surface. The percentage of grafting onto silica surface decreased with increasing polymerization temperature, because chain transfer reaction of growing polymer cation is accelerated with increasing polymerization temperature.     

Surface grafting of polymers onto glass plate: Polymerization of vinyl monomers initiated by initiating groups introduced onto the surface

The surface grafting of polymers onto a glass plate surface was achieved by the polymerization of vinyl monomers initiated by initiating groups introduced onto the surface. Azo groups were introduced onto the glass plate surface by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with isocyanate groups, which were introduced by the treatment with tolylene-2,4-diisocyanate. The radical polymerization of various vinyl monomers was initiated by azo groups introduced onto the glass plate surface and the corresponding polymers were grafted from the surface: The surface grafting of polymers was confirmed by IR spectra, and the contact angle of surface, with water. The contact angle of the glass plate increased by the grafting of hydrophobic polymers, but decreased by the grafting of hydrophilic polymers. The radical postpolymerization was successfully initiated by the pendant peroxycarbonate groups of grafted polymer on the surface to give branched polymer-grafted glass plate. The cationic polymerization of vinyl monomers was also successfully initiated by benzylium perchlorate groups introduced onto the glass plate surface and the corresponding polymers were grafted onto the surface. The contact angle of the glass plate surface obtained from the cationic polymerization of styrene was larger than that obtained from the radical polymerization. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2165–2172, 1997     

Surface grafting of polymers onto ultrafine silica: Cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface was investigated. The oxoaminium perchlorate groups were successfully introduced by treatment of nitroxyl radicals on silica surface with perchloric acid. The introduction of the nitroxyl radicals was achieved by reaction of 4-hydroxy-2,2,6,6-tetramethyl-piperidinyloxy radical with acid anhydride groups on the surface. The cationic polymerization of isobutyl vinyl ether, N-vinylcarbazole, 2,3-dihydrofuran, and -butyrolactone was initiated by oxoaminium perchlorate groups introduced onto the surface and the corresponding polymers were grafted onto the surface through the propagation of grafted polymer chain from the surface oxoaminium perchlorate groups.     

Surface grafting of polymers onto aramid powder: graft polymerization of vinyl monomers initiated by azo groups introduced onto the surface of aramid powder

The radical graft polymerization of vinyl monomers onto the surface of aramid powder, i.e., poly(p-phenylene terephthalamide) powder, initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto the aramid surface was achieved by the reaction of surface acyl chloride groups, which were introduced by the treatment of aramid powder with adipoyl dichloride, with 2,2′-azobis[2-(2-imidazolyn-2-yl)propane] in the presence of pyridine: the amount of azo groups thus introduced onto the surface was determined to be 0.57 mmol/g by elemental analysis. It was found that the polymerizations of methyl methacrylate (MMA) and styrene were successfully initiated by the azo groups on the surface and that the corresponding polymers were grafted onto the surface. The percentage of surface grafting of polystyrene and poly(methyl methacrylate) (PMMA) increased up to 37.6 and 26.5%, respectively. Thermogravimetric analysis of polymer surface-grafted aramid powder confirmed that the grafting of polymers is limited on the surface. The polymerization rate was found to bear a first-order dependence on the concentration of aramid powder having azo groups. This suggests that in graft polymerization, unimolecular termination preferentially proceeds.     

Cationic grafting from carbon black

Summary The cationic ring-opening copolymerization of tetrahydrofuran (THF) with a cyclic acid anhydride such as phthalic anhydride (PAn) and maleic anhydride was initiated by acylium perchlorate groups on carbon black to give alternating copolymer, i.e., polyester. Epichlorohydrin was found to act as effective promoter in the copolymerization. The polyester formed was effectively grafted from carbon black depending upon the propagation of the polymer from the surface: the grafting ratio of polyester from THF and PAn was increased up to about 65% with an increase in conversion. The polyester-grafted carbon black gave a stable colloidal dispersion in chloroform.     

Cationic Graft Polymerization onto Silica Nanoparticle Surface in a Solvent-Free Dry-System

For the purpose of the prevention of the environmental pollution and the simplification of reaction process, the scale-up synthesis of polymer-grafted silica nanoparticle by surface initiated cationic ring-opening graft polymerization of 2-methyl-2-oxazoline (MeOZO) in a solvent-free dry-system was investigated. The introduction of iodopropyl groups onto the silica surface as initiating group was carried out by the reaction of silanol groups with 3-iodopropyl- trimethoxysilane in a solvent-free dry-system. The graft polymerization of MeOZO onto silica nanoparticle surface in a solvent-free dry-system was initiated by spraying the monomer onto the surface having iodopropyl groups and the polymerization was conducted in powder fluid system under nitrogen. After the polymerization, unreacted MeOZO was readily removed under high vacuum. It was found that the cationic ring-opening polymerization of MeOZO was successfully initiated in the solvent-free dry-system to give polyMeOZO-grafted silica nanoparticles. The maximum grafting of polyMeOZO obtained from the polymerization initiated by iodopropyl groups on the surface reached 47.7 %. The percentage of grafting and grafting efficiency during the cationic ring-opening graft polymerization in the solvent-free dry-system were considerably larger than those in solution system. This suggests that chain transfer reaction from surface growing cation to monomer was effectively inhibited in the solvent-free dry-system.     

Grafting of vinyl polymers onto VGCF surface and the electric properties of the polymer-grafted VGCF

The graft polymerization of vinyl monomers onto vapor grown carbon fibers (VGCF) initiated by the system consisting of molybdenum hexacarbonyl (Mo(CO)₆) and trichloroacetyl (COCCl₃) groups introduced onto the surface was investigated. The introduction of trichloroacetyl groups onto VGCF surface was successfully achieved by the reaction of carboxyl groups on VGCF surface with trichloroacetyl isocyanate. It was found that the radical graft polymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and glycidyl methacrylate (GMA) is successfully initiated by the system consisting of Mo(CO)₆ and COCCl₃ groups introduced onto the surfaces. In the polymerization, the corresponding vinyl polymers were effectively grafted onto the VGCF surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mo(CO)₆: the percentage of PMMA grafting reached 40%. Polymer-grafted VGCF gave a stable colloidal dispersion in good solvents for grafted polymer. The electric resistance of composite prepared from the polymer-grafted VGCF suddenly increased in organic solvent vapor over 10³ times, and returned to initial resistance when it was transferred into dry air. These results indicate that such composites can be used as novel gas sensors.     

Graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto silica surface by Michael addition

The introduction of peroxycarbonate groups onto a silica surface and the graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto a silica surface were investigated. The introduction of peroxycarbonate groups onto a silica surface was achieved by Michael addition of amino groups introduced onto the silica surface to t‐butylperoxy‐2‐methacryloyloxyethylcarbonate (HEPO). The amount of peroxycarbonate groups was determined to be 0.17 mmol/g. The graft polymerization of various vinyl monomers such as styrene (St), N‐vinyl‐2‐pyrrolidinone (NVPD), and 2‐hydroxyethyl methacrylate (HEMA) was initiated by peroxycarbonate groups introduced onto the silica surface to give the corresponding polymer‐grafted silicas. The percentage of poly(St)‐grafting reached about 120% after 5 h. This means that 1.20 g of poly(St) is grafted onto 1.0 g of silica. The surface of poly(St)‐grafted silica shows a hydrophobic nature, but the surfaces of poly(NVPD) and poly(HEMA)‐grafted silica show a hydrophilic nature. Furthermore, the poly(St)‐grafted silica was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1491–1497, 1999     

Ring-opening polymerization of 2-oxazolines initiated by chloromethyl groups introduced onto carbon black surface

Summary The ring-opening polymerization of 2-oxazolines (OXZs) was found to be initiated by chloromethyl groups introduced onto carbon black surface. The introduction of chloromethyl groups onto the surface was achieved by the reaction of carbon black with 3,3-bischloromethylbenzoyl peroxide in carbon tetrachloride. During the polymerization, poly-OXZs were grafted from carbon black based on the propagation of the polymers from the surface: percentage of grafting increased with an increase of conversion and reached 40–60%. The polymerization was accelerated by the addition of potassium iodide. Poly-OXZ-grafted carbon black produced stable colloidal dispersions in both hydrophobic and hydrophilic solvents.     

Graft polymerization of vinyl monomers from initiating groups introduced onto polymethylsiloxane-coated titanium dioxide modified with alcoholic hydroxyl groups

The grafting of vinyl polymers onto the surface of polymethylsiloxane-coated titanium dioxide modified with alcoholic hydroxyl groups (Ti/Si–R–OH) were investigated. The introduction of azo and trichloroacetyl groups onto the surface of Ti/Si–R–OH was achieved by the reaction of the surface alcoholic hydroxyl groups with 4,4′-azobis(4-cyanopentanoic acid) and trichloroacetyl isocyanate, respectively. The radical polymerizations of vinyl monomers were successfully initiated by the azo groups introduced onto the surface and by the system consisting of Mo(CO)₆ and Ti/Si–R–COCCl₃. During the polymerization, the corresponding polymers were effectively grafted onto the titanium dioxide surface through propagation from surface radicals formed by the decomposition of azo groups and by the reaction of Mo(CO)₆ with trichloroacetyl groups on the surface. The percentage of grafting and grafting efficiency in the graft polymerization initiated by the system consisting of Ti/Si–R–COCCl₃ and Mo(CO)₆ were much larger than those initiated by azo groups. The polymer-grafted titanium dioxide was found to produce a stable colloidal dispersion in good solvents for the grafted polymer. The dispersibility of poly(N,N-diethylacrylamide)-grafted titanium dioxide in water was controlled by temperature. In addition, the wettability of the surface of titanium dioxide to water was readily controlled by grafting of hydrophilic or hydrophobic polymers.     

Functional biohybrid materials synthesized via surface-initiated MADIX/RAFT polymerization from renewable natural wood fiber: Grafting of polymer as non leaching preservative

Crude wood fibers represent a wide class of renewable resources. The surface modification of such materials via covalent grafting of polymer offers new surface properties with non-leaching coating. The grafting of the polymer chains was achieved by surface-initiated controlled radical polymerization through a grafted xanthate chain transfer agent. Macromolecular design via interchange of xanthate (MADIX) technique was chosen to graft poly(vinyl acetate), polystyrene, poly(n-butyl acrylate) and poly(4-vinylbenzyl chloride)-polystyrene amphiphilic cationic copolymers. Water contact angle measurements highlighted the hydrophobization of the wood fiber surface with a nanoscaled polymer monolayer indicating the appropriate coverage of the fiber. X-ray photoelectron spectroscopy showed the successful grafting of the polymer after drastic washing procedure. The quaternization of the grafted polystyrene-co-poly(4-vinyl benzyl chloride) copolymers with tertiary amine allows the introduction of biocide quaternary ammonium functions while preserving the hydrophobic character of the modified wood fiber when introducing a long alkyl chain in the statistical copolymer. Finally, the cationic copolymer was subjected to Coniophora Puteana to evaluate its propensity to limit the fungi expansion.     

Radical polymerization of vinyl monomers in the presence of carbon black initiated by 2,2'‐azobisisobutyronitrile and benzoyl peroxide in ionic liquid

The radical polymerization behavior of vinyl monomers, such as styrene, methyl methacrylate (MMA), and vinyl acetate (VAc), in the presence of carbon black initiated by benzoyl peroxide (BPO) and 2,2'‐azobisisobutyronitrile (AIBN) in ionic liquid (IL) was compared with those in toluene. 1‐Butyl‐3‐methylimidazolium hexafluorophosphate was used as IL. The radical polymerization of vinyl monomers initiated by BPO and AIBN in the presence of carbon black was remarkably retarded in toluene. On the contrary, the retardation of the polymerization by carbon black was considerably reduced in IL. During the radical polymerization in the presence of carbon black, a part of polymer formed was grafted onto carbon black surface based on the termination reaction of the growing polymer radicals with carbon black surface. The percentage of grafting and molecular weight of polymer in IL were much higher than those in toluene. This may be due to the fact that lifetime of the growing polymer radical is prolonged because of high viscosity of IL. Therefore, the growing polymer radicals with higher molecular weight were trapped by carbon black surface, because of stabilization of polymer radicals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

炭黑表面接枝聚合改性进展

从炭黑粒子表面性质及表面化学基团出发 ,并结合聚合反应理论 ,介绍了将单体接枝聚合或将聚合物直接接枝到炭黑表面的自由基接枝、正离子接枝、负离子接枝及其他功能化接枝改性方法。论述了实现这些过程的溶液法、熔融法及辐射法接枝等工艺方法及影响炭黑接枝改性的因素。炭黑表面接枝聚合改性能大大扩大炭黑的应用范围。     

纳米无机氧化物粒子表面接枝改性

本文对纳米无机氧化物粒子表面的接枝改性作了论述,重点介绍了纳米粒子表面官能团引发的接枝聚合(自由基聚合、阴离子集合、阳离子聚合),并对各种接枝方法以及其发展情况进行了评价。同时对树状接枝进行了简要的介绍。     

一种新型阳离子聚丙烯酰胺的合成及表征

将具有球型分子结构的超支化聚合物接枝到阳离子聚丙烯酰胺上,目的是当用阳离子聚丙烯酰胺处理油田污水时,抑制分子的卷曲速度,提高絮凝性能。作者首先以二甲基二烯丙基氯化铵(DMDAAC)、丙烯酰胺(AM)和丙烯酸(AA)为单体,聚合得阳离子聚丙烯酰胺,该聚合物具有线型分子结构。再以甲基丙烯酰氧乙基三甲基氯化铵(DMC)与端部氨基的超支化聚合物反应,得到端部带有阳离子的超支化聚合物,该聚合物具有类似球型的分子结构。然后将阳离子超支化聚合物接枝到线形阳离子聚丙烯酰胺上,得到一种接枝改性的阳离子聚丙烯酰胺。用红外分光光度仪分析证明得到了预期的产物结构,并测定了产物的特性粘度、阳离子度。     

马来酸酐在炭黑表面接枝聚合的研究

研究了过氧化苯甲酰引发马来酸酐在炭黑表面的接枝聚合反应，探讨了反应时间、引发剂用量、接枝单体用量对接枝率的影响。结果表明，接枝率随反应时间的延长而增加，但２ｈ后，接枝率增加不多；随引发剂用量的增加，接枝率呈上升趋势，但用量在１５ｍｇ以后，接枝率趋于定值；随接枝单体用量的增加，接枝率直线上升。在本实验条件下，接枝率达到９％。通过接枝产物的Ｘ射线光电子能谱及红外分析可以证实，马来酸酐已接枝到炭黑表面。从光学显微图像分析结果可知，马来酸酐接枝改性对炭黑在聚合物基体中的分布和分散性能起到良好的改善作用。     

Preparation of amphiphilic carbon black by postgrafting of polyethyleneimine to grafted polymer chains on the surface

Summary To prepare amphiphilic carbon black, we investigated the postgrafting reaction of polyethyleneimine (PEI) with pendant glycidyl groups of grafted polymer on carbon black surface. The grafting of polymers having pendant glycidyl groups onto carbon black surface was achieved by the copolymerization of glycidyl methacrylate (GMA) with methyl methacrylate (MMA) initiated by azo groups introduced onto the surface. Pendant glycidyl groups of poly(GMA-co-MMA)-grafted carbon black was found to react with PEI, and the corresponding polymers postgrafted to the grafted copolymer chains on carbon black surface: the percentage of PEI-postgrafting was readily controlled by the reaction conditions. PEI-postgrafted to poly(GMA-co-MMA)-grafted carbon black, whose PEI postgrafting is 3.9% showed amphiphilic nature and acted as an emulsifier. Received: 13 April 1998/Revised version: 20 May 1998/Accepted: 22 May 1998     

Reactive carbon black having acyl imidazole or acid anhydride groups: Preparation and reaction with functional polymers having hydroxyl or amino groups

The introduction of acyl imidazole groups onto a carbon black surface was achieved by the reaction of the carboxyl groups on the surface with N N′-carbonyldiimidazole, the loading of acyl imidazole groups introduced was determined to be 0.28 mmol/g. In addition, reactive carbon black having acid anhydride groups was prepared by the reaction of phenolic hydroxyl groups with trimellitic anhydride chloride; the amount of acid anhydride groups introduced onto the surface was determined to be 0.20 mmol/g. The reaction of acyl imidazole groups on carbon black with commercially available polymers having hydroxyl or amino groups such resulted in polymers that were found to be grafted onto the surface via ester or amide bonds. The percentage of grafting of diol-type poly(propylene glycol) and diamine-type polydimethylsiloxane was increased to 27.2 % and 42.5 %, respectively. Furthermore, acid anhydride groups on carbon black also reacted with functional polymers having hydroxyl or amino groups to give polymer-grafted carbon blacks. The grafting reaction was accelerated by the addition of tertiary amines. These polymer-grafted carbon blacks produced a stable colloidal dispersion in good solvents for the grafted polymer, but readily precipitated in poor solvents.