Structure and AC conductivity of nanocrystalline Yttrium oxide thin films

Yttrium oxide (Y₂O₃) thin films were grown at substrate temperatures (T_s) ranging from room temperature (RT) to 500 °C and their structural and electrical properties were evaluated. The results indicate that Y₂O₃ films grown at RT-100 °C were amorphous (a-Y₂O₃). Y₂O₃ films began to show cubic phase (c-Y₂O₃) at T_s = 200 °C. The average grain size varies from 5 to 40 nm as a function of T_s. Room temperature ac electrical conductivity increases from 0.4 (Ω-m)^− 1 to 1.2 (Ω-m)^− 1 with increasing T_s from RT to 500 °C. The frequency dispersion of the electrical resistivity reveals the hopping conduction mechanism. Frequency dispersion of the electrical resistivity fits to the modified Debye's function, which considers more than one ion contributing to the relaxation process. The mean relaxation time decreases from 2.8 to 1.4 μs with increasing T_s indicating that the effect of microstructure of the Y₂O₃ films is significant on the electrical properties.     

Spray pyrolysis deposition of indium sulphide thin films

In₂S₃ thin films were grown by the chemical spray pyrolysis (CSP) method using the pneumatic spray set-up and compressed air as a carrier gas. Aqueous solutions containing InCl₃ and SC(NH₂)₂ at a molar ratio of In/S = 1/3 and 1/6 were deposited onto preheated glass sheets at substrate temperatures T_s = 205-410 °C. The obtained films were characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM,) optical transmission spectra, X-ray photoelectron spectroscopy (XPS) and energy dispersive spectroscopy (EDS). According to XRD, thin films deposited at T_s = 205-365 °C were composed of the (0 0 12) orientated tetragonal β-In₂S₃ phase independent of the In/S ratio in the spray solution. Depositions performed at T_s = 410 °C led to the formation of the In₂O₃ phase, preferably when the 1/3 solution was sprayed. Post-deposition annealing in air indicated that oxidation of the sulphide phase has a minor role in the formation of In₂O₃ at temperatures up to 450 °C. In₂S₃ films grown at T_s below 365 °C exhibited transparency over 70% in the visible spectral region and E_g of 2.90-2.96 eV for direct and 2.15-2.30 eV for indirect transitions, respectively. Film thickness and chlorine content decreased with increasing deposition temperatures. The XPS study revealed that the In/S ratio in the spray solution had a significant influence on the content of oxygen (Me-O, BE = 530.0 eV) in the In₂S₃ films deposited in the temperature range of 205-365 °C. Both XPS and EDS studies confirmed that oxygen content in the films deposited using the solution with the In/S ratio of 1/6 was substantially lower than in the films deposited with the In/S ratio of 1/3.     

Structural and optical studies of nanocrystalline V2O5 thin films

We report the structural and optical properties of nanocrystalline thin films of vanadium oxide prepared via evaporation technique on amorphous glass substrates. The crystallinity of the films was studied using X-ray diffraction and surface morphology of the films was studied using scanning electron microscopy and atomic force microscopy. Deposition temperature was found to have a great impact on the optical and structural properties of these films. The films deposited at room temperature show homogeneous, uniform and smooth texture but were amorphous in nature. These films remain amorphous even after postannealing at 300 °C. On the other hand the films deposited at substrate temperature T_S > 200 °C were well textured and c-axis oriented with good crystalline properties. Moreover colour of the films changes from pale yellow to light brown to black corresponding to deposition at room temperature, 300 °C and 500 °C respectively. The investigation revealed that nanocrystalline V₂O₅ films with preferred 001 orientation and with crystalline size of 17.67 nm can be grown with a layered structure onto amorphous glass substrates at temperature as low as 300 °C. The photograph of V₂O₅ films deposited at room temperature taken by scanning electron microscopy shows regular dot like features of nm size.     

Composition dependence of optical constants in ferroelectric Ba(Ti1 − x,Nix)O3 thin films by optical transmittance technique

Ba(Ti_1 − x,Ni_x)O₃ ferroelectric thin films with perovskite structure are prepared on fused quartz substrates by a sol-gel process. Optical transmittance measurements indicate that Ni-doping has an obvious effect on the energy band structure of BaTiO₃. It has been found that the refractive index n, extinction coefficient k, and band gap energy E_g of the films are functions of the film composition. The E_g of Ba(Ti_1 − x,Ni_x)O₃ decreases approximately linearly as the Ni content increases, which is attributed to the decline of conduction band energy level with increasing the Ni content. On the other hand, n and k both increase linearly with increasing the Ni content because of the increase of packing density. These results indicate that thin films might have potential applications in BaTiO₃-based thin-film optical devices.     

Distribution of pyrochlore phase in Pb(Mg1/3Nb2/3)O3-PbTiO3 films and suppression with a Pb(Zr0.52Ti0.48)O3 interfacial layer

Thin films of the relaxor ferroelectric Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) on Pt/Ti/SiO₂/Si (Pt/Si) substrates both with and without a Pb(Zr_0.52Ti_0.48)O₃ (PZT) interfacial layer were investigated. Perovskite and pyrochlore coexistence was observed for PMN-PT thin films without a PZT interfacial layer. Interestingly, most of the pyrochlore phase was observed in single-coated films and in the first layer of multi-coated films. The pyrochlore phase exhibited grains with an average size of about 25 nm, which is smaller than those of the perovskite phase (about 90 nm). In contrast, for PMN-PT thin films grown on a PZT interfacial layer, the formation of a pyrochlore phase at the interface between PMN-PT layers and the substrate is completely suppressed. Moreover, small grains are not observed in the films with a PZT interfacial layer. The measured polarization-electric field (P-E) hysteresis loops of PMN-PT films with and without PZT layers indicate that enhanced electrical properties can be obtained when a PZT interfacial layer is used. These enhanced properties include an increase in the value of remanent polarization P_r from 2.7 to 5.8 μC/cm² and a decrease in the coercive field E_c from 60.5 to 28.0 kV/cm.     

Structural and optical analysis of nanocrystalline thin films of mixed rare earth oxides (Y1-xErx)2O3

Nanocrystalline thin films of mixed rare earth oxides (Y_1-xEr_x)₂O₃(0.1 ≤ x ≤ 1) were deposited by electron beam evaporation technique on polished fused silica glass at different substrate temperatures (200-500 °C). The effect of the substrate temperature as well as the mixing parameter (x) on the structural and optical properties of these films has been investigated by using X-ray diffraction (XRD), energy dispersive x-ray analysis and optical spectrophotometry. XRD investigation shows that mixed rare earth oxides film (Y_1-xEr_x)₂O₃ grown at lower substrate temperature (T_s ≤ 300 °C) are poorly crystalline, whereas films grown at higher substrate temperatures (T_s ≥ 400 °C) tend to have better crystallinity. Furthermore, the mixing parameter (x) was found to stabilize the cubic phase over the entire of 0.1 ≤ x ≤ 1. The crystallite size of the films was found to vary in the range from 25 to 39 nm. Optical band gap of the films was deterimined by analysis of the absoprtion coeffifcient. For films deposited at different substrate temperatures direct and indirect transitions occur with energies varied from 5.29 to 5.94 eV and from 4.23 to 4.51 eV, respectively. However, films of different composition x, give optical band gap varied from 6.14 to 5.86 eV for direct transition and from 5.23 to 4.22 eV for indirect transitions. Consequently, one may conclude that it is possible to tune the energy band gap by relative fraction of constituent oxides. It was found that optical constants increase with increasing the substrate temperature. Nevertheless, the values of n and k decrease with increasing the mixing parameter, x.     

Properties of La-substituted Na0.5Bi4.5Ti4O15 ferroelectric thin films

Ferroelectric Na_0.5La_0.5Bi₄Ti₄O₁₅ (NaLaBTi) thin films were prepared by a chemical solution deposition method. The NaLaBTi thin films annealed at 750 °C under oxygen atmosphere were randomly oriented polycrystalline. Electrical properties of the NaLaBTi thin films were compared to Na_0.5Bi_4.5Ti₄O₁₅ thin films and better properties were observed in the NaLaBTi thin films. Remnant polarization (2P_r) and coercive electric field (2E_c) were 43 µC/cm² and 204 kV/cm at an applied electric field of 478 kV/cm, respectively. Leakage current density was 1.95 × 10^− 6 A/cm² at 100 kV/cm. Dielectric constant and dielectric loss were 805 and 0.05 at 1 kHz, respectively. Switchable polarization was suppressed by 15% after 1.44 × 10¹⁰ switching cycles.     

Structural and magnetic properties of CoFe2O4 thin films deposited by laser ablation on Si (001) substrates

Cobalt ferrite (CoFe₂O₄) thin films have been deposited on Si (001) substrates, with different substrate temperatures (T_dep = 25 °C − 600 °C). The films were prepared by pulsed laser ablation with a KrF excimer laser (wavelength λ = 248 nm). The oxygen pressure during deposition was 2 × 10⁻² mbar. The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low deposition temperatures, the films presented a mixture of a CoFe₂O₄ phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the deposition temperature increased, the CoO and FeO relative content strongly decreased, so that for T_dep = 600 °C the films were composed mainly by polycrystalline CoFe₂O₄. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field (H_exch) originated by the presence of the antiferromagnetic phases. The exchange field decreased with increasing deposition temperature, and was accompanied by a corresponding increase of the coercivity and remanence ratio of the cycles. This behavior was due to the strong reduction of the CoO and FeO content, and to the corresponding dominance of the CoFe₂O₄ phase on the magnetic properties of the thin films.     

Structural,optical and electrical properties of In4Sn3O12 films prepared by pulsed laser deposition

Highly conducting (σ ∼ 2.6 × 10³ Ω⁻¹ cm⁻¹) In₄Sn₃O₁₂ films have been deposited using pulsed laser deposition (PLD) on glass and quartz substrates held at temperatures between 350 and 550 °C under chamber pressures of between 2.5 and 15 mTorr O₂. The crystallinity and the surface roughness of the films were found to increase with increasing substrate temperature. Electron concentrations of the order of 5 × 10²⁰ cm⁻³ and mobilities as high as 30 cm² V⁻¹ s⁻¹ were determined from Hall effect measurements performed on the films. Fitting of the transmission spectral profiles in the ultra-violet–visible spectrum has allowed the determination of the refractive index and extinction coefficient for the films. A red-shift in the frequency of plasmon resonance is observed with both increasing substrate temperature and oxygen pressure. Effective masses have been derived from the plasma frequencies and have been found to increase with carrier concentration indicating a non-parabolic conduction band in the material In₄Sn₃O₁₂. The optical band-gap has been determined as 3.8 eV from the analysis of the absorption edge in the UV. These results highlight the potential of these films as lower In-content functional transparent conducting materials.     

Fabrication of nanostructure Al2O3/ZrO2 (Y2O3) eutectic by combustion synthesis melt-casting under ultra-high gravity

A novel method for preparing Al₂O₃/ZrO₂ (Y₂O₃) eutectic was developed by combining combustion synthesis with melt-casting under ultra-high gravity (CSMC-UHG). The application of UHG = 800 g resulted in a high relative density of 99.8%, and an orientation-growth along the UHG direction. The microstructure was composed of aligned growth regimes containing a triangular dispersion of orderly ZrO₂ rods in Al₂O₃ matrix with a spacing of 300 nm. The eutectic had a high fracture toughness up to 17.9 MPa·m^1/2, which was mainly attributed to the nanostructure and the elastic bridge effects of the aligned ZrO₂ rods.     

Thin film preparation and characterization of wide band gap Cu3TaQ4 (Q = S or Se) p-type semiconductors

The structural, optical, and electronic properties of thin films of a family of wide band gap (E_g > 2.3 eV) p-type semiconductors Cu₃TaQ₄ (Q = S or Se) are presented. Thin films prepared by pulsed laser deposition of ceramic Cu₃TaQ₄ targets and ex-situ annealing of the as-deposited films in chalcogenide vapor exhibit mixed polycrystalline/[100]-directed growth on amorphous SiO₂ substrates and strong (100) preferential orientation on single-crystal yttria-stabilized zirconia substrates. Cu₃TaS₄ (E_g = 2.70 eV) thin films are transparent over the entire visible spectrum while Cu₃TaSe₄ (E_g = 2.35 eV) thin films show some absorption in the blue. Thin film solid solutions of Cu₃TaSe_4 − xS_x and Cu₃TaSe_4 − xTe_x can be prepared by annealing Cu₃TaSe₄ films in a mixed chalcogenide vapor. Powders and thin films of Cu₃TaS₄ exhibit visible photoluminescence when illuminated by UV light.     

Flame aerosol deposition and annealing of Y3Al5O12:Tb phosphor coatings

Sub-micrometer-sized powders of Y₃Al₅O₁₂:Tb phosphor (d_SEM = 320 nm) were prepared by flame-assisted spray pyrolysis of aqueous precursors in a premixed propane/air flame and in situ deposited onto quartz substrates. Phosphor screens with densities of up to 0.7 mg cm⁻² could be produced within 20 min. As-deposited coatings were amorphous and required a thermal post-treatment. After annealing in an oven for 2 h (T ≥ 900 °C), the yttrium aluminum garnet phase (YAG:Tb) was obtained. Alternatively, the phosphor coatings were treated by an impinging flame in the same setup used for the deposition. Quasi-amorphous Y₃Al₅O₁₂:Tb coatings demonstrated bright green photoluminescence upon flame annealing at T ≈ 1100 °C for just several minutes and could outperform YAG:Tb when excited in the wavelength ranges 205–220 nm and 230–260 nm. For example, brightness of emission from the quasi-amorphous coatings was up to five times higher than that of the fully crystalline YAG:Tb phosphor at a technically important wavelength of 254 nm.     

Structural and thermal characterization of La5Ca9Cu24O41 thin films grown by pulsed laser deposition on (1 1 0) SrTiO3 substrates

In the present study stoichiometric, b-axis oriented La₅Ca₉Cu₂₄O₄₁ thin films were grown by pulsed laser deposition on (1 1 0) SrTiO₃ substrates in the temperature range 600-750 °C. High resolution transmission electron microscopy was employed to investigate the growth mechanism and the epitaxial relationship between the SrTiO₃ substrates and the La₅Ca₉Cu₂₄O₄₁ films grown at 700 °C. The 3-ω method was used to measure the cross-plane thermal conductivity of La₅Ca₉Cu₂₄O₄₁ films in the temperature range 50-350 K. The observed glass-like behavior is attributed to atomic-scale defects, grain boundaries and an interfacial layer formed between film and substrate.     

Tl2Ba2CaCu2O8 thin films on 2 in. LaAlO3(0 0 1) substrates

High quality Tl₂Ba₂CaCu₂O₈ (Tl-2212) superconducting thin films are prepared on both sides of 2 in. LaAlO₃(0 0 1) substrates by off-axis magnetron sputtering and post-annealing process. XRD measurements show that these films possess pure Tl-2212 phase with C-axis perpendicular to the substrate surface. The thickness unhomogeneity of the whole film on the 2 in. wafer is less than 5%. The superconducting transition temperatures T_cs of the films are around 105 K. At zero applied magnetic field, the critical current densities J_cs of the films on both sides of the wafer were measured to be above 2 × 10⁶ A/cm² at 77 K. The microwave surface resistance R_s of film was as low as 350 μΩ at 10 GHz and 77 K. In order to test the suitability of Tl-2212 thin films for passive microwave devices, 3-pole bandpass filters have been fabricated from double-sided Tl-2212 films on LaAlO₃ substrates.     

Effect of yttrium doping on the dielectric properties of CaCu3Ti4O12 thin film produced by chemical solution deposition

Pure and yttrium substituted CaCu₃Ti_4 − xY_xO_{12 − x / 2} (x = 0, 0.02, 0.1) thin films were prepared on boron doped silica substrate employing chemical solution deposition, spin coating and rapid thermal annealing. The phase and microstructure of the sintered films were examined using X-ray diffraction and scanning electron microscopy. Dielectric properties of the films were measured at room temperature using electrochemical impedance spectroscopy. Highly ordered polycrystalline CCTO thin film with bimodal grain size distribution was achieved at a sintering temperature of 800 °C. Yttrium doping was found to have beneficial effects on the dielectric properties of CCTO thin film. Dielectric parameters obtained for a CaCu₃Ti_4 − xY_xO_{12 − x / 2} (x = 0.02) film at 1 KHz were k ∼ 2700 and tan δ ∼ 0.07.     

Properties of screen-printed Ho-Ba-Cu-O films on YSZ substrates

High-T_c screen-printed Ho-Ba-Cu-O films were prepared on YSZ substrates by a melt processing method. The films were fired at T_s = 1000-1050 °C for 5 min and cooled to 450 °C by two steps in flowing O₂. The maximum critical current density J_c (77 K, 0 T) of 2.0 × 10³ A cm^− 2 was only attained under much limited firing conditions; T_s = 1020 °C and cooled to 800 °C at a cooling rate of 400 °C h^− 1.     

Structural and electrical properties of BiFeO3 thin films by solution deposition and microwave annealing

Lead-free polycrystalline BiFeO₃ (BFO) thin films were developed using a chemical solution deposition method to deposit the films and the multi-mode 2.45 GHz microwave furnace to optimize the annealing condition of the films. Phase-pure BFO films were obtained at 500 °C-600 °C for 1-5 min with a heating rate of 10 °C/min. The film by microwave annealing (MW) at 550 °C for 5 min exhibited a (012)-preferred orientation with a dense morphology of grain size ~ 294 nm. Its dielectric constant of 96.2, low leakage current density of 2.466 × 10^− 6 A/cm², polarization (2P_r) and coercive field (2E_c) of 0.931 μC/cm² and 57.37 kV/cm, respectively, were improved compared to those by conventional annealing (CA) at the same annealing conditions.     

Temperature shift of the optical gap in some PbO-ZnO-P2O5 glasses

The optical gap (E_g) between 4.54 eV-4.88 eV at room temperature was determined for PbO-ZnO-P₂O₅ glasses with the formal content of P₂O₅ in the region of 30 to 50 mol% and with the formal content of PbO in the region of 50 to 45 mol%, respectively. The temperature (T) dependence of the optical gap (E_g(T)) in the region 80 < T[K] < 600 was determined, and an electron-phonon interaction is suggested to be a major contribution to the temperature shift of the optical gap. In the temperature region of 300-600 K, the E_g(T) dependence can be approximated by a simple linear relation with the temperature coefficient (γ) of the optical gap in the region 6.04 ≤ γ × 10⁴ [eV/K] ≤ 7.39.     

Luminescence properties of Eu ions doped in Y2−xGdxO3 thin films grown by pulsed laser deposition method

Luminescence properties of Y_2−xGd_xO₃:Eu³⁺ (x = 0 to 2.0) thin films are investigated by site-selective laser excitation spectroscopy. The films were grown by pulsed laser deposition method on SiO₂ (100) substrates. Cubic phase Y₂O₃ and Gd₂O₃ and monoclinic phase Gd₂O₃ are identified in the excitation spectrum of the ⁷F₀ → ⁵D₀ transition of Eu³⁺. The emission spectra of the ⁵D₀ → ⁷F_J (J = 1 and 2) transition from individual Eu³⁺ centers were obtained by tuning the laser to resonance with each excitation line. The excitation line at around 580.60 nm corresponds to the line from Eu³⁺ with C₂ site symmetry of cubic phase. New lines at 578.65 and 582.02 nm for the C_S sites of Gd₂O₃ with monoclinic phase are observed by the incorporation of Gd in Y₂O₃ lattice. Energy transfer occurs between Eu³⁺ ions at the C_S sites and from Eu³⁺ ions at the C_S sites to those at the C₂ site in Y_2−xGd_xO₃.     

Effect of working pressure on the properties of BaTiO3-CoFe2O4 composite films deposited on STO (100) by PLD

The BaTiO₃-CoFe₂O₄ (BTO-CFO) composite films were grown on SrTiO₃ (STO) (100) substrates at 750 °C under various working pressures by pulsed laser deposition. The composite film grew into a supersaturated single phase at the working pressure of 10 mTorr, BTO and CFO (00 l) oriented hetero-epitaxial films on STO (100) at 100 mTorr, and a polycrystalline composite film at 500 mTorr. The slow growth rate at high working pressure led to the phase separation in the composite film. The CFO was compressively strained along out-of-plane due to the lattice mismatch with the BTO matrix phase. The BTO-CFO composite film grown at 100 mTorr showed reversible switching of ferroelectric polarization and magnetic hysteresis with strong magnetic anisotropy.