Nucleophilic Displacement Polymerlzation of N,N'-BIS(p-Chlorobenzylidine)-4, 4'-Diaminodiphenyl Ether with Sodium Sulfide

A novel poly(Schiff-base sulfide) polymer was synthesized by nucle-ophilic displacement polymerization of N,N'-bis(p-chlorobenzylidine)-4, 4'-diaminodiphenyl ether with sodium sulfide in anhydrous condition. The resulting polymer was soluble in some aprotic solvents having inherent viscosity of 0.18 dL/g in dimethylacetamide at 30°C. The monomer and the polymer were characterized by elemental analysis, infrared, and ¹H NMR (nuclear magnetic resonance) spectroscopy. The thermal characteristics of the polymer were also studied by thermo-gravimetric analysis and differential scanning calorimetry. The temperature of 10% weight loss, glass transition temperature (T _g). and crystalline melting point (T _m) of the polymer were found to be 420, 91.89, and 38575°C respectively.     

Renewable Aliphatic Polyesters from Fatty Dienes by Acyclic Diene Metathesis Polycondensation

Three renewable, linear, aliphatic polyesters were prepared by Acyclic diene metathesis (ADMET) polymerization of α,ω-dienes derived from fatty acids. Condensation of 9-decenoic acid with allyl 9-decenoate, ethylene glycol, and 9-decen-1-ol proceeded in high conversion (≥94%) and purity (>99%) to give α,ω-dienes suitable for subsequent polycondensation. Polymerization was achieved using 1.0 mol% Hoveyda-Grubbs second-generation metathesis catalyst in combination with 2.0 mol% 2,6-dichloro-1,4-benzoquinone as an isomerization inhibitor under vacuum to drive equilibria toward polymer formation via ethene removal. Polymerization in the presence of solvent promoted ring-closing metathesis (RCM) at the expense of polymer, with cyclization increasing as the concentration of monomer decreased. Thus, ADMET polymerizations were performed in bulk to mitigate RCM. The resulting polymers with M _n and Ð that ranged from 6.6 to 8.9 kDa and 1.75–2.14, respectively, contained 76% or more of renewable carbon content and exhibited atom and carbon economies of greater than 84%. Melt (T _m) and crystallization (T _c) temperatures were 20.8–48.4 °C and 3.8–37.6 °C, respectively, and increased as ester density decreased within polymer structures. Sub-ambient glass transitions ranged from −10.3 to −50.0 °C. Lastly, the polymers were thermally stable below 320 °C, as 10% mass loss (T₁₀) occurred above 340 °C, which indicated that they existed as liquids for at least 319 °C (T₁₀ − T _m) before decomposing.     

Synthesis and evaluation of the thermal properties of biosourced poly(ether)ureas and copoly(ether)ureas from 1,4:3,6‐dianhydrohexitols

A new series of poly(ether)ureas were prepared by solution polyaddition of three diamines based on 1,4:3,6‐dianhydrohexitols with three types of diisocyanate. The corresponding poly(ether)ureas were obtained with high yields. They were characterized by various analytical techniques (NMR, TGA and differential thermal analysis, DSC). NMR spectroscopy allowed us to confirm structure type and to optimize reaction conditions and DSC proved the high thermal properties of the products obtained (T_g and T_m in the range 126 ? 158 °C and 235 ? 330 °C respectively). Then, copoly(ether)ureas partially based on commercial diamines were synthesized in order to reduce polymer cost and tune their thermal behaviour. The reactivity of both diamines was evaluated by their incorporation in the polymer by means of NMR spectra. Then their thermal properties were compared with fully commercial diamine based polyureas by DSC studies. © 2014 Society of Chemical Industry     

Pure and complex nanostructures using poly[bis(triiso‐propylsilylethynyl) benzodithiophene‐bis(decyltetradecyl‐thien) naphthobisthiadiazole], carbon nanotubes and reduced graphene oxide for high‐performance polymer solar cells

Crystallization of poly[bis(triiso‐propylsilylethynyl) benzodithiophene‐bis(decyltetradecyl‐thien) naphthobisthiadiazole] (PBDT‐TIPS‐DTNT‐DT) was investigated in supramolecules based on carbon nanotubes (CNTs) and reduced graphene oxide (rGO) and their grafted derivatives. The principal peaks of PBDT‐TIPS‐DTNT‐DT crystals were in the range 3.50°–3.75°. By grafting the surface of the carbonic materials, the assembling of polymer chains decreased because of hindrance of poly(3‐dodecylthiophene) (PDDT) grafts against π‐stacking. The diameters of CNT/polymer and CNT‐g‐PDDT/polymer supramolecules were 160 and 100 nm. The rGO/polymer supramolecules had the highest melting point (T_m = 282 °C) and fusion enthalpy (ΔH_m = 25.98 J g^?1), reflecting the largest crystallites and the most ordered constituents. Nano‐hybrids based on grafted rGO (276 °C and 28.26 J g^?1), CNT (275 °C and 27.32 J g^?1) and grafted CNT (268 °C and 22.17 J g^?1) were also analyzed. T_m and ΔH_m values were significantly less in corresponding melt‐grown systems. The nanostructures were incorporated in active layers of PBDT‐TIPS‐DTNT‐DT:phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) solar cells to improve the photovoltaic features. The best results were detected for PBDT‐TIPS‐DTNT‐DT:PC₇₁BM:rGO/polymer systems having J_sc = 13.11 mA cm^?2, fill factor 60% and V_oc = 0.71 V with an efficacy of 5.58%. On grafting the rGO and CNT, efficiency reductions were 12.01% (5.58%–4.91%) and 9.34% (4.07%–3.69%), respectively. © 2019 Society of Chemical Industry     

Intrinsic viscosity–molecular weight relationship for low molecular weight nylon 6

Samples of nylon 6 have been prepared by the hexamethylene diamine-initiated polymerization of ?-caprolactam at 220°C. Fractionation of these with m-cresol–diethyl ether at 26°C yielded 15 amino-terminated fractions of M?_n of 337–10,940 determined conductometrically. Below M?_n = 4,306 the Mark-Houwink parameters in m-cresol at 30°C are K = 3.0 × 10^?3 dl/g and v = 0.53 ± 0.02. Thereafter v exhibits a pronounced increase. The value of K is similar to the values of Kθ derived from Stockmayer-Fixman plots of published data in good solvents. The findings thus corroborate a current hypothesis that fractionated, low molecular weight polymers in good solvents tend to behave viscometrically, as if they were under θ conditions (i.e., K = K_θ and v = 0.50).     

Characterization of sulfur-cured styrene–butadiene copolymer rubbers and their polybutadiene blends

Dissolution of sulfur-cured, carbon black-loaded copolymers and their blends with cis-1,4-polybutadiene (PBD) are brought about by boiling with o-dichlorobenzene which contains a small amount of 2,2′-dibenzamidodiphenyl disulfide. The resulting slurries are subjected to a sequence of separations which include high-speed centrifugation to remove solids, and solvent precipitation followed by filtration to isolate the precipitates. The precipitates are washed with solvent to remove soluble organic materials followed by carbon disulfide washing to dissolve the polymers. Cast films of the polymers are obtained by evaporating the carbon disulfide washings onto sodium chloride discs. The infrared spectra of the cast films of these preparations are very similar to those of their respective polymers prior to loading and curing. Calculations for relative concentrations of bound styrene and PBD microstructures permit nominal identification of the kinds of styrene–butadiene rubber and the amounts of cis-1,4-PBD used in a cured rubber formulation. Absorption bands used are near 3.35 μ for cis-1,4-PBD, 6.65μ for bound styrene, 10.35 μ for trans-1,4-PBD; and 11.0 μ for vinyl-1,2-PBD. Efforts are being made to improve the data by using a grafting infrared instrument and also to extend the calibrations to include other rubber blends.     

Synthesis of novel polyimide with highly enhanced thermal stability of second harmonic generation for electro-optic applications

2,3-Bis-(3,4-dicarboxyphenylcarboxyethoxy)-1-(2,2-dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 1,4-phenylenediamine to yield novel Y-type polyimide 5 containing 2,3-dioxybenzylidenemalononitrile group as NLO-chromophores, which constitute parts of the polymer backbones. The resulting polyimide 5 was soluble in polar solvents such as acetone and N,N-dimethylformamide. Polymer 5 showed a thermal stability up to 330 °C in thermogravimetric analysis thermogram with T _g value obtained from differential scanning calorimetry thermogram near 190 °C. The second harmonic generation (SHG) coefficient (d ₃₃) of poled polymer films at the 1064 nm fundamental wavelength was around 3.15×10^-9 esu. The dipole alignment exhibited a thermal stability even at 20 °C higher than the glass-transition temperature, and there was no SHG decay below 210 °C because of the partial main chain character of polymer structure, which was acceptable for nonlinear optical device applications.     

Poly(L‐lactide): v. effects of storage in swelling solvents on physical properties and structure of poly(L‐lactide)

The effects of storage at 25°C in swelling solvents having different solubility parameter (δ_s) values of 16.8–26.0 J^0.5 cm^−1.5 on the physical properties and structure of as‐cast poly(L ‐lactide) (PLLA) films was investigated by the degree of swelling (DS), differential scanning calorimetry (DSC), and tensile tests. It was found that PLLA film shows durabity to swelling solvents having δ_s values much lower or higher than the value range of 19–20.5 J^0.5 cm^−1.5 and that the polymer solubility parameter (δ_p) for PLLA is in the value range of 19–20.5 J^0.5 cm^−1.5. The decrease in the glass transition temperature (T_g) and tensile properties and the increase in melting temperature (T_m) and crystallinity (x_c) were larger for PLLA films swollen in solvents having a high DS at 7 days (DS_7days). The slight increase in T_m and x_c for PLLA films after swelling in solvents with high DS_7days values was due to the crystallization of PLLA that occurred during swelling, while the small increase in T_g and elongation at break (ε_B) for PLLA films after immersion in the solvents having low DS_7days values was ascribed to stabilized chain packing in the amorphous region. The T_g, ε_B, and Young's modulus of the PLLA films after swelling in the solvents varied in the ranges of 47–57°C, 4–8%, and 55–77 kg/mm², depending on their DS_7days or δ_s values. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1582–1589, 2001     

Effect of Polar Organic Solvents on Self‐Aggregation of Some Cationic Monomeric and Dimeric Surfactants

Surface and micellization behavior of some cationic monomeric surfactants, viz., cetyldiethylethanolammonium bromide (CDEEAB), cetyldimethylethanolammonium bromide (CDMEAB), tetradecyldiethylethanolammonium bromide (TDEEAB) and dimeric surfactants, i.e., alkanediyl‐α, ω‐bis(dimethylhexadecylammonium bromide) (C₁₆‐s‐C₁₆, 2Br^? where s = 4, 12), butanediyl‐1,4‐bis(dimethyldodecylammonium bromide (C₁₂‐4‐C₁₂, 2Br^?) and 2‐butanol‐1,4‐bis(dimethyldodecylammonium bromide) (C₁₂‐4(OH)‐C₁₂, 2Br^?), was studied in water‐organic solvents [10 and 20 % v/v ethylene glycol (EG) and diethylene glycol (DEG)] by conductivity, surface tension and steady‐state fluorescence methods at 300 K. The main focus of the present work is on the study of the effect of organic solvents on the critical micelle concentration (CMC), Gibbs free energy of micellization (ΔG°_m), Gibbs free energy of transfer (ΔG°_trans), Gibbs adsorption energy (ΔG°_ads) and some interfacial parameters such as the surface excess concentration (Γ_max), minimum area per surfactant molecule (A_min) and surface pressure (π_CMC). The aggregation number (N_agg) and Stern‐Volmer quenching constant (K_SV) were also determined by the steady‐state fluorescence method. It was observed that N_agg decreased with increasing volume percent of organic solvent. The results exhibited an increase in CMC in water‐organic solvents as compared to the respective surfactants in pure water. The negative values of ΔG°_m and ΔG°_ads indicate a spontaneous micellization process. The thermodynamics of micellization revealed that the micellization‐reducing efficiency of glycols increases with the concentration and the number of ethereal oxygens in the glycol.     

Characterization of block copolymers based on poly[3,3-bis(ethoxymethyl)oxetane] and other novel polyethers

Diblock, triblock, and alternating block copolymers based on poly[3,3-bis(ethoxymethyl) oxetane] [poly(BEMO)] and a random copolymer center block poly(BMMO-co-THF) composed of poly[3,3-bis(methoxymethyl)oxetane] [poly(BMMO)], and poly(tetrahydrofuran) [poly(THF)] were synthesized and characterized with respect to molecular weight. Glass transition temperatures T_g and melting temperatures T_m were characterized via DSC, modulus–temperature, and dynamic mechanical spectroscopy (DMS). These polyethers had T_m between 70°C and 90°C, and T_g between ?55°C and ?30°C. The degree of crystallinity of poly(BEMO) was found to be 65% by X-ray powder diffraction. Tensile properties of the triblock copolymer, poly(BEMO-block-BMMO-co-THF-block-BEMO) were also studied. A yield point was found at 4.1 × 10⁷ dyn/cm² and 10% elongation and failure at 3.8 × 10⁷ dyn/cm² and 760 % elongation. Morphological features were examined by reflected light microscopy and the kinetics of crystallization were studied. Poly(BEMO) and its block copolymers were found to form spherulites of 2–10 μm in diameter. Crystallization was complete after 2–5 min.     

Elastomeric and mechanical properties of poly-m-carboranylenesiloxanes

A new high-temperature elastomer, SiB-2, has been investigated by stress relaxation, modulus-temperature, and volume--temperature techniques. SiB-2 was found to be more stable than a related elastomer, radiation-cured silicone rubber, having about twice as long as a chemical relaxation time at 250°C. Possible mechanisms to account for this increased stability are discussed. At low temperatures, T_g for SiB-2 was estimated at –34°C., which compares well with T_i = ?30°C. for this polymer. By comparison, SiB-3 has T_i = ?60°C., while phenyl-modified SiB-4 was found to have T_i = ?25°C. T_m for SiB-2 was estimated to be + 56°C.     

Synthesis and properties of novel copolymers of poly(ether ketone ether ketone ketone) and poly(ether ketone ketone ether ketone ketone) containing 1,4‐naphthylene moieties

A new monomer, 1,4‐bis(4‐phenoxybenzoyl)naphthalene (BPOBN), was conveniently synthesized via a simple synthetic procedure from readily available materials. A series of novel copolymers of poly(ether ketone ether ketone ketone) and poly(ether ketone ketone ether ketone ketone) containing 1,4‐naphthylene moieties were prepared by the Friedel‐Crafts acylation solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of BPOBN and 4,4′‐diphenoxybenzophenone (DPOBPN), over a wide range of BPOBN/DPOBPN molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone in 1,2‐dichloroethane. The copolymers with 10–40% BPOBN are semicrystalline and had remarkably increased T_gs over the conventional PEEK and PEKK due to the incorporation of 1,4‐naphthylene moieties in the main chains. The copolymers with 30–40 mol% BPOBN had not only high T_gs of 176–177°C, but also moderate T_ms of 332–338°C, which are suitable for the melt processing. These polymers had tensile strengths of 101.5–104.7 MPa, Young's moduli of 2.49–2.65 GPa, and elongations at break of 13.3–15.7% and exhibited high thermal stability and excellent resistance to organic solvents. POLYM. ENG. SCI., 56:566–572, 2016. © 2016 Society of Plastics Engineers     

Characterization of biodegradable polymers by inverse gas chromatography. II. Blends of amylopectin and poly(ε‐caprolactone)

Amylopectin (AP), a potato‐starch‐based polymer with a molecular weight of 6,000,000 g/mol, was blended with poly(ε‐caprolactone) (PCL) and characterized with inverse gas chromatography (IGC), differential scanning calorimetry (DSC), and X‐ray diffraction (XRD). Five different compositions of AP–PCL blends ranging from 0 to 100% AP were studied over a wide range of temperatures (80–260°C). Nineteen solutes (solvents) were injected onto five chromatographic columns containing the AP–PCL blends. These solutes probed the dispersive, dipole–dipole, and hydrogen‐bonding interactions, acid–base characteristics, wettability, and water uptake of the AP–PCL blends. Retention diagrams of these solutes in a temperature range of 80–260°C revealed two zones: crystalline and amorphous. The glass‐transition temperature (T_g) and melting temperature (T_m) of the blends were measured with these zones. The two zones were used to calculate the degree of crystallinity of pure AP and its blends below T_m, which ranged from 85% at 104°C to 0% at T_m. IGC complemented the DSC method for obtaining the T_g and T_m values of the pure AP and AP–PCL blends. These values were unexpectedly elevated for the blends over that of pure AP and ranged from 105 to 152°C for T_g and from 166 to 210°C for T_m. The T_m values agreed well with the XRD analysis data. This elevation in the T_g and T_m values may have been due to the change in the heat capacity at T_g and the dependence of T_g on various variables, including the molecular weight and the blend composition. Polymer blend/solvent interaction parameters were measured with a variety of solutes over a wide range of temperatures and determined the solubility of the blends in the solutes. We were also able to determine the blend compatibility over a wide range of temperatures and weight fractions. The polymer–polymer interaction coefficient and interaction energy parameter agreed well on the partial miscibility of the two polymers. The dispersive component of the surface energy of the AP–PCL blends was measured with alkanes and ranged from 16.09 mJ/m² for pure AP to 38.26 mJ/m² when AP was mixed with PCL in a 50/50% ratio. This revealed an increase in the surface energy of AP when PCL was added. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3076–3089, 2006     

Preparation and properties of graft and block copolymers of poly(p-phenylene terephthalamide) with polybutadiene

Graft copolymers of polybutadiene (PBD) onto poly(p-phenylene terephthalamide) (PPTA) were prepared by the nucleophilic substitution of N-metalated PPTA with telechelic PBD having bromide end groups. Block copolymers were synthesized by the condensation reaction of telechelic PBD having acid chloride end groups with amino-group-terminated PPTA. The structure of these copolymers was identified by IR spectra. Graft and block copolymers contained PBD segments up to 85 wt % and 45 wt %, respectively. Thermomechanical analyses (TMA) proved the existence of distinctive primary absorption peak corresponding with T_g of PBD for both graft and block copolymers. The T_g's of both types of the copolymers were further ascertained by the DSC curves. TMA curves suggested that the microphase separation occurred between PPTA and PBD. The incorporation of PPTA segments into PBD increased the decomposition temperature compared with the blend polymer composed of PPTA and PBD with the same composition.     

Synthesis and properties of novel soluble and high Tg poly(ether imide)s from diamine containing 4,5‐diazafluorene and trifluoromethyl units

The synthesis and properties of soluble, high T_g and transparent aromatic polyimides containing 4,5‐diazafluorene and trifluoromethyl units in the polymer backbone on the basis of a novel diamine monomer, 9,9‐di[4‐(4‐amino‐2‐trifluoromethyl phenoxy)phenylene]‐4,5‐diazafluorene, are described. Incorporation of 4,5‐diazafluorene and trifluoromethyl groups into rigid polyimides improves their solubility and transparency without decreasing their physical properties. All of the thermal imidization polyimides are soluble at room temperature in aprotic and protic polar solvents such as N,N‐dimethylacetamide, N,N′‐dimethylformamide, dimethylsulfoxide, pyridine and m‐cresol and can be solution cast into transparent, flexible and tough films. These films have a UV–visible absorption cutoff wavelength at 386–407 nm and light transparencies of 73%–84% at a wavelength of 550 nm. In addition, the polymers exhibit high thermal stability with a glass transition temperature (T_g) of 305 to 362 °C and 5% weight loss at temperatures ranging from 525 to 543 °C in nitrogen and from 521 to 538 °C in air. The polyimide films possess tensile strengths in the range 79 ? 113 MPa, a tensile modulus of 1.75 – 2.10 GPa and elongations at break of 7% ? 16%. © 2014 Society of Chemical Industry     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

High molecular weight poly(p-arylene sulfide ketone): synthesis and membrane-forming properties

High-molecular-weight poly(p-arylene sulfide ketone) (PPSK) was prepared by nucleophilic substitution reaction of 4,4’-diflurobenzophenone (DFBP) and sodium sulfide in the compound solvents of diphenyl sulfone (DPS) and 1,3-dimethyl-2-imidazolidinone (DMI) with catalysts under elevated temperature. The inherent viscosity (η_int) of the PPSK synthesized was 0.703 dl/g. PPSK was characterized by Fourier-transform infrared spectroscopy, elemental analysis, x-ray diffraction, differential scanning calorimetry, and thermogravimetric analysis. It was found that the polymer had excellent thermal properties: glass transition temperature (T_g) was 142.8 °C, melting temperature (T_m) was 362.3 °C. Under nitrogen atmosphere, 5 % (T_5%) and 10 % (T_10%) weight-loss temperatures were about 498.5 °C and 526.2 °C, respectively, while in the air the T_5% and T_10% were about 517 °C and 535.8 °C, respectively. The PPSK was found to be a semi-crystalline polymer, as confirmed by XRD. The polymer was insoluble in any solvent except concentrated sulfuric acid at room temperature. A series of the PPSK separating membranes were prepared by dissolving PPSK to concentrated sulfuric acid. The fluxes and the porosities of the separating membranes were in the range of 230–43 L/(m²?·?h) and 77.7-84.7 %, respectively. At the same time, these separating membranes showed moderate tensile strength of 1.02-1.88 MPa.     

Preparation,analysis, and isothermal crystallization behavior of poly[1,3‐bis(aminomethyl)cyclohexamethylene oxamide]

Poly[1,3‐bis(aminomethyl)cyclohexaneoxamide] (PBAC2) was synthesized using 1,3‐bis(aminomethyl)cyclohexane (BAC) and dibutyl oxalate (DO) via spray/solid‐state polycondensation (SSP). The structure of the synthesized polyoxamide was confirmed by ¹H‐nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy. The weight average molecular weight (M_w) of the polyoxamides prepared was 1.35 × 10⁵. The polyoxamides showed excellent thermal properties with glass transition temperature (T_g) of 150 °C, melting temperature (T_m) of 318 °C, crystallization temperature(T_c) of 253 °C, and initial degradation temperature (T_d) of 417 °C suggesting higher thermal stability than commercial polyamide 6 (T_d = 378 °C). Kinetic studies of PBAC2 predicted a two‐dimensional crystal growth. X‐ray diffraction powder diffraction suggested that the polymer has high crystallinity. A saturated water absorption of 2.8 wt % was recorded for the new polyoxamide, giving it a competitive edge for applications in civil aviation, reinforced plastics, and electronics industry where precise dimensional stability and high thermal resistance properties are a priority. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46345.     

Crystal structure and thermodynamic parameters of Nylon-1010

WAXD, SAXS, FTIR, DSC and density techniques have been used to investigate the crystal structure, crystal density ρ_c, amorphous density p_a equilibrium heat of fusion δH°_m and equilibrium melting temperature T°_m. By extrapolating the straight lines in the FTIR absorbance against density plot to zero intensity. ρ_c and ρ_a were estimated to be 1.098 and 1.003 g/cm³ respectively. The ρ_c obtained was too low in value. From X-ray diffraction patterns of uniaxially oriented fibres, the crystal structure of Nylon-1010 was determined. The Nylon-1010 crystallized in the triclinic system, with lattice dimensions: a = 4.9 Å, b = 5.4 Å, c = 27.8 Å, α = 49°, β = 77°, γ = 63.5°. The unit cell contained one monomeric unit, the space group was P1 , and the correct value of ρ_c was 1.135 g/cm³. The degree of crystallinity of the polymer was determined as about 60% (at RT) using Ruland's method. SAXS has been used to investigate the crystalline lamellar thickness, long period, transition zone, the specific inner surface and the electron density difference between the crystalline and amorphous regions for Nylon-1010. The analysis of data was based upon a one-dimensional electron-density correlation function. δ H°_m was estimated to be 244.0 J/g by extrapolation of δH°_m in the plot of heat of fusion against specific volume of semicrystalline specimens to the completely crystalline condition (V = 1/ρ_c). Owing to the ease of recrystallization of melt-crystallized Nylon-1010 specimens, the well-known Hoffman's T_m-T_c method failed in determining T°_m and a Kamide double extrapolation method was adopted. The T°_m value so obtained was 487 K.     

Study of the effect of annealing,draw ratio,and moisture upon the crystallinity of native and commercial gutta percha (transpolyisoprene) with DSC,DMTA, and X-rays: Determination of the activation energies at Tg

The transitions occurring in gutta-percha (transpolyisoprene) below the melting point were determined with DMTA and DSC. A comparison of the results obtained with these two methods showed satisfactory agreement. The thermal properties of native and commercial gutta-percha samples (T_g = 38 ± 2°C and T_m = 69 ± 3°C) were investigated, both before and after annealing (at different times and temperatures), and at environments of different relative humidities. An increase in the draw ratio also proved to enhance the percentage crystallinity (% K) and improve the thermal stability (higher T_gs and T_ms) of gutta-percha. Finally, the activation energies ΔE (33.9–40.2 kj/mol × K) at glass transition temperature were determined and correlated to the percentage content (%) of the commercial gutta-percha samples in native gutta-percha. © 1993 John Wiley & Sons, Inc.