Fabrication and Characterization of Anode‐Supported Low‐Temperature SOFC Based on Gd‐Doped Ceria Electrolyte

Large‐size, 9.5 cm × 9.5 cm, Ni‐Gd_0.1Ce_0.9O_1.95 (Ni‐GDC) anode‐supported solid oxide fuel cell (SOFC) has been successfully fabricated with NiO‐GDC anode substrate prepared by tape casting method and thin‐film GDC electrolyte fabricated by screen‐printing method. Influence of the sintering shrinkage behavior of NiO‐GDC anode substrate on the densification of thin GDC electrolyte film and on the flatness of the co‐sintered electrolyte/anode bi‐layer was studied. The increase in the pore‐former content in the anode substrate improved the densification of GDC electrolyte film. Pre‐sintering temperature of the anode substrate was optimized to obtain a homogeneous electrolyte film, significantly reducing the mismatch between the electrolyte and anode substrate and improving the electrolyte quality. Dense GDC electrolyte film and flat electrolyte/anode bi‐layer can be fabricated by adding 10 wt.% of pore‐former into the composite anode and pre‐sintering it at 1,100 °C for 2 h. Composite cathode, La_0.6Sr_0.4Fe_0.8Co_0.2O₃, and GDC (LSCF‐GDC), was screen‐printed on the as‐prepared electrolyte surface and sintered to form a complete single cell. The maximum power density of the single cell reached 497 mW cm^–2 at 600 °C and 953 mW cm^–2 at 650 °C with hydrogen as fuel and air as oxidant.     

Oxygen Dissociation and Interfacial Transfer Rate on Performance of SOFCs with Metal‐Added (LaSr)(CoFe)O3‐(Ce,Gd)O2 – δ Cathodes

A solid oxide fuel cell (SOFC) unit is constructed with Ni‐Ce_0.9Gd_0.1O_{2 – δ} (GDC) as the anode, yttria‐stabilised zirconia (YSZ) as the electrolyte and Pt, Ag or Cu‐added La_0.58Sr_0.4Co_0.2Fe_0.8O_{3 – δ} (LSCF)–GDC as the cathode. The current–voltage measurements are performed at 800 °C. Cu addition leads to best SOFC performance. LSCF–GDC–Cu is better than LSCF–GDC and much better than GDC as the material of the cathode interlayer. Cu content of 2 wt.‐% leads to best SOFC performance. A cathode functional layer calcined at 800 °C is better than that calcined at higher temperature. Metal addition increases the O₂ dissociation reactivity but results in an interfacial resistance for O transfer. A balance between the rates of O₂ dissociation and interfacial O transfer is needed for best SOFC performance.     

Boosting intermediate temperature performance of solid oxide fuel cells via a tri-layer ceria–zirconia–ceria electrolyte

Using cost-effective fabrication methods to manufacture a high-performance solid oxide fuel cell (SOFC) is helpful to enhance the commercial viability. Here, we report an anode-supported SOFC with a three-layer Gd_0.1Ce_0.9O_1.95 (gadolinia-doped-ceria [GDC])/Y_0.148Zr_0.852O_1.926 (8YSZ)/GDC electrolyte system. The first dense GDC electrolyte is fabricated by co-sintering a thin, screen-printed GDC layer with the anode support (NiO–8YSZ substrate and NiO–GDC anode) at 1400°C for 5 h. Subsequently, two electrolyte layers are deposited via physical vapor deposition. The total electrolyte thickness is less than 5 μm in an area of 5 × 5 cm², enabling an area-specific ohmic resistance as low as 0.125 Ω cm⁻² at 500°C (under open circuit voltage), and contributing to a power density as high as 1.2 W cm⁻² at 650°C (at an operating cell voltage of 0.7 V, using humidified [10 vol.% H₂O] H₂ as fuel and air as oxidant). This work provides an effective strategy and shows the great potential of using GDC as an electrolyte for high-performance SOFC at intermediate temperature.     

Development of an Ionic-Conductive Skeletal Structure for an Electrode-Supported Solid Oxide Fuel Cell

A novel ionic-conductive skeletal structure was developed for an electrode-supported solid oxide fuel cell (SOFC). The skeletal structure was formed as an ionic-conductive frame that accumulated two thick porous layers and one dense thin layer. Two types of green sheets were used to form the frame. Thin green sheets (thickness: 15–30 μm) for the dense layers were fabricated with a well-dispersed Gd_0.2Ce_0.8O _x (GDC) slurry and thick sheets (thickness: 150–300 μm) were fabricated with a GDC/pore-former slurry by the tape casting method. Sintering laminated sheets at 1450°C for 8 h in air resulted in an ionic-conductive frame that was suitable for electrode-supported SOFC. The relative density of the inner thin layer, which works as an electrolyte, was higher than 98%, and the outer thick layers remained porous after the sintering. The porous structure of the outer layers was controlled using agglomerated slurries instead of well-dispersed slurries. Electrochemical measurements of the ionic-conductive frame attached with platinum electrodes exhibited potential as high-performance cells.     

A feasible strategy for tailoring stable spray-coated electrolyte layer in micro-tubular solid oxide fuel cells

By this work, the viability of the spray coating as a cost-effective and reliable technique for the coating of Ce_0.9Gd_0.1O_1.95 (GDC) electrolyte layer on the mini-tubular NiO–GDC anodes based a solid oxide fuel cell (SOFC) fabrication was assessed. The compatibility of the anode and electrolyte was analyzed by using XRD. The variation in thickness and morphology of the electrolyte film as a function of the coating cycles was discussed with optical and scanning electron microscopes. By similar formulation, the coating of La_0.6Sr_0.4Fe_0.8Co_0.2O₃ –Ce_0.9Gd_0.1O_2–δ (LSCF–GDC) was performed to achieve porous cathode. An individual micro-tubular anode supported cell with configuration NiO–GDC/GDC/LSCF–GDC as anode/electrolyte/cathode was tested in the SOFC mode with humidified hydrogen as fuel and stationary air as oxidant. The fabricated mini-SOFC prototype that generated a maximum power density of 0.510 W/cm² at 600°C signifies the potential of this industrially scalable low-cost coating technique.     

Optimisation and Evaluation of La0.6Sr0.4CoO3 – δ Cathode for Intermediate Temperature Solid Oxide Fuel Cells

In this work, La_0.6Sr_0.4CoO_{3 – δ}/Ce_{1 – x}Gd_xO_{2 – δ} (LSC/GDC) composite cathodes are investigated for SOFC application at intermediate temperatures, especially below 700 °C. The symmetrical cells are prepared by spraying LSC/GDC composite cathodes on a GDC tape, and the lowest polarisation resistance (R_p) of 0.11 Ω cm² at 700 °C is obtained for the cathode containing 30 wt.‐% GDC. For the application on YSZ electrolyte, symmetrical LSC cathodes are fabricated on a YSZ tape coated on a GDC interlayer. The impact of the sintering temperature on the microstructure and electrochemical properties is investigated. The optimum temperature is determined to be 950 °C; the corresponding R_p of 0.24 Ω cm² at 600 °C and 0.06 Ω cm² at 700 °C are achieved, respectively. An YSZ‐based anode‐supported solid oxide fuel cell is fabricated by employing LSC/GDC composite cathode sintered at 950 °C. The cell with an active electrode area of 4 × 4 cm² exhibits the maximum power density of 0.42 W cm^–2 at 650 °C and 0.54 W cm^–2 at 700 °C. More than 300 h operating at 650 °C is carried out for an estimate of performance and degradation of a single cell. Despite a decline at the beginning, the stable performance during the later term suggests a potential application.     

Influence of Deposition Temperature of GDC Interlayer Deposited by RF Magnetron Sputtering on Anode‐Supported SOFC

Gadolinia‐doped ceria (GDC) film, as a barrier layer to prevent chemical reaction between yttria‐stabilized zirconia (YSZ) electrolyte and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3–δ (BSCF)–GDC cathode, is deposited by radio frequency (RF) magnetron sputtering on YSZ electrolyte, and the influence of deposition temperature on Ni–YSZ/YSZ/GDC/BSCF–GDC single cell performance is investigated. The SEM results show that the GDC film deposited at 30 °C exhibits a porous structure, whereas the GDC film deposited at 400 °C has a dense structure. The single cells show excellent performance when the deposition temperature is above 250 °C, whereas the single cells show poor performance when the deposition temperature is below 200 °C. The large difference in cell performance occurs from their large difference in polarization resistance. The porous structure of GDC interlayer, which cannot well prevent the reaction between BSCF and YSZ, is responsible for the poor performance of the cells with GDC interlayer deposited at a temperature below 200 °C.     

Characterizations of composite cathodes with La0.6Sr0.4Co0.2Fe0.8O3?δ and Ce0.9Gd0.1O1.95 for solid oxide fuel cells

Composite cathodes with La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF) and Ce_0.9Gd_0.1O_1.95 (GDC) are investigated to assess for solid oxide fuel cell (SOFC) applications at relatively low operating temperatures (650–800 °C). LSCF with a high surface area of 55 m²g⁻¹ is synthesized via a complex method involving inorganic nano-dispersants. The fuel cell performances of anode-supported SOFCs are characterized as a function of compositions of GDC with a surface area of 5 m²g⁻¹. The SOFCs consist of the following: LSCF-GDC composites as a cathode, GDC as an interlayer, yttrium stabilized zirconia (YSZ) as an electrolyte, Ni-YSZ (50: 50 wt%) as an anode functional layer, and Ni-YSZ (50: 50 wt%) for support. The cathodes are prepared for 6LSCF-4GDC (60: 40 wt%), 5LSCF-5GDC (50: 50 wt%), and 4LSCF-6GDC (40: 60 wt%). The 5LSCF-5GDC cathode shows 1.29 Wcm⁻², 0.97 Wcm⁻², and 0.47 Wcm⁻² at 780 °C, 730 °C, and 680 °C, respectively. The 6LSCF-4GDC shows 0.92 Wcm⁻², 0.71 Wcm⁻², and 0.54 Wcm⁻² at 780 °C, 730 °C, and 680 °C, respectively. At 780 °C, the highest fuel cell performance is achieved by the 5LSCF-5GDC, while at 680 °C the 6LSCF-4GDC shows the highest performance. The best composition of the porous composite cathodes with LSCF (55 m²g⁻¹) and GDC (5 m²g⁻¹) needs to be considered with a function of temperature.     

Direct Applicability of La0.6Sr0.4CoO3 – δ Thin Film Cathode to Yttria Stabilised Zirconia Electrolytes at T ≤ 650 °C

For investigating the direct applicability of highly active cobalt containing cathodes on YSZ electrolytes at a lower processing and operating temperature range (T ≤ 650 °C), we fabricated a thin film lanthanum strontium cobalt oxide (LSC) cathode on an yttria stabilised zirconia (YSZ)‐based solid oxide fuel cell (SOFC) via pulsed laser deposition (PLD). Its electrochemical performance (5.9 mW cm^–2 at 0.7 V, 650 °C) was significantly inferior to that (595 mW cm^–2 at 0.7 V, 650 °C) of an SOFC with a thin (t ∼ 200 nm) gadolinium doped ceria (GDC) buffer layer in between the LSC thin film cathode and the YSZ electrolyte. It implies that even though the cathode processing and cell operating temperatures were strictly controlled not to exceed 650 °C, the direct application of LSC on YSZ should be avoided. The origin of the cell performance deterioration is thoroughly studied by glancing angle X‐ray diffraction (GAXRD) and transmission electron microscopy (TEM), and the decomposition of the cathode and diffusion of La and Sr into YSZ were observed when LSC directly contacted YSZ.     

Electrophoretic Deposition of Zirconia Thin Film on Nonconducting Substrate for Solid Oxide Fuel Cell Application

Electrophoretic deposition (EPD) of 8 mol% yttria‐stabilized zirconia (YSZ) electrolyte thin film has been carried out onto nonconducting porous NiO‐YSZ cermet anode substrate using a fugitive and electrically conducting polymer interlayer for solid oxide fuel cell (SOFC) application. Such polymer interlayer burnt out during the high‐temperature sintering process (1400°C for 6 h) leaving behind a well adhered, dense, and uniform ceramic YSZ electrolyte film on the top of the porous anode substrate. The EPD kinetics have been studied in depth. It is found that homogeneous and uniform film could be obtained onto the polymer‐coated substrate at an applied voltage of 15 V for 1 min. After the half‐cell (anode + electrolyte) is co‐fired at 1400°C, a suitable cathode composition (La_0.65Sr_0.3MnO₃) thick film paste is screen printed on the top of the sintered YSZ electrolyte. A second stage of sintering of such cathode thick film at 1100°C for 2 h finally yield a single cell SOFC. Such single cell produced a power output of 0.91 W/cm² at 0.7 V when measured at 800°C using hydrogen and oxygen as fuel and oxidant, respectively.     

Effect of GDC interlayer thickness on durability of solid oxide fuel cell cathode

Long-term performance degradation of solid oxide fuel cell (SOFC) cathode as a function of gadolinium doped ceria (GDC) interlayer thickness has been studied under accelerated operating conditions. For this purpose, SOFC half-cells with GDC interlayer thicknesses of 2.4, 3.4 and 6.0 µm were fabricated and tested for 1000 h at 900 °C under constant current density of 1 A/cm². The half-cells consisted of lanthanum strontium cobalt ferrite (LSCF)/GDC composite cathode, GDC interlayer, scandia-ceria stabilized zirconia electrolyte and platinum anode as a counter electrode. Area specific resistance (ASR) of the half-cells was continuously measured over time. Higher increase in ASR was observed for the half-cells with GDC interlayer thickness of 2.4 and 6.0 µm, which is attributed to higher strontium (Sr) diffusion towards electrolyte and to cathode/GDC interface delamination coupled with small Sr diffusion, respectively. However, half-cell with GDC interlayer thickness of 3.4 µm showed smaller degradation rate due to highly dense GDC interlayer which had less interfacial resistance and suppressed Sr diffusion towards electrolyte.     

Lowering the sintering temperature of solid oxide fuel cell electrolytes by infiltration

A dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400–1500 °C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 °C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 °C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.     

Microstructure and Polarization Studies on Interlayer Free La0.65Sr0.3Co0.2Fe0.8O3–δ Cathodes Fabricated on Yttria Stabilized Zirconia by Solution Precursor Plasma Spraying

Nano‐structured cathodes of La_0.65Sr_0.3Co_0.2Fe_0.8O_3–δ (LSCF) are fabricated by solution precursor plasma spraying (SPPS) on yttria stabilized zirconia (YSZ) electrolytes (LSCF‐SPPS‐YSZ). Phase pure LSCF is obtained at all plasma power. Performances of LSCF‐SPPS‐YSZ cathodes are compared with conventionally prepared LSCF cathodes on YSZ (LSCF‐C‐YSZ) and gadolinium doped ceria (GDC) (LSCF‐C‐GDC) electrolytes. High R_p is observed in the LSCF‐C‐YSZ (∼42 Ohm cm² at 700 °C) followed by LSCF‐C‐GDC (R_p ∼ 1.5 Ohm cm² at 700 °C) cathodes. Performance of the LSCF‐SPPS‐YSZ cathodes (R_p ∼ 0.1 Ohm cm² at 700 °C) is found to be even superior to the performance of LSCF‐C‐GDC cathodes. High performance in LSCF‐SPPS‐YSZ cathodes is attributed to its nano‐structure and absence of any interfacial insulating phase which may be attributed to the low temperature at the interaction point of LSCF and YSZ and low interaction time between LSCF and YSZ during SPPS process. In the time scale of 100 h, no change in the polarization resistances is observed at 750 °C. Based on the literature and from the present studies it can be stated that SOFC with YSZ electrolyte and LSCF‐SPPS‐YSZ cathode can be operated at 750 °C for a longer duration of time and good performance can probably be achieved.     

Thin film yttria-stabilized zirconia electrolyte for intermediate-temperature solid oxide fuel cells (IT-SOFCs) by chemical solution deposition

A 500 nm thick thin film YSZ (yttria-stabilized zirconia) electrolyte was successfully fabricated on a conventionally processed anode substrate by spin coating of chemical solution containing slow-sintering YSZ nanoparticles with the particle size of 20 nm and subsequent sintering at 1100 °C. Incorporation of YSZ nanoparticles was effective for suppressing the differential densification of ultrafine precursor powder by mitigating the prevailing bi-axial constraining stress of the rigid substrate with numerous local multi-axial stress fields around them. In particular, adding 5 vol% YSZ nanoparticles resulted in a dense and uniform thin film electrolyte with narrow grain size distribution, and fine residual pores in isolated state. The thin film YSZ electrolyte placed on a rigid anode substrate with the GDC (gadolinia-doped ceria) and LSC (La_0.6Sr_0.4CoO_3?δ) layers deposited by PLD (pulsed laser deposition) processes revealed that it had fairly good gas tightness relevant to a SOFC (solid oxide fuel cell) electrolyte and maintained its structural integrity during fabrication and operation processes. In fact, the open circuit voltage was 1.07 V and maximum power density was 425 mW/cm² at 600 °C, which demonstrates that the chemical solution route can be a viable means for reducing electrolyte thickness for low- to intermediate-temperature SOFCs.     

Electrochemical Performance of Nd1.95NiO4+δ Cathode supported Microtubular Solid Oxide Fuel Cells

Nd_1.95NiO_4+δ (NNO) cathode supported microtubular cells were fabricated and characterized. This material presents superior oxygen transport properties in comparison with other commonly used cathode materials. The supporting tubes were fabricated by cold isostatic pressing (CIP) using NNO powders and corn starch as pore former. The electrolyte (GDC, gadolinia doped ceria based) was deposited by wet powder spraying (WPS) on top of pre‐sintered tubes and then co‐sintered. Finally, a NiO/GDC suspension was dip‐coated and sintered as the anode. Optimization of the cell fabrication process is shown. Power densities at 750 °C of ∼40 mWcm⁻² at 0.5V were achieved. These results are the first electrochemical measurements reported using NNO cathode‐supported microtubular cells. Further developments of the fabrication process are needed for this type of cells in order to compete with the standard microtubular solid oxide fuel cells (SOFC).     

Development of solid oxide cells by co-sintering of GDC diffusion barriers with LSCF air electrode

The effects of a Cu-based additive and nano-Gd-doped ceria (GDC) sol on the sintering temperature for the construction of solid oxide cells (SOCs) were investigated. A GDC buffer layer with 0.25–2 mol% CuO as a sintering aid was prepared by reacting GDC powder and a CuN₂O₆ solution, followed by heating at 600 °C. The sintering of the CuO-added GDC powder was optimized by investigating linear shrinkage, microstructure, grain size, ionic conductivity, and activation energy at temperatures ranging from 1000 to 1400 °C. The sintering temperature of the CuO–GDC buffer layer was decreased from 1400 °C to 1100 °C by adding the CuO sintering aid at levels exceeding 0.25 mol%. The ionic conductivity of the CuO–GDC electrolyte was maximized at 0.5 mol% CuO. However, the addition of CuO did not significantly affect the activation energy of the GDC buffer layer. Buffer layers with CuO-added GDC or nano-GDC sol-infiltrated GDC were fabricated and tested in co-sintering (1050 °C, air) with La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF). In addition, SOC tests were performed using button cells (active area: 1 cm²) and five-cell (active area: 30 cm²/cell) stacks. The button cell exhibited the maximum power density of 0.89 W cm⁻² in solid oxide fuel cell (SOFC) mode. The stack demonstrated more than 1000 h of operation stability in solid oxide electrolysis cell (SOEC) mode (decay rate: 0.004%/kh).     

Performance of IT‐SOFC with Ce0.9Gd0.1O1.95 Functional Layer at the Interface of Ce0.9Gd0.1O1.95 Electrolyte and Ni‐Ce0.9Gd0.1O1.95 Anode

In this paper we present results for a high power density IT‐SOFC and a method for dispersing nanosized Ce_0.9Gd_0.1O_1.95 (GDC) particles at the GDC electrolyte and Ni‐GDC anode interface. Dispersed nanosized particles were deposited to form an anode functional layer (AFL). Anode supports were prepared by tape casting of large micron‐sized NiO powder and sub micron‐sized GDC powder without pore former. For the cathode a La_0.6Sr_0.4Co_0.2Fe_0.8O_{3 – δ} (LSCF)‐GDC composite was used. Without an AFL the open circuit potential (OCP) and the maximum power density were 0.677 V and 407 mW cm^–2, respectively, at 650 °C using 30 sccm of hydrogen and air flow‐rate. With an AFL the OCP and the maximum power density increased to 0.796 V and 994 mW cm^–2, respectively, at the same temperature. Two point probe impedance measurements revealed that the AFL fabricated by the proposed method not only increased the OCP but also reduced the electrode polarisation by 68%. The effect of gas flow‐rate is also present in this paper. When hydrogen and air flow‐rate is increased to 90 sccm, the sample with AFL obtained 1.57 W cm^–2 at 650 °C.     

Application of a thin intermediate cathode layer prepared by inkjet printing for SOFCs

The application of an inkjet printing process for fabricating solid oxide fuel cell (SOFC) cathodes was investigated. Stably-dispersed LSCF–GDC inks were prepared by ball milling, and the composition was easily controlled by the preparation process. Fabrication of an LSCF–GDC layer was successfully carried out by depositing dots and the thickness was easily controlled by repeating printing process. A planar SOFC single cell with a double-layered cathode (comprised of a paste painted cathode layer and an inkjet printed interlayer) achieved a maximum power density of 0.71 W/cm² at 600 °C. This is the preliminary work for fabricating the cathode layer of a SOFC single cell via inkjet printing.     

Robust and reliable solid oxide fuel cells with modified thin film YSZ electrolyte

Reduce electrolyte thickness can improve solid oxide fuel cell (SOFC) performance. However, thinner electrolyte often contains prominent defects and flaws, which may decrease the yield and increase operation risk. This work proposes a method to modify the thin film YSZ electrolyte, to improve cell reliability and durability. The as-sintered anode supported half-cell with screen printed YSZ electrolyte was immersed in precursor solution of Y(NO₃)₃·6H₂O and Zr(NO₃)₄·5H₂O, and being treated under hydrothermal condition of 150°C for 12 h. As a result, the modified cells show slight increase in the OCV values. Furthermore, the hydrothermal modification effectively promotes interface sintering between YSZ electrolyte and GDC barrier layer, yielding a smaller ohmic resistance of .142 Ω·cm² (a decrease of ∼11%) and a higher peak power density of .964 W/cm² (an increase of ∼18%) at 750°C, than pristine cell. Moreover, the modified cell operates stably over 300 h, while the pristine cell presents large and irregular voltage fluctuations. This work suggests that the hydrothermal modification is an effective and promisingly industrial applicable method for thin film electrolyte recovery in SOFCs.     

Preliminary Study on Direct Operation of LT‐SOFCs Based on GDC Electrolyte Film With DME Fuel

Direct operation of anode‐supported cone‐shaped tubular low temperature solid oxide fuel cells (LT‐SOFCs) based on gadolinia‐doped ceria (GDC) electrolyte film with dimethyl ether (DME) fuel was preliminarily investigated in this study. The single cell exhibited maximum power densities of 500 and 350 mW cm^–2 at 600 °C using moist hydrogen and DME as fuel, respectively. A durability test of the single NiO‐GDC/GDC/LSCF‐GDC cell was performed at a constant current of 0.1 A directly fuelled with DME for about 200 min at 600 °C. The results indicate that the single cell coking easily directly operated in DME fuel. EDX result shows a clear evidence of carbon deposition in the anode. Further studies are needed to develop the novel anti‐carbon anode materials, relate the carbon deposition with anode microstructure and cell‐operating condition.