TAP study of NOx storage and reduction on Pt/Al2O3 and Pt/Ba/Al2O3

A systematic mechanistic study of NO storage and reduction over Pt/Al₂O₃ and Pt/BaO/Al₂O₃ is carried out using Temporal Analysis of Products (TAP). NO pulse and NO/H₂ pump-probe experiments at 350 °C on pre-reduced, pre-oxidized, and pre-nitrated catalysts reveal the complex interplay between storage and reduction chemistries and the importance of the Pt/Ba coupling. NO pulsing experiments on both catalysts show that NO decomposes to major product N₂ on clean Pt but the rate declines as oxygen accumulates on the Pt. The storage of NO over Pt/BaO/Al₂O₃ is an order of magnitude higher than on Pt/Al₂O₃ showing participation of Ba in the storage even in the absence of gas phase O₂. Either oxygen spillover or transient NO oxidation to NO₂ is postulated as the first steps for NO storage on Pt/BaO/Al₂O₃. The storage on Pt/Ba/Al₂O₃ commences as soon as Pt–O species are formed. Post-storage H₂ reduction provides evidence that a fraction of NO is not stored in close proximity to Pt and is more difficult to reduce. A closely coupled Pt/Ba interfacial process is corroborated by NO/H₂ pump-probe experiments. NO conversion to N₂ by decomposition is sustained on clean Pt using excess H₂ pump-probe feeds. With excess NO pump-probe feeds NO is converted to N₂ and N₂O via the sequence of barium nitrate and NO decomposition. Pump-probe experiments with pre-oxidized or pre-nitrated catalyst show that N₂ production occurs by the decomposition of NO supplied in a NO pulse or from the decomposition of NOx stored on the Ba. The transient evolution of the two pathways depends on the extent of pre-nitration and the NO/H₂ feed ratio.     

Pt-Ba/alumina NOx storage-reduction catalysts: Influence of Ba loading on NOx storage behavior

The NO_x storage behavior of a series of Pt-Ba/Al₂O₃ catalysts, prepared by wet impregnation of Pt/Al₂O₃ with Ba(Ac)₂, has been investigated. The catalysts with Ba loadings in the range 4.5–28 wt.% were calcined at 500 °C in air and subsequently exposed to NO pulses in 5 vol.% O₂/He atmosphere. Catalysts were characterized by means of thermogravimetry (TG) combined with mass spectroscopy (MS) and XRD before and after exposure to NO pulses. Characterization of the calcined catalysts corroborated the existence of three Ba-containing phases which are discernible based on their different thermal stability: BaO, LT-BaCO₃ and HT-BaCO₃. Characterization after NO_x exposure showed that the different Ba-containing phases present in the catalysts possess different reactivity for barium nitrate formation, depending on their interfacial contact. The different Ba(NO₃)₂ species produced upon NO_x exposure could be distinguished based on their thermal stability. The study revealed that during the NO_x storage process a new thermally instable BaCO₃ phase formed by reaction of evolved CO₂ with active BaO. The fraction of Ba-containing species that were active in NO_x storage depended on the Ba loading, showing a maximum at a Ba loading of about 17 wt.%. Lower and higher Ba loading resulted in a significant loss of the overall efficiency of the Ba-containing species in the storage process. The loss in efficiency observed at higher loading is attributed to the lower reactivity of the HT-BaCO₃, which becomes dominant at higher loading, and the increased mass transfer resistance.     

Experimental and microkinetic modeling of steady-state NO reduction by H2 on Pt/BaO/Al2O3 monolith catalysts

Experimental results describing the product distribution during the reduction of NO by H₂ on Pt/Al₂O₃ and Pt/BaO/Al₂O₃ catalysts are presented in the temperature range 30–500 °C and H₂/NO feed ratio range of 0.9–2.5. A microkinetic model that describes the kinetics of NO reduction by H₂ on Pt/Al₂O₃ is proposed and most of the kinetic parameters are estimated from either literature data or from thermodynamic constraints. The microkinetic model is combined with the short monolith flow model to simulate the conversions and selectivities corresponding to the experimental conditions. The predicted trends are in excellent qualitative and reasonable quantitative agreement with the experimental results. Both the model and the experiments show that N₂O formation is favored at low temperatures and low H₂/NO feed ratios, N₂ selectivity increases monotonically with temperature for H₂/NO feed ratios of 1.2 or less but goes through a maximum at intermediate temperatures (around 100 °C) for H₂/NO feed ratios 1.5 or higher. Ammonia formation is favored for H₂/NO feed ratios of 1.5 or higher and intermediate temperatures (100–350 °C) buts starts to decompose at a temperature of 400 °C or higher. The microkinetic model is used to determine the surface coverages and explain the trends in the experimentally observed selectivities.     

Al18B4O33 aluminium borate: A new efficient support for palladium in the high temperature catalytic combustion of methane

Well crystallised aluminium borate Al₁₈B₄O₃₃ has been synthesised from alumina and boric acid with a BET area of 18 m²/g after calcination at 1100 °C. Afterwards, 2 wt.% Pd/Al₁₈B₄O₃₃ was prepared by conventional impregnation of Pd(NO₃)₂ aqueous solution and calcination in air at 500 °C. The catalytic activity of Pd/Al₁₈B₄O₃₃ in the complete oxidation of methane was measured between 300 and 900 °C and compared with that of Pd/Al₂O₃. Pd/Al₁₈B₄O₃₃ exhibited a much lower activity than Pd/Al₂O₃ when treated in hydrogen at 500 °C or aged in O₂/H₂O (90:10) at 800 °C prior to catalytic testing. Surprisingly, a catalytic reaction run up to 900 °C in the reaction mixture induced a steep increase of the catalytic activity of Pd/Al₁₈B₄O₃₃ which became as active as Pd/Al₂O₃. Moreover, the decrease of the catalytic activity observed around 750 °C for Pd/Al₂O₃ and attributed to PdO decomposition into metallic Pd was significantly shifted to higher temperatures (820 °C) in the case of Pd/Al₁₈B₄O₃₃. The existence of two distinct types of PdO species formed on Al₁₈B₄O₃₃ and being, respectively, responsible for the improvement of the activity at low and high temperature was proposed on the basis of diffuse reflectance spectroscopy and temperature-programmed desorption of O₂.     

Water-induced bulk Ba(NO3)2 formation from NO2 exposed thermally aged BaO/Al2O3

Phase changes in high temperature treated (>900 °C) 8 or 20 wt% BaO supported on γ-Al₂O₃ model lean NO_x trap (LNT) catalysts, induced by NO₂ and/or H₂O adsorption, were investigated with powder X-ray diffraction (XRD), solid state ²⁷Al magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy, and NO₂ temperature programmed desorption (TPD) experiments. After calcination in dry air at 1000 °C, the XRD and solid state ²⁷Al MAS NMR results confirm that stable surface BaO and bulk BaAl₂O₄ phases are formed for 8 and 20 wt% BaO/Al₂O₃, respectively. Following NO₂ adsorption over these thermally treated samples, some evidence for nanosized Ba(NO₃)₂ particles are observed in the XRD results, although this may represent a minority phase. However, when water was added to the thermally aged samples after NO₂ exposure, the formation of bulk crystalline Ba(NO₃)₂ particles was observed in both samples. Solid state ²⁷Al MAS NMR is shown to be a good technique for identifying the various Al species present in the materials during the processes studied here. NO₂ TPD results demonstrate a significant loss of uptake for the 20 wt% model catalysts upon thermal treatment. However, the described phase transformations upon subsequent water treatment gave rise to the partial recovery of NO_x uptake, demonstrating that such a water treatment of thermally aged catalysts can provide a potential method to regenerate LNT materials.     

Reactor and in situ FTIR studies of Pt/BaO/Al2O3 and Pd/BaO/Al2O3 NOx storage and reduction (NSR) catalysts

The reduction of NO under cyclic “lean”/“rich” conditions was examined over two model 1 wt.% Pt/20 wt.% BaO/Al₂O₃ and 1 wt.% Pd/20 wt.% BaO/Al₂O₃ NO_x storage reduction (NSR) catalysts. At temperatures between 250 and 350 °C, the Pd/BaO/Al₂O₃ catalyst exhibits higher overall NO_x reduction activity. Limited amounts of N₂O were formed over both catalysts. Identical cyclic studies conducted with non-BaO-containing 1 wt.% Pt/Al₂O₃ and Pd/Al₂O₃ catalysts demonstrate that under these conditions Pd exhibits a higher activity for the oxidation of both propylene and NO. Furthermore, in situ FTIR studies conducted under identical conditions suggest the formation of higher amounts of surface nitrite species on Pd/BaO/Al₂O₃. The IR results indicate that this species is substantially more active towards reaction with propylene. Moreover, its formation and reduction appear to represent the main pathway for the storage and reduction of NO under the conditions examined. Consequently, the higher activity of Pd can be attributed to its higher oxidation activity, leading both to a higher storage capacity (i.e., higher concentration of surface nitrites under “lean” conditions) and a higher reduction activity (i.e., higher concentration of partially oxidized active propylene species under “rich” conditions). The performance of Pt and Pd is nearly identical at temperatures above 375 °C.     

The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

On the dynamic behavior of “NOx-storage/reduction” Pt–Ba/Al2O3 catalyst

The NO_x storage and reduction functions of a Pt–Ba/Al₂O₃ “NO_x storage–reduction” catalyst has been investigated in the present work by applying the transient response and the temperature programmed reaction methods, by using propylene as the reducing agent. It is found that: (i) the storage of NO_x occurs first at BaO and then at BaCO₃, which are the most abundant sites following regeneration of catalyst with propylene; (ii) the overall storage process at BaCO₃ is slower than at BaO; (iii) CO₂ inhibits the NO_x storage at low temperatures; (iv) the amount of NO_x stored up to catalyst saturation at 350 °C corresponds to 17.6% of Ba; (v) the reduction of stored NO_x groups is fast and is limited by the concentration of propylene in the investigated T range (250–400 °C); (vi) selectivity to N₂ is almost complete at 400 °C but is significantly lower at 300 °C due to the formation of NO which can be tentatively ascribed to the presence of unselective Pt–O species.     

Influence of the pre-treatment on the structure and reactivity of Ir/γ-Al2O3 catalysts in the selective reduction of nitric oxide by propene

The selective catalytic reduction (SCR) of nitric oxide by propene over Ir/Al₂O₃ under lean-burn conditions (1000 vpm NO, 2000 vpm C₃H₆, 500 vpm CO, 10 vol.% O₂) was studied. The activity was shown to be strongly enhanced after exposure of the catalyst at 600°C under the reaction mixture, irrespective of the oxidising or reducing pre-treatment. Simultaneously, the Ir dispersion decreased from 78 to 10%. The influence of each component of the reaction mixture on the activation process was examined. The presence of both CO and O₂ was found to be necessary to activate Ir/Al₂O₃ while NO would not be. In situ FT-IR results revealed that initially fully oxidised Ir particles partially reduced in the feed to form Ir⁰ reduced surface sites (νCO at 2060 cm⁻¹) which adsorbed CO up to 350–400°C. The activation under reactants was related to the formation of these sites. The presence of reduced (or partially reduced) Ir sites, possibly siting at the surface of IrO₂ particles and stabilised by CO adsorption, was proposed to be responsible for the SCR activity.     

Pt-Ba/alumina NOx storage-reduction catalysts: Effect of Ba-loading on build-up, stability and reactivity of Ba-containing phases

A series of Pt-Ba/Al₂O₃ catalysts with Ba-loadings in the range 4.5–28 wt.% has been prepared by wet impregnation of Pt/Al₂O₃ with barium acetate (Ba(Ac)₂) as Ba precursor. The build-up and thermal stability of the deposited Ba-containing species was followed by means of XRD and thermogravimetry (TG) combined with mass spectroscopy (MS). Samples were characterized before and after thermal treatment (calcination). The study showed that the thermal stability of the Ba-containing phases depends on their interaction with the alumina support and the presence of dispersed platinum. In calcined catalysts, three different Ba-containing species could be distinguished based on their crystallinity and thermal stability. The relative concentration of these species varied with the Ba-loading. The first layer of Ba-containing species, corresponding to saturation of the alumina surface with Ba(Ac)₂, contained up to 12.5 wt.% of Ba in the form of amorphous BaO. Increasing the Ba-loading further resulted in 5–6 wt.% of Ba in the form of amorphous carbonates with relatively low thermal stability (LT-BaCO₃). At Ba-loadings higher than about 16 wt.%, crystalline barium carbonate became discernible which exhibited remarkably higher thermal stability (HT-BaCO₃). NO_x storage tests accomplished by exposing the catalysts to pulses of NO in oxygen containing carrier gas at 300 °C indicated that from all characterized Ba-containing phases, LT-BaCO₃ possesses the highest reactivity for NO_x storage, i.e. LT-BaCO₃ is transformed most rapidly to Ba(NO₃)₂.     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

Formation and stability of barium aluminate and cerate in NOx storage-reduction catalysts

The formation and stability of BaAl₂O₄ and BaCeO₃ in Pt-Ba/Al₂O₃ and Pt-Ba/CeO₂ based NO_x storage-reduction (NSR) catalysts has been investigated using kinetic measurements, X-ray diffraction, thermal analysis and X-ray absorption spectroscopy. In as-prepared state, the Ba-component in the NSR catalysts was made up of amorphous BaO and BaCO₃. The formation of BaAl₂O₄ started above 850 °C, whereas the formation of BaCeO₃ was already observed at 800 °C and was faster than that of BaAl₂O₄. The stability of BaAl₂O₄ and BaCeO₃ in various liquid and gaseous atmospheres was different. BaAl₂O₄ was rapidly hydrated at room temperature in the presence of water and transformed to Ba(NO₃)₂ and γ-alumina in the presence of HNO₃, whereas BaCeO₃ was decomposed to much lower extent under these conditions. Interestingly, BaCeO₃ was transformed to Ba(NO₃)₂/CeO₂ in the presence of NO₂/H₂O at 300–500 °C. Also, the presence of CO₂ led to decomposition of barium cerate, which has important consequences for the catalyst ageing under NO_x-storage conditions and can be exploited for regeneration of thermally aged NSR-catalysts.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

Mean field modelling of NOx storage on Pt/BaO/Al2O3

A mean field model, for storage and desorption of NO_x in a Pt/BaO/Al₂O₃ catalyst is developed using data from flow reactor experiments. This relatively complex system is divided into five smaller sub-systems and the model is divided into the following steps: (i) NO oxidation on Pt/Al₂O₃; (ii) NO oxidation on Pt/BaO/Al₂O₃; (iii) NO_x storage on BaO/Al₂O₃; (iv) NO_x storage on Pt/BaO/Al₂O₃ with thermal regeneration and (v) NO_x storage on Pt/BaO/Al₂O₃ with regeneration using C₃H₆. In this paper, we focus on the last sub-system. The kinetic model for NO_x storage on Pt/BaO/Al₂O₃ was constructed with kinetic parameters obtained from the NO oxidation model together with a NO_x storage model on BaO/Al₂O₃. This model was not sufficient to describe the NO_x storage experiments for the Pt/BaO/Al₂O₃, because the NO_x desorption in TPD experiments was larger for Pt/BaO/Al₂O₃, compared to BaO/Al₂O₃. The model was therefore modified by adding a reversible spill-over step. Further, the model was validated with additional experiments, which showed that NO significantly promoted desorption of NO_x from Pt/BaO/Al₂O₃. To this NO_x storage model, additional steps were added to describe the reduction by hydrocarbon in experiments with NO₂ and C₃H₆. The main reactions for continuous reduction of NO_x occurs on Pt by reactions between hydrocarbon species and NO in the model. The model is also able to describe the reduction phase, the storage and NO breakthrough peaks, observed in experiments.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

A new NOx storage-reduction electrochemical catalyst

A new NO_x storage-reduction electrochemical catalyst has been prepared from a polycrystalline Pt film deposited on 8 mol% Y₂O₃-stabilized ZrO₂ (YSZ) solid electrolyte. BaO has been added onto the Pt film by impregnation method. The NO_x storage capacity of Pt-BaO/YSZ system was investigated at 350 °C and 400 °C under lean conditions. Results have shown that the electrochemical catalyst was effective for NO_x storage. When nitric oxides are fully stored, the catalyst potential is high and reaches its maximum. On the other hand, when a part of NO and also NO₂ desorb to the gas phase, the catalyst potential remarkably drops and finally stabilizes when no more NO_x storage occurs but only the reaction of NO oxidation into NO₂. Furthermore, the investigation has clearly demonstrated that the catalyst potential variation versus temperature or chemical composition is an effective indicator for in situ following the NO_x storage-reduction process, i.e. the storage as well as the regeneration phase. The catalyst potential variations during NO_x storage process was explained in terms of oxygen coverage modifications on the Pt.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Comparison of the activity of Ru and Pt catalysts for the oxidation of carbon by NO2

The role of two catalysts Pt/Al₂O₃ and Ru/NaY on the oxidation of carbon by NO₂ was investigated in the temperature range 300–400 °C. In the case of Pt/Al₂O₃ no significant catalytic effect on the carbon oxidation rate is observed although decomposition of NO₂ takes place on the noble metal and leads to the formation of NO. This result suggests that the amount of the oxygen atoms transferred from the metallic surface sites to the carbon surface to form C(O) complex is negligible. In contrast, in presence of Ru/NaY the oxidation rate of carbon by NO₂ is markedly increased. Hence, a significant part of the formed O through catalytic decomposition of NO₂ on Ru surface sites is transferred to the carbon surface leading to a larger amount of C(O) complexes on the carbon surface. Thus, the ruthenium surface is a generator of active oxygen species that are spilled over on the carbon surface at 350 °C.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.