The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

Effect of Pd precursor salt on the activity and stability of Pd-doped hexaaluminate catalysts for the CH4 catalytic combustion

This study reports the influence of palladium salt precursor on the catalytic activity of palladium-doped hexaaluminate catalysts for the combustion of 1 vol% CH₄ in the presence of CO₂ and H₂O as inhibitors. Thermal stability of the catalysts is evaluated in long-term catalytic test at 700 °C. The hexaaluminate supports were synthesized using two different procedures: conventional coprecipitation and solid/solid diffusion procedure. Palladium impregnation was carried out by two different routes using Pd(NO₃)₂ in water or Pd(acac)₂ in toluene as impregnation solution. It was observed that using Pd(acac)₂ as precursor allows to attain higher dispersion of the active phase (Pd particles size <3 nm). Compared to the catalysts obtained by impregnation of Pd(NO₃)₂, higher catalytic activities are then obtained. Nevertheless, a deactivation of the samples obtained using Pd(acac)₂ is observed. At the end of the stability test, almost similar catalytic activity is obtained whatever the palladium precursor. Reduction–reoxidation experiment showed that this deactivation is irreversible, and TEM analysis suggest that this deactivation is related to the sintering of Pd particles under reaction over samples synthesized using Pd(acac)₂ as precursor.     

Complete oxidation of methane at low temperature over Pt and Pd catalysts for the abatement of lean-burn natural gas fuelled vehicles emissions: influence of water and sulphur containing compounds

The catalytic activity of fresh Pd and Pt catalysts supported on γ-alumina in the complete oxidation of CH₄ traces under lean-burn conditions was studied in the presence or the absence of water or H₂S. Steam-aged catalysts were also studied in order to simulate long-term ageing in real lean-burn natural gas fuelled vehicles (NGVs) exhaust conditions. Without water or H₂S added to the feed, Pd catalysts exhibit a superior catalytic activity in methane oxidation compared to Pt ones, whatever the catalysts were fresh or aged. The addition of 10 vol.% water vapour to the feed strongly affects the activity of the fresh Pd catalyst, thus being only slightly more efficient than the fresh Pt one. H₂S has a strong poisoning effect on the catalytic activity of Pd catalysts, while Pt catalysts are more resistant. The fresh H₂S-poisoned Pd/Al₂O₃ catalyst was studied by TPD in O₂/He. Poisoning species decompose above 873 K as SO₂ and O₂ in relative concentrations consistent with the decomposition of surface sulphate species. However, a treatment in O₂/He at temperatures as high as 923 K does not allow the complete regeneration of the catalytic activity of H₂S-poisoned Pd/Al₂O₃. A mechanism involving the poisoning of PdO by sulphate species is proposed. Different diffusion processes by which these sulphate species can migrate back and forth between PdO and the support, depending on the experimental conditions, are suggested.     

Ultrahigh temperature water gas shift catalysts to increase hydrogen yield from biomass gasification

Noble metal (Rh, Pt, Pd, Ir, Ru, and Ag) and Ni catalysts supported on CeO₂–Al₂O₃ were investigated for water gas shift reaction at ultrahigh temperatures. Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ demonstrated as the best catalysts in terms of activity, hydrogen yield and hydrogen selectivity. At 700 °C and steam to CO ratio of 5.2:1, Pt/CeO₂–Al₂O₃ converted 76.3% of CO with 94.7% of hydrogen selectivity. At the same conditions, the activity and hydrogen selectivity for Ru/CeO₂–Al₂O₃ were 63.9% and 85.6%, respectively. Both catalysts showed a good stability over 9 h of continuous operation. However, both catalysts showed slight deactivation during the test period. The study revealed that Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ were excellent ultrahigh temperature water gas shift catalysts, which can be coupled with biomass gasification in a downstream reactor.     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

Promotion of palladium-based catalysts on metal monolith for partial oxidation of methane to syngas

Four different modifications of alumina were prepared for use as the support for a Pd catalyst used for the partial oxidation of methane to syngas. The catalysts were washcoated on a metallic monolith in order to determine their activities at high gas flow rates. Compared with the Pd/Al₂O₃ catalyst, enhanced partial oxidation activities were observed with the Pd/CeO₂/Al₂O₃, Pd/CeO₂/BaO/Al₂O₃ and Pd/CeO₂/BaO/SrO/Al₂O₃ catalysts. The palladium particles were better dispersed in the presence of CeO₂ and SrO. Adding BaO, CeO₂ and BaO–CeO₂ to γ-Al₂O₃ prevented the transformation of the alumina phase during the 3-day aging process at 1000 °C, providing the support with some level of thermal stability. The addition of small amounts of SrO to the CeO₂/BaO/Al₂O₃ support enhanced the thermal stability of the Pd particles and minimized their sintering. The triply promoted Pd catalyst studied in this work was effective in carrying out partial oxidation at high temperatures, with BaO and CeO₂ promoting the thermal stability of the support, CeO₂ and SrO dispersing the Pd particles and SrO anchoring the Pd particles strongly to the support. The composition of the catalyst which gave both the highest partial oxidation activity and the best thermal stability was Pd(2)/CeO₂(23)/BaO(11)/SrO(0.8)/Al₂O₃.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

助剂Ba对Pd/Al_2O_3和Pt/Al_2O_3催化剂的C1-C3烷烃催化燃烧性能的影响

通过浸渍法制备了Al_2O_3负载的Pd和Pt催化剂,考察催化剂的甲烷、乙烷和丙烷催化燃烧活性,以及助剂Ba对催化性能的影响。对于Pd/Al_2O_3催化剂,加入Ba使活性物种PdO颗粒变大和还原温度升高,形成更稳定的PdO活性物种,是Pd-Ba/Al_2O_3催化剂活性提升的主要原因。对于Pt/Al_2O_3催化剂,加入Ba助剂使活性物种Pt0含量降低,PtO_x与Al_2O_3载体相互作用增强,使PtO_x物种更难被还原为Pt~0,导致Pt-Ba/Al_2O_3催化剂活性降低。Pd和Pt催化剂催化烷烃氧化反应活性规律一致:丙烷乙烷甲烷。Pd/Al_2O_3催化剂有利于C—H键活化,Pt/Al_2O_3催化剂有利于C—C键活化。Pt/Al_2O_3催化剂对C1-C3烷烃氧化活性的差别明显大于Pd/Al_2O_3催化剂。Pt/Al_2O_3催化剂对碳比例高的烷烃活性更高。     

Lean NOx reduction with CO + H2 mixtures over Pt/Al2O3 and Pd/Al2O3 catalysts

The reduction of NO_x by hydrogen under lean burn conditions over Pt/Al₂O₃ is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO_x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al₂O₃. In this case, although pure H₂ and pure CO are ineffective for NO_x reduction under lean burn conditions, H₂/CO mixtures are very effective. With a realistic (1:3) H₂:CO ratio, typical of actual exhaust gas, Pd/Al₂O₃ is significantly more active than Pt/Al₂O₃, delivering 45% NO_x conversion at 160 °C, compared to >15% for Pt/Al₂O₃ under identical conditions. The nature of the support is also critically important, with Pd/Al₂O₃ being much more active than Pd/SiO₂. Possible mechanisms for the improved performance of Pd/Al₂O₃ in the presence of H₂+CO are discussed.     

Reactor and in situ FTIR studies of Pt/BaO/Al2O3 and Pd/BaO/Al2O3 NOx storage and reduction (NSR) catalysts

The reduction of NO under cyclic “lean”/“rich” conditions was examined over two model 1 wt.% Pt/20 wt.% BaO/Al₂O₃ and 1 wt.% Pd/20 wt.% BaO/Al₂O₃ NO_x storage reduction (NSR) catalysts. At temperatures between 250 and 350 °C, the Pd/BaO/Al₂O₃ catalyst exhibits higher overall NO_x reduction activity. Limited amounts of N₂O were formed over both catalysts. Identical cyclic studies conducted with non-BaO-containing 1 wt.% Pt/Al₂O₃ and Pd/Al₂O₃ catalysts demonstrate that under these conditions Pd exhibits a higher activity for the oxidation of both propylene and NO. Furthermore, in situ FTIR studies conducted under identical conditions suggest the formation of higher amounts of surface nitrite species on Pd/BaO/Al₂O₃. The IR results indicate that this species is substantially more active towards reaction with propylene. Moreover, its formation and reduction appear to represent the main pathway for the storage and reduction of NO under the conditions examined. Consequently, the higher activity of Pd can be attributed to its higher oxidation activity, leading both to a higher storage capacity (i.e., higher concentration of surface nitrites under “lean” conditions) and a higher reduction activity (i.e., higher concentration of partially oxidized active propylene species under “rich” conditions). The performance of Pt and Pd is nearly identical at temperatures above 375 °C.     

Application of Ce0.33Zr0.63Pr0.04O2-supported noble metal catalysts in the catalytic wet air oxidation of 2-chlorophenol: Influence of the reaction conditions

In this work, different procedures, namely carbonate coprecipitation and modified solid–solid diffusion, were used to prepare hexaaluminate samples, unsupported or supported onto θ-Al₂O₃. These samples were used as catalyst for the methane total oxidation as synthesized or after impregnation of 1 wt% Pd. It was observed that the modified solid–solid diffusion procedure is an efficient method to obtain the hexaaluminate structure. At a theoretical ratio x of hexaaluminate onto Al₂O₃ less than 0.6 (xLa_0.2Sr_0.3Ba_0.5MnAl₁₁O₁₉ + (1−x)·Al₂O₃, with x = 0.25, 0.60), samples with high specific surface area and θ-Al₂O₃ structure are then obtained. Large differences in catalytic activity can be observed among the series of sample synthesized. All the pure oxide samples (i.e. without palladium) present low catalytic activity for methane total oxidation compared to a reference Pd/Al₂O₃ catalyst. The highest activity was obtained for the samples presenting a θ-Al₂O₃ structure (with x = 0.60) and a high surface area. Impregnation of 1 wt% palladium resulted in an increase in catalytic activity, for all the solids synthesized in this work. Even if the lowest light-off temperature was obtained on the reference sample, similar methane conversions at high temperature (700 °C) were obtained on the stabilized θ-Al₂O₃ solids (x = 0.25, 0.60). Moreover, the reference sample is found to strongly deactivate with reaction time at the temperature of test (700 °C), due to a progressive reduction of the PdO_x active phase into the less active Pd° phase, whereas excellent stabilities in reaction were obtained on the pure and palladium-doped hexaaluminate and supported θ-Al₂O₃ samples. This clearly showed the beneficial effect of the support for the stabilization of the PdO_x active phase at high reaction temperature. These properties are discussed in term of oxygen transfer from the support to the palladium particle. Oxygen transfer is directly related to the Mn³⁺/Mn²⁺ redox properties (in the case of the hexaaluminate and stabilized θ-Al₂O₃ samples), that allows a fast reoxidation of the metal palladium sites since palladium sites reoxidation cannot occur directly by gaseous dioxygen adsorption and dissociation on the surface.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Performance of spent sulfide catalysts in hydrodesulfurization of straight run and nitrogen-removed gas oils

After the test run of several months two kinds of commercial catalysts (NiMo/Al₂O₃ and CoMo/Al₂O₃) were examined in hydrodesulfurization (HDS) of straight run (SRGO) and nitrogen-removed gas oils, at 340 °C under 50 kg/cm² H₂. Hydrogen renewal between stages was attempted to show additional inhibition effects of the by-products such as H₂S and NH₃. Spent NiMo/Al₂O₃ and CoMo/Al₂O₃ catalysts showed contrasting activities in HDS and susceptibility to nitrogen species, according to their catalytic natures, compared to those of their virgin ones. HDS over spent NiMo/Al₂O₃ was significantly improved by removal of nitrogen species, while that over spent CoMo/Al₂O₃ was much improved by H₂ refreshment. The activity for refractory sulfur species such as 4,6-dimethyldibenzothiophene was reduced more severely than that for the reactive sulfur species such as benzothiophenes over spent catalysts. The effects of both two-stage hydrodesulfurization and nitrogen-removal were markedly reduced over the spent NiMo when compared with those over virgin NiMo one. The acidity of the catalysts was correlated with the inhibition susceptibility by nitrogen species as well as H₂S and NH₃. Spent catalysts apparently lost their activity due to the carbon deposition, which covered the active sites more preferentially. The spent NiMo catalyst carried more deposited carbon with larger C/H ratio and nitrogen content. Higher acidity was found to be present on the NiMo catalyst, but this was greatly decreased by the carbon deposition. Additionally, the reactivity of nitrogen species in HDS was briefly discussed in relation to the acidity of the catalyst and its deactivation by carbon deposition.     

Sulphur poisoning and regeneration of precious metal catalysed methane combustion

In many of the applications of catalytic combustion small amounts of sulphur compounds are present in the feed gas. In the case of natural gas combustion, and solid fuel syngas, the sulphur compounds are in reduced forms. The present work investigates the influence of small quantities of reduced sulphur compounds on the combustion of methane over alumina-supported precious metal catalysts. The kinetics of the methane combustion in the presence of low concentrations of a mixture of sulphur compounds (ethyl mercaptan, methyl mercaptan, carbonyl sulphide and hydrogen sulphide) are compared with those in the absence of sulphur compounds. The ease of regeneration of the poisoned catalysts, via low temperature reduction with hydrogen, is also examined. In the conditions studied all catalysts have reduced activity in the presence of the sulphur-based gas mixture, but Pt/Al₂O₃ and Rh/Al₂O₃ are more strongly poisoned than Pd/Al₂O₃. Qualitative studies using gas chromatography with atomic emission detection of the exhaust gases, and FTIR spectroscopy of the spent Rh/Al₂O₃ catalyst, suggest that the catalysts experience a mixture of reduced and oxidised species under reaction conditions, and that sulphating of the support occurs. The regeneration step facilitates metal mobility and meets with varying success depending upon the metal. Pt/Al₂O₃ in particular is difficult to regenerate by reduction in hydrogen (400 °C for 0.5 h), and agglomeration is observed by TEM. Rh/Al₂O₃ regenerates well, and low metal particle size is maintained. A non-linear deactivation model is tested to separate sulphur-induced deactivation from ‘natural’ deactivation in the reaction mixture and preliminary results are presented.     

Tetralin hydrogenation catalyzed by Mo2C/Al2O3 and WC/Al2O3 in the presence of H2S

Supported molybdenum and tungsten carbides were synthesized by temperature-programmed reactions. These materials were characterized by XRD, EDS analysis, HRTEM and CO chemisorption. Hydrogenation of tetralin was carried out at a total pressure of 4 MPa (3.06 MPa of H₂), at 573 K, without or with sulfur (200 ppm of sulfur as DMDS). The resulting activities were compared with those of MoS₂/Al₂O₃ and Pt (1% (w/w) metal loading) supported on Al₂O₃ or SiO₂. In the absence of sulfur, WC/Al₂O₃ showed an initial activity similar to that of Pt/SiO₂, higher than that of MoS₂/Al₂O₃ but lower than that of Pt/Al₂O₃. In the presence of H₂S, WC/Al₂O₃ showed a steady-state activity similar to that of Pt/Al₂O₃ (which suffered a marked deactivation). Post-reaction characterization did not show any sulfur poisoning of the supported carbides. Therefore the supported carbides are sulfur-tolerant and promising catalysts for the hydrogenation of aromatics in diesel fuels in the presence of small amounts of S-containing compounds.     

Catalytic combustion of methane over bimetallic Pd–Pt catalysts: The influence of support materials

The effect of support material on the catalytic performance for methane combustion has been studied for bimetallic palladium–platinum catalysts and compared with a monometallic palladium catalyst on alumina. The catalytic activities of the various catalysts were measured in a tubular reactor, in which both the activity and stability of methane conversion were monitored. In addition, all catalysts were analysed by temperature-programmed oxidation and in situ XRD operating at high temperatures in order to study the oxidation/reduction properties.

The activity of the monometallic palladium catalyst decreases under steady-state conditions, even at a temperature as low as 470 °C. In situ XRD results showed that no decomposition of bulk PdO into metallic palladium occurred at temperatures below 800 °C. Hence, the reason for the drop in activity is probably not connected to the bulk PdO decomposition.

All Pd–Pt catalysts, independently of the support, have considerably more stable methane conversion than the monometallic palladium catalyst. However, dissimilarities in activity and ability to reoxidise PdO were observed for the various support materials. Pd–Pt supported on Al₂O₃ was the most active catalyst in the low-temperature region, Pd–Pt supported on ceria-stabilised ZrO₂ was the most active between 620 and 800 °C, whereas Pd–Pt supported on LaMnAl₁₁O₁₉ was superior for temperatures above 800 °C. The ability to reoxidise metallic Pd into PdO was observed to vary between the supports. The alumina sample showed a very slow reoxidation, whereas ceria-stabilised ZrO₂ was clearly faster.     

Al18B4O33 aluminium borate: A new efficient support for palladium in the high temperature catalytic combustion of methane

Well crystallised aluminium borate Al₁₈B₄O₃₃ has been synthesised from alumina and boric acid with a BET area of 18 m²/g after calcination at 1100 °C. Afterwards, 2 wt.% Pd/Al₁₈B₄O₃₃ was prepared by conventional impregnation of Pd(NO₃)₂ aqueous solution and calcination in air at 500 °C. The catalytic activity of Pd/Al₁₈B₄O₃₃ in the complete oxidation of methane was measured between 300 and 900 °C and compared with that of Pd/Al₂O₃. Pd/Al₁₈B₄O₃₃ exhibited a much lower activity than Pd/Al₂O₃ when treated in hydrogen at 500 °C or aged in O₂/H₂O (90:10) at 800 °C prior to catalytic testing. Surprisingly, a catalytic reaction run up to 900 °C in the reaction mixture induced a steep increase of the catalytic activity of Pd/Al₁₈B₄O₃₃ which became as active as Pd/Al₂O₃. Moreover, the decrease of the catalytic activity observed around 750 °C for Pd/Al₂O₃ and attributed to PdO decomposition into metallic Pd was significantly shifted to higher temperatures (820 °C) in the case of Pd/Al₁₈B₄O₃₃. The existence of two distinct types of PdO species formed on Al₁₈B₄O₃₃ and being, respectively, responsible for the improvement of the activity at low and high temperature was proposed on the basis of diffuse reflectance spectroscopy and temperature-programmed desorption of O₂.     

Investigations of sulphur deactivation of NOx storage catalysts: influence of sulphur carrier and exposure conditions

The influence of SO₂, H₂S and COS in low concentrations on the deactivation of Pt/Rh/BaO/Al₂O₃ NO_x storage catalysts was investigated. Different samples of the catalyst were exposed to synthetic gas mixtures mimicking lean/rich engine cycling in a mixed lean application at 400 °C. The lean gas mixture contained 8 vol.% O₂, 500 vol-ppm C₃H₆ and 400 vol-ppm NO balanced to 100 vol.% with Ar. The rich excursions were performed by switching off the oxygen supply. Sulphur, 25 vol-ppm of either SO₂, H₂S or COS, was added to the gas flow either during the lean, the rich or both periods. This procedure aimed at investigating the influence of the exposure conditions and therefore the lean and rich periods were kept equally long (5 min). In addition, thermodynamical calculations for the prevailing conditions were performed.

It was concluded that all sulphur compounds investigated, i.e. SO₂, H₂S and COS, had similar, negative impact on the NO_x storage ability of the catalyst and that they all showed increased deactivation rates during rich exposure compared to lean. During lean exposure, all sulphur carriers showed similar behaviour, while H₂S and COS caused severe loss of noble metal activity during rich exposure.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.