Improvement in toughness and crystallization of poly(L‐lactic acid) by melt blending with ethylene/methyl acrylate/glycidyl methacrylate terpolymer

Melt blending of poly(lactic acid) (PLA) and ethylene/methyl acrylate/glycidyl methacrylate terpolymer (EGA) containing relatively high‐concentration epoxide groups (8 wt%) was performed to improve the toughness and crystallization of PLA. The results of nonisothermal and isothermal crystallization investigation showed that the addition of EGA accelerated the crystallization rate and increased the final crystallinity of PLA in the blends. Significant enhancement in toughness and flexibility of PLA were achieved by the incorporation of the EGA elastomer. When 20 wt% EGA added, the impact strength increased from 3.0 kJ m^?2 of neat PLA to 59.8 kJ m^?2 and the elongation at break increased from 4.9 to 232.0%. The failure mode changed from brittle fracture of neat PLA to ductile fracture of the blend. POLYM. ENG. SCI., 53:2498–2508, 2013. © 2013 Society of Plastics Engineers     

Morphology and properties of the biosourced poly(lactic acid)/poly(ethylene oxide‐b‐amide‐12) blends

Biosourced poly(lactic acid) (PLA) blends with different content of poly(ethylene oxide‐b‐amide‐12) (PEBA) were prepared by melt compounding. The miscibility, phase structure, crystallization behavior, mechanical properties, and toughening mechanism were investigated. The blend was an immiscible system with the PEBA domains evenly dispersed in the PLA matrix. The PEBA component suppressed the nonisothermal melt crystallization of PLA. With the addition of PEBA, marked improvement in toughness of PLA was achieved. The maximum for elongation at break and impact strength of the blend reached the level of 346% and 60.5 kJ/m², respectively. The phase morphology evolution in the PLA/PEBA blends after tensile and impact tests was investigated, and the corresponding toughening mechanism was discussed. It was found that the PLA matrix demonstrates obvious shear yielding in the blend during the tensile and impact tests, which induced energy dissipation and therefore lead to improvement in toughness of the PLA/PEBA blends. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Effect of crystallization on microstructure and mechanical properties of poly[(ethylene oxide)‐block‐(amide‐12)]‐toughened poly(lactic acid) blend

The effect of crystallization on the microstructure and mechanical properties of a poly[(ethylene oxide)‐block‐(amide‐12)] (PEBA)‐toughened poly(lactic acid) (PLA) blend was investigated. Annealing was used to govern the crystallization microstructure and hence the mechanical properties of the blend. Crystallization resulted in the morphology of the PLA component altering from a continuous amorphous phase to continuous crystalline phase. Moreover, as the crystallization of PLA proceeded, the degree of crystallinity, spherulite size and lamellar thickness increased, and the interlamellar and interspherulitic connections became weaker. These led to the large plastic deformation in the matrix during tension being suppressed, and cracks appeared easily under tensile load, which was favorable to fracture for the blend during tension and so a small elongation at break was obtained. However, the elongation at break for all the annealed specimens was higher than that for neat amorphous PLA, suggesting that PEBA still showed a toughening effect for PLA under annealing. © 2012 Society of Chemical Industry     

Crystallization behavior of fully biodegradable poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Both poly(lactic acid) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) are fully biodegradable polyesters. The disadvantages of poor mechanical properties of PLA limit its wide application. Fully biodegradable polymer blends were prepared by blending PLA with PBAT. Crystallization behavior of neat and blended PLA was investigated by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WAXD). Experiment results indicated that in comparison with neat PLA, the degree of crystallinity of PLA in various blends all markedly was increased, and the crystallization mechanism almost did not change. The equilibrium melting point of PLA initially decreased with the increase of PBAT content and then increased when PBAT content in the blends was 60 wt % compared to neat PLA. In the case of the isothermal crystallization of neat PLA and its blends at the temperature range of 123–142°C, neat PLA and its blends exhibited bell shape curves for the growth rates, and the maximum crystallization rate of neat PLA and its blends all depended on crystallization temperature and their component. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Kinetics and crystal structure of isothermal crystallization of poly(lactic acid) plasticized with triphenyl phosphate

In this article, the spherulitic growth rate of neat and plasticized poly(lactic acid) (PLA) with triphenyl phosphate (TPP) was measured and analyzed in the temperature range of 104–142°C by polarizing optical microscopy. Neat PLA had the maximum value of 0.28 μm/s at 132°C, whereas plasticized PLA had higher value than that of neat PLA, but the temperature corresponding to the maximum value was shifted toward lower one with increasing TPP content. The isothermal crystallization kinetics of neat and plasticized PLA was also analyzed by differential scanning calorimetry and described by the Avrami equation. The results showed for neat PLA and its blends with various TPP contents, the average value of Avrami exponents n were close to around 2.5 at two crystallization temperatures of 113 and 128°C, the crystallization rate constant k was decreased, and the half‐life crystallization time t_1/2 was increased with TPP content. For neat PLA and its blend with 15 wt % TPP content, the average value of n was 2.0 and 2.3, respectively, the value of k was decreased, and the value of t_1/2 was increased with crystallization temperature (T_c). Further investigation into crystallization activation energy ΔE_a of neat PLA and its blend with 15 wt % TPP showed that ΔE_a of plasticized PLA was increased compared to neat PLA. It was verified by wide‐angle X‐ray diffraction that neat PLA and its blends containing various TPP contents crystallized isothermally in the temperature range of 113–128°C all form the α‐form crystal. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) copolymer on the properties of polylactide/poly(methyl methacrylate) blend

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) P(S‐co‐GMA) copolymer on the properties of melt blended polylactide/poly(methyl methacrylate) (PLA/PMMA) 80/20 (wt %) composition was studied. In the literature high ductility levels were achieved by melt blending PLA with different additives. However, the gained ductility was counter balanced with drastic drops in strength and modulus values. The novelty of this work was the preparation of PLA‐based blends with polylactide content higher than 75 wt % which showed an impact resistance value improvement of about 60% compared with the neat PLA and maintained similar tensile strength and modulus values as well as glass transition temperature to neat PLA. The addition of only 3 pph of copolymer to PLA/PMMA blend improved the impact resistance almost 100%. The chemical reaction between PLA/PMMA blend and P(S‐co‐GMA) copolymer were analyzed by FTIR, rotational rheometry, and GPC/SEC. Phase structure and morphology were studied by Differential Scanning Calorimetry and Scanning Electronic Microscopy. Tensile and impact properties as well as thermal stability were also studied. Results showed that as the amount of copolymer in the blend was increased then higher was average molecular weight and polydispersity index. After the addition of P(S‐co‐GMA) copolymer to the PLA/PMMA blend the impact resistance, elongation at break and thermal stability were improved while tensile strength and elastic modulus remained almost unaltered. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43935.     

Toughening of poly(lactide) using polyethylene glycol methyl ether acrylate: Reactive versus physical blending

To design high‐performance poly(lactide)‐based materials (PLA‐based) with improved toughness, two approaches based on the reactive extrusion (REx) process are investigated and compared in the present study. The first approach relies upon a two‐step procedure using a REx‐polymerized poly(ethylene glycol) methyl ether acrylate, i.e., poly(AcrylPEG), as a highly‐branched and compatible impact modifier for PLA. The free‐radical polymerization proves to be very efficient with a peroxide initiator concentration of 1 wt%. The as‐produced poly(AcrylPEG) is then melt‐blended with PLA by extrusion. The resulting materials exhibit largely increase impact resistance (ca. 35 kJ/m²) in presence of 20 wt% poly(AcrylPEG) in comparison with neat PLA (2.7 kJ/m²), while moderate ductility (tensile elongation at break <40%) and limited plasticization effect are observed. The second “one‐step” approach consists in in situ grafting of AcrylPEG onto PLA backbone via a one‐stage REx. The resulting materials exhibit substantially improved impact resistance (ca. 102 kJ/m²) for AcrylPEG loading of 20 wt%, high ductility (tensile elongation at break of ca. 150%) and efficient plasticization. A detailed characterization of the morphology of the materials has been performed using PF‐QNM‐AFM to better elucidate the structure‐property relationships. POLYM. ENG. SCI., 55:1408–1419, 2015. © 2015 Society of Plastics Engineers     

Crystallization behavior of α‐cellulose short‐fiber reinforced poly(lactic acid) composites

The isothermal crystallization behavior of α‐cellulose short‐fiber reinforced poly(lactic acid) composites (PLA/α‐cellulose) was examined using a differential scanning calorimeter and a petrographic microscope. Incorporating a natural micro‐sized cellulose filler increased the spherulite growth rate of the PLA from 3.35 μm/min for neat PLA at 105°C to a maximum of 5.52 μm/min for the 4 wt % PLA/α‐cellulose composite at 105°C. In addition, the inclusion of α‐cellulose significantly increased the crystallinities of the PLA/α‐cellulose composites. The crystallinities for the PLA/α‐cellulose composites that crystallized at 125°C were 48–58%, higher than that of the neat PLA for ～13.5–37.2%. The Avrami exponent n values for the neat and PLA/α‐cellulose composites ranged from 2.50 to 2.81 and from 2.45 to 3.44, respectively, and the crystallization rates K of the PLA/α‐cellulose composites were higher than those of the neat PLA. The activation energies of crystallization for the PLA/α‐cellulose composites were higher than that of the neat PLA. The inclusion of α‐cellulose imparted more nucleating sites to the PLA polymer. Therefore, it was necessary to release additional energy and initiate molecular deposition. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of polylactide‐block‐poly(butylene adipate) polyurethane thermoplastic elastomer

Polylactide‐block‐poly(butylene adipate) poly(ester‐urethane) (PLAEU) thermoplastic elastomer was obtained by melt chain extending reaction with polylactide‐block‐poly(butylene adipate)‐block‐polylactide (PBLA) and hexamethylene diisocyanate (HDI). PBLA was previously prepared with L ‐lactide and poly(butylene adipate) diol (PBA diol). Experimental parameters including feed ratio, polymerization temperature, and time were optimized. The weight average molecular weight (M_w) of PLAEU surpassed 10⁵ g/mol. In contrast to corresponding PBLA, the crystallinity and melt temperature (T_m) of PLAEU decreased, whereas its glass transition (T_g) shifted to high temperature due to the “pseudoextension” structure of polylactide (PLA) block. Additionally, the crystallinity and T_m of PLAEU were subject to crystallization method and molecular weight. The tensile strength of PLAEU varied from 6.61 to 24.41 MPa and elongation from 190% to 780%. Therefore, the mechanical properties of PLAEU can be regulated by altering the length ratio of PLA to PBA block. The high elasticity of PLAEU can be explained with phase separation mechanism. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Synthesis and characterization of fluorinated poly(etherimide)s toughening for carbon fiber‐reinforced epoxy composites

Novel‐fluorinated poly(etherimide)s (FPEIs) with controlled molecular weights were synthesized and characterized, which were used to toughen epoxy resins (EP/FPEI) and carbon fiber‐reinforced epoxy composites (CF/EP/FPEI). Experimental results indicated that the FPEIs possessed outstanding solubility, thermal, and mechanical properties. The thermally cured EP/FPEI resin showed obviously improved toughness with impact strength of 21.1 kJ/m² and elongation at break of 4.6%, respectively. The EP/FPEI resin also showed outstanding mechanical strength with tensile strength of 91.5 MPa and flexural strength of 141.5 MPa, respectively. The mechanical moduli and thermal property of epoxy resins were not affected by blending with FPEIs. Furthermore, CF/EP/FPEI composite exhibited significantly improved toughness with Mode I interlaminar fracture toughness (G_IC) of 899.4 J/m² and Mode II interlaminar fracture toughness (G_IIC) of 1017.8 J/m², respectively. Flexural properties and interlaminar shear strength of the composite were slightly increased after toughening. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Miscibility and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)/phenoxy blends

Miscibility and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST)/poly(hydroxyl ether biphenyl A) (phenoxy) blends were investigated with various techniques in this work. PBST and phenoxy are completely miscible as evidenced by the single composition‐dependent glass transition temperature over the entire blend compositions. Nonisothermal melt crystallization peak temperature is higher in neat PBST than in the blends at a given cooling rate. Isothermal melt crystallization kinetics of neat and blended PBST was studied and analyzed by the Avrami equation. The overall crystallization rate of PBST decreases with increasing crystallization temperature and the phenoxy content in the PBST/phenoxy blends; however, the crystallization mechanism of PBST does not change. Moreover, blending with phenoxy does not modify the crystal structure but reduces the crystallinity degree of PBST in the PBST/phenoxy blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal,mechanical, and rheological properties of plasticized poly(L‐lactic acid)

Polylactide (PLA) is an attractive candidate for replacing petrochemical polymers because it is biodegradable. In this study, a specific PLA 2002D was melt‐mixed with a new plasticizer: glycerol monostearate (GMS). The PLA/GMS blends with different ratios were analyzed by dynamic mechanical analysis and differential scanning calorimetry. Although a slightly phase separation can be seen in DSC curves, the SEM micrographs of the impact fracture surfaces of PLA/GMS blends had a relatively good separation and this phenomenon was in good agreement with their higher impact strength. The result showed that the adding of GMS has enhanced the flexibility of PLA/GMS blends as compared to neat PLA. The relationship between complex viscosity and angular frequency of the PLA/GMS blends exhibits that the melt viscosity substantially lower than that of neat PLA. For example, at 10 rad/s, the melt viscosity of PLA/GMS (85/15) was reduced by about 7.2% compared to that of neat PLA. The impact strength was changed from 4.7 KJ/m² for neat PLA to 48.2 KJ/m² for 70/30 PLA/GMS blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Blends of polylactide and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with low content of hydroxyvalerate unit: Morphology,structure, and property

The Polylactide (PLA)/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) blends with four different weight ratios were prepared by melt mixing. PLA and PHBV in PLA/PHBV blends were immiscible while the weak interaction between PLA and PHBV existed. The PHBV domains below 2 μm were dispersed in PLA matrix uniformly. The addition of PHBV made the crystallization of PLA easier due to PHBV acting as nucleating agent. PLA spherulites in PLA/PHBV blends presented various banded structures. In addition, the crystallinity of neat PLA was lower than those of PLA/PHBV blends. With the increase of PHBV content in PLA/PHBV blends, the crystallinity of PLA/PHBV blends increased. PHBV could enhance significantly the toughness of PLA. However, with the increase of PHBV content, the yield stress (σ_y), tensile modulus (E), and the yield strain (ε_y) of PLA/PHBV blends decreased gradually. In addition, incorporation of PHBV to PLA caused a transformation from an optical transparent to an opaque system. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42689.     

Super‐toughened poly(l‐lactic acid) fabricated via reactive blending and interfacial compatibilization

Super‐toughened poly(l ‐lactic acid) (PLLA) was prepared by reactive blending of PLLA with poly(?‐caprolactone) (PCL), glycerol and 4,4′‐methylenediphenyl diisocyanate. The reactive interfacial compatibility between PLLA and the formed crosslinked polyurethane (CPU) in the PLLA matrix was studied in detail. The morphology and the toughness of the blends can be tuned by changing the CPU content. The results indicate that the impact strength of PLLA shows a tendency to higher values with the increasing PCL content up to 20 wt%. The notched impact strength of the blend with 20 wt% PCL increases to 55.01 kJ m^?2, which is 24.9 times higher than that of neat PLLA. The elongation at break is also increased from 5% to 139.4%, indicating the brittle ? ductile transition. The increased interfacial binding strength through the reactive interfacial compatibility and the formation of a CPU network in the PLLA matrix account for the improved toughness of PLLA/CPU blends. Dynamic mechanical analysis results indicate that the compatibility between PLLA and CPU is improved with increasing CPU content resulting in the formation of more interfacial phase. In addition, rheological property measurements indicate that the improvement in storage modulus and complex viscosity is ascribed to the formation of a CPU network in the PLLA matrix. © 2016 Society of Chemical Industry     

Mechanical and fracture behavior of an artificially ultraviolet‐irradiated poly(ethylene‐carbon monoxide) copolymer

In this work, 1 wt % carbon monoxide (CO) poly(ethylene‐carbon monoxide) (ECO) copolymer sheets were artificially exposed to ultraviolet (UV) light with a power density of 3 mW/cm² for up to 130 h. A thorough mechanical characterization of the irradiated material was conducted, in which both the stress–strain data and the values of the quasistatic crack initiation and growth toughness were measured and correlated with companion uniaxial tensile tests and single‐edge‐notched fracture tests. Average values of the elastic modulus, failure strain, and failure stress were determined from the tensile tests. The full‐field optical technique of digital image correlation was used to quantify in‐plane deformation (displacements and displacement gradients) during the fracture experiments and to extract values of the crack initiation and growth fracture toughness. The elastic modulus increased monotonically with UV irradiation for the exposure times used in this investigation. In addition, for low irradiation times of less than 5 h, both the failure strain and failure stress of ECO decreased, and this caused a corresponding decrease in the crack initiation and growth toughness. However, for longer irradiation times, the failure strain remained almost invariable, whereas the failure stress increased by about 25% over that of unirradiated ECO. As a result, for longer irradiation times (>5 h), 1 wt % CO ECO became not only stiffer but also stronger and tougher, as quantified by companion fracture experiments. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 139–148, 2004     

Enhanced fracture toughness of epoxy resins with novel amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) triblock copolymers

Amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) (PES‐CTBN‐PES) triblock copolymers with controlled molecular weights of 15,000 (15K) or 20,000 (20K) g/mol were synthesized from amine‐terminated PES oligomer and commercial CTBN rubber (CTBN 1300x13). The copolymers were utilized to modify a diglycidyl ether of bisphenol A epoxy resin by varying the loading from 5 to 40 wt %. The epoxy resins were cured with 4,4′‐diaminodiphenylsulfone and subjected to tests for thermal properties, plane strain fracture toughness (K_IC), flexural properties, and solvent resistance measurements. The fracture surfaces were analyzed with SEM to elucidate the toughening mechanism. The properties of copolymer‐toughened epoxy resins were compared to those of samples modified by PES/CTBN blends, PES oligomer, or CTBN. The PES‐CTBN‐PES copolymer (20K) showed a K_IC of 2.33 MPa m^0.5 at 40 wt % loading while maintaining good flexural properties and chemical resistance. However, the epoxy resin modified with a CTBN/8K PES blend (2:1) exhibited lower K_IC (1.82 MPa m^0.5), lower flexural properties, and poorer thermal properties and solvent resistance compared to the 20K PES‐CTBN‐PES copolymer‐toughened samples. The high fracture toughness with the PES‐CTBN‐PES copolymer is believed to be due to the ductile fracture of the continuous PES‐rich phases, as well as the cavitation of the rubber‐rich phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1556–1565, 2002; DOI 10.1002/app.10390     

Isothermal crystallization kinetics of biodegradable poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with low‐molecular weight block copolymers

The isothermal crystallization kinetics of biodegradable blends made of poly(lactic acid) (PLA) and poly(ε‐caprolactone) (PCL) compatibilized with two different low molecular weight block copolymers, that is, ε‐caprolactone/tetramethylene ether glycol and ε‐caprolactone/aliphatic polycarbonate (CB), was done. Blends were prepared by melt mixing in an extruder, while isothermal crystallization kinetics and morphologies were investigated by thermal (differential scanning calorimetry) and thermo‐optical (quantitative polarized light optical microscopy [qPLOM]) quantitative methods. Data were analyzed using the Avrami equation, revealing 2D and 3D growth and simultaneous heterogeneous nucleation. The presence of low molecular weight compatibilizers, that is, 2,000 g mol^?1, accelerated the PLA crystallization rate by two to threefold when compared with neat PLA, with high degrees of crystallinity (40–43%) as confirmed by PLOM images. The activation energy (E_a) showed that PCL inhibits PLA crystallization; however, the addition of block copolymers used as compatibilizers of the blends reduced E_a values, increasing the chain mobility of PLA and thus increasing the crystallization rate. POLYM. ENG. SCI., 59:E161–E169, 2019. © 2018 Society of Plastics Engineers     

Synthesis and characterization of bis(4‐cyanato‐3,5‐dimethylphenyl)anisylmethane/epoxy/glass fiber composites

Bis(4‐cyanato‐3,5‐dimethylphenyl)anisylmethane was prepared by treating CNBr with bis(4‐hydroxy‐3,5‐dimethylphenyl)anisylmethane and blended with commercial epoxy resin in different ratios and cured at 120°C for 2 h, 180°C for 1 h, and postcured at 220°C for 1 h using diamino diphenyl methane as curing agent. Castings of neat resin and blends were prepared and characterized. The composite laminates were also fabricated with glass fiber using the same composition. The tensile strength of the composites increased with increase in cyanate content (3, 6, and 9%) from 322 to 355 MPa. The fracture toughness values also increased from 0.7671 kJ/m², for neat epoxy resin, to 0.8615 kJ/m², for 9% cyanate ester‐modified epoxy system. The 10% weight loss temperature of pure epoxy (358°C) was increased to 390°C by the incorporation of cyanate ester resin. The incorporation of cyanate ester up to 9% in the epoxy resin increases the T_g from 143 to 147°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal properties and non‐isothermal crystallization behavior of poly(trimethylene terephthalate)/poly(lactic acid) blends

Thermal properties and non‐isothermal melt‐crystallization behavior of poly(trimethylene terephthalate) (PTT)/poly(lactic acid) (PLA) blends were investigated using differential scanning calorimetry and thermogravimetric analysis. The blends exhibit single and composition‐dependent glass transition temperature, cold crystallization temperature (T_cc) and melt crystallization peak temperature (T_mc) over the entire composition range, implying miscibility between the PLA and PTT components. The T_cc values of PTT/PLA blends increase, while the T_mc values decrease with increasing PLA content, suggesting that the cold crystallization and melt crystallization of PTT are retarded by the addition of PLA. The modified Avrami model is satisfactory in describing the non‐isothermal melt crystallization of the blends, whereas the Ozawa method is not applicable to the blends. The estimated Avrami exponent of the PTT/PLA blends ranges from 3.25 to 4.11, implying that the non‐isothermal crystallization follows a spherulitic‐like crystal growth combined with a complicated growth form. The PTT/PLA blends generally exhibit inferior crystallization rate and superior activation energy compared to pure PTT at the same cooling rate. The greater the PLA content in the PTT/PLA blends, the lower the crystallization rate and the higher the activation energy. Moreover, the introduction of PTT into PLA leads to an increase in the thermal stability behavior of the resulting PTT/PLA blends. Copyright © 2011 Society of Chemical Industry