SWAN: high-level simulation methodology for digital substrate noise generation

Substrate noise generated by the switching digital circuits degrades the performance of analog circuits embedded on the same substrate. It is therefore important to know the amount of noise at a certain point on the substrate. Existing transistor-level simulation approaches based on a substrate model extracted from layout information are not feasible for digital circuits of practical size. This paper presents a complete high-level methodology, which simulates a large digital standard cell-based design using a network of substrate macromodels, with one macromodel for each standard cell. Such macromodels can be constructed for both EPI-type and bulk-type substrates. Comparison of our substrate waveform analysis (SWAN) to several measurements and to several full SPICE simulations indicates that the substrate noise is simulated with our methodology within 10%-20% error in the time domain and within 2 dB relative error at the major resonance in the frequency domain. However, it is several orders of magnitude faster in CPU time than a full SPICE simulation.     

Analysis and experimental verification of digital substrate noisegeneration for epi-type substrates

Substrate coupling in mixed-signal IC's can cause important performance degradation of the analog circuits. Accurate simulation is therefore needed to investigate the generation, propagation, and impact of substrate noise. Recent studies were limited to the time-domain behavior of generated substrate noise and to noise injection from a single noise source. This paper focuses on substrate noise generation by digital circuits and on the spectral content of this noise. To simulate the noise generation, a SPICE substrate model for heavily doped epi-type substrates has been used. The accuracy of this model has been verified with measurements of substrate noise, using a wide-band, continuous-time substrate noise sensor, which allows accurate measurement of the spectral content of substrate noise. The substrate noise generation of digital circuits is analyzed, both in the time and frequency domain, and the influence of the different substrate noise coupling mechanisms is demonstrated. It is shown that substrate noise voltages up to 20 mV are generated and that, in the frequency band up to 1 GHz, noise peaks are generated at multiples of the clock and repetition frequency. These noise signals will strongly deteriorate the behavior of small signal analog amplifiers, as used in integrated front-ends     

一种混合信号集成电路衬底耦合噪声分析方法

讨论分析了混合信号集成电路衬底噪声耦合的机理,及对模拟电路性能的影响。提出了一种混合信号集成电路衬底耦合噪声分析方法,基于TSMC 0.35μm 2P4M CMOS工艺,以14位高速电流舵D/A转换器为例,给出了混合信号集成电路衬底耦合噪声分析方法的仿真结果,并与实际测试结果进行比较,证实了分析方法的可信性。     

Simulation and measurement of supply and substrate noise in mixed-signal ICs

Digital noise in mixed-signal circuits is characterized using a scalable macromodel for substrate noise coupling. The noise coupling obtained through simulations is verified with measured data from a digital noise generator and noise sensitive analog circuits fabricated in the 0.35-/spl mu/m heavily doped CMOS process. The simulations and measurements also demonstrate the effectiveness of including grounded guard rings and separating bulk and supply pins in digital circuits to reduce substrate coupling.     

Modeling of Substrate Noise Generation, Isolation, and Impact for an LC-VCO and a Digital Modem on a Lightly-Doped Substrate

Substrate noise generated by the digital circuits on a mixed-signal IC can severely disturb the analog and RF circuits sharing the same substrate. Simulations at the circuit level of the substrate noise coupling in large systems-on-chip (SoCs) do not provide the necessary understanding in the problem. Analysis at a higher level of abstraction gives much more insight in the coupling mechanisms. This paper presents a physical model to estimate and understand the substrate noise generation by a digital modem, the propagation of this noise and the resulting performance degradation of LC tank VCOs. The proposed linearized model is fast to derive and to evaluate, while remaining accurate. It is validated with measurements on two test structures: a reference design and a design with a$hboxp^+ $/n-well (digital) guard ring. Both structures contain a functional 40k gate digital modem and a 0.18$muhbox m$3.5 GHz CMOS LC-VCO on a lightly-doped substrate. In both cases, the model accurately predicts the level of the spurious components appearing at the VCO output due to the digital switching activity. The error remains smaller than 3 dB. Finally, we demonstrate how the proposed model enables a systematic and controlled isolation strategy to suppress substrate noise coupling problems. As an example, the model is used to determine suitable dimensions for a digital guard ring.     

Measurements and analysis of PLL jitter caused by digital switchingnoise

When integrating analog and digital circuits onto a mixed-mode chip, power supply noise coupling is a major limitation on the performance of the analog circuitry. Several techniques exist for reducing the noise coupling, of which one of the cheapest is separating the power supply distribution networks for the analog and digital circuits. Noise coupling from a digital noise-generating circuit through the power supply/substrate into an analog phase-locked loop (PLL) is analyzed for three different power supply schemes. The main mechanisms for noise coupling are identified by comparing different PLLs and varying their bandwidths. It is found that the main cause of jitter strongly depends on the power supply configuration of the PLL. Measurements were done on mixed-mode designs in a standard 0.25-μm digital CMOS process with a low-resistivity substrate. The same circuits were also implemented with triple-well processing for comparisons     

Substrate model extraction using finite differences and parallel multigrid

Substrate noise in integrated circuits is one of the most important problems in high-frequency mixed-signal designs, such as communication, biomedical and analog signal processing circuits and systems. Fast-switching digital blocks inject noise into the common substrate, hindering the performance of high-precision sensible analog circuitry. Miniaturization trends require increasing the accuracy in substrate coupling simulation environments. However, model extraction and evaluation times should not increase, which demands for fast and still accurate substrate model extraction tools.

In this work, a three-dimensional finite difference extraction methodology is presented. The resulting three-dimensional mesh is efficiently reduced to a circuit-level contact-based model by means of a fast multigrid-based algorithm. Moreover, this contact-based model extraction is shown to be efficiently computed in a parallel environment, resulting in extremely useful extraction speedups. Extraction results prove the proposed method to be very efficient, providing linear time and space complexity, and a constant number of iterations, outperforming competing algorithms.     

Substrate Noise Simulation Techniques for Analog-Digital Mixed LSI Design

Crosstalk from digital to analog circuits can be causative of operation fails in analog-digital mixed LSIs. This paper describes modeling techniques and simulation strategies of the substrate coupling noise. A macroscopic substrate noise model that expresses the noise as a function of logic state transition frequencies among digital blocks is proposed. A simulation system based on the model is implemented in the mixed signal simulation environment, where performance degradation of the 2nd order ADC coupled to digital noise sources is clearly simulated. These results indicate that the proposed behavioral modeling approach allows practicable full chip substrate noise simulation measures.     

Digital circuit capacitance and switching analysis for ground bounce in ICs with a high-ohmic substrate

Substrate noise is a major obstacle for mixed-signal integration. Ground bounce is a major contributor to substrate noise generation due to the resonance caused by the inductance and the Vdd-Vss admittance that consists of the on-chip digital circuit capacitance of the MOS transistors, the decoupling, and the parasitics arising from the interconnect. In this paper, we address: 1) the dependence of the Vdd-Vss admittance on the different states of the circuit, the supply voltage, and the interconnect, and 2) the computation of the total supply current with ground bounce. By using a fast and accurate macromodeling approach, the Vdd-Vss admittances of several test circuits are computed with 2%-3% error relative to the values simulated from the complete SPICE level netlist, but several orders of magnitude faster in CPU time and with 10% maximum error relative to the measurements on a test ASIC fabricated in a 0.18-/spl mu/m CMOS process on a high-ohmic substrate with 18 /spl Omega//spl middot/cm resistivity. The measurements also show that this admittance mainly depends only on the connectivity of the gates to the supply rail rather than their connectivity among each other.     

A simple on-chip repetitive sampling setup for the quantification of substrate noise

The quantification of substrate noise is an important issue in mixed-signal designs, where sensitive analog circuits are embedded in a hostile digital environment. In this paper we present an experimental environment to characterize the sensitivity of embedded analog circuits to digitally generated substrate noise. Our measurement technique is based on equivalent-time substrate voltage sampling and uses a simple differential latch comparator without explicit input sample-and-hold. A surprisingly large measurement bandwidth is observed,which is explained from the detailed circuit behavior. On our 0.18-/spl mu/m CMOS test chip,we have demonstrated that our system allows to wave trace pulses as narrow as 200 ps accurately. Additionally, the extraction of precise measurement data from observations that are excessively corrupted by additive noise and timing jitter is addressed. We present simple yet very effective methods to accurately reconstruct pulse waveform features without the use of delicate deconvolution operations.     

Accurate and efficient simulation of synchronous digital switching noise in systems on a chip

A new method is presented to compress switching information in large synchronous digital circuits. This is combined with an efficient generation of digital cell library noise signatures and results in an accurate estimation of the switching noise in digital circuits. It provides a practical approach to generating the digital switching noise for simulating substrate coupling noise in mixed-signal ICs. Nearly two orders of magnitude reduction in the memory and simulation time are achieved using this approach without significant loss of accuracy.     

Substrate coupling in digital circuits in mixed-signal smart-power systems

This paper describes theoretical and experimental data characterizing the sensitivity of nMOS and CMOS digital circuits to substrate coupling in mixed-signal, smart-power systems. The work presented here focuses on the noise effects created by high-power analog circuits and affecting sensitive digital circuits on the same integrated circuit. The sources and mechanism of the noise behavior of such digital circuits are identified and analyzed. The results are obtained primarily from a set of dedicated test circuits specifically designed, fabricated, and evaluated for this work. The conclusions drawn from the theoretical and experimental analyses are used to develop physical and circuit design techniques to mitigate the substrate noise problems. These results provide insight into the noise immunity of digital circuits with respect to substrate coupling.     

High-Voltage Analog System for a Mobile NAND Flash

High-voltage analog circuits, including a novel high-voltage regulation scheme, are presented with emphasis on low supply voltage, low power consumption, low area overhead, and low noise, which are key design metrics for implementing NAND Flash memory in a mobile handset. Regulated high voltage generation at low supply voltage is achieved with optimized oscillator, high-voltage charge pump, and voltage regulator circuits. We developed a design methodology for a high-voltage charge pump to minimize silicon area, noise, and power consumption of the circuit without degrading the high-voltage output drive capability. Novel circuit techniques are proposed for low supply voltage operation. Both the oscillator and the regulator circuits achieve 1.5 V operation, while the regulator includes a ripple suppression circuit that is simple and robust. Through the paper, theoretical analysis of the proposed circuits is provided along with Spice simulations. A mobile NAND Flash device is realized with an advanced 63 nm technology to verify the operation of the proposed circuits. Extensive measurements show agreement with the results predicted by both analysis and simulation.     

Measurement of digital noise in mixed-signal integrated circuits

This paper proposes a method of measuring the influence of digital noise on analog circuits using wide-band voltage comparators as noise detectors. Noise amplitude and r.m.s voltage are successfully measured by this method. A test chip is fabricated to measure the digital noise influence. From the experimental results, it is shown that the digital noise influence can be considerably reduced by using a differential configuration in analog circuits for mixed-signal IC's. The digital noise influence can be further reduced by lowering the digital supply voltage. These results show that the voltage-comparator-based measuring method is effective in measuring the influence of digital noise on analog circuits     

Performance degradation of LC-tank VCOs by impact of digital switching noise in lightly doped substrates

In mixed analog-digital designs, digital switching noise is an important limitation for the performance of analog and RF circuits. This paper reports a physical model describing the impact of digital switching noise on LC-tank voltage-controlled oscillators (VCOs) in lightly doped substrates. The model takes into account the propagation from the source of substrate noise to the different components in the VCO and the resulting modulation of the oscillator frequency. The model is validated with measurements on a 3.5-GHz LC-tank VCO designed in 0.18-/spl mu/m CMOS. It reveals that for this VCO, impact occurs mainly via the nonideal metal ground lines for lower frequencies and low tuning voltage and via the integrated inductors for higher frequencies and high tuning voltage. To make the design immune to substrate noise, the parasitic resistance of the on-chip ground interconnect has to be kept as low as possible and inductors have to be shielded. Hence, the developed model allows investigating the dominant mechanisms behind the impact of substrate noise on a VCO, which is crucial information for achieving a substrate noise immune design.     

A physical-based noise macromodel for fast simulation of switching noise generation

Efficient prediction of the substrate noise generated by large digital sections is currently a major challenge in System-on-a-Chip design. A macromodel to accurately and efficiently predict the substrate noise generated by digital standard cells is presented. The macromodel is generated from identification of the physical elements relevant to noise generation. Techniques to directly or indirectly compute the values of the elements in the cell macromodel are proposed. Using this macromodel, prediction of the noise generated by large digital sections can be easily done following a methodology based on high-level logic simulation. As a first step to validation, the macromodel accuracy is demonstrated in some circuits consisting of a reduced number of gates.     

Analytical and experimental verification of substrate noise spectrum for mixed-signal ICs

In this paper, the most relevant characteristics of the substrate noise spectrum for mixed-signal integrated circuits (ICs) are derived using a simple analytical model. These characteristics are related to parameters of the digital circuit, the package + printed circuit board parasitics, and other elements of the mixed-signal IC. The model used to derive the substrate noise spectral characteristics includes the statistical properties of the digital switching current waveform and the coupling transfer function between the digital power supply nodes and the substrate node of the victim circuitry. The results of the work are validated experimentally on a mixed-signal prototype.     

Picosecond optical sampling of GaAs integrated circuits

Direct electrooptic sampling is a noncontact optical-probing technique for measuring with picosecond time resolution the voltage waveforms at internal nodes within GaAs integrated circuits. The factors contributing to system bandwidth, sensitivity, spatial resolution, and circuit perturbation are discussed, as are the circuit requirements for realistic testing of analog and digital devices. Measurements of high-speed GaAs integrated circuits are presented, including time-domain waveform and timing measurements of digital and analog circuits and frequency-domain transfer function measurements of microwave circuits and transmission structures     

Efficient methods for modelling substrate coupling in mixed-signalintegrated circuits

A key problem in the design of large mixed-signal circuits is the noise caused by the coupling of digital signals into the substrate. This paper describes methods that allow circuit designers to model efficiently such substrate noise in large mixed-signal SPICE designs. In the light of these techniques a new methodology is presented for efficiently modelling the substrate noise caused by current injection and its coupling to analogue signals; this is then extended to provide a real-time modelling capability. The practicality and the numerical efficiency of the methods are demonstrated on several prototype example circuits     

Experimental results and modeling techniques for substrate noise inmixed-signal integrated circuits

An experimental technique is described for observing the effects of switching transients in digital MOS circuits that perturb analog circuits integrated on the same die by means of coupling through the substrate. Various approaches to reducing substrate crosstalk (the use of physical separation of analog and digital circuits, guard rings, and a low-inductance substrate bias) are evaluated experimentally for a CMOS technology with a substrate comprising an epitaxial layer grown on a heavily doped bulk wafer. Observations indicate that reducing the inductance in the substrate bias is the most effective. Device simulations are used to show how crosstalk propagates via the heavily doped bulk and to predict the nature of substrate crosstalk in CMOS technologies integrated in uniform, lightly doped bulk substrates, showing that in such cases the substrate noise is highly dependent on layout geometry. A method of including substrate effects in SPICE simulations for circuits fabricated on epitaxial, heavily doped substrates is developed