Regeneration of NOx trap catalysts

We have investigated the regeneration of a nitrated or sulphated model Pt/Ba-based NO_x trap catalyst using different reductants. H₂ was found to be more effective at regenerating the NO_x storage activity especially at lower temperature, but more importantly over the entire temperature window after catalyst ageing. When the model NO_x storage catalyst is sulphated in SO₂ under lean conditions at 650 °C almost complete deactivation can be seen. Complete regeneration was not achieved, even under rich conditions at 800 °C in 10% H₂/He. Barium sulphate formed after the high temperature ageing was partly converted to barium sulphide on reduction. However, if the H₂ reduced sample was exposed to a rich condition in a gas mixture containing CO₂ at 650 °C, the storage activity can be recovered. Under these rich conditions the S²⁻ species becomes less stable than the CO₃²⁻, which is active for storing NO_x. Samples which were lean aged in air containing 60 ppm SO₂ at <600 °C, after regeneration at λ=0.95 at 650 °C, have a similar activity window to a fresh catalyst. It is, therefore, important that CO₂ is present during the rich regenerations of the sulphated model samples (as of course it would be under real conditions), as suppression of carbonate formation can lead to sulphide formation which is inactive for NO_x storage.     

Impact of redox conditions on thermal deactivation of NOx traps for diesel

Performance of NO_x traps after high-temperature treatments in different redox environments was studied. Two types of treatments were considered: aging and pretreatment. Lean and rich agings were examined for a model NO_x trap, Pt–Ba/Al₂O₃. These were done at 950 °C for 3 h, in air and in 1% H₂/N₂, respectively. Lean aging had a severe impact on NO_x trap performance, including HC and CO oxidation, and NH₃ and N₂O formation. Rich aging had minimal impact on performance, compared to fresh/degreened performance. Deactivation from lean aging was essentially irreversible due to Pt sintering, but Pt remained dispersed with the rich aging. Pretreatments were examined for a commercially feasible fully formulated NO_x trap and two model NO_x traps, Pt–Ba/Al₂O₃ and Pt–Ba–Ce/Al₂O₃. Pretreatments were done at 600 °C for 10 min, and used feed gas that simulated diesel exhaust under several conditions. Lean pretreatment severely suppressed NO_x, HC, CO, NH₃ and N₂O activities for the ceria-containing NO_x traps, but had no impact on Pt–Ba/Al₂O₃. Subsequently, a relatively mild rich pretreatment reversed this deactivation, which appears to be due to a form of Pt–ceria interaction, an effect that is well known from early work on three-way catalysts. Practical applications of results of this work are discussed with respect to NO_x traps for light-duty diesel vehicles.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Quantification of the in situ DRIFT spectra of Pt/K/γ-A12O3 NOx adsorber catalysts

A method to quantify DRIFT spectral features associated with the in situ adsorption of gases on a NO_x adsorber catalyst, Pt/K/Al₂O₃, is described. To implement this method, the multicomponent catalyst is analysed with DRIFT and chemisorption to determine that under operating conditions the surface comprised a Pt phase, a pure γ-Al₂O₃ phase with associated hydroxyl groups at the surface, and an alkalized-Al₂O₃ phase where the surface –OH groups are replaced by –OK groups. Both DRIFTS and chemisorption experiments show that 93–97% of the potassium exists in this form. The phases have a fractional surface area of 1.1% for the 1.7 nm-sized Pt, 34% for pure Al₂O₃ and 65% for the alkalized-Al₂O₃. NO₂ and CO₂ chemisorption at 250 °C is implemented to determine the saturation uptake value, which is observed with DRIFTS at 250 °C. Pt/Al₂O₃ adsorbs 0.087 μmol CO₂/m²and 2.0 μmol NO₂/m², and Pt/K/Al₂O₃ adsorbs 2.0 μmol CO₂/m²and 6.4 μmol NO₂/m². This method can be implemented to quantitatively monitor the formation of carboxylates and nitrates on Pt/K/Al₂O₃ during both lean and rich periods of the NO_x adsorber catalyst cycle.     

High temperature catalytic combustion of methane and propane over hexaaluminate catalysts: NOx emission characteristics

Several hexaaluminate-related materials were prepared via hydrolysis of alkoxide and powder mixing method for high temperature combustion of CH₄ and C₃H₈, in order to investigate the effect of the concentration of the fuels, O₂ and H₂O on NO_x emission and combustion characteristics. Among the hexaaluminate catalysts, Sr_0.8La_0.2MnAl₁₁O₁₉₋ prepared by the alkoxide method exhibited the highest activity for methane combustion and low NO_x emission capability. NO_x emission at 1500 °C was increased linearly with O₂ concentration, whereas water vapor addition decreased NO_x emission in CH₄ combustion over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst. In the catalytic combustion of C₃H₈ over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst, the amount of NO_x emitted was raised in the temperature range between 1000 and 1500 °C when the C₃H₈ concentration increased from 1 to 2 vol.%. It was found that NO_x emission in this temperature range was reduced effectively by adding water vapor.     

Comparative study of structural properties and NOx storage-reduction behavior of Pt/Ba/CeO2 and Pt/Ba/Al2O3

Differences in the NO_x storage-reduction (NSR) behavior of Pt/Ba/CeO₂ and Pt/Ba/Al₂O₃ have been identified and traced to their different chemical and structural properties. The results show that Pt/Ba/CeO₂ exhibits inferior NO_x storage and, particularly, reduction (regeneration) activity compared to the Al₂O₃ supported catalyst. The incomplete reduction of the stored NO_x-species in Pt/Ba/CeO₂ seems to be caused by a faster and more profound reoxidation of Pt particles during the lean period as evidenced by in situ X-ray absorption spectroscopy. Interestingly, the reduction activity could be significantly improved by a pre-reduction step at mild conditions. Exposure of the Pt/Ba/CeO₂ catalyst to reducing H₂ atmosphere in the temperature range 300–500 °C lead to a moderate increase of Pt particle size which beneficially influenced the regeneration activity. In contrast, pre-reduction at temperatures above 500 °C was unfavorable and resulted in a severe decrease of the regeneration activity, probably due to migration of the partially reduced CeO₂ onto the surface of Pt particles.     

A study of the deactivation by sulfur and regeneration of a model NSR Pt/Ba/Al2O3 catalyst

The deactivation by sulfur and regeneration of a model Pt/Ba/Al₂O₃ NO_x trap catalyst is studied by hydrogen temperature programmed reduction (TPR), X-ray diffraction (XRD), and NO_x storage capacity measurements. The TPR profile of the sulfated catalyst in lean conditions at 400 °C reveals three main peaks corresponding to aluminum sulfates (550 °C), “surface” barium sulfates (650 °C) and “bulk” barium sulfates (750 °C). Platinum plays a role in the reduction of the two former types of sulfates while the reduction of “bulk” barium sulfates is not influenced by the metallic phase. The thermal treatment of the sulfated catalyst in oxidizing conditions until 800 °C leads to a stabilization of sulfates which become less reducible. Stable barium sulfides are formed during the regeneration under hydrogen at 800 °C. However, the presence of carbon dioxide and water in the rich mixture allows eliminating more or less sulfides and sulfates, depending on the temperature and time. The regeneration in the former mixture at 650 °C leads to the total recovery of the NO_x storage capacity even if “bulk” barium sulfates are still present on the catalyst.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Alumina supported cobalt–palladium catalysts for the reduction of NO by methane in stationary sources

In order to improve a “Three Function Catalysts Model”, the present paper deals with alumina based catalysts containing cobalt and palladium for the NO reduction by methane.

The deNO_x temperature window was estimated by adsorption and subsequent desorption of NO in lean conditions. Two NO_x desorption peaks were detected for both catalysts. For Pd(0.63)Co(0.58)/Al₂O₃, the two desorption peaks appeared at 205 and 423 °C, whereas for Pd(0.14)Co(0.57)/Al₂O₃, the maxima desorption temperature peaks were at 205 and 487 °C. In addition, NO oxidation was also studied to evaluate the catalyst first function. It was found that, the oxidation begins on Co–Pd/Al₂O₃ around 250 °C. On Pd(0.63)Co(0.58)/Al₂O₃, 8% of deNO_x were found in the range of the second NO_x desorption peak temperature (410 °C). During TPSR, C_xH_yO_z species such as formaldehyde were detected. These oxygenate species are the reactive intermediate for deNO_x by methane.     

The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

On the dynamic behavior of “NOx-storage/reduction” Pt–Ba/Al2O3 catalyst

The NO_x storage and reduction functions of a Pt–Ba/Al₂O₃ “NO_x storage–reduction” catalyst has been investigated in the present work by applying the transient response and the temperature programmed reaction methods, by using propylene as the reducing agent. It is found that: (i) the storage of NO_x occurs first at BaO and then at BaCO₃, which are the most abundant sites following regeneration of catalyst with propylene; (ii) the overall storage process at BaCO₃ is slower than at BaO; (iii) CO₂ inhibits the NO_x storage at low temperatures; (iv) the amount of NO_x stored up to catalyst saturation at 350 °C corresponds to 17.6% of Ba; (v) the reduction of stored NO_x groups is fast and is limited by the concentration of propylene in the investigated T range (250–400 °C); (vi) selectivity to N₂ is almost complete at 400 °C but is significantly lower at 300 °C due to the formation of NO which can be tentatively ascribed to the presence of unselective Pt–O species.     

The low-temperature performance of NOx storage and reduction catalyst

The catalytic performance and the behavior of NO_x storage and reduction (NSR) over a model catalyst for lean-burn gasoline engines have been mainly investigated and be discussed based on the temperature and reducing agents use in this study. The experimental results have shown that the NO_x storage amount in the lean atmosphere was the same as the NO_x reduction amount from the subsequent rich spike (RS) above the temperature of 400 °C, while the former was greater than the latter below the temperature of 400 °C. This indicated that when the temperature was below 400 °C compared with the NO_x storage stage, the reduction of the stored NO_x is somehow restricted. We found that the reduction efficiencies with the reducing agents decrease in the order H₂ > CO > C₃H₆ below 400 °C, thus not all of the NO_x storage sites could be fully regenerated even using an excessive reducing agent of CO or C₃H₆, which was supplied to the NSR catalyst, while all the NO_x storage sites could be fully regenerated if an adequate amount of H₂ was supplied. We also verified that the H₂ generation more favorably occurred through the water gas shift reaction than through the steam reforming reaction. This difference in the H₂ generation could reasonably explain why CO was more efficient for the reduction of the stored NO_x than C₃H₆, and hinted as a promising approach to enhance the low-temperature performance of the current NSR catalysts though promoting the H₂ generation reaction.     

Insight into the key aspects of the regeneration process in the NOx storage reduction (NSR) reaction probed using fast transient kinetics coupled with isotopically labelled NO over Pt and Rh-containing Ba/Al2O3 catalysts

For the first time, the coupling of fast transient kinetic switching and the use of an isotopically labelled reactant (¹⁵NO) has allowed detailed analysis of the evolution of all the products and reactants involved in the regeneration of a NO_x storage reduction (NSR) material. Using realistic regeneration times (ca. 1 s) for Pt, Rh and Pt/Rh-containing Ba/Al₂O₃ catalysts we have revealed an unexpected double peak in the evolution of nitrogen. The first peak occurred immediately on switching from lean to rich conditions, while the second peak started at the point at which the gases switched from rich to lean. The first evolution of nitrogen occurs as a result of the fast reaction between H₂ and/or CO and NO on reduced Rh and/or Pt sites. The second N₂ peak which occurs upon removal of the rich phase can be explained by reaction of stored ammonia with stored NO_x, gas phase NO_x or O₂. The ammonia can be formed either by hydrolysis of isocyanates or by direct reaction of NO and H₂.

The study highlights the importance of the relative rates of regeneration and storage in determining the overall performance of the catalysts. The performance of the monometallic 1.1%Rh/Ba/Al₂O₃ catalyst at 250 and 350 °C was found to be dependent on the rate of NO_x storage, since the rate of regeneration was sufficient to remove the NO_x stored in the lean phase. In contrast, for the monometallic 1.6%Pt/Ba/Al₂O₃ catalyst at 250 °C, the rate of regeneration was the determining factor with the result that the amount of NO_x stored on the catalyst deteriorated from cycle to cycle until the amount of NO_x stored in the lean phase matched the NO_x reduced in the rich phase. On the basis of the ratio of exposed metal surface atoms to total Ba content, the monometallic 1.6%Pt/Ba/Al₂O₃ catalyst outperformed the Rh-containing catalysts at 250 and 350 °C even when CO was used as a reductant.     

Water-induced bulk Ba(NO3)2 formation from NO2 exposed thermally aged BaO/Al2O3

Phase changes in high temperature treated (>900 °C) 8 or 20 wt% BaO supported on γ-Al₂O₃ model lean NO_x trap (LNT) catalysts, induced by NO₂ and/or H₂O adsorption, were investigated with powder X-ray diffraction (XRD), solid state ²⁷Al magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy, and NO₂ temperature programmed desorption (TPD) experiments. After calcination in dry air at 1000 °C, the XRD and solid state ²⁷Al MAS NMR results confirm that stable surface BaO and bulk BaAl₂O₄ phases are formed for 8 and 20 wt% BaO/Al₂O₃, respectively. Following NO₂ adsorption over these thermally treated samples, some evidence for nanosized Ba(NO₃)₂ particles are observed in the XRD results, although this may represent a minority phase. However, when water was added to the thermally aged samples after NO₂ exposure, the formation of bulk crystalline Ba(NO₃)₂ particles was observed in both samples. Solid state ²⁷Al MAS NMR is shown to be a good technique for identifying the various Al species present in the materials during the processes studied here. NO₂ TPD results demonstrate a significant loss of uptake for the 20 wt% model catalysts upon thermal treatment. However, the described phase transformations upon subsequent water treatment gave rise to the partial recovery of NO_x uptake, demonstrating that such a water treatment of thermally aged catalysts can provide a potential method to regenerate LNT materials.     

An examination of the role of plasma treatment for lean NOx reduction over sodium zeolite Y and gamma alumina Part 2: Formation of nitrogen

NO_x reduction with NO₂ as the NO_x gas in the absence of plasma was compared to plasma treated lean NO_x exhaust where NO is converted to NO₂ in the plasma. Product nitrogen was measured to prove true chemical reduction of NO_x to N₂. With plasma treatment, NO as the NO_x gas, and a NaY catalyst, the maximum conversion to nitrogen was 50% between 180 and 230 °C. The activity decreased at higher and lower temperatures. At 130 °C a complete nitrogen balance could be obtained, however between 164 and 227 °C less than 20% of the NO_x is converted to a nitrogen-containing compound or compounds not readily detected by gas chromatograph (GC) or Fourier transform infrared spectrometer (FT-IR) analysis. With plasma treatment, NO₂ as the NO_x gas, and a NaY catalyst, a complete nitrogen balance is obtained with a maximum conversion to nitrogen of 55% at 225 °C.

For γ-alumina, with plasma treatment and NO₂ as the NO_x gas, 59% of the NO_x is converted to nitrogen at 340 °C. A complete nitrogen balance was obtained at these conditions. As high as 80% NO_x removal over γ-alumina was measured by a chemiluminescent NO_x meter with plasma treatment and NO as the NO_x gas.

When NO is replaced with NO₂ and the simulated exhaust gases are not plasma treated, the maximum NO_x reduction activity of NaY and γ-alumina decreases to 26 and 10%, respectively. This is a large reduction in activity compared to similar conditions where the simulated exhaust was plasma treated. Therefore, in addition to NO₂, other plasma-generated species are required to maximize NO_x reduction.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

Combinatorial preparation and high-throughput catalytic tests of multi-component deNOx catalysts

A quaternary catalyst library of 56 samples comprising all combinations of four elements, viz. Ag, Co, Cu, In, with six equally spaced atomic fraction increments from 0 to 1 was prepared by impregnation of a proprietary mesoporous alumina support. Catalytic properties of the library were tested in the selective catalytic reduction (SCR) of NO_x by propane under lean conditions in the temperature range 400–500 °C. The catalytic data acquired by a parallel 64-channel microreactor system with automated time-of-flight mass spectrometric analysis have been evaluated regarding selectivity–compositional relationships, synergistic effects for NO_x conversion, and efficiency of propane utilization. Full conversion of NO_x is achieved over Ag–Co combinations at 450 °C with N₂ selectivities of more than 90% and reductant utilization of 20% in a feed of 1500 ppm NO, 1500 ppm propane and 5 vol.% O₂ (space velocity of 36,000 cm³ g_cat⁻¹ h⁻¹). For the single-component catalysts Ag/Al₂O₃, Co/Al₂O₃, Cu/Al₂O₃, and In/Al₂O₃, the state of the elements on the mesoporous alumina was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Cobalt forms a spinel-like cobalt aluminate phase whereas copper and indium are present as oxides with small sizes not detectable by XRD. Silver occurs in both metallic state and as Ag₂O, and forms Ag_n clusters of at least two different sizes, predominantly with diameters of about 30 nm. The conclusions are consistent with the reducibility of the single-component catalysts samples by H₂. Surface area measurements and pore size distributions revealed reasonable modifications of the textural properties. The main pore size of the alumina support is decreased from 7 to ca. 5 nm after loading of the active components.     

Comparative study of Pt-based catalysts on different supports in the low-temperature de-NOx-SCR with propene

Pt-based catalysts have been prepared using supports of different nature (γ-Al₂O₃, ZSM-5, USY, and activated carbon (ROXN)) for the C₃H₆-SCR of NO_x in the presence of excess oxygen. Nitrogen adsorption at 77 K, pH measurements, temperature-programmed desorption of propene, and H₂ chemisorption were used for the characterization of the different supports and catalysts. The performance of these catalysts has been compared in terms of de-NO_x activity, hydrocarbon adsorption and combustion at low temperature, and selectivity to N₂. Maximum NO_x conversions for all the catalysts were achieved in the temperature range of 200–250°C. The order of activity was, Pt-USY>Pt/ROXNPt-ZSM-5Pt/Al₂O₃. At temperatures above 300°C only Pt/ROXN maintains a high activity caused by the consumption of the support, while the other catalysts present a strong deactivation. Propene combustion starts at the same temperature for all the catalytic systems (160°C). Complete hydrocarbon combustion is directly related to the acidity of the support, thus determining the temperature of the maximum NO_x reduction. The support play an important role in the reaction mechanism through the hydrocarbon activation. N₂O formation was observed for all the catalysts. N₂ selectivity ranges from 15 to 30% with the order, Pt/ROXN>Pt-USYPt/Al₂O₃>Pt-ZSM-5. The catalytic systems exhibit a stable operation under isothermal conditions during time-on-stream experiments.     

Lean NOx reduction with CO + H2 mixtures over Pt/Al2O3 and Pd/Al2O3 catalysts

The reduction of NO_x by hydrogen under lean burn conditions over Pt/Al₂O₃ is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO_x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al₂O₃. In this case, although pure H₂ and pure CO are ineffective for NO_x reduction under lean burn conditions, H₂/CO mixtures are very effective. With a realistic (1:3) H₂:CO ratio, typical of actual exhaust gas, Pd/Al₂O₃ is significantly more active than Pt/Al₂O₃, delivering 45% NO_x conversion at 160 °C, compared to >15% for Pt/Al₂O₃ under identical conditions. The nature of the support is also critically important, with Pd/Al₂O₃ being much more active than Pd/SiO₂. Possible mechanisms for the improved performance of Pd/Al₂O₃ in the presence of H₂+CO are discussed.     

A new NOx storage-reduction electrochemical catalyst

A new NO_x storage-reduction electrochemical catalyst has been prepared from a polycrystalline Pt film deposited on 8 mol% Y₂O₃-stabilized ZrO₂ (YSZ) solid electrolyte. BaO has been added onto the Pt film by impregnation method. The NO_x storage capacity of Pt-BaO/YSZ system was investigated at 350 °C and 400 °C under lean conditions. Results have shown that the electrochemical catalyst was effective for NO_x storage. When nitric oxides are fully stored, the catalyst potential is high and reaches its maximum. On the other hand, when a part of NO and also NO₂ desorb to the gas phase, the catalyst potential remarkably drops and finally stabilizes when no more NO_x storage occurs but only the reaction of NO oxidation into NO₂. Furthermore, the investigation has clearly demonstrated that the catalyst potential variation versus temperature or chemical composition is an effective indicator for in situ following the NO_x storage-reduction process, i.e. the storage as well as the regeneration phase. The catalyst potential variations during NO_x storage process was explained in terms of oxygen coverage modifications on the Pt.