Morphology and electrical properties of polymethylmethacrylate/poly(styrene‐co‐acrylonitrile)/multi‐walled carbon nanotube nanocomposites

Nanocomposites of blends of polymethylmethacrylate (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with multi‐walled carbon nanotubes (MWCNTs) were prepared by melt mixing in a twin‐screw extruder. The dispersion state of MWCNTs in the matrix polymers was investigated using transmission electron microscopy. Interestingly enough, in most of the nanocomposites, the MWCNTs were observed to be mainly located at SAN domains, regardless of the SAN compositions in the PMMA/SAN blend and of the processing method. One possible reason for this morphology may be the π–π interactions between MWCNTs and the phenyl ring of SAN. The shift in G‐band peak observed in the Raman spectroscopy may be the indirect evidence proving these interactions. The percolation threshold for electrical conductivity of PMMA/SAN/MWCNT nanocomposites was observed to be around 1.5 wt %. Nanocomposites with PMMA‐rich composition showed higher electrical conductivity than SAN‐rich nanocomposites at a fixed MWCNT loading. The dielectric constant measurement also showed composition‐dependent behavior. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of compatibilizer on the morphological,mechanical, and rheological properties of poly(methyl methacrylate)/poly(N‐methyl methacrylimide) blends

The effects of compatibilizer on the morphological, thermal, mechanical, and rheological properties of poly(methyl methacrylate) (PMMA)/poly(N‐methyl methacrylimide) (PMMI) (70/30) blends were investigated. The compatibilizer used in this study was styrene–acrylonitrile–glycidyl methacrylate (SAN‐GMA) copolymer. Morphological characterization of the PMMA/PMMI (70/30) blend with SAN‐GMA showed a decrease in PMMI droplet size with an increase in SAN‐GMA. The glass‐transition temperature of the PMMA‐rich phase became higher when SAN‐GMA was added up to 5 parts per hundred resin by weight (phr). The flexural and tensile strengths of the PMMA/PMMI (70/30) blend increased with the addition of SAN‐GMA up to 5 phr. The complex viscosity of the PMMA/PMMI (70/30) blends increased when SAN‐GMA was added up to 5 phr, which implies an increase in compatibility between the PMMA and PMMI components. From the weighted relaxation spectrum, which was obtained from the storage modulus and loss modulus, the interfacial tension of the PMMA/PMMI (70/30) blend was calculated using the Palierne emulsion model and the Choi‐Schowalter model. The results of the morphological, thermal, mechanical, and rheological studies and the values of the interfacial tension of the PMMA/PMMI (70/30) blends suggest that the optimum compatibilizer concentration of SAN‐GMA is 5 phr. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43856.     

Molecular simulation of miscibility of poly(2,6‐dimethyl‐1,4‐phenylene ether)/poly(styrene‐co‐acrylonitrile) blend with the compatibilizer triblock terpolymer SBM

Polymer blend of poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE) and poly(styrene‐co‐acrylonitrile) (SAN), which has broad commercial interest, has limited miscibility. A triblock terpolymer, polystyrene‐block‐polybutadiene‐block‐poly(methyl methacrylate) (SBM), is often used as compatibilizer to improve the miscibility of PPE/SAN. In this work, dissipative particle dynamics and molecular dynamics of Material Studio were used to study the essentials that influence miscibility of the blend systems, and then Flory–Huggins parameter χ, radial distribution function (RDF) and morphologies are analyzed. It shows that the blends with more content of styrene in SAN (above 90 wt%), whose mass percentage is 60%, are best miscible. For the systems of PPE/SAN added with SBM, the miscibility increases and then decreases with the increase of SBM content. A longer chain of styrene (S) in SBM leads to wrapped structure of PMMA by PB, wrapped by PS, resulting in decrease of the miscibility. From studies and simulation of χ and RDF, the best blend system for commercial and industrial use is the one with mass ratio of PPE/SAN/SBM 36/54/10, in which S content in SAN is above 90 wt%. For SBM, the ratio of chain length styrene (S)/butadiene (B) is lessthan 1, while B and M are the same in chain length. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

New poly(phenylene oxide)/polystyrene blend nanocomposites with clay: Intercalation,thermal and mechanical properties

We present the first study and results on the preparation and characterization of montmorillonite clay filler based polymer blend nanocomposites of the miscible poly(phenylene oxide)/polystyrene blend. Intercalated nanocomposites, prepared by a melt‐processing method with 2–6 wt % commercially available organically modified sodium montmorillonite, have been characterized with wide‐angle X‐ray diffraction, transmission electron microscopy analysis, thermal analysis (thermogravimetric analysis and differential scanning calorimetry), and mechanical tensile tests. We show that nanocomposites can be successfully prepared in a batch mixer at temperatures much below the conditions conventionally used for this blend without organic degradation. Thermal stability is enhanced by nanoscale hybrid formation. The level of intercalation (change in the d‐spacing) does not change with the clay loading. Better dispersion of clay in the blend matrix has been observed at a low level of clay content. The nanocomposites show improved tensile modulus (by 31%) in comparison to the blend, whereas the tensile strength (stress at break) and elongation decrease in the presence of the filler with an increase in the clay loading. The Halpin–Tsai model is able to predict the modulus of the nanocomposites in very good agreement with the experimental data. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Nanocomposites based on vermiculite clay and ternary blend of poly(L‐lactic acid), poly(methyl methacrylate), and poly(ethylene oxide)

Vermiculite (VMT) as clay was introduced into a ternary polymer blend composed of poly(L ‐lactic acid) (PLLA), poly(methyl methacrylate) (PMMA), and poly(ethylene oxide) (PEO), whose ternary miscibility was proven within low certain contents of PMMA and PEO in PLLA. VMT was incorporated to the ternary polymer blend as matrix after proper organic modification on the clay. The organically modified vermiculite (OVMT) shows good interaction and acceptable dispersion in the ternary polymer matrix without altering the crystal structures of PLLA/PEO constituents. The effect of OVMT addition was then analyzed in isothermal crystallization by using the Avrami kinetic analysis, and the addition of OVMT is evident in altering nucleation process of the polymer blend as well as the crystal perfection. The activation energy is much lowered by the addition of OVMT, as evident from the analysis; the overall crystallization kinetic rates are increased with the incorporation of OVMT. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Investigation on the miscibility of the blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The miscibility was investigated in blends of poly(methyl methacrylate) (PMMA) and styrene‐acrylonitrile (SAN) copolymers with different acrylonitrile (AN) contents. The 50/50 wt % blends of PMMA with the SAN copolymers containing 5, 35, and 50 wt % of AN were immiscible, while the blend with copolymer containing 25 wt % of AN was miscible. The morphologies of PMMA/SAN blends were characterized by virtue of scanning electron microscopy and transmission electron microscopy. It was found that the miscibility of PMMA/SAN blends were in consistence with the morphologies observed. Moreover, the different morphologies in blends of PMMA and SAN were also observed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Designing of fullers‐earth‐containing poly(vinyl alcohol)‐g‐poly(2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid) nanocomposites: Swelling and deswelling behaviors

In this study, polymer–clay nanocomposites (PCNs) composed of poly(vinyl alcohol)s (PVAs), poly(2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid), and fullers earth were prepared by the effective dispersal of inorganic nanoclays in the organic PVA matrix via in situ free‐radical polymerization with potassium persulfate as an initiator and N,N‐methylene bisacrylamide as a crosslinker. The monomer, 2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid, was grafted onto the PVA backbone, and at the same time, fullers earth layers were intercalated and exfoliated into the grafted copolymer, especially at a low or moderate loading of the fullers earth. The synthesized PCN materials were characterized by Fourier transform infrared spectroscopy and wide‐angle X‐ray diffraction techniques. The morphological features of the synthesized materials were studied by scanning electron microscopy; this revealed that the swelling ratio of this nanocomposite increased with increasing fullers earth content. The X‐ray diffraction results indicated that the fullers earth was exfoliated in the nanocomposite matrix, and its introduction into the polymer matrix enhanced the percentage crystallinity of the polymer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology and tensile properties of crosslinked nanocomposite foams of low‐density polyethylene and poly(ethylene‐co‐vinyl acetate) blends

This paper studies the morphology and tensile properties of nanocomposite foams of blends of low‐density polyethylene (LDPE) and poly(ethylene‐co‐vinyl acetate) (EVA). Preparations of LDPE/EVA nanocomposites were conducted in an internal mixer, and then samples were foamed via a batch foaming method. Morphology of the nanocomposite blends and nanocomposite foams was studied by X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy. Morphological observations showed that nanoparticle dispersion in the polymeric matrix was affected by the blend ratio in a way such that EVA‐rich samples had a better dispersion of nanoclay than LDPE‐rich ones. In addition, the tensile properties of the nanocomposite foams were related to different variables such as blend ratio, clay content, and foam density. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Phase morphology and thermomechanical analysis of poly(styrene‐co‐acrylonitrile)/ethylene–propylene–diene monomer blends: Uncompatibilized and reactively compatibilized blends with two mixing sequences

The phase morphology developing in immiscible poly(styrene‐co‐acrylonitrile) (SAN)/ethylene–propylene–diene monomer (EPDM) blends was studied with an in situ reactively generated SAN‐g‐EPDM compatibilizer through the introduction of a suitably chosen polymer additive (maleic anhydride) and 2,5‐dimethyl‐2,5‐di‐(t‐butyl peroxy) hexane (Luperox) and dicumyl peroxide as initiators during melt blending. Special attention was paid to the experimental conditions required for changing the droplet morphology for the dispersed phase. Two different mixing sequences (simple and two‐step) were used. The product of two‐step blending was a major phase surrounded by rubber particles; these rubber particles contained the occluded matrix phase. Depending on the mixing sequence, this particular phase morphology could be forced or could occur spontaneously. The composition was stabilized by the formation of the SAN‐g‐EPDM copolymer between the elastomer and addition polymer, which was characterized with Fourier transform infrared. As for the two initiators, the blends with Luperox showed better mechanical properties. Scanning electron microscopy studies revealed good compatibility for the SAN/EPDM blends produced by two‐step blending with this initiator. Dynamic mechanical thermal analysis studies showed that the two‐step‐prepared blend with Luperox had the best compatibility. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of organic modification on mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites

The influence of organic modifiers on intercalation extent, structure, thermal and mechanical properties of poly(methyl methacrylate) (PMMA)–clay nanocomposites were studied. Two different organic modifiers with varying hydrophobicity (single tallow versus ditallow) were investigated. The nanocomposites were prepared from melt processing method and characterized using wide angle X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, differential scanning calorimetry (DSC), and tensile tests. Mechanical properties such as tensile modulus (E), break stress (σ_brk), and % break strain (ε_brk) were determined for nanocomposites at various clay loadings. Extent of PMMA intercalation is sufficient and in the range 9–15 Å depending on organoclay and filler loading. Overall thermal stability of nanocomposites increases by 16–30°C. The enhancement in T_g of nanocomposite is merely by 2–4°C. With increase in clay loading, tensile modulus increases linearly while % break strain decreases. Break stress is found to increase till 4 wt % and further decreases at higher clay loadings. The overall improvement in thermal and mechanical properties was higher for the organoclay containing organic modifier with lower hydrophobicity and single tallow amine chemical structure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blending poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) as composite polymer electrolyte

A blend of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (PSAN) has been evaluated as a composite polymer electrolyte by means of differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, ac impedance measurements, and linear sweep voltammetry (LSV). The blends show an interaction with the Li⁺ ions when complexed with lithium perchlorate (LiClO₄), which results in an increase in the glass‐transition temperature (T_g) of the blends. The purpose of using PSAN as another component of the blend is to improve the poor mechanical properties of PMMA‐based plasticized electrolytes. The mechanical property is further improved by introducing fumed silica as inert filler, and hence the liquid electrolyte uptake and ionic conductivity of the composite systems are increased. Room‐temperature conductivity of the order of 10^?4 S/cm has been achieved for one of the composite electrolytes made from a 1/1 blend of PSAN and PMMA containing 120% liquid electrolyte [1M LiClO₄/propylene carbonate (PC)] and 10% fumed silica. These systems also showed good compatibility with Li electrodes and sufficient electrochemical stability for safe operation in Li batteries. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1319–1328, 2001     

Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

Poly(para‐dioxanone)/poly(D,L‐lactide) blends compatibilized with poly(D,L‐lactide‐co‐para‐dioxanone)

The effect of poly(D ,L ‐lactide‐co‐para‐dioxanone) (PLADO) as the compatibilizer on the properties of the blend of poly(para‐dioxanone) (PPDO) and poly(D ,L ‐lactide) (PDLLA) has been investigated. The 80/20 PPDO/PDLLA blends containing from 1% to 10% of random copolymer PLADO were prepared by solution coprecipitation. The PLADO component played a very important role in determining morphology, thermal, mechanical, and hydrophilic properties of the blends. Addition of PLADO into the blends could enhance the compatibility between dispersed PDLLA phase and PPDO matrix; the boundary between the two phases became unclear and even the smallest holes were not detected. On the other hand, the position of the T_g was composition dependent; when 5% PLADO was added into blend, the T_g distance between PPDO and PDLLA was shortened. The blends with various contents of compatibilizer had better mechanical properties compared with simple PPDO/PDLLA binary polymer blend, and such characteristics further improved as adding 5% random copolymers. The maximum observed tensile strength was 29.05 MPa for the compatibilized PPDO/PDLLA blend with 5% PLADO, whereas tensile strength of the uncompatibilized PPDO/PDLLA blend was 14.03 MPa, which was the lowest tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Comparative studies of the properties of poly(methyl methacrylate)–clay nanocomposite materials prepared by in situ emulsion polymerization and solution dispersion

A series of polymer–clay nanocomposite (PCN) materials consisting of organic poly(methyl methacrylate) (PMMA) and inorganic montmorillonite (MMT) clay platelets were prepared successfully by the effective dispersion of nanolayers of the MMT clay in the PMMA framework through both in situ emulsion polymerization and solution dispersion. The as‐prepared PCN materials obtained with both approaches were subsequently characterized with wide‐angle powder X‐ray diffraction and transmission electron microscopy. For a comparison of the anticorrosion performance, a PCN material (e.g., 3 wt % clay loading) prepared by in situ emulsion polymerization, showing better dispersion of the clay platelets in the polymer matrix, exhibited better corrosion protection in the form of a coating on a cold‐rolled steel coupon than that prepared by solution dispersion, which showed a poor dispersion of the clay nanolayers according to a series of electrochemical corrosion measurements. Comparative studies of the optical clarity, molecular barrier properties, and thermal stability of samples prepared in both ways, as membranes and fine powders, were also performed with ultraviolet–visible transmission spectroscopy, molecular permeability analysis, thermogravimetric analysis, and differential scanning calorimetry. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1936–1946, 2004     

Mechanical and morphological properties of lyocell blends: Comparison with lyocell nanocomposites (I)

The mechanical properties and morphologies of polyblends of lyocell with three different fillers are compared. Poly(vinyl alcohol) (PVA), poly(vinyl alcohol‐co‐ethylene) (EVOH), and poly(acrylic acid‐co‐maleic acid) (PAM) were used as fillers in blends with lyocell produced through solution blending. The variations of their properties with polymer matrix filler content are discussed. The ultimate tensile strength of the PVA/lyocell blend is highest for a blend lyocell content of 30 wt %, and decreases as the lyocell content is increased up to 40 wt %. The ultimate tensile strengths of the EVOH/lyocell and PAM/lyocell blends are highest for a lyocell loading of 20 wt %, and decrease with the increasing filler content. The variations in the initial moduli of the blends with filler content are similar. Of the three blend systems, the blends with PVA exhibit the best tensile properties. Lyocell/organoclay hybrid films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium–Mica (C₁₂PPh‐ Mica) as the organoclay. The variation of the mechanical tensile properties of the hybrids with the matrix polymer organoclay content was examined. These properties were found to be optimal for an organoclay content of up to 5 wt %. Even polymers with low organoclay contents exhibited better mechanical properties than pure lyocell. The addition of organoclay to lyocell to produce nanocomposite films was found to be less effective in improving its ultimate tensile strength than blending lyocell with the polymers. However, the initial moduli of the nanocomposites were found to be higher than those of the polyblend films. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis,characterization, and mechanical property of poly(urethane‐glycidyl methacrylate‐methyl methacrylate) hybrid polymers

Hybrid particles of polyurethane (PU) containing a number of small poly(methyl methacrylate) (PMMA) nanoparticles inside were prepared using glycidyl methacrylate (GMA) monomer as a linker between PU and PMMA; the resulting polymers were poly (urethane‐glycidyl methacrylate‐methyl methacrylate) (PUGM). It was found that the average particle size (D_p) of the PU particles decreased by the inclusion of PMMA particles possibly owing to the low‐solution viscosity of PU. However, D_p of the PUGM hybrid particles increased with increasing the number of covalent bonds between PMMA and PU, which might be due to decreasing the amount of ionic groups per PU chain. Subsequently, the tensile properties of the films made of the PUGM hybrid particles were investigated. It was observed that the modulus of the PU films increased upon the addition of PMMA particle because of a filler effect. In addition, it was seen that the modulus of PUGM hybrid films increased further with increasing the number of covalent bonds. This was attributed to “restricted mobility” of PU chains anchored to the PMMA particles. It was also observed that the tensile strength changed only slightly for PUGM particles, suggesting that the PU matrix was probably responsible for the necking behavior of the films. The elongation of the samples was found to depend on both the presence of covalent bonds between the PMMA particles and PU matrix and the reduced mobility of the PU chains anchored to PMMA particles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(ethylene terephthalate)/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate)/clay nanocomposites: Effects of biaxial stretching

In this study, we fabricated poly(ethylene terephthalate) (PET)/clay, PET/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate) (PETG), and PET/PETG/clay nanocomposite plates and biaxially stretched them into films by using a biaxial film stretching machine. The tensile properties, cold crystallization behavior, optical properties, and gas and water vapor barrier properties of the resulting films were estimated. The biaxial stretching process improved the dispersion of clay platelets in both the PETG and PET/PETG matrices, increased the aspect ratio of the platelets, and made the platelets more oriented. Thus, the tensile, optical, and gas‐barrier properties of the composite films were greatly enhanced. Moreover, strain‐induced crystallization occurred in the PET/PETG blend and in the amorphous PETG matrix. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42207.