Structure and properties of polyimide‐g‐nylon 6 and nylon 6‐b‐polyimide‐b‐nylon 6 copolymers

Polyimide‐g‐nylon 6 copolymers were prepared by the polymerization of phenyl 3,5‐diaminobenzoate with several diamines and dianhydrides with a one‐step method. The polyimides containing pendant ester moieties were then used as activators for the anionic polymerization of molten ε‐caprolactam. Nylon 6‐b‐polyimide‐b‐nylon 6 copolymers were prepared by the use of phenyl 4‐aminobenzoate as an end‐capping agent in the preparation of a series of imide oligomers. The oligomers were then used to activate the anionic polymerization of ε‐caprolactam. In both the graft and copolymer syntheses, the phenyl ester groups reacted quickly with caprolactam anions at 120°C to generate N‐acyllactam moieties, which activated the anionic polymerization. All the block copolymers had higher moduli and tensile strengths than those of nylon 6. However, their elongations at break were much lower. The graft copolymers based on 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]propane dianhydride and 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane displayed elongations comparable to that of nylon 6 and the highest moduli and tensile strengths of all the copolymers. The thermal stability, moisture resistance, and impact strength were dramatically increased by the incorporation of only 5 wt % polyimide into both the graft and block copolymers. The graft and block copolymers also exhibited improved melt processability. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 300–308, 2006     

Synthesis and properties of fluorinated polyimides from 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane and various aromatic dianhydrides

A novel aromatic diamine, 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane, containing a pendant polyfluorinated phenyl group, a trifluoromethyl group, and methyl groups ortho‐substituted to the amino groups in the structure was synthesized and characterized. The diamine was polymerized with several aromatic dianhydrides, including 3,3′,4,4′‐biphenyltetracarboxylic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, 4,4′‐oxydiphthalic anhydride, and 4,4′‐hexafluoroisopropylidene diphthalic anhydride, via a high‐temperature one‐step procedure to afford four polyimides (PIs) with inherent viscosities of 0.47–0.70 dL/g. The PIs exhibited excellent solubilities in a variety of organic solvents. They were soluble not only in polar aprotic solvents but in many common solvents, such as cyclopentanone, tetrahydrofuran, and even toluene at room temperature. The tough and flexible PI films cast from the PI solutions exhibited good thermal stabilities and acceptable tensile properties. The glass‐transition temperatures were in the range 312–365°C, and the 5% weight loss temperatures were all higher than 480°C in nitrogen. The films had tensile strengths in the range 76–99 MPa, tensile moduli of 2.2–2.8 GPa, and elongations at break of 5–8%. In addition, the PI films exhibited excellent transparency in the visible light region with cutoff wavelength as low as 302 nm and transmittance higher than 88% at the wavelength of 450 nm. The PI films showed low dielectric constants ranging from 2.50–2.68 and low moisture absorptions of less than 0.56%. The good combined properties of the PIs mainly resulted from the synergic effects of the different substituents. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of organosoluble polyfluorinated polyimides derived from 3,3′,5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane and various aromatic dianhydrides

A polyfluorinated aromatic diamine, 3,3′, 5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane (TFDAM), was synthesized and characterized. A series of polyimides, PI‐1–PI‐4, were prepared by reacting the diamine with four aromatic dianhydrides via a one‐step high‐temperature polycondensation procedure. The obtained polyimide resin had moderate inherent viscosity (0.56–0.68 dL/g) and excellent solubility in common organic solvents. The polyimide films exhibited good thermal stability, with an initial thermal decomposition temperature of 555°C–621°C, a 10% weight loss temperature of 560°C–636°C, and a glass‐transition temperature of 280°C–326°C. Flexible and tough polyimide films showed good tensile properties, with tensile strength of 121–138 MPa, elongation at break of 9%–12%, and tensile modulus of 2.2–2.9 GPa. The polyimide films were good dielectric materials, and surface and volume resistance were on the order of a magnitude of 10¹⁴ and 10¹⁵ Ω cm, respectively. The dielectric constant of the films was below 3.0 at 1 MHz. The polyfluorinated films showed good transparency in the visible‐light region, with a cutoff wavelength as low as 302 nm and transmittance higher than 70% at 450 nm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1442–1449, 2007     

Synthesis,characterization, and properties of new siloxane grafted copolyimides

Three new siloxane containing grafted copolyimides have been prepared by one‐pot solution imidization technique. The polymers are made by the reaction of 4,4′‐(4,4′‐isopropylidenediphenoxy)bis(phthalic anhydride) (BPADA) with commercially available diamine 4,4′‐oxydianiline (ODA) with variation of silicon containing diamine, namely 3,5‐diaminobenzoate terminated polydimethylsiloxane (DBPDMS), as a comonomer to 10, 20, and 30 wt %. The films of the polymers were prepared by casting the polymer solution in dichloromethane. The polymers have been well‐characterized by GPC, IR, and NMR techniques. Thermal stabilities and decomposition behavior of the copolyimides were studied by DSC and TGA. The water contact angle values of the films indicate hydrophobic nature of the polymers. Thermal, flame retardant, mechanical, and surface properties of these polymers have been compared with the homopolyimide and with polyimides where polysiloxane is incorporated in the main chain. DSC revealed melting of the grafted siloxane chain at sub‐ambient temperature and a glass transition corresponding to the main polymer chain above 200°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of Irradiation Temperature on Grafting of Styrene into Poly(tetrafluoroethylene‐co‐hexafluoropropylene) Films

This study concerns with the investigation of the effect of irradiation conditions on grafting of styrene into FEP films by the pre‐irradiation method. EPR spectroscopy was used to characterize the base polymer material regarding the trapped radical species and their concentration. Radiation‐induced changes in the chemical structure were studied by IR spectroscopy. Tensile strength and elongation at break as well as yield of grafting were found to be strongly influenced by irradiation temperature. Main‐chain scissions were identified to be the reason for the deterioration of the mechanical properties after radiation treatment at temperatures below glass transition temperature.

     

Synthesis and characterization of melt‐processable polyimides derived from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene

A series of molecular‐weight‐controlled imide resins end‐capped with phenylethynyl groups were prepared through the polycondensation of a mixture of 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene and 1,3‐bis(4‐aminophenoxy)benzene with 4,4′‐oxydiphthalic anhydride in the presence of 4‐phenylethynylphthalic anhydride as an end‐capping agent. The effects of the resin chemical structures and molecular weights on their melt processability and thermal properties were systematically investigated. The experimental results demonstrated that the molecular‐weight‐controlled imide resins exhibited not only meltability and melt stability but also low melt viscosity and high fluidability at temperatures lower than 280°C. The molecular‐weight‐controlled imide resins could be thermally cured at 371°C to yield thermoset polyimides by polymer chain extension and crosslinking. The neat thermoset polyimides showed excellent thermal stability, with an initial thermal decomposition temperature of more than 500°C and high glass‐transition temperatures greater than 290°C, and good mechanical properties, with flexural strengths in the range of 140.1–163.6 MPa, flexural moduli of 3.0–3.6 GPa, tensile strengths of 60.7–93.8 MPa, and elongations at break as high as 14.7%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis,thermal, and dynamic mechanical properties of 1,3‐bis(diphenylsilyl)‐2,2,4,4‐tetraphenylcyclodisilazane‐containing polydimethylsiloxanes

New and effective approaches to the synthesis of 1,3‐bis(diphenylsilyl)‐2,2,4,4‐tetraphenylcyclodisilazane‐containing polydimethylsiloxanes ( P1 and P2 ) were developed. P1 was obtained by polycondensation of cyclodisilazane lithium salt and chloroterminated polydimethylsiloxane. P2 was produced by hydrosilylation of vinyl‐terminated cyclodisilazane and hydrogen‐terminated polydimethylsiloxane. The polycondensation completed quickly at room temperature, while the hydrosilylation was facile and did not require cumbersome air‐sensitive operations. P1 and P2 were characterized by Fourier transform infrared, nuclear magnetic resonance, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis (TGA), and isothermal gravimetric analysis (IGA). TGA revealed the outstanding thermal properties of P1 and P2 with 5% weight loss temperatures (T_d5) higher than 450°C. IGA proved their better thermal stability at 450°C for 800 min, compared to polydimethyldiphenylsiloxane. Dynamic mechanical analysis showed that silicone rubbers made from cyclodisilazane‐containing polydimethylsiloxanes could have a maximum tan δ value as high as 1.13 and had good prospects for damping material applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of polyimides with low viscosity and good thermal properties via copolymerization

Novel polyimides were successfully synthesized through copolymerization of diamine monomers p‐phenylenediamine (p‐PDA) and 4,4'‐diaminodiphenylmethane (MDA) with different proportions and 2,3,3',4'‐biphenyltetracarboxylic dianhydride (a‐BPDA) using 4‐phenylethynylphthalic anhydride (4‐PEPA) as an end‐capping agent. The melt rheological properties, thermal properties, and crystallinity of PI oligomers were investigated via rheometer, dynamic mechanical analysis (DMA), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), and X‐ray diffraction (XRD). The results indicate that melt viscosity and solubility of the PI oligomers were improved, but the glass transition temperature (T_g) and crystallinity decreased with the increasing molar ratio of MDA. PI oligomer 3 with the molar ratio of MDA/p‐PDA = 2/1 shows a lower minimum melt viscosity (66 Pa.s) at 313°C and better solubility in aprotic solvents. The corresponding PI‐3 exhibits a high glass transition temperature of 406°C and excellent thermal stability. This copolyimide shows good processability and thermal properties, and could become a good candidate of matrix resins for high performance composites in aerospace field. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41303.     

Synthesis and characterization of organo‐soluble fluorinated polyimides

A novel fluorinated diamine monomer with a keto group, 4‐[4‐amino‐2‐trifluoromethyl phenoxy]‐4′‐[4‐aminophenoxy]benzophenone (ATAB) was prepared by reacting dihydroxybenzophenone with 4‐chloronitrobenzene and 2‐chloro‐5‐nitrotrifluoromethylbenzene in the presence of potassium carbonate followed by catalytic reduction with palladized carbon (10%). Fluorinated polyimides IVa–e were synthesized from the diamine mentioned above via a two‐step method (thermal and chemical imidization). Polyimides IVa–e have inherent viscosities in the range 0.65–1.06 dL g^?1 (thermal imidization) and 0.82–1.56 dL g^?1 (chemical imidization). The polyimides prepared by chemical imidization exhibit excellent solubility. Polyimide films exhibit tensile strength, elongation and tensile modulus in the ranges 96–106 MPa, 9–13% and 1.1–1.7 GPa, respectively. The T₁₀ values of the polyimides are in the range 540–598 °C in nitrogen and 545–586 °C in air, with more than 50–60% char yield. They have T_g values between 244 and 285 °C. The prepared polyimides show cut‐off wavelengths in the range 365–412 nm and transmittance at 450 nm in the range 80.9–94.2%. The dielectric constants of the polyimide films are in the range 3.10–3.77 at 1 kHz and 3.04–3.66 at 10 kHz, with moisture absorption of 0.14–0.40%. Copyright © 2006 Society of Chemical Industry     

Synthesis and characterization of xanthan gum‐g‐N‐vinyl formamide with a potassium monopersulfate/Ag(I) system

A xanthan gum‐g‐N‐vinyl formamide graft copolymer was synthesized through the graft copolymerization of N‐vinyl formamide (NVF) onto xanthan gum with an efficient system, that is, potassium monopersulfate (PMS)/Ag(I) in an aqueous medium. The effects of the concentrations of Ag(I), PMS (KHSO₅), hydrogen ion, xanthan gum, and NVF along with the time and temperature on the graft copolymerization were studied by the determination of the grafting parameters (grafting ratio, add‐on, conversion, grafting efficiency, and homopolymer) and the rate of grafting. The maximum grafting ratio was obtained at a 0.6 g/dm³ concentration of xanthan gum. All the parameters showed an increasing trend with an increasing concentration of peroxymonosulfate, except the homopolymer percentage, which showed a decreasing trend. The grafting ratio, add‐on conversion, grafting efficiency, and rate of grafting increased with the concentration of Ag(I) increasing from 0.8 × 10^?2 to 1.2 × 10^?2 mol/dm³. The optimum time and temperature for the maximum degree of grafting were 90 min and 35°C, respectively. The graft copolymer was characterized with IR spectral analysis, thermogravimetric analysis, and differential calorimetry analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1637–1645, 2006     

Synthesis and characterization of heat‐resistant N‐phenylmaleimide–styrene–maleic anhydride copolymers and application in acrylonitrile–butadiene–styrene resin

The heat‐resistant copolymer of N‐phenylmaleimide (NPMI)–styrene (St)–maleic anhydride (MAH) was synthesized in xylene at 125°C with di‐tert‐butyl diperoxyterephthalate as an initiator. The characteristics of the copolymer were analyzed by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy (¹H‐NMR and ¹³C‐NMR), gel permeation chromatography, and elemental analysis. The ¹³C‐NMR results show that the copolymer possessed random sequence distribution; this was also supported by the differential scanning calorimetry experiment, in which a single glass‐transition temperature (T_g) of 202.3°C was observed. The thermal stability and degradation mechanism of the copolymer were investigated by thermogravimetric analysis. Using the Kissinger equation and Ozawa equation, we proved a nucleation controlling mechanism with an apparent activation energy of 144 kJ/mol. Blends of acrylonitrile–butadiene–styrene with the NPMI–St–MAH copolymer with various contents were prepared with a twin‐screw extruder processes. The mechanical and thermal properties of the materials, such as the tensile and flexural strength, T_g's, and Vicat softening temperatures, were all enhanced with the addition of the modifier, whereas the melt flow index decreased. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and properties of a second‐order,nonlinear‐optical,addition‐type polyimide with high thermal and temporal stability

A highly thermally and temporally stable, second‐order, nonlinear‐optical polyimide with an X‐type chromophore (2‐{4‐[4,5‐di(4‐nitrophenyl)imidazolyl]phenyl}‐4,5‐di(4‐aminophenyl)imidazole) was synthesized by the Michael addition reaction. The structure of the prepolymer was characterized with Fourier transform infrared (FTIR). Its thermal stability and curing behavior were studied with differential scanning calorimetry, thermogravimetric analysis, and FTIR. After the curing, the glass‐transition temperature of the polyimide greatly increased. The FTIR results suggested that addition and/or crosslinking reactions were carried out during the thermal curing of the prepolymer. A poling polyimide film was achieved, and the thermal and temporal stability of the poling‐induced orientation were evaluated with a multistep corona‐poling technique at an elevated temperature and with in situ second harmonic generation (SHG) measurements. The temporal orientation of the poled polyimide film was over 1000 h at 150°C; it retained 85% of the initial second‐order, nonlinear‐optical coefficient. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Low‐κ nanocomposite films based on polyimides with grafted polyhedral oligomeric silsesquioxane

Nanocomposites of polyimides (PI) with covalently grafted polyhedral oligomeric silsesquioxane (R₇R′Si₈O₁₂ or POSS) units were prepared by thermally‐initiated free‐radical graft polymerization of methacrylcyclopentyl‐POSS (MA‐POSS) with the ozone‐pretreated poly[N,N′‐(1,4‐phenylene)‐3,3′,4,4′‐benzophenonetetra‐carboxylic amic acid] (PAA), followed by thermal imidization. The chemical composition and structure of the PI with grafted methacrylcyclopentyl‐POSS side chains (PI‐g‐PMA‐POSS copolymers) were characterized by nuclear magnetic resonance (NMR), X‐ray diffraction (XRD), and thermogravimetric analysis (TGA). The POSS molecules in each grafted PMA side chain of the amorphous PI films retained the nanoporous crystalline structure, and formed an aggregate of crystallites. The PI‐g‐PMA‐POSS nanocomposite films had both lower and tunable dielectric constants, in comparison with that of the pristine PI films. Dielectric constants (κ's) of about 3.0–2.2 were obtained. The present approach offers a convenient way for preparing low‐κ materials based on existing PI's. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Poly(decamethylene terephthalamide) copolymerized with long‐chain alkyl dodecanedioic acid: Toward bio‐based polymer and improved performances

Poly(decamethylene terephthalamide) (PA10T), a bio‐based high‐performance semi‐aromatic polyamide, has been commercialized in recent years. However, there still are some weaknesses restricting its application range, such as narrow melt processing window and low ductility. In this study, we chose dodecanedioic acid (a potential bio‐based raw material) as the comonomer to prepare copolyamides [poly(decamethylene terephthalamide/decamethylene dodecanediamide), PA10T/1012] for solving these problems. The basic properties of these copolyamides were characterized by viscosity measurement, Fourier transform infrared spectrometer, proton nuclear magnetic resonance, wide‐angle X‐ray diffraction, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, and tensile measurement. Results show that, compared to PA10T, PA10T/1012 exhibits wider melt processing window and more outstanding elongation at break. Meanwhile, PA10T/1012 is still qualified for high temperature resistant material. Furthermore, T_g, T_d,5%, T_d,10%, and T_d,max of PA10T/1012 show a linear dependence on 1012 content, which is helpful to design new bio‐based copolyamides for meeting the needs of various occasions. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46531.     

Synthesis and characterization of amphiphilic PMTFPS‐b‐PEO diblock copolymers

A series of new amphiphilic poly[methyl(3,3,3‐trifluoropropyl) siloxane]‐b‐poly(ethyleneoxide) (PMTFPS‐b‐PEO) diblock copolymers with different ratio of hydrophobic segment to hydrophilic segment were prepared by coupling reactions of end‐functional PMTFPS and PEO homopolymers. PMTFPS‐b‐PEO diblock copolymers synthesized were shown to be well defined and narrow molecular weight distributed by characterizations such as NMR, GPC, and FTIR. Additionally, the solution properties of these diblock copolymers were investigated using tensiometry and transmission electron microscopy. Interestingly, the critical micellization concentration increases with increasing length of hydrophobic chain. Transmission electron microscopy studies showed that PMTFPS‐b‐PEO diblock copolymers in water preferentially aggregated into vesicles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Novel Poly(N‐isopropylacrylamide)‐graft‐poly(vinylidene fluoride) Copolymers for Temperature‐Sensitive Microfiltration Membranes

In the present work, we report on the synthesis and characterization of poly(vinylidene fluoride) (PVDF) with N‐isopropylacrylamide (NIPAAM) polymer side chains from molecular graft copolymerization in solution. The copolymer can be readily cast into temperature‐sensitive microfiltration (MF) membranes by the phase inversion technique. The copolymer approach to membrane fabrication allows a much better control of the physicochemical nature of the membrane pores through the variation in graft concentration, membrane casting temperature and concentration of the membrane casting solution.

     

Synthesis of Poly(methyl‐co‐trifluoropropyl)silsesquioxanes and Their Thin Films for Low Dielectric Application

Poly(methyl‐co‐trifluoropropyl)silsesquioxanes (P(M‐co‐TFP)SSQs) were prepared using methyltrimethoxysilane (MTMS) and trifluoropropyltrimethoxysilane (TFPTMS). The molecular weight, microstructure of the copolymers and properties of their thin films have been changed by adjusting reaction parameters such as the molar ratio of water to silane, the molar ratio of catalyst to silane, reaction time, solvent content, and temperature. The refractive index of the copolymer thin film decreased from 1.404 to ca. 1.348 as curing temperature was increased to 420 °C. The dielectric constant of the film decreased with an increase of the molecular weight of the copolymer, and the lowest dielectric constant obtained was ca. 2.2. Hardness and elastic modulus of the thin films were 0.7 and 5 GPa, respectively. Crack velocity was measured to be 10^?11 m/s at the film thickness of around 0.9 μm under aqueous environment.

     

Improving low‐density polyethylene/poly(ethylene terephthalate) blends with graft copolymers

Blends of low‐density polyethylene (LDPE) and poly(ethylene terephthalate) (PET) were prepared with different weight compositions with a plasticorder at 240°C at a rotor speed of 64 rpm for 10 min. The physicomechanical properties of the prepared blends were investigated with special reference to the effects of the blend ratio. Graft copolymers, that is, LDPE‐grafted acrylic acid and LDPE‐grafted acrylonitrile, were prepared with γ‐irradiation. The copolymers were melt‐mixed in various contents (i.e., 3, 5, 7, and 9 phr) with a LDPE/PET blend with a weight ratio of 75/25 and used as compatibilizers. The effect of the compatibilizer contents on the physicomechanical properties and equilibrium swelling of the binary blend was investigated. With an increase in the compatibilizer content up to 7 phr, the blend showed an improvement in the physicomechanical properties and reduced equilibrium swelling in comparison with the uncompatibilized one. The addition of a compatibilizer beyond 7 phr did not improve the blend properties any further. The efficiency of the compatibilizers (7 phr) was also evaluated by studies of the phase morphology (scanning electron microscopy) and thermal properties (differential scanning calorimetry and thermogravimetric analysis). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(imide-siloxane) films with controlled thickness

Polyimides containing siloxane moieties are used in some advanced applications. For example, these polymers can be employed as separation membranes in the form of self-standing, thin films. These products are formed by components of different polarities that have the tendency, at least partly, to separate in the final materials, with an impact on their final, bulk, and/or surface properties. The aim of this work is to study the dependence of the composition of the polyimide, poly(imide-siloxane) (PIS) and copolymeric PIS self-standing films differing in thickness on their properties. The important finding is that there is a rather large difference observed in the water contact angle on the film side oriented toward the air atmosphere during film preparation and that oriented toward a hydrophobic Teflon surface. Nevertheless, the gas transport properties of carbon dioxide and methane for these membranes are more influenced by the membrane composition than by the surface properties.     

Remendable polymers via reversible Diels–Alder cycloaddition of anthracene‐containing copolymers with fullerenes

Poly(lauryl methacrylate)s with anthracene moieties in the side chain were converted with C₆₀‐fullerene and phenyl‐C₆₁‐butyric acid methyl ester (PCBM), resulting in new remendable (self‐healing) polymeric materials. The utilization of differently substituted anthracene monomers enabled the tuning of the reactivity and the resulting mechanical properties. Copolymers with different contents of the anthracene moieties were synthesized and characterized using size exclusion chromatography, ¹H nuclear magnetic resonance (NMR) spectroscopy as well as differential scanning calorimetry (DSC). ¹H NMR spectroscopic studies were utilized in order to investigate the reversibility of the Diels–Alder reaction between copolymers with C₆₀‐fullerene and PCBM, respectively, in solution. In order to investigate the conversion of the polymers with C₆₀‐fullerene and PCBM in bulk, additionally, DSC, nanoindentation, rheology, atomic force microscopy (AFM), 3D microscopy, simultaneous thermal analysis (STA) and FT‐Raman investigations were performed. The fullerene‐containing copolymers could be healed in a temperature range of 40–80 °C. Consequently, a new generation of low temperature remendable polymers could be established. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45916.