Thermal,dielectric, and mechanical properties of SiC particles filled linear low‐density polyethylene composites

A thermally conductive linear low‐density polyethylene (LLDPE) composite with silicon carbide (SiC) as filler was prepared in a heat press molding. The SiC particles distributions were found to be rather uniform in matrix at both low and high filler content due to a powder mixing process employed. Differential scanning calorimeter results indicated that the SiC filler decreases the degree of crystallinity of LLDPE, and has no obvious influence on the melting temperature of LLDPE. Experimental results demonstrated that the LLDPE composites displays a high thermal conductivity of 1.48 Wm^?1 K^?1 and improved thermal stability at 55 wt % SiC content as compared to pure LLDPE. The surface treatment of SiC particles has a beneficial effect on improving the thermal conductivity. The dielectric constant and loss increased with SiC content, however, they still remained at relatively low levels (<10² Hz); whereas, the composites showed poorer mechanical properties as compared to pure LLDPE. In addition, combined use of small amount of alumina short fiber and SiC gave rise to improved overall properties of LLDPE composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Thermal and mechanical characterization of linear low‐density polyethylene/wood flour composites

A linear low‐density polyethylene (LLDPE) matrix was modified with an organic peroxide and by a reaction with maleic anhydride (MAn) and was simultaneously compounded with untreated wood flour in a twin‐screw extruder. The thermal and mechanical properties of the modified LLDPE and the resulting composites were evaluated. The degree of crystallinity was reduced in the modified LLDPE, but it increased with the addition of wood flour for the formation of the composites. Significant improvements in the tensile strength, ductility, and creep resistance were obtained for the MAn‐modified composites. This enhancement in the mechanical behavior could be attributed to an improvement in the compatibility between the filler and the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2775–2784, 2003     

Recycled milk pouch and virgin low‐density polyethylene/linear low‐density polyethylene based coir fiber composites

The viability of the thermomechanical recycling of postconsumer milk pouches [a 50 : 50 low‐density polyethylene/linear low‐density polyethylene (LDPE–LLDPE) blend] and their use as polymeric matrices for coir‐fiber‐reinforced composites were investigated. The mechanical, thermal, morphological, and water absorption properties of recycled milk pouch polymer/coir fiber composites with different treated and untreated fiber contents were evaluated and compared with those of virgin LDPE–LLDPE/coir fiber composites. The water absorption of the composites measured at three different temperatures (25, 45, and 75°C) was found to follow Fickian diffusion. The mechanical properties of the composites significantly deteriorated after water absorption. The recycled polymer/coir fiber composites showed inferior mechanical performances and thermooxidative stability (oxidation induction time and oxidation temperature) in comparison with those observed for virgin polymer/fiber composites. However, a small quantity of a coupling agent (2 wt %) significantly improved all the mechanical, thermal, and moisture‐resistance properties of both types of composites. The overall mechanical performances of the composites containing recycled and virgin polymer matrices were correlated by the phase morphology, as observed with scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of perfluoroalkylmethacrylate ester‐grafted‐linear low‐density polyethylene on the tribological property of polyoxymethylene–linear low‐density polyethylene composites

In this work, perfluoroalkylmethacrylate ester (PFAMAE)‐grafted‐linear low‐density polyethylene (LLDPE) was synthesized by UV‐induced surface graft polymerization. The effect of PFAMAE‐grafted‐LLDPE on the tribological behavior of LLDPE‐filled polyoxymethylene (POM) composite was investigated using a friction and abrasion testing machine. The results showed that LLDPE‐g‐PFAMAE was a more effective modifier in improving tribological property of LLDPE‐filled POM composite than conventional maleic anhydride‐grafted‐polyethylene (PE‐g‐MAH). POM/LLDPE composite possessed much lower friction coefficient but higher wear rate than pristine POM. The incorporation of LLDPE‐g‐PFAMAE into POM/LLDPE further decreased the friction coefficient, which was 45% lower than that of POM. The wear rate of POM/LLDPE/LLDPE‐g‐PFAMAE composite was also reduced and was lower than that of pristine POM. The primary wear mechanisms of POM/LLDPE composite with and without LLDPE‐g‐PFAMAE were adhesive and abrasive wear. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Melt strength of linear low‐density polyethylene/low‐density polyethylene blends

Linear low‐density polyethylenes and low‐density polyethylenes of various compositions were melt‐blended with a batch mixer. The blends were characterized by their melt strengths and other rheological properties. A simple method for measuring melt strength is presented. The melt strength of a blend may vary according to the additive rule or deviate from the additive rule by showing a synergistic or antagonistic effect. This article reports our investigation of the parameters controlling variations of the melt strength of a blend. The reciprocal of the melt strength of a blend correlates well with the reciprocal of the zero‐shear viscosity and the reciprocal of the relaxation time of the melt. An empirical equation relating the maximum increment (or decrement) of the melt strength to the melt indices of the blend components is proposed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1408–1418, 2002     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Calendered linear low‐density polyethylene consolidated meat and bone meal composites

Bioplastics produced from meat and bone meal (MBM) suffer from rapid and drastic mechanical property deterioration because of their hydrophilic nature. This study investigates mechanical and water stability of composites produced from introduction of a minor component of a synthetic polyethylene as a binder phase to consolidate MBM. The milled and sieved MBM was compounded with 5–60 wt % linear low‐density polyethylene (LLDPE) and formed into composite sheets by calendering, which is an industrially relevant process. Results indicated that a minimum of 15 wt % LLDPE content was required to form a nominally continuous binder phase that allowed for good processability and environment stability of the composites. As expected, the water vapor permeability (WVP) and water absorption characteristics of the composites were intermediate between those of MBM and LLDPE. Sheets containing 15 wt % LLDPE absorbed up to 35 wt % water. Composites tested after being soaked in water showed an initial decrease in TS of about 30% for the first hour but then remained fairly unchanged in the next 72 hours, confirming their moderate environment stability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41145.     

Thermal and dielectric properties of the aluminum particle/epoxy resin composites

Microsized aluminum/epoxy resin composites were prepared, and the thermal and dielectric properties of the composites were investigated in terms of composition, aluminum particle sizes, frequency, and temperature. The results showed that the introduction of aluminum particles to the composites hardly influenced the thermal stability behavior, and decreased T_g of the epoxy resin; moreover, the size, concentration, and surface modification of aluminum particles had an effect on their thermal conductivity and dielectric properties. The dielectric permittivity increased smoothly with a rise of aluminum particle content, as well as with a decrease in frequency at high loading with aluminum particles. While the dissipation factor value increased slightly with an increase in frequency, it still remained at a low level. The dielectric permittivity and loss increased with temperature, owing to the segmental mobility of the polymer molecules. We found that the aluminum/epoxy composite containing 48 vol % aluminum‐particle content possessed a high thermal conductivity and a high dielectric permittivity, but a low loss factor, a low electric conductivity, and a higher breakdown voltage. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Blend of high‐density polyethylene and a linear low‐density polyethylene with compositional‐invariant mechanical properties

This article presents the tensile properties and morphological characteristics of binary blends of the high‐density polyethylene (HDPE) and a linear low‐density polyethylene (LLDPE). Two constituents were melt blended in a single‐screw extruder. Injection‐molded specimens were evaluated for their mechanical properties by employing a Universal tensile tester and the morphological characteristics evaluated by using a differential scanning calorimeter and X‐ray diffractometer. It is interesting to observe that the mechanical properties remained invariant in the 10–90% LLDPE content. More specifically, the yield and breaking stresses of these blends are around 80% of the corresponding values of HDPE. The yield elongation and elongation‐at‐break are around 65% to corresponding values of HDPE and the modulus is 50% away. Furthermore, the melting endotherms and the crystallization exotherms of these blends are singlet in nature. They cluster around the corresponding thermal traces of HDPE. This singlet characteristic in thermal traces entails cocrystallization between these two constituting components. The clustering of thermal traces of blends near HDPE meant HDPE‐type of crystallites were formed. Being nearly similar crystallites of blends to that of HDPE indicates nearness in mechanical properties are observed. The X‐ray diffraction data also corroborate these observations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2604–2608, 2002     

Preparation and characterization of linear low‐density polyethylene/low‐density polyethylene/TiO2 membranes

Because of their special functions, the application of nanoscale powders has recently attracted both industrial and theoretical interest. In this study, nanoscale TiO₂, which exhibited a special UV absorption and consequent antibacterial function, was added to a low‐density polyethylene/linear low‐density polyethylene hybrid by melt compounding to yield functional composite membranes. TiO₂ exhibited an apparent induced nucleation effect on the crystallization of polyethylene, and the size of the crystallites decreased while the number increaed with the introduction of TiO₂; however, the crystallinity of polyethylene changed little. Also, TiO₂ exhibited an ideal dispersion in the membrane with an average size less than 100 nm, and this excellent dispersion provided the membranes extra UV absorption; moreover, the transparency of the membranes was maintained to satisfy common requirements. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 216–221, 2005     

Effect of blending high‐pressure low‐density polyethylene on the crystallization kinetics of linear low‐density polyethylene

It is well known that the addition of a small amount of high‐pressure low‐density polyethylene (HP‐LDPE) to linear low‐density polyethylene (LLDPE) can improve the optical properties of LLDPE, and LLDPE/HP‐LDPE blend is widely applied to various uses in the field of film. The optical haziness of polyethylene blown films, as a result of surface irregularities, is thought to be as a consequence of the different crystallization mechanisms. However, not much effort has been directed toward understanding the effect of HP‐LDPE blending on the overall crystallization kinetics (k) of LLDPE including nucleation rate (n) and crystal lateral growth rate (v). In this study, we investigated the effect of blending 20% HP‐LDPE on the crystallization kinetics of LLDPE polymerized by Ziegler‐Natta catalyst with comonomer of 1‐butene. Furthermore, by combining depolarized light intensity measurement (DLIM) and small‐angle laser light scattering (SALLS), we have established a methodology to estimate the lateral growth rate at lower crystallization temperatures, in which direct measurement of lateral growth by polarized optical microscopy (POM) is impossible due to the formation of extremely small spherulites. This investigation revealed that HP‐LDPE blending leads to enhanced nucleation rate, reduced crystal lateral growth rate, and a slight increase in the overall crystallization kinetics of pure LLDPE. From the estimated crystal lateral growth rate, it was found that the suppression in v from HP‐LDPE blending is larger at lower temperatures than at higher temperatures. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Mechanical properties and water absorption of low‐density polyethylene/sawdust composites

The mechanical properties and water absorption of low‐density polyethylene/sawdust composites were investigated. The relationship between the filler content and the composite properties was also studied. Different degrees of esterification of the sawdust with maleic anhydride were obtained with different reaction times. The experimental results demonstrated that the treatment of sawdust by maleic anhydride enhanced the tensile and flexural strengths. The water absorption for maleic anhydride treated sawdust indicated that it was more hydrophobic than untreated sawdust. The effects of the addition of benzoyl peroxide during the preparation of composite samples on the water absorption and mechanical properties were also evaluated. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal analysis of high‐density polyethylene and low‐density polyethylene with enhanced biodegradability

The thermal properties of high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) filled with different biodegradable additives (Mater‐Bi AF05H, Cornplast, and Bioefect 72000) were investigated with thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The DSC traces of the additives indicated that they did not undergo any significant phase change or transition in the temperature region typically encountered by a commercial composting system. The TGA results showed that the presence of the additive led to a thermally less stable matrix and higher residue percentages. The products obtained during the thermodegradation of these degradable polyolefins were similar to those from pure polyethylenes. The LDPE blends were thermally less stable than the HDPE blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 764–772, 2002     

Effects of ultrasonic oscillations on processing behavior and mechanical properties of metallocene‐catalyzed linear low‐density polyethylene/low‐density polyethylene blends

The influences of ultrasonic oscillations on rheological behavior and mechanical properties of metallocene‐catalyzed linear low‐density polyethylene (mLLDPE)/low‐density polyethylene (LDPE) blends were investigated. The experimental results showed that the presence of ultrasonic oscillations can increase the extrusion productivity of mLLDPE/LDPE blends and decrease their die pressure and melt viscosity during extrusion. Incorporation of LDPE increases the critical shear rate for sharkskin formation of extrudate, crystallinity, and mechanical properties of mLLDPE. The processing behavior and mechanical properties of mLLDPE/LDPE blends were further improved in the presence of ultrasonic oscillations during extrusion. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2522–2527, 2004     

Rheology of low‐density polyethylene + Boehmite composites

Polyethylene is already one of the most commonly used polymers due to its solvent resistance and easy processing. Low‐density polyethylene (LDPE) also has excellent flexibility and resilience. However, the mechanical properties of LDPE are often poor. We added the inexpensive ceramic filler Boehmite to LDPE, simultaneously improving mechanical properties and reducing production cost—as Boehmite is cheap and abundant while the filler reduces the amount of petroleum‐derived polymer per unit weights of product. Additionally, less environmental contamination results at the end of service life since the Boehmite need not undergo degradation as the LDPE does. To aid adhesion between the matrix and filler, we introduced silane coupling agents (SCAs) to bond the hydrophobic LDPE to the hydrophilic Boehmite. Furthermore, since fillers ordinarily increase viscosity, it was essential to maintain a low viscosity for easy processability. We evaluated by rheometry the effect of the Boehmite on the melt viscosity of the LDPE + Boehmite composites and determined that the addition of any type of Boehmite decreases the viscosity compared to that of neat LDPE. The effects were explained by fiber formation and enhanced rigidity while the allowance for a lower processing temperature results in further energy and therefore cost savings. We also show that high‐temperature exposure of Boehmite during any part of the sample processing results in a decrease in the coupling efficiency of the matrix to filler and in a higher melt viscosity; yet the viscosity is still lower than for neat LDPE. POLYM. COMPOS., 31:1909–1913, 2010. © 2010 Society of Plastics Engineers.     

Spherulitic crystallization behavior of linear low‐density polyethylene

In this study the crystallization behavior of linear low‐density polyethylenes (LLDPEs) (ethylene‐α‐olefin copolymers) was studied by polarized light microscopy. A modified Hoffman‐Lauritzen (MHL) expression is proposed whereby the equilibrium melting temperature, T (T), is replaced with the melting temperature of the crystal stem is replaced with the maximum possible stem length, T. It successfully describes the crystalline spherulitic growth kinetics for both homogeneous and heterogeneous LLDPEs. In addition to regimes III and II, another regime (IM) was found in the high crystallization temperature range. Linear growth behavior of crystalline spherulites was observed in regime III, and nonlinear growth behavior was found in regimes II and IM. The basal surface free energy can be estimated from the short chain branching polydispersity (SCBP) for LLDPEs with excluded comonomers. Polym. Eng. Sci. 45:74–83, 2005. © 2004 Society of Plastics Engineers.     

Microwave absorbing properties of ternary linear low‐density polyethylene/carbonyl iron powder/carbon black composites

Linear low‐density polyethylene (LLDPE) was used as polymer matrix, carbonyl iron powder (CIP) and carbon black (CB) were used as fillers, and ternary composites with microwave absorbing properties were prepared by melt blending. Transmission electron microscopy was used to characterize the prepared samples. The absorbing ability (reflection loss) of the prepared composites was measured using the arch method, and the electromagnetic parameters of composites were determined by the transmission/reflection method. The filler contents of CIP and CB have effects on the absorbing peak positions and reflection loss, and there is the optimum filler content in composites to obtain the maximum microwave absorbing. The microwave absorption of LLDPE/CIP/CB composites comes from the combining contributions of the dielectric loss and the magnetic loss. The synergistic effects of CIP and CB effectively improve the microwave absorbing properties of polymer composites. CIP and CB are uniformly distributed in the polymer matrix. The theoretical calculation results of the absorbing ability are in agreement with the experimental results using the transmission line theory. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical and shape‐memory properties of polyamide/maleated polyethylene/linear low‐density polyethylene blend

Novel polymer blends of polyamide and linear low‐density polyethylene with maleated polyethylene as compatibilizers were prepared in a modular intermeshing corotating twin‐screw extruder. Polymer blends with different contents of polyamide in polyethylene matrix were obtained. The mechanical properties were studied in terms of the tensile strength and elongation‐to‐break. The shape‐memory properties of the blended materials were characterized using three‐point bending test in a temperature‐controlled chamber. The results show that the incorporation of maleated polyethylene has a strong effect on the tensile properties and the morphology of the blends. The shape‐memory effect of blended materials is affected by polyamide weight fraction, and 60 wt % polyethylene, 20 wt % polyamide, and 20% maleated polyethylene have an acceptable performance. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of low‐density polyethylene/thermoplastic starch composites reinforced by cellulose nanofibers

In the current study, the effect of extracted cellulose nanofibers (CNFs) on rheological and mechanical properties and biodegradability of polyethylene/starch blend was investigated. The CNFs were extracted from wheat straws using a chemo‐mechanical method. Polyethylene/starch blend was reinforced by different amounts of CNF (6–14 wt%) using an internal mixer followed by a single screw extruder. The flow properties of nanocomposites were investigated by determining Melt Flow Index (MFI) and viscosity. Due to the weak interaction of cellulosic nanofibers and polymers, the flow behavior of nanocomposites was undesirable. Tensile tests were performed to evaluate the mechanical performance of nanocomposites. By increasing the CNF content, the tensile strength and elongation at break declined; whereas, the Young's modulus was improved. The biodegradation of cellulose nanocomposites was investigated by water absorption and degradability tests. Both experiments confirmed the progressive effect of cellulose nanofibers on the degradation of the composites. POLYM. COMPOS., 36:2309–2316, 2015. © 2014 Society of Plastics Engineers