High-temperature dielectric and electromagnetic interference shielding properties of SiCf/SiC composites using Ti3SiC2 as inert filler

Ti₃SiC₂ filler has been introduced into SiC_f/SiC composites by precursor infiltration and pyrolysis (PIP) process to optimize the dielectric properties for electromagnetic interference (EMI) shielding applications in the temperatures of 25–600 °C at 8.2–12.4 GHz. Results indicate that the flexural strength of SiC_f/SiC composites is improved from 217 MPa to 295 MPa after incorporating the filler. Both the complex permittivity and tan δ of the composites show obvious temperature-dependent behavior and increase with the increasing temperatures. The absorption, reflection and total shielding effectiveness of the composites with Ti₃SiC₂ filler are enhanced from 13 dB, 7 dB and 20 dB to 24 dB, 21 dB and 45 dB respectively with the temperatures increase from 25 °C to 600 °C. The mechanisms for the corresponding enhancements are also proposed. The superior absorption shielding effectiveness is the dominant EMI shielding mechanism. The optimized EMI shielding properties suggest their potentials for the future shielding applications at temperatures from 25 °C to 600 °C.     

Segregated poly(vinylidene fluoride)/MWCNTs composites for high-performance electromagnetic interference shielding

Conductive polymer composites (CPCs) that contain a segregated structure have attracted significant attentions because of their promising for fulfilling low filler contents with high electromagnetic interference (EMI) properties. In the present study, segregated poly(vinylidene fluoride) (PVDF)/multi-walled carbon nanotubes (MWCNTs) composites were successfully prepared by mechanical mixing and hot compaction. The PVDF/MWCNTs samples with 7 wt% filler content possess high electrical conductivities and high EMI shielding effectiveness (SE), reaching 0.06 S cm⁻¹ and 30.89 dB (in the X-band frequency region), much higher than lots of reported results for CNT-based composites. And the EMI SE greatly increased across the frequency range as the sample thickness was improved from 0.6 to 3.0 mm. The EMI shielding mechanisms were also investigated and the results demonstrated absorption dominating shielding mechanism in this segregated material. This effective preparation method is simple, low-cost, and environmentally-friendly and has potential industrial applications in the future.     

Reduced graphene oxide deposited carbon fiber reinforced polymer composites for electromagnetic interference shielding

Reduced graphene oxide deposited carbon fiber (rGO-CF) was prepared by introducing GO onto CF surface through electrophoretic deposition method, following by reducing the GO sheets on CF with NaBH₄ solution. The rGO-CF was found to be more effective than CF to improve the electromagnetic interference (EMI) shielding property of unsaturated polyester (UP) based composites. With 0.75% mass fraction of rGO-CF, the shielding effectiveness of the composite reached 37.8 dB at the frequency range of 8.2–12.4 GHz (x-band), which had 16.3% increase than that of CF/UP composite (32.5 dB) in the same fiber mass fraction. The results suggest that rGO-CF is a good candidate for the use as a light-weight EMI shielding material.     

New electromagnetic wave shielding effectiveness at microwave frequency of polyvinyl chloride reinforced graphite/copper nanoparticles

A novel functional nanoconducting composite from polyvinyl chloride reinforced graphite–copper nanoparticles (PVC/GCu) was fabricated in order to produce a material suitable for electromagnetic interference (EMI) shielding applications. The microstructure of the nanocomposites was investigated by means of scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The thermal stability of the nanocomposites could improved with the incorporation of GCu nanoparticles. The electrical conductivity increases with increasing GCu content within composites. The percolation threshold of composites is low of about 2 wt.%. Hall-effect studies indicate that increase in GCu content in the composites causes increase in carrier concentration, mobility of the carriers and the composites behave as n-type semiconductor. The nanocomposites showed a high dielectric constant and a high dissipation factor in the frequency range of 1–20 GHz which makes it useful in charge storing and decoupling capacitors applications. The EMI shielding effectiveness (SE) of the PVC/GCu nanocomposites was tested over a frequency range of 1–20 GHz, and 22–70 dB shielding efficiency was obtained for the composites, suggesting that they may be used as an effective lightweight EMI shielding material in aerospace and radar evasion applications.     

Graphene foam/carbon nanotube/poly(dimethyl siloxane) composites for exceptional microwave shielding

Highly porous poly(dimethyl siloxane) (PDMS) composites containing cellular-structured microscale graphene foams (GFs) and conductive nanoscale carbon nanotubes (CNTs) are fabricated. The unique three-dimensional, multi-scale hybrid composites with inherent percolation and a high porosity of 90.8% present a remarkable electromagnetic interference shielding effectiveness (EMI SE) of ∼75 dB, a 200% enhancement against 25 dB of the composites made from GFs alone with the same graphene content and porosity. The corresponding specific EMI SE measured against the composite density is 833 dB cm³/g. These values are among the highest for all carbon filler/polymer composites reported thus far. Significant synergy arises from the hybrid reinforcement structure of the composites: the GFs drive the incident microwaves to be attenuated by dissipation of the currents induced by electromagnetic fields, while the CNTs greatly enhance the dissipation of surface currents by expanding the conductive networks and introducing numerous interfaces with the matrix.     

Enhanced thermal conductivity and dielectric properties of Al/β-SiCw/PVDF composites

Polymeric composites with high thermal conductivity, high dielectric permittivity but low dissipation factor have wide important applications in electronic and electrical industry. In this study, three phases composites consisting of poly(vinylidene fluoride) (PVDF), Al nanoparticles and β-silicon carbide whiskers (β-SiC_w) were prepared. The thermal conductivity, morphological and dielectric properties of the composites were investigated. The results indicate that the addition of 12 vol% β-SiC_w not only improves the thermal conductivity of Al/PVDF from 1.57 to 2.1 W/m K, but also remarkably increases the dielectric constant from 46 to 330 at 100 Hz, whereas the dielectric loss of the composites still remain at relatively low levels similar to that of Al/PVDF at a wider frequency range from 10⁻¹ Hz to 10⁷ Hz. With further increasing the β-SiC_w loading to 20 vol%, the thermal conductivity and dielectric constant of the composites continue to increase, whereas both the dielectric loss and conductivity also rise rapidly.     

Short shaped copper fibers in an epoxy matrix: Their role in a multifunctional composite

Previous research indicates that short shaped copper fibers improve the fracture and impact toughness of brittle thermoset polymer matrix composites. This paper investigates the potential multifunctional ability of these same shaped copper fibers by determining their electromagnetic interference (EMI) shielding effectiveness (SE). Fiber shapes were selected based on previous single fiber pullout experiments where they displayed high toughness. The two fiber diameters tested were: 0.325 and 0.162 mm. Fiber shapes used in the experiments were: straight, flat end-impacted, rippled, and acid roughened. A SE of greater than 45 dB at 1.0 GHz was attained in epoxy that contained 15 vol% of 0.162 mm diameter shaped fibers. Composites with 15 vol% of the 0.325 mm diameter shaped fibers showed poor SE, less than 20 dB. Experimental results indicate that besides improving the fracture and impact toughness of a thermoset polymer matrix, short shaped copper fibers can also significantly improve the SE and electrical conductivity of the composite, resulting in a multifunctional material. This increase in SE and electrical conductivity can be attributed to: shape effects that increase the skin volume, surface discontinuities which increase the amount of electromagnetic (EM) wave scattering, and the fiber count which determines the number of conducting paths.     

Designing of carbon nanotube/polymer composites using melt recirculation approach: Effect of aspect ratio on mechanical,electrical and EMI shielding response

The paper describes the effect of aspect ratio of multiwall carbon nanotubes (MCNTs) on the electrical, mechanical and electromagnetic properties of polypropylene random copolymer (PPC). Long and short MCNTs with aspect ratio of ~ 1356–1937 and ~ 158 respectively were melt-blended with PPC in a micro twin screw extruder with melt recirculation that allow the formation of composites having ~ 15 wt.% MCNTs. The good dispersion was confirmed by scanning electron microscopy and observation of electrical conductivity at low percolation threshold (0.45 and 1.07 wt.% for l- & s-MCNT/PPC composite respectively) and improvement of modulus and strength. The 15 wt.% l-MCNTs and s-MCNT loaded composites show 52% and 60% improvement in modulus respectively and 20% & 18% improvement in strength over neat PPC. The electromagnetic interference (EMI) shielding response (in 8.2–12.4 GHz frequency range) revealed that l-MCNT based PPC composites display better shielding at lower loading (up to 4 wt.%) while s-MCNT show better attenuation at higher loadings. The realization shielding effectiveness value of − 27 dB (> 99% attenuation) respectively for l-MCNT composites: and − 37 dB (> 99.9% attenuation) for s-MCNTs composites at 15 wt.% reflect their potential for making light weight and structurally strong EMI shields.     

MWNT/PEG grafted nanocomposites and an analysis of their EMI shielding properties

EMI shielding films made from carbon nanotube grafted with organic polymers at a low cost have been developed. MWCNTs exhibit desirable electrical properties for EMI shielding films. In this study, PEG was employed by urethane bonding to increase the processability and dispersibility of the MWCNTs. The molecular weight of PEG was 200 and 2000, and their EMI shielding films were fabricated by addition of UV-curing photoinitiator. The EMI shielding property was measured, and they show proper EMI reflectance and shielding effectiveness. Especially, when 4.0 wt% of MWCNTs were added to PEG with a molecular weight of 200 g/mol, it exhibited the maximum EMI SE value was ?22.9 dB at 4.14 GHz, while the average EMI SE value which was ?20.53 dB.     

Investigation of electrical conductivity and electromagnetic shielding effectiveness of polyaniline composite

With the increasing of electromagnetic pollution and the widely use of commercial and military products, there is an increasing interest in electromagnetic interference (EMI) shielding. This paper mainly aims at electrical conductivity and EMI shielding effectiveness (SE) of the conducting composites made from silicone rubber (SR) with different loading levels of HCl-doped polyaniline (PAN-HCl) in the low frequency range from 3 to 1500 MHz. The result indicates that SE of the composites increase and the volume resistivity decrease with increasing mass ratio loading of PAN-HCl in the SR. The measured SE of the composites are from 16 to 19.3 dB at 100 mass ratio loading of the PAN-HCl and the volume resistivity decrease nine orders of magnitude compared with that of the emeraldine base form of PAN (PAN-EB) composites.     

Synthesis of conducting ferromagnetic nanocomposite with improved microwave absorption properties

The present paper reports the synthesis of polyaromatic amine–ferromagnetic composite with nanosize TiO₂ (～70–90 nm) and γ-Fe₂O₃ (～10–15 nm) particles via in situ emulsion polymerization. Magnetic and conductivity studies demonstrate that the conducting ferromagnetic composite possesses saturation magnetization (M_S) value of 26.9 emu g^?1 and conductivity of the order of 0.46 S cm^?1, which are measured by vibrating sample magnetometer and four-probe technique, respectively. It is observed that the presence of the nanosized γ-Fe₂O₃ in the polyaniline–TiO₂ matrix affects the electromagnetic shielding property of the composite. Polyaniline–TiO₂–γ-Fe₂O₃ nanocomposite has shown better shielding effectiveness due to absorption (SE_A ～ 45 dB) than the polyaniline-γ-Fe₂O₃ (SE_A ～ 8.8 dB) and polyaniline–TiO₂ (SE_A ～ 22.4 dB) nanocomposite. The polymer composites were further characterized by high resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD) technique.     

Dielectric,mechanical and thermal properties of polymer/BaTiO3 composites for embedded capacitor

Barium titanate (BaTiO₃) filled polymethylmethacrylate (PMMA) composites were prepared using the simple solution method followed by hot pressing. The content of BaTiO₃ was varied from 0 to 65 vol.%. Scanning electron microscopy showed good dispersion and adhesion of BaTiO₃ with the PMMA matrix. The dielectric constant of the composites increased significantly. There was weak dispersion in the dielectric constant of the composites (up to 45 vol.%) with frequency between 100 Hz and 15 MHz. The dissipation factor of the composites increased from 0.021 for pure PMMA to 0.029 for 45 vol.% composites. However, 65 vol.% composite showed dispersion in dielectric constant with increasing frequency and higher dissipation factor. The Lichtenecker equation agreed well with the experimental data. The microhardness and the glass transition temperature of the composites increased approximately 4.7-fold and 42 °C, respectively, compared to pure PMMA. The CTE of the 65 vol.% composite is close to that of copper.     

Development of electromagnetic shielding materials from the conductive blends of polyaniline and polyaniline-clay nanocomposite-EVA: Preparation and properties

Electromagnetic interference shielding composite materials were developed from the conductive blends of nanostructured polyaniline (PANI) and polyaniline-clay nanocomposite (PANICN) with ethylene vinyl acetate (EVA) as host matrix. Electrically conducting nanostructured PANI and PANICNs were prepared using amphiphilic dopants, 3-pentadecyl phenol 4-sulphonic acid (3-PDPSA) derived from cashew nut shell liquid, a low cost renewable resource based product and dodecyl benzene sulfonic acid (DBSA). Effects of type and quantity of conductive fillers on the electrical conductivity, mechanical properties, thermal stability, morphology and electromagnetic shielding efficiency were investigated. The presence of exfoliated nanoclay and interaction between the conductive filler–host matrix in conductive films containing PANICNs manifested from the measurement on rheological property. Films with conductive filler (～15% loading) showed a shielding effectiveness of ～40–80 dB at 8 GHz which makes these conducting composites potential candidate for the encapsulation as EMI shielding materials for electronic devices.     

Electromagnetic interference shielding of composites consisting of a polyester matrix and carbon nanotube-coated fiber reinforcement

We investigated the electromagnetic interference shielding effectiveness (EMI SE) of composites consisting of an unsaturated polyester matrix containing woven glass or carbon fibers that had been coated with multiwalled carbon nanotubes (MWCNTs). Composite panels consisting of fiber fabrics with various combinations of fabric type and stacking sequence were fabricated. Their EMI SE was measured in the frequency range of 30 MHz–1.5 GHz. The underlying physics governing the EMI shielding mechanisms of the materials, namely, absorption, reflection, and multiple reflections, was investigated and used in analytical models to predict the EMI SE. Simulation and experimental results showed that the contributions of reflection and absorption to EMI shielding is enhanced by sufficient impedance mismatching, while multiple reflections have a negative effect. For a given amount of MWCNTs in the glass-fiber–reinforced composite, coating the outermost, instead of intermediate, glass fiber plies with MWCNTs was found to maximize the conductivity and SE.     

Development of electromagnetic shielding materials from the conductive blends of polystyrene polyaniline-clay nanocomposite

Electromagnetic interference shielding composite materials were developed from the conductive blends of nanostructured polyaniline-clay composite (PANICN) and Polystyrene (PS) by a one step host matrix assisted emulsion polymerization of anilinium salt of 3-pentadecyl phenol-4-sulphonic acid (3-PDPSA) in clay. 3-PDPSA was derived from cashew nut shell liquid, a low cost renewable resource based product. These blends were characterized using Uv–visible and FT-IR spectroscopy, XRD, electrical conductivity, thermal property, dielectric property and electromagnetic shielding efficiency. The interactions between the primary particles and host matrix were elucidated from the studies made through spectroscopy and rheology. The key finding of the research is that this low cost PANICNPS blend with superior electrical conductivity (7.6 × 10^?1 S/m), excellent thermal stability and EMI SE of 10–20 dB at 8 GHz makes them as a promising candidate for application in EMI shielding and antistatic discharge matrix for the encapsulation of micro electronic devices.     

Influence of adsorbed moisture on the properties of cyanate ester/BaTiO3 composites

The effect of moisture adsorbed on BaTiO₃ on the properties of cyanate ester (CE)/BaTiO₃ dielectric composites is examined using undried and dried BaTiO₃ particles. The influence of moisture on the dielectric constant, thermal stability, dynamic mechanical properties, flexural behavior and micro morphology of the composites is investigated. Dielectric constant (ε) and dielectric loss (tan δ) of composites with the dried BaTiO₃ are both higher than composites manufactured with undried filler at the same frequency. The dielectric properties of the dried system are stable over a broader temperature range than the undried composites. Adsorbed moisture causes the initial decomposition temperature and the maximum degradation temperature of the composite to decrease by 27 °C and 15 °C, respectively. By removing the moisture from BaTiO₃, the CE/BaTiO₃ composite exhibits a lower modulus (E′), higher strength, higher flexural elongation and a dramatically increased glass transition temperature (T_g).     

Electromagnetic shielding effectiveness of aluminum alloy–fly ash composites

The cenosphere and precipitator fly ash particulates were used to produce two kinds of aluminum matrix composites with the density of 1.4–1.6 g cm⁻³ and 2.2–2.4 g cm⁻³ separately. The electromagnetic interference shielding effectiveness (EMSE) properties of the composites were measured in the frequency range of 30.0 kHz–1.5 GHz. The results indicated the EMSE properties of the two types of composites were nearly the same. By using the fly ash particles, the shielding effectiveness properties of the matrix aluminum have been improved in the frequency ranges 30.0 kHz–600.0 MHz and the increment varied with increasing frequency. The EMSE properties of 2024Al are in the range −36.1 ± 0.2 to −46.3 ± 0.3 dB while the composites are in the range −40.0 ± 0.8 to −102.5 ± 0.1 dB in the frequency range 1.0–600.0 MHz. At higher frequency, the EMSE properties of the composites are similar to that of the matrix. The tensile strength of the matrix aluminum has been decreased by addition of the fly ash particulate and the tensile strength of the composites were 110.2 MPa and 180.6 MPa separately. The fractography showed that one composite fractured brittly and the other fractured in a microductile manner.     

Complex permittivity and electromagnetic interference shielding properties of Ti<Subscript>3</Subscript>SiC<Subscript>2</Subscript>/polyaniline composites

Ti₃SiC₂/insulating polyaniline (Ti₃SiC₂/PANI) composites were prepared by solution blending and subsequently by hot-pressing process. The dielectric permittivity and electromagnetic interference (EMI) shielding effectiveness (SE) of the composites were determined in the frequency range of 8.2–12.4 GHz (X-band). Both real and imaginary permittivities increase with the increasing Ti₃SiC₂ content, and which are attributed to the enhanced displacement current and conduction current. The EMI SE of the composites can be greatly improved by addition of Ti₃SiC₂ filler, which may be ascribed to the increase of electrical conductivity of the composites. It is also found that the reflection of electromagnetic radiation is a dominant mechanism for EMI shielding of the composite. An average EMI SE of 23 dB can be achieved in the X-band range for the composite with 25 wt% Ti₃SiC₂ content, which shows the potential of the Ti₃SiC₂/PANI composites as EMI shielding materials for commercial applications.     

Porous composites coated with hybrid nano carbon materials perform excellent electromagnetic interference shielding

This work reported preparation of porous composites using a simple dip-coating method, and the fabricated composites containing hybrid carbon nanomaterials performed excellent electromagnetic interference (EMI) shielding properties. A commercial sponge was coated with silver nanoparticles before being dip-coated with graphene (GP)/ink, multi-wall carbon nanotubes (MWCNTs)/ink, or hybrid GP/MWCNTs/ink to form Ag/carbon nanomaterial hybrid composites, and then the composites were subjected to EMI measurements in the frequency range of 0.45–1.5 GHz. For comparison, the sponges without Ag nanoparticle coating were also prepared. Herein, we found an insignificant difference in EMI SE among the porous composites without Ag nanoparticle coating, and the maximum values of approximately 14.4 dB was attained. Interestingly, the hybrid composites with Ag nanoparticle coating exhibited maximum EMI shielding of 24.33 dB. Due to their porous structure, the EMI SE measurements showed that reflection dominates the EMI SE for all the sponge composites studied in this work.     

Effect of heat treatment on electromagnetic shielding effectiveness of ZK60 magnesium alloy

Electromagnetic interference (EMI) shielding capacity of ZK60 magnesium alloy in different heat treatment conditions was investigated in the testing frequency range of 30–1500 MHz. EMI shielding effectiveness (SE) was measured by coaxial cable method at ambient temperature. Experimental results indicate that solid solution treatment enhances the SE of as-extruded ZK60 alloy at low frequency, while has an inverse effect on the SE at high frequency. Artificial aging treatment following solid solution improves shielding capacity obviously, moreover the SE value of the alloy increase gradually with increasing amount of second phase precipitates. Solution treatment at 400 °C for 5 h plus artificial aging at 170 °C for 25 h is determined as the optimum heat treatment condition. In this condition, a high shielding effectiveness of 62–75 dB has been attained in the alloy, which is greatly higher than the value in extruded state. The above-mentioned observations were analyzed in terms of microstructural variation, especially solid solution and precipitation of alloying elements in ZK60 alloy in details.