Nanocomposite fibers of poly(ethylene terephthalate) with montmorillonite and mica: thermomechanical properties and morphology

The thermal stabilities, mechanical properties, and morphologies of nanocomposites of poly(ethylene terephthalate) (PET) with two different organoclays are compared. Dodecyltriphenylphosphonium‐montmorillonite (C₁₂PPh‐MMT) and dodecyltriphenylphosphonium‐mica (C₁₂PPh‐Mica) were used as reinforcing fillers in the fabrication of PET hybrid fibers. The variations of their properties with organoclay content in the polymer matrix and draw ratio (DR) are discussed. Transmission electron microscopy micrographs show that some of the clay layers are dispersed homogeneously within the polymer matrix on the nanoscale, although some clay particles are agglomerated. It was also found that the addition of only a small amount of organoclay is enough to improve the thermal stabilities and mechanical properties of the PET hybrid fibers. Even polymers with low organoclay contents (1–5 wt%) were found to exhibit much higher strength and modulus values than pure PET. In the case of C₁₂PPh‐MMT/PET, the values of the tensile mechanical properties of the hybrid fibers were found to decrease linearly with increases in DR from 1 to 16. However, the tensile mechanical properties of the C₁₂PPh‐Mica hybrid fibers were found to be independent of DR. Copyright © 2006 Society of Chemical Industry     

Colorless polyimide nanocomposite films: Thermomechanical properties,morphology, and optical transparency

Polyimide (PI)/organoclay hybrid films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium‐mica (C₁₂PPh‐Mica) as the organoclay. The variations with organoclay content of the thermomechanical properties, morphology, and optical transparency of the hybrids were examined for concentrations from 0 to 1.0 wt %. For low clay contents (≤ 0.5 wt %), the clay particles are better dispersed in the matrix polymer, without the formation of large agglomerates of particles, than they are for high clay contents. However, agglomerated structures form and become denser in the PI matrix for clay contents ≥ 0.75 wt %. This is in agreement with the observed trends in the thermomechanical properties and the optical transparency, which worsen drastically when the clay content of the C₁₂PPh‐Mica/PI hybrids reaches 0.75 wt %. However, when the amount of organoclay in the hybrid is 0.75 wt %, the initial modulus of the hybrid film is at its maximum value. The PI hybrid films were found to exhibit excellent optical transparencies and to be almost colorless. It was found, however, that the transparency decreases slightly with increases in the organoclay content because of agglomeration of the clay particles. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly(butylene terephthalate) nanocomposite fibers: Thermo‐mechanical properties and morphology

Nanocomposites of poly(butylene terephthalate) (PBT) with the organoclay C₁₂PPh‐MMT were prepared using in situ intercalation polymerization. Hybrids with various organoclay contents were processed for fiber spinning to examine their thermal behavior, tensile mechanical properties, and morphologies for various draw ratios (DRs). The thermal properties (T_g, T_m, and T_Dⁱ) of the hybrid fibers were found to be better than those of pure PBT fibers and were unchanged by variation of the organoclay loading up to 2 wt %. However, these thermal properties remained unchanged for DRs ranging from 1 to 18. Most clay layers were dispersed homogeneously in the matrix polymer, although some clusters were also detected. The tensile properties of the hybrid fibers increased gradually with increasing C₁₂PPh‐MMT content at DR = 1. However, the ultimate strengths and initial moduli of the hybrid fibers decreased markedly with increasing DR. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1247–1254, 2006     

Effect of compatibilizer and organoclay content on structure,thermal, and mechanical properties of poly(butylene succinate)/(Ethylene acrylic acid)/Organoclay nanocomposites

Poly(butylene succinate) (PBS)/(ethylene acrylic acid) (EAA)/organoclay nanocomposites were prepared by using the melt intercalation technique. EAA was used as compatibilizer and organoclay was used as inorganic filler. X‐ray diffraction and transmission electron microscopy results indicated the addition of compatibilizer led to a large increase in basal spacing of nanocomposites and better overall dispersion of organoclay in the PBS matrix. However, the basal spacing was found to be invariant as the organoclay content increased. The differential scanning calorimetry analyses revealed that the incorporation of the organoclay and EAA and the variation of organoclay content altered the melting behavior and crystallization properties of PBS. Storage and loss modulus of virgin matrix increased with the incorporation of organoclay and EAA, and a maximum for the nanocomposite with 9 wt% organoclay. Moreover, the glass transition temperatures also increased for the various organoclay‐containing samples. Mechanical properties showed an increase with the incorporation of organoclay and EAA. The 5 wt% organoclay‐filled PBS gave the highest tensile strength and notched Izod impact strength among all the composites. Further increments in organoclay loading reduced the tensile strength and notched impact strength of nanocomposites, which was thought to be the result of agglomeration. However, increments in clay loading enhanced the flexural strength and flexural modulus of nanocomposites, with a maximum at 9 wt% organoclay. J. VINYL ADDIT. TECHNOL., 23:219–227, 2017. © 2015 Society of Plastics Engineers     

New aramid‐based nanocomposites: Synthesis and characterization

New type of nanocomposites containing various proportions of montmorillonite in aromatic polyamide was prepared via solution intercalation method. Aramid chains were synthesized by reacting 4,4′‐oxydianiline with isophthaloyl chloride in N,N′‐dimethyl acetamide. Dodecylamine was used as swelling agent to change the hydrophilic nature of montmorillonite into organophilic. Appropriate amounts of organoclay were mixed in the polymer solution using high‐speed mixer for complete dispersion of the clay. Thin films cast from these materials after evaporating the solvent were characterized by XRD, TEM, mechanical, thermal, and water absorption measurements. The structure and morphology of the nanocomposites determined by XRD and TEM revealed the formation of exfoliated and intercalated clay platelets in the aramid matrix. Mechanical data indicated improvement in the tensile strength and modulus of the nanocomposites with clay loading up to 6 wt%. The glass transition temperature increased up to 12 wt% clay content and thermal stability amplified with increasing clay loading. The water absorption reduced gradually as a function of organoclay and approached to zero with 20 wt% organoclay in the aramid. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Poly(ethylene terephthalate) nanocomposite fibers by in situ polymerization: The thermomechanical properties and morphology

A series of nanocomposites of poly(ethylene terephthalate) (PET) with the organoclay dodecyltriphenylphosphonium‐mica (C₁₂PPh‐mica) were synthesized with the in situ polymerization method. PET hybrid fibers with various organoclay concentrations were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PET hybrid fibers were characterized with differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and universal tensile analysis. The organoclay was intercalated in the polymer matrix at all magnification levels, and some of the agglomerated organoclay layers were greater than 50 nm thick. The thermal stabilities and initial tensile moduli of the hybrid fibers increased with an increasing clay content for DR = 1. For DR = 1, the ultimate tensile strengths of the PET hybrid fibers increased with the addition of clay up to a critical clay loading and then decreased above that critical concentration. However, the tensile mechanical properties of the hybrid fibers did not improve with increasing DR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2009–2016, 2005     

Poly(ethylene terephthalate) nanocomposites by in situ interlayer polymerization: the thermo-mechanical properties and morphology of the hybrid fibers

Nanocomposites of poly(ethylene terephthalate) (PET) with C₁₂PPh-MMT as an organoclay were synthesized by using the in situ interlayer polymerization approach. The PET nanocomposites were melt-spun at different organoclay contents and different draw ratios to produce monofilaments. The thermo-mechanical properties and the morphologies of the PET nanocomposites were examined by using a differential scanning calorimeter, a thermogravimetric analyzer, a wide angle X-ray diffactometer, scanning and transmission electron microscopes, and a universal tensile machine. Some of the clay particles were well dispersed in the PET matrix, and some of them were agglomerated at a size level of greater than approximately 10 nm. The thermal stability and the tensile mechanical properties of the PET hybrid fibers increased with increasing clay content at a DR=1. However, the values of the ultimate tensile strength and the initial modulus of the hybrid fibers decreased markedly with increasing DR from 1 to 16.     

Preparation and characterization of polyurethane–organoclay nanocomposites

Nanocomposite polyurethane (PU)–organoclay materials have been synthesized via in‐situ polymerization. The organoclay is first prepared by intercalation of tyramine into montmorillonite (MMT)‐clay through ion exchange process. The syntheses of polyurethane–organoclay hybrid films containing different ratios of clay were carried out by swelling the organoclay into diol and diamine followed by addition of diisocyanate and then cured. The nanocomposites with dispersed and exfoliated structure of MMT were obtained as evidenced by X‐ray diffraction and scanning electron microscope. X‐ray diffraction showed that there is no peak corresponding to d₀₀₁ spacing in organoclay with the ratios up to 20 wt%. SEM images confirmed the dispersion of nanometer silicate layers in the polyurethane matrix. Also, it was found that the presence of organoclay leads to improvement in the mechanical properties. The tensile strength was increased with increasing the organoclay contents to 20 wt% by 221% in comparision to the PU with 0% organoclay. POLYM. COMPOS. 28:108–115, 2007. © 2007 Society of Plastics Engineers     

CO2 sorption and diffusion in polymethyl methacrylate–clay nanocomposites

This study reports the glass transition temperature (T_g), and sorption and diffusion of subcritical CO₂ gas in polymethyl methacrylate (PMMA) nanocomposites containing organically modified smectite clay, Cloisite 20A (C20A). A range of methods for preparing the PMMA‐clay nanocomposites was investigated and a solution coprecipitation method was selected as the most appropriate. Using this method, PMMA nanocomposite containing 2, 4, 6, and 10 wt% nanoclay loadings were prepared. Wide‐angle X‐ray diffraction (XRD) analysis and scanning electron microscopy (SEM) indicated that the 2 wt% nanocomposite materials had a well‐dispersed intercalated clay structure. The T_g for PMMA‐C20A nanocomposites, as measured by differential scanning calorimetry (DSC), was found to be independent of the clay loading. CO₂ solubility studies from 0 to 65°C and pressures up to 5.5 MPa using an in situ gravimetric technique were performed on compression‐molded films. The organoclay was found to have no effect on the solubility of CO₂ in PMMA, and therefore the solubility of CO₂ in the nanocomposite can be determined from the solubility of CO₂ in the matrix polymer alone. Diffusion coefficients were determined using the appropriate transport models for these test conditions and the diffusion coefficients for CO₂ in PMMA‐C20A composites were found to increase with organoclay loading. It is believed that the processing path taken to prepare the nanocomposites may have resulted in the agglomeration of the C20A organoclay, thereby preventing the polymer chains from fully wetting and intercalating a large number of clay particles. These agglomerations are responsible for the formation of large‐scale holes within the glassy nanocomposite, which behave as low resistance pathways for gas transport within the PMMA matrix. POLYM. ENG. SCI., 45:904–914, 2005. © 2005 Society of Plastics Engineers     

Preparation,microstructure, mechanical,and thermal properties of in situ polymerized polyimide/organically modified sericite mica composites

In this work, sericite mica was initially modified with a multi‐step procedure and the novel composites of polyimide (PI) with the organophilic sericite mica were subsequently synthesized via in situ polymerization technique. XRD patterns revealed d₀₀₂‐spacing of clay was expanded from 0.99 to 2.77 nm. TEM photographs indicated majority of the organoclay exhibited an exfoliated morphology structure in composites with 5 wt% filler loading. Several critical properties of composites such as thermal stability, mechanical property, and storage modulus were tremendously enhanced with the increasing organoclay loading. Especially, the glass transition temperature of composites with 7 wt% organoclay addition revealed a 72°C increment compared with pristine PI, indicating greater improvement than the reported literature values. POLYM. COMPOS., 37:2243–2251, 2016. © 2015 Society of Plastics Engineers     

Poly(butylene terephthalate)/organoclay nanocomposites prepared by in situ interlayer polymerization and its fiber (II)

Intercalated nanocomposites with poly(butylene terephthalate) (PBT) incorporated between the montmorillonite layers were synthesized from dimethyl terephthalate and 1,4-butane diol by using an in situ interlayer polymerization. The PBT nanocomposites were melt-spun at different organoclay contents to produce monofilaments. The samples were characterized by using wide angle X-ray diffraction, electron microscopy, thermal analysis, and tensile testing. The extent of the clay layer in the PBT was confirmed by using X-ray diffraction and electron microscopy, and the clay layer was found to be highly dispersed on a nanometer scale. The addition of only a small amount of organoclay was enough to improve the thermo-mechanical properties of the PBT hybrid fibers. The hybrids were extruded with various draw ratios (DRs) to examine the tensile mechanical property of the fibers. At DR=1, the ultimate tensile strength of the hybrid fibers increased with the addition of clay up to a critical content and then decreased. However, the initial modulus monotonically increased with increasing amount of organoclay in the PBT matrix. When the DR was increased from 1 to 6, for example, the strength and the initial modulus values of the hybrids containing 3 wt% organoclay decreased linearly.     

Effect of blend composition and organoclay loading on the nanocomposite structure and properties of miscible poly(methyl methacrylate)/poly(styrene‐co‐acrylonitrile) blends

Organically‐modified montmorillonite clay nanocomposites of poly(styrene‐co‐acrylonitrile) (SAN), poly(methyl methacrylate) (PMMA) and SAN/PMMA miscible blend are investigated. Structure characteristics at the nanoscale and microscale and thermal and tensile properties are studied as a function of polymer blend composition and filler loading fraction. Blend miscibility and T_g are unaffected by up to 10% by wt. organoclay. Thermal degradation stability increases with SAN content and exhibits an optimum value of clay loading. Stiffness shows significant improvement. Tensile strength and elongation‐at‐break suffer as a result of nanocomposite formation. Modulus shows a maximum enhancement of 57% (5 ± 0.06 GPa at 10 wt% filler, 20/80 SAN/PMMA) and varies linearly with clay fraction for all compositions of matrix phase. Predictions of Halpin–Tsai composite model are in excellent agreement with the experimental behavior over full range of polymer blend composition. Fundamental aspects of a polymer blend–clay nanocomposite are clarified, such as lack of additional synergy between clay platelets and matrix, and tensile ductility reduction, compared with polymer–clay system. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

The effects of hybrid fillers on thermal,mechanical, physical,and antimicrobial properties of ultrahigh‐molecular‐weight polyethylene‐reinforced composites

The effects of hybrid filler of zinc oxide and chitosan (chitosan–ZnO) on thermal, flexural, antimicrobial, chemical resistance, and hardness properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE) composites with varying concentration of zinc oxide (ZnO) and further hybridized by chitosan (CS) were successfully studied. The composites were prepared using mechanical ball milling and followed by hot compression molding. The addition of ZnO to the UHMWPE matrix had lowered the melting temperature (T _m) of the composite but delayed its degradation temperature. Further investigation of dual filler incorporation was done by the addition of chitosan to the UHMWPE/ZnO composite and resulted in the reduction of UHMWPE crystallization. The flexural strength and modulus had a notably high improvement through ZnO addition up to 25 wt% as compared to neat UHMWPE. However, the addition of chitosan had resulted in lower flexural strength than that of 12 wt% ZnO UHMWPE composite but still higher than that of neat UHMWPE. It was experimentally proven that the incorporation of ZnO and chitosan particles within UHMWPE matrix had further enhanced the antimicrobial properties of neat UHMWPE. Chemical resistance was improved with higher ZnO content with a slight reduction of mass change after the incorporation of chitosan. The hardness value increased with ZnO addition but higher incorporation of chitosan had lowered the hardness value. These findings have significant implications for the commercial application of UHMWPE based products. It appears that these hybrid fillers (chitosan–ZnO)‐reinforced UHMWPE composites exhibit superior overall properties than that of conventional neat UHMWPE. POLYM. COMPOS., 38:1689–1697, 2017. © 2015 Society of Plastics Engineers     

The Nucleating Effect of Montmorillonite on Crystallization of PET/Montmorillonite Nanocomposite

Poly(ethylene terephthalate) (PET)/montmorillonite (MMT) nanocomposites were prepared by solution intercalation method. The clay was organo-modified with intercalation agent of cetyltrimetylammonium chloride (CMC). XRD showed that the layers of MMT were intercalated by CMC. Four nanocomposites with organoclay contents of 1, 5, 10, and 15 wt% were prepared by solution blending. XRD showed that the interlayer spacing of organoclay in the nanocomposites depends on the amount of organoclay. The nucleating effect of organoclay is investigated using differential scanning calorimetry (DSC) analysis. Clay behaves as a nucleating agent and enhances the crystallization rate of PET. Maximum enhancement in crystallization rate for the nanocomposites was observed in blends containing ca. 10 wt% of clay in the range of 1–15 wt%. According to transmission electron microscopy (TEM), the organoclay particle was highly dispersed in the PET matrix without a large agglomeration of particles for low organoclay content (5 wt%). Agglomerated structure did form in the PET matrix at 15 wt% organoclay content.     

Characteristics of impact modified polystyrene/organoclay nanocomposites

The poor impact resistance of Polystyrene (PS) was enhanced by the addition of elastomeric material, SEBS‐g‐MA. To prevent the reduction in strength and stiffness, organoclay Cloisite® 25A was used as filler and introduced into the matrix by a corotating twin screw extruder. Throughout the study, the clay content was kept at 2 wt%, whereas the content of SEBS‐g‐MA was varied between 5 and 40 wt%. It was found that Cloisite® 25A displays well dispersion in the ternary nanocomposites and the degree of dispersion increases with the elastomer content. The elastomeric phase has a greater viscosity than pure PS. Thus, as expected, at low elastomer contents, it forms the dispersed phase in the matrix as droplets. Transmission electron microscopy results show that the clay layers reside at the interphase between PS and elastomer and also inside the elastomeric phase. Owing to the location of the clay particles, the average elastomer domain size in ternary nanocomposites are found to be greater than that in the relative binary blends of PS‐(SEBS‐g‐MA). Moreover, with the organoclay addition, phase inversion point shifts to lower elastomer contents. The mechanical test results showed that the nanocomposites containing 15 and 20 wt% SEBS‐g‐MA have the optimum average domain size that results in high‐impact strength values without deteriorating the tensile properties. POLYM. COMPOS., 31:1853–1861, 2010. © 2010 Society of Plastics Engineers.     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Polyimide nanocomposite with a hexadecylamine clay: Synthesis and characterization

A poly(amic acid) was prepared by the reaction of 3,3′‐dihydroxybenzidine and pyromellitic dianhydride in N,N‐dimethylacetamide. Hexadecylamine was used as an organophilic alkylamine in organoclay. Cast films were obtained from blend solutions of the precursor polymer and the organoclay. The cast film was heat treated at different temperatures to create polyimide (PI) hybrid films. We set out to clarify the intercalation of PI chains to hexadecylamine–montmorillonite (C₁₆–MMT) and to improve thermal and tensile properties and the gas barrier. It was found that the addition of only a small amount of organoclay was enough to improve both the thermal and the mechanical properties of PIs. Maximum enhancement in the ultimate tensile strength for PI hybrids was observed for the blends containing 4% C₁₆–MMT. The initial modulus monotonically increased with further increases in C₁₆–MMT content. Water vapor permeability was decreased with increasing clay loading from 1 to 8 wt %. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2294–2301, 2002     

Poly(trimethylene terephthalate) nanocomposite fibers comprising different organoclays: Thermomechanical properties and morphology

Poly(trimethylene terephthalate) (PTT) nano composites were synthesized by in situ polymerization at high temperature with two thermally stable organoclays: 1,2‐dimethylhexadecylimidazolium‐montmorillonite (IMD‐MMT) and dodecyltriphenyl phosphonium‐MMT (C₁₂PPh‐MMT). PTT hybrid fibers with various organoclay contents were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PTT hybrid fibers were characterized using differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and mechanical tensile properties analysis. The nanostructure of the hybrid fibers was observed by both scanning and transmission electron microscopy, which showed that the clay layers were well dispersed into the matrix polymer, although some clusters or agglomerated particles were also detected. Unlike the hybrids containing IMD‐MMT, the clay layers of the C₁₂PPh‐MMT hybrid fiber were more dispersed into the matrix polymer. The thermal stability and tensile properties of the hybrid fibers increased with increasing clay content for DR = 1. However, as DR increased from 1 to 9 the ultimate strength and initial modulus of the hybrid fibers with IMD‐MMT increased slightly whereas those of C₁₂PPh‐MMT hybrid fibers decreased slightly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4535–4545, 2006     

Poly(vinyl alcohol) nanocomposites with different clays: Pristine clays and organoclays

Poly(vinyl alcohol) (PVA)/clay nanocomposites were synthesized using the solution intercalation method. Na ion‐exchanged clays [Na⁺–saponite (SPT) and Na⁺–montmorillonite (MMT)] and alkyl ammonium ion‐exchanged clays (C₁₂–MMT and C₁₂OOH–MMT) were used for the PVA nanocomposites. From the morphological studies, the Na ion‐exchanged clay is more easily dispersed in a PVA matrix than is the alkyl ammonium ion‐exchanged clay. Attempts were also made to improve both the thermal stabilities and the tensile properties of PVA/clay nanocomposite films, and it was found that the addition of only a small amount of clay was sufficient for that purpose. Both the ultimate tensile strength and the initial modulus for the nanocomposites increased gradually with clay loading up to 8 wt %. In C₁₂OOH–MMT, the maximum enhancement of the ultimate tensile strength and the initial modulus for the nanocomposites was observed for blends containing 6 wt % organoclay. Na ion‐exchanged clays have higher tensile strengths than those of organic alkyl‐exchanged clays in PVA nanocomposites films. On the other hand, organic alkyl‐exchanged clays have initial moduli that are better than those of Na ion‐exchanged clays. Overall, the content of clay particles in the polymer matrix affect both the thermal stability and the tensile properties of the polymer/clay nanocomposites. However, a change in thermal stability with clay was not significant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3208–3214, 2003     

Synthesis and properties of polybenzoxazole-clay nanocomposites

A novel polybenzoxazole (PBO)/clay nanocomposite has been prepared from a PBO precursor, polyhydroxyamide (PHA) and an organoclay. The PBO precursor was made by the low temperature polycondensation reaction between isophthaloyl chloride (IC) and 2,2-bis(3-amino-4-hydroxyphenyl)hexafluoropropane with an inherent viscosity of 0.5 dl/g. The organoclay was formed by a cation exchange reaction between a Na⁺-montorillonite (Na⁺-Mont) clay and an ammonium salt of dodecylamine. The PHA/clay was subsequently thermal cured to PBO/clay. Both X-ray diffraction and transmission electron microscope analyzes showed that the organoclay was dispersed in the PBO matrix in a nanometer scale. The in-plane coefficient of thermal expansion (CTE) of PBO/clay film decreased with increasing amounts of organoclay. The CTE of PBO/clay film containing 7 wt% clay was decreased by 21% compared to the pure PBO film. Both of the glass transition temperature (T_g) and the thermal decomposition temperature of PBO/clay increased with increasing amounts of organoclay. The thermal decomposition temperature and the T_g of PBO/clay containing 7 wt% clay increased to 12 and 16 °C, respectively.