TiB_2/SiC陶瓷复合材料制备工艺的研究

以TiO2、B4C和C为原料,基于原位合成法在SiC基体中生成TiB2颗粒,并采用无压烧结法制备出TiB2/SiC复合陶瓷.通过对复合材料制备工艺的研究,发现：高于1 300℃的预烧结能形成TiB2/SiC复合陶瓷坯体.C含量、烧结温度和保温时间对复合材料的相对密度均有影响.当C含量（质量分数）为4%时、在1 400℃×60 min＋2000℃×30 min的烧结工艺下能够制备出致密的TiB2/SiC陶瓷复合材料.微米级TiO2粉比纳米级TiO2粉更有利于形成较致密的烧结复合材料.随着生成TiB2体积分数的增加（5%～20%）,复合材料中TiB2颗粒逐渐粗化,间距逐渐变小.对复合材料的烧结机理还进行了分析.     

原位合成方镁石-铁铝尖晶石材料的烧结工艺及性能研究

以镁砂细粉、Fe粉、Fe2O3粉和α-Al2O3粉为原料,采用原位合成法制备方镁石-铁铝尖晶石材料。不同气氛下烧成试验显示N2气氛是合成铁铝尖晶石的最佳气氛。通过XRD和SEM分析在N2气氛中不同热处理温度制备铁铝尖晶石材料的相组成及其显微结构,研究了烧结温度和铁加入量对试样烧结性能的影响。结果表明,试样在N2气氛中于1450、1500、1550℃下保温3h处理后都能原位合成出方镁石-铁铝尖晶石材料;烧结温度的提高有利于铁铝尖晶石的发育和试样烧结性能的提高;铁加入量为10％时烧结性能最佳。     

TiB2/Cu复合材料组织与性能的研究

以Ti、B和Cu的单质粉末为原料,经混粉-冷压成形-真空烧结,制备出原位自生TiB2陶瓷颗粒增强铜基复合材料.并借助热分析方法和X射线衍射对增强颗粒进行分析,同时通过扫描电子显微镜对复合材料组织进行观察,进一步测定复合材料的力学性能.结果表明,在Ti-B-Cu体系中,通过原位反应生成增强相是TiB2.随着B粉和Ti粉含...     

放电等离子烧结含铝Ti_3SiC_2相的形成规律研究

用放电等离子烧结工艺以元素粉为原料制备 Ti3Si C2 材料时 ,掺入适量铝能改善 Ti3Si C2 的反应合成。应用 X-射线衍射和扫描电子显微镜研究不同烧结温度下材料的相组成和显微结构特征。结果表明 :含铝 Ti3Si C2 相在 110 0℃开始大量形成 ,经 115 0～ 12 5 0℃烧结 ,能制备纯净致密含铝 Ti3Si C2 固溶体材料。铝的固溶降低了 Ti3Si C2 的化学热稳定性 ,使其分解温度降低至 130 0℃。     

B4C/TiO2/Al复合材料制备及其性能

采用热压法制备了B4C/TiO2/Al复合陶瓷材料，试验结果表明，TiO2和Al的加入，使得B4C/TiO2/Al复合材料的硬度、抗弯强度和断裂韧性比纯B4C陶瓷材料有较大程度的提高；而且，添加相促进了复合材料的烧结.利用热力学和X射线衍射分析研究烧结过程中的化学反应，分析结果表明，复合材料中没有发现TiO2，Al，Al2O3；同时在复合材料中出现了TiB2，因为在热压过程中TiO2与B4C反应生成TiB2.分析了B4C/TiO2/Al复合陶瓷材料的微观结构和增韧机理.     

包覆工艺制备C—SiC—B4C—TiB2复合材料的组织与性能

以鳞片石墨,B4C,SiC,TiO2为原料,利用包覆工艺在不同热压温度下制备了W（C）=50％的C—SiC—B4C—TiB2复合材料,并详细研究了热压温度对复合材料显微组织和性能的影响规律．结果表明,当热压温度高于1850℃时,复合材料由C,SiC,B4C和TiB2这四相组成;复合材料的体积密度、抗折强度和断裂韧性均随着热压温度的升高而增加．2000oC热压时,复合材料的体积密度、气孔率、抗折强度和断裂韧性分别达到2．41g／cm^3,3．42％,176MPa和6．1MPa·m^1/2;热压温度升高,复合材料的碳相和陶瓷相逐渐致密,碳相最终形成了在陶瓷基体上镶嵌的直径为40μm橄榄球状和条状这两种形貌．碳／陶瓷相的弱界面分层诱导韧化和第二相TiB2与陶瓷基体之间热膨胀系数不匹配所致的残余应力使变形过程中微裂纹的扩展路径发展变化,使复合材料的韧性提高．     

LiNbO3/Al2O3复合材料的制备及其力学性能

为了研究铁电相LiNbO3对Al2O3陶瓷材料结构及其力学性能的影响,以Al2O3 Nb2O5 和LiCO3为主要原料,分别通过高温固相法和热压烧结法,制备LiNbO3/Al2O3复合材料.对制备的复合材料进行物相分析,抗折强度的测试以及显微形貌观察.结果发现：LiNbO3的加入有利于促进Al2O3的烧结,降低了Al2O3陶瓷的烧结温度.当烧结温度超过1 200℃时,复合材料的主晶相仍然为LiNbO3和Al2O3,但由于少量Li元素挥发,生成物相LiNb3O8.在1 200℃保温3h,通过高温固相法烧结,5vol％ LiNbO3/95vol％ Al2O3复合材料的抗弯强度达到了最高,为162.34MPa.在1 300℃,150MPa（保温保压1h）热压烧结制备的15 vol％ LiNbO3/85 vol％ Al2O3复合材料致密度为92.82％,其抗弯强度和断裂韧性分别为393.94 MPa和2.38 MPa· m1/2.该复合材料中的LiNbO3晶粒出现了非180°畴结构,这种电畴结构有利于改善材料的力学性能.     

退火温度对Nd4.2Dy0.8Pr4Fe85Nb1B5纳米复合材料磁性能的影响

用熔体快淬和晶化处理的方法制备了Nd4.2Dy0.8Pr4Fe85 Nb1B5纳米复合材料,研究了退火温度对材料磁性能的影响.结果表明,经不同退火温度进行退火处理得到的Nd4.2 Dy0.8Pr4Fe85Nb1B5纳米复合材料的磁性能不同,在580℃下退火处理3 min得到的样品具有最佳磁性能,即Hci=6787.0 ...     

铜基受电弓滑板试件电阻率和磨损性能研究

为了制备具有优良电阻率和磨损性能的 C/Cu 复合材料,运用传统的粉末冶金(PM)方法,首次将受电弓滑板材料中 C 的质量分数提高到8%(采用大粒度石墨的粒度为50目和32目),分析了压制压力、烧结保温时间和烧结温度对其电阻率和磨损性能的影响.研究了石墨粒度和镀铜石墨对受电弓滑板材料性能的影响.研究结果表明:如果增大压制压力,电阻率下降;而延长烧结保温时间和提高烧结温度,使材料的电阻率增加.烧结温度过高或过低对材料的耐磨性和减摩性不利.石墨粒度越大,电阻率越小,减摩性和耐磨性越差.镀铜石墨能够改善铜基受电弓滑板材料的烧结过程,降低其孔隙度和电阻率,提高其耐磨性和减摩性,但不改变材料的磨损机理.     

均相沉淀法制备Zn Fe2 O4负极材料及其储锂性能

采用均相沉淀法制备了ZnFe2 O4前驱体,探索了烧结温度对ZnFe2 O4结构和电化学性能的影响。用X射线衍射（XRD）和场发射扫描电子显微镜（FESEM）表征了材料的微观结构和形貌;采用循环伏安（CV）、电化学交流阻抗谱（EIS）和充放电测试了ZnFe2 O4作为锂离子电池负极材料的储锂性能。结果表明：随着烧结温度的升高,样品粒径增大;当烧结温度达到900℃时可以得到纯相尖晶石型ZnFe2 O4,其中在900℃下烧结的ZnFe2 O4样品具有最高的嵌锂活性、最好的电化学反应可逆性、最低的电化学反应阻抗和优良的倍率性能。     

等离子烧结法制备FeAl/Al2O3复合材料

利用机械活化-放电等离子烧结的方法,将Fe-Al-Al2O3粉末经机械活化后快速烧结,得到致密且晶粒细小的FeAl/Al2O3块体复合材料.研究表明,在w（球）∶w（粉）=13∶1、转速170 r/min、球磨时间25 h的球磨参数下,粉体中的纳米级Al2O3颗粒,在细化和活化Fe、Al金属粉末的同时,还能有效地阻止金属粉末在烧结前合金化生成金属间化合物.在烧结压力40 MPa、烧结温度1050℃、加热时间15 min、保温时间10min的烧结参数下,制备的FeAl/Al2O3复合材料的致密度可达96.4%.     

碳热还原法CaB_6粉体的制备

采用廉价的工业废料硼酸钙（其主要成分为CaO和B2O3,其质量分数共计约75%,下文均简称为硼酸钙）为原料,原料中不足的硼源由B4C或硼酐取代,通过碳热还原法低成本合成CaB6粉体.实验结果表明以B4C为反应物所制备得到的CaB6粉体的转化率高于以硼酐为反应物的试样.以硼酸钙,B4C和碳为原料的CaB6粉体合成的最佳烧结工艺为1923 K保温30 min.     

The Effects of Solid Phase Additives on Sintering Properties of Alumina Bioceramic

1　IntroductionAlumina (Al2 O3 )bioceramicsarewidelyusedinclinicforhardtissuesubstitution ,especiallyforfemurballofartificialhipjoint.Al2 O3 materialhasgoodbiocompati bility ,physiologicinertia ,physicalandchemicalstability ,highhardnessandwearability .Butundernormalcondi tions,pureAl2 O3 isdifficulttobepreparedbecausethesinteringtemperatureishigh (generallyat 170 0℃to2 0 0 0℃ )andtheheat pressure ,atmosphereorvacuumareevenrequired .Inordertoreducethesinteringtemperatureandimprovetheproper…     

Processing and characterization of B_4C/Cu graded composite as plasma facing component for fusion reactors

A new approach for fabricating B4C/Cu graded composite by rapid self-resistance sintering under ultra-high pressure was presented, by which a near dense B4C/Cu graded composite with a compositional spectrum of 0-100% was successfully fabricated. Plasma relevant performances of sintered B4C/Cu composite were preliminarily characterized, it is found that its chemical sputtering yield is 70% lower than that of SMF800 nuclear graphite under 2.7keV D+ irradiation, and almost no damages after 66 shots of in situ plasma discharge in HL-1 Tokamak facility, which indicates B4C/Cu plasma facing component has a good physical and chemical sputtering resistance performance compared with nuclear graphite.     

3%C-Cu机械球磨复合粉末的烧结

为了给后续的致密化工序（如热挤压）提供较高质量的烧结坯,用扫描电镜和光学显微镜分析了3%C-Cu机械球磨复合粉末所制备烧结坯的显微组织,并研究了工艺参数对其相对致密度的影响规律。结果表明,烧结温度对未机械球磨混合粉烧结行为的影响很大,而机械球磨复合粉对烧结温度不敏感。真空热压烧结可以明显地促进致密化过程。提高烧结温度、延长烧结保温时间或增加热压压强,均有助于提高烧结坯的相对致密度。在相同条件下,烧结坯的相对致密度随着复合粉末机械球磨时间的延长而降低。     

Manufacture of high-dispersed W-Cu composite powder by mechano-thermal process

In order to improve the process of co-reduction of oxide powder, a new mechano-thermal process was designed to produce high-dispersed W-Cu composite powder by high temperature oxidation, short time high-energy milling and reduction at lower temperature. The particle size, oxygen content and their sintering abilities of W-Cu composite powder in different conditions were analyzed. The results show that after a quick milling of the oxide powder for about 3-10 h, the reduction temperature of the W-Cu oxide powder can be lowered to about 650 ℃ from 700-750 ℃ owning to the lowering of particle size of the oxide powder. The average particle size of W-Cu powder after reduction at 650 ℃ is about 0. 5μm smaller than that reduced at 750 ℃. After sintering at 1 200℃ for 1 h in hydrogen atmosphere, the relative density and thermal conductivity of final products (W-20Cu) can attain 99. 5% and 210 W ·m-1· K-1 respectively.     

B4C／TiO2／Al复合材料制备及其性能

采用热压法制备了B4C／TiO2／Al复合陶瓷材料，试验结果表明，TiO2和Al的加入，使得B4C／TiO2／Al复合材料的硬度、抗弯强度和断裂韧性比纯B4C陶瓷材料有较大程度的提高；而且，添加相促进了复合材料的烧结．利用热力学和X射线衍射分析研究烧结过程中的化学反应，分析结果表明，复合材料中没有发现TiO2，Al，Al2O3;同时在复合材料中出现了TiB2，因为在热压过程中TiO2-B4C反应生成TiB2．分析了B4C／TiO2／Al复合陶瓷材料的微观结构和增韧机理．     

Low-temperature sintering of FeCuCo based pre-alloyed powder for diamond bits

We studied the effects of sintering temperature on FeCuCo based pre-alloyed powder for diamond bits.The FeCuCo composite was fabricated by co-precipitation method.With the addition of tungsten carbide(WC),sintering under different temperatures was investigated.Mechanical properties of the FeCuCo based matrix were systematically studied.The structure of the composite was evaluated by X-ray diffraction(XRD) and scanning electron microscope(SEM) was used to analyze the surface of the powder and matrix.The suitable sintering temperature was determined through differential scanning calorimeter(DSC).Micro drilling experiments were performed,and 820 ℃ was identified to be the ideal sintering temperature,at which the matrix shows the best mechanical properties and drilling performance.     

ON ZrO_2-NiCr COMPOSITE POWDER FOR SPRAYING

Composite powder prepared of calcium ox-ide stabilzed ZrO_2 (CSZ)and NiCr by vacuum sintering isstudied, and the effect of additive TiO_2,on its properties isdiscussed. The morphology and phases of the powder weremeasured and determined by SEM.EPMA. XRD methodsand the testing of flowability, bulk density and microhard-ness. The results show that the metallic camponents in thepowder are in homogeneous distribution,the flowability.bulkdensity and microhardness are superior to the ZrO_2-NiCrpowder prepared by mechanically mixing. All components inthe coating made of the composite powder are well-distribut-ed because of avoiding segregation in the middle of mixing.It proves that the comopsite powder is an excellent materialfor plasma spraying.     

Properties, phases and microstructure of microwave sintered W-20Cu composites from spray pyrolysiscontinuous reduction processed powders

The effects of microwave sintering on the properties, phases and microstructure of W-20Cu alloy, using composite powder fabricated by spray pyrolysis-continuous reduction technology, were investigated. Compared with the conventional hot-press sintering, microwave sintering to W-20Cu composites could be achieved with lower sintering temperature and shorter sintering time. Furthermore, microwave sintered W-Cu composites with high densification, homogenous microstructure and excellent properties were obtained. Microwave sintering could also result in finer microstructures.