Compatible and crystallization properties of poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and dynamic mechanical analysis (DMA) properties of poly(lactic acid)/ poly(butylene adipate‐co‐terephthalate) (PLA/PBAT) specimens suggest that only small amounts of poor PLA and/or PBAT crystals are present in their corresponding melt crystallized specimens. In fact, the percentage crystallinity, peak melting temperature and onset re‐crystallization temperature values of PLA/PBAT specimens reduce gradually as their PBAT contents increase. However, the glass transition temperatures of PLA molecules found by DSC and DMA analysis reduce to the minimum value as the PBAT contents of PLA_xPBAT_y specimens reach 2.5 wt %. Further morphological and DMA analysis of PLA/PBAT specimens reveal that PBAT molecules are miscible with PLA molecules at PBAT contents equal to or less than 2.5 wt %, since no distinguished phase‐separated PBAT droplets and tan δ transitions were found on fracture surfaces and tan δ curves of PLA/PBAT specimens, respectively. In contrast to PLA, the PBAT specimen exhibits highly deformable properties. After blending proper amounts of PBAT in PLA, the inherent brittle deformation behavior of PLA was successfully improved. Possible reasons accounting for these interesting crystallization, compatible and tensile properties of PLA/PBAT specimens are proposed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry     

Polymorphism and properties of biodegradable poly(1,4‐butylene adipate) tailored using an aliphatic diamide derivative

N,N′‐Ethylenebis(12‐hydroxystearamide) (EBH), an aliphatic diamide organic compound with environmental friendliness, was selected as an effective nucleating agent to be incorporated into poly(1,4‐butylene adipate) (PBA) polyester. EBH increased the crystallization temperature, crystallinity, crystal density and thermal stability, and shortened the crystallization time of PBA. EBH slowed down the critical temperature of the PBA α‐crystal, accelerated the β‐to‐α phase transition rate and tailored the polymorphic crystalline structure of the PBA probably via the interfacial interaction and/or crystal lattice matching between PBA and EBH. In the presence of EBH, the degradation rate of PBA decreased. The mechanisms of the nucleation, manipulation of the crystal type, accelerated β‐to‐α phase transition, enhanced thermal stability and decreased enzymatic degradation rate of PBA are proposed and discussed in detail. © 2018 Society of Chemical Industry     

Micromorphology,mechanical, crystallization and permeability properties analysis of HA/PBAT/PLA (HA,hydroxyapatite; PBAT,poly(butylene adipate‐co‐butylene terephthalate); PLA,polylactide) degradability packaging films

In this study, the self‐made nano‐hydroxyapatite (HA) and poly(butylene adipate‐co‐butylene terephthalate) copolyesters (PBAT) were used as fillers, and composite films of HA/PLA (PLA, polylactide) and HA/PBAT/PLA systems were prepared. The micromorphology, mechanical properties, thermal properties, crystallinity, water vapor permeability and oxygen permeability of the composite films were studied. The results show that the self‐made HA has a porous rod‐like structure with a size of 30–50 nm. PBAT was dispersed uniformly in the HA/PLA matrix in the form of spherical particles and formed many pores and holes. The tensile strength, elongation at break and modulus of elasticity of HA/PLA composite films were increased by adding 10 wt% PBAT. The addition of HA and PBAT played a synergistic function in improving the crystallinity of the composite films. The water vapor and oxygen permeabilities of HA/PLA and HA/10%PBAT/PLA composite films can be regulated by adjusting the amount of HA. The results of this study indicate that composite films with higher water vapor and oxygen permeabilities exhibit great potential for applications in green packaging and fresh‐keeping packaging. © 2019 Society of Chemical Industry     

Copolymers based on poly(butylene terephthalate) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone

A series of novel thermoplastic elastomers, based on poly(butylene terephthalate) (PBT) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone (PCL‐PDMS‐PCL), with various mass fractions, were synthesized through melt polycondensation. In the synthesis of the poly(ester‐siloxane)s, the PCL blocks served as a compatibilizer for the non‐polar PDMS blocks and the polar comonomers dimethyl terephthalate and 1,4‐butanediol. The introduction of PCL‐PDMS‐PCL soft segments resulted in an improvement of the miscibility of the reaction mixture and therefore in higher molecular weight polymers. The content of hard PBT segments in the polymer chains was varied from 10 to 80 mass%. The degree of crystallinity of the poly(ester‐siloxane)s was determined using differential scanning calorimetry and wide‐angle X‐ray scattering. The introduction of PCL‐PDMS‐PCL soft segments into the polymer main chains reduced the crystallinity of the hard segments and altered related properties such as melting temperature and storage modulus, and also modified the surface properties. The thermal stability of the poly(ester‐siloxane)s was higher than that of the PBT homopolymer. The inclusion of the siloxane prepolymer with terminal PCL into the macromolecular chains increased the molecular weight of the copolymers, the homogeneity of the samples in terms of composition and structure and the thermal stability. It also resulted in mechanical properties which could be tailored. Copyright © 2010 Society of Chemical Industry     

Synthesis of poly(lactic acid)‐based polyurethanes

Poly(lactic acid) (PLA) is a biodegradable aliphatic polyester, but its brittleness makes it unsuitable for many packaging and appliance applications. The goal of the work reported was to create novel poly(ester urethane)s that incorporate biodegradable poly(lactic acid) diols (PLA‐OHs) and good mechanical properties of increased molecular weight via crosslinked network formation for engineering plastics applications. Three kinds of polyols (PLA‐OHs, PLA‐OHs/poly(tetramethylene ether) glycol or PLA‐OHs/poly(butylene adipate) glycol (PBA)) and two kinds of diisocyanates (4,4‐diphenylmethane diisocyanate (MDI) or toluene 2,4‐diisocyanate (TDI)) were chosen for the soft and hard segments to compare their mechanical properties. In addition, 1,4‐butanediol and trimethylolpropane were each used as chain extender agents. Results showed the PLA/PBA‐polyurethanes (PLA/PBA‐PUs) of the MDI series and the PLA/PBA‐PUs of the TDI series had improved thermal stability and enhanced mechanical properties. Degradation behavior showed the PLA‐based polyurethanes could be degraded in phosphate‐buffered saline solution and enzyme solution. © 2012 Society of Chemical Industry     

Influence of phthalic anhydride and bioxazoline on the mechanical and morphological properties of biodegradable poly(lactic acid)/poly[(butylene adipate)‐co‐terephthalate] blends

Poly(lactic acid) (PLA)/poly[(butylene adipate)‐co‐terephthalate] (PBAT) blends were fabricated by melt blending, with 2,2′‐(1,3‐phenylene)bis(2‐oxazoline) (BOZ) and phthalic anhydride (PA) used as compatibilizers. It was found that a small amount of BOZ or PA greatly increased the elongation at break of the PLA/PBAT blends without sacrificing their high tensile strength. Scanning electron microscopy results revealed that the PBAT particles became finer and were uniformly dispersed in the matrix when the compatibilizers were incorporated, which indicated that the interfacial bonding and compatibilization between PLA and PBAT were improved in the presence of the compatibilizers. Compared with PLA/PBAT blends, the molecular weight of PLA/PBAT/PA/BOZ blends was increased due to chain‐extending reactions. Differential scanning calorimetry results suggested PBAT decreased the crystallization rate and crystallinity of PLA in the blends. Moreover, the glass transition temperature of PBAT was further decreased when the compatibilizers were used. © 2013 Society of Chemical Industry     

Dynamic mechanical and thermal properties of plasticized poly(lactic acid)

The blends of low molecular weight triacetin (TAC) and oligomeric poly(1,3‐butylene glycol adipate) (PBGA) were used as multiple plasticizers to lubricate poly(lactic acid) (PLA) in this study. The thermal and mechanical properties of plasticized polymers were investigated by means of dynamic mechanical analysis and differential scanning calorimetry. Atomic force microscopy (AFM) was used to analyze the morphologies of the blends. Multiple plasticizers were effective in lowering the glass transition temperature (T_g) and the melting temperature (T_m) of PLA. Moreover, crystallinity of PLA increased with increasing the content of multiple plasticizers. Tensile strength of the blends decreased following the increasing of the plasticizers, but increased in elongation at break. AFM topographic images showed that the multiple plasticizers dispersed between interfibrillar regions. Moreover, the fibrillar crystallite formed the quasicrosslinkings, which is another cause for the increase in elongation at break. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1583–1590, 2006     

Polymorphism and spherulite morphology of poly(1,4‐butylene adipate)/organically‐modified layered double hydroxide nanocomposites

A novel biodegradable poly(1,4‐butylene adipate)/organically‐modified layered double hydroxide (PBA/m‐LDH) nanocomposites are synthesized using the solution mixing process. The m‐LDH is originally prepared with magnesium nitrate hexahydrote (Mg(NO₃)₂ 6H₂O), aluminum nitrate‐9‐hydrate (Al(NO₃)₃ 9H₂O), oleic acid, and sorbitol by a novel one‐step co‐precipitation method to intercalate the organo‐modifier of oleic acid and sorbitol into the interlayer of LDH. The structure and morphology of the PBA/m‐LDH nanocomposites are characterized using X‐ray diffraction and transmission electron microscopy (TEM). It has been shown that the m‐LDH is exfoliated and well distributed in PBA matrix. The effect of m‐LDH on the polymorphic crystal and morphology of PBA at various crystallization temperatures (T_cs) would be investigated using WAXD and POM. Both data indicate that the addition of m‐LDH can change the starting formation temperature of α‐form crystals. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42526.     

Crystal behavior of semicrystalline polystyrene‐block‐poly(l‐lactide) diblock copolymer in thin films with various structures

The crystal behavior of a semicrystalline polystyrene‐block‐poly(l ‐lactide) diblock copolymer in phase‐separated thin films with various thicknesses at different crystal temperatures has been investigated using atomic force microscopy and transmission electronic microscopy. Parallel and perpendicular lamellae could be obtained by annealing the thin films for different periods of time as reported previously (Chen et al., Macromolecules 40:6631 (2007)). At different temperatures, crystallization in thin films with parallel lamellar structure in the melt state gives dendrite crystals with orthorhombic structure, and the ordered structure in the melt is destroyed after crystallization. When crystallization occurs in thin films with perpendicular lamellar structure, crystal morphology and structure are greatly affected by the crystallization temperature (T_c). When T_c < T_g,ps, where T_g,ps is the glass transition temperature of a polystyrene block, crystallization is hardly confined within the lamellae. The morphology is preserved but the long period of the perpendicular lamellae is increased after crystallization. When T_c > T_g,ps, rod‐like crystals dominate the final morphology, and crystallinity destroys completely the structure in the melt.© 2012 Society of Chemical Industry     

Polymorphic crystallization of poly(butylene adipate) and its copolymer: Effect of poly(vinyl alcohol)

The crystallization kinetics and crystalline structure of the biodegradable polymorphic polymers, poly(butylene adipate) (PBA) and poly(butylene adipate‐co‐hexamethylene adipate), in the microparticles and nanoparticles covered by poly(vinyl alcohol) (PVA), and those on the PVA substrate were investigated by differential scanning calorimetry, wide‐angle X‐ray diffraction, and Fourier transform infrared spectroscopy. Both the polymers crystallized in the particle state and on the PVA substrate showed higher crystallization temperatures in the nonisothermal melt crystallization and shorter crystallization times in the isothermal crystallization; this indicated a faster crystallization of the polymer in the particle state and on the PVA substrate than that of the bulk sample. Furthermore, the polymers in the particle state and on the PVA substrate showed the preferential formation of the β‐type crystalline form of PBA compared to the bulk one. The mechanism for the effects of the PVA layer or substrate on the crystallization kinetics and crystalline structure of PBA and its copolyesters are discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39600.     

Influence of semi‐crystalline poly(ε‐caprolactone) and non‐crystalline polylactide blocks on the thermal properties of polydimethylsiloxane‐based block copolymers

Poly(A)‐block‐poly(B), poly(A)‐block‐poly(B)‐block‐poly(A) and B(A)₂ block copolymers were prepared through coordinated anionic ring‐opening polymerization of ε‐caprolactone (CL) and lactic acid (LA) using hydroxy‐terminated polydimethylsiloxane (PDMS) as initiator. A wide range of well‐defined combinations of PDMS‐block‐PCL and PDMS‐block‐PLA diblock copolymers, PCL‐block‐PDMS‐block‐PCL and PLA‐block‐PDMS‐block‐PLA triblock copolymers and star‐PDMS(PCL)₂ copolymers were thus obtained. The number‐average molar masses and the structure of the synthesized block copolymers were identified using various analytical techniques. The thermal properties of these copolymers were established using differential scanning calorimetry. Considering PDMS‐block‐PCL copolymers, the results demonstrate the complex effect of polymer architecture and PCL block length on the ability of the PDMS block to crystallize or not. In the case of diblock copolymers, crystallization of PCL blocks originated from stacking of adjacent chains inducing the extension of the PDMS block that can easily crystallize. In the case of star copolymers, the same tendency as in triblock copolymers is observed, showing a limited crystallization of PDMS when the length of the PCL block increases. In the case of PDMS‐block‐PLA copolymers, melting and crystallization transitions of the PLA block are never observed. Considering the diblock copolymers, PDMS sequences have the ability to crystallize. © 2019 Society of Chemical Industry     

Thermal properties and non‐isothermal crystallization behavior of poly(trimethylene terephthalate)/poly(lactic acid) blends

Thermal properties and non‐isothermal melt‐crystallization behavior of poly(trimethylene terephthalate) (PTT)/poly(lactic acid) (PLA) blends were investigated using differential scanning calorimetry and thermogravimetric analysis. The blends exhibit single and composition‐dependent glass transition temperature, cold crystallization temperature (T_cc) and melt crystallization peak temperature (T_mc) over the entire composition range, implying miscibility between the PLA and PTT components. The T_cc values of PTT/PLA blends increase, while the T_mc values decrease with increasing PLA content, suggesting that the cold crystallization and melt crystallization of PTT are retarded by the addition of PLA. The modified Avrami model is satisfactory in describing the non‐isothermal melt crystallization of the blends, whereas the Ozawa method is not applicable to the blends. The estimated Avrami exponent of the PTT/PLA blends ranges from 3.25 to 4.11, implying that the non‐isothermal crystallization follows a spherulitic‐like crystal growth combined with a complicated growth form. The PTT/PLA blends generally exhibit inferior crystallization rate and superior activation energy compared to pure PTT at the same cooling rate. The greater the PLA content in the PTT/PLA blends, the lower the crystallization rate and the higher the activation energy. Moreover, the introduction of PTT into PLA leads to an increase in the thermal stability behavior of the resulting PTT/PLA blends. Copyright © 2011 Society of Chemical Industry     

Hydrolytic degradation of biobased poly(butylene succinate‐co‐furandicarboxylate) and poly(butylene adipate‐co‐furandicarboxylate) copolyesters under mild conditions

It is indispensable to investigate hydrolytic degradation behavior to develop novel (bio)degradable polyesters. Biobased and biodegradable copolyesters poly(butylene adipate‐co ‐butylene furandicarboxylate) (PBAF) and poly(butylene succinate‐co ‐butylene furandicarboxylate) (PBSF) with BF molar fraction (?_BF) between 40 and 60% were synthesized in this study. The hydrolytic degradation of film samples was conducted in a pH 7.0 PBS buffer solution at 25 °C. Slight mass loss (1–2%) but significant decrease in intrinsic viscosity (35–44%) was observed after 22 weeks. The apparent hydrolytic degradation rate decreased with increasing ?_BF and initial crystallinity. Meanwhile, PBAFs degraded slightly faster than PBSFs with the same composition. The ?_BF and crystallinity increased slowly with degradation time, suggesting the aliphatic moiety and the amorphous region are more susceptible to hydrolysis. And high enough tensile properties were retained after hydrolysis degradation, indicating PBAF and PBSF copolyesters are hydrolytically degradable, with tunable hydrolytic degradation rate and good balance between hydrolytic degradability and durability. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44674.     

Synthesis of star‐shaped poly(ε‐caprolactone)‐b‐poly(L‐lactide) copolymers: From star architectures to crystalline morphologies

Hexa‐armed star‐shaped poly(ε‐caprolactone)‐block‐poly(L ‐lactide) (6sPCL‐b‐PLLA) with dipentaerythritol core were synthesized by a two‐step ring‐opening polymerization. GPC and ¹H NMR data demonstrate that the polymerization courses are under control. The molecular weight of 6sPCLs and 6sPCL‐b‐PLLAs increases with increasing molar ratio of monomer to initiator, and the molecular weight distribution is in the range of 1.03–1.10. The investigation of the melting and crystallization demonstrated that the values of crystallization temperature (T_c), melting temperature (T_m), and the degree of crystallinity (X_c) of PLLA blocks are increased with the chain length increase of PLLA in the 6sPCL‐b‐PLLA copolymers. On the contrary, the crystallization of PCL blocks dominates when the chain length of PLLA is too short. According to the results of polarized optical micrographs, both the spherulitic growth rate (G) and the spherulitic morphology are affected by the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Flexible and flame‐retardant S‐SEB‐S triblock copolymer/PPE nano‐alloy

We observed that modified polyphenylene ether (PPE) was solubilized in thermoplastic styrenic elastomer (TPS) and that a two‐phase lacy structure formed on nanometer scales when the TPS composition was 67 wt % and modified PPE and polystyrene‐block‐poly(styrene‐co‐ethylene‐co‐butylene)‐block‐polystyrene (S‐SEB‐S triblock copolymer) were blended. However, the molecular weight of the outer PS block segments M_outPS and the content of the outer PS block segments ?_outPS were <10,000 g/mol and 20 wt %, respectively. The resulting S‐SEB‐S/modified PPE nano‐alloy exhibited both flexibility and flame retardancy, unlike other materials, where a trade‐off exists between these two properties; that is, the flame retardancy was excellent when the phosphorus additive was present. This combination of properties might be attributed to the two‐phase nanometer‐scale structure consisting of flame‐retardant styrene/PPE domains and a continuous soft, lacy SEB matrix. The results for polystyrene‐block‐poly(ethylene‐co‐butylene)‐block‐polystyrene (S‐EB‐S triblock copolymer)/modified PPE blends were presented for comparison. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40446.     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

High performance materials based on a self‐assembled multiple‐percolated ternary blend

In this study, it will be shown that morphologically tailored tricontinuous ternary blends, comprising polybutylene succinate (PBS), polylactic acid (PLA), and poly (butylene adipate‐co‐terephthalate)(PBAT), can generate new materials with excellent properties. Detailed morphological analysis is used to establish that all three phases in the ternary 33%PBS/33%PLA/33%PBAT blend morphology are highly continuous with a phase structure dominated by complete wetting dynamics. PBS is shown to situate itself between PLA and PBAT. This melt processed, self‐assembled, multiple percolated, blend possesses a high elongation at break (567%), high Young's modulus (1130 MPa), high impact strength (271 J/m), and a storage modulus about 50% higher than pure PBS at room temperature. None of the neat materials demonstrate this combination of high properties and the synergy derives from the tricontinuous structure of the system. The ternary nature of the blend allows for a modulation of the crystallinity behavior as examined by differential scanning calorimeter and X‐ray Diffraction. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3005–3012, 2014     

Synthesis and properties of biodegradable supramolecular polymers based on polylactide‐block‐poly(δ‐valerolactone)‐block‐polylactide triblock copolymers

Biodegradable supramolecular polymers (SMPs) were synthesized by the end‐functionalization of polylactide‐block‐poly(δ‐valerolactone)‐block‐polylactide (PLA–PVL–PLA) triblock copolymers with 2‐ureido‐4[1H]‐pyrimidinone (UPy) self‐complementary quadruple hydrogen‐bonding units. The end‐functionalized PLA–PVL–PLA copolymers exhibit the typical characteristics of thermoplastic elastomers. Thermal properties, crystallization behavior, crystalline structure and other properties of SMPs can be adjusted by changing the length and stereostructure of PLA blocks. The UPy groups retard the crystallization of PLA and PVL blocks, and the crystallization of PVL blocks is also depressed with increasing PLA blocks. Tensile testing reveals that the prepared SMPs present excellent mechanical properties, and dynamic mechanical analysis indicates that the heat resistance of l ‐SMPs is better than that of d ,l ‐SMPs. Shape memory property of SMPs was also studied, and the recovery ratio of SMPs with PDLLA blocks can reach 100%. The recovery ratio of l ‐SMPs is depressed as the crystallizable PLLA blocks increase. This study has systemically investigated the effect of the composition, stereostructure and crystallizability of PLA blocks on the properties of SMPs, which would provide potential approaches for the synthesis of biodegradable SMPs with tunable properties. © 2017 Society of Chemical Industry