Experimental results and fatigue life evaluation of magnesium laserbeam‐welded joints under proportional and non‐proportional multiaxial fatigue loading with variable amplitudes

Fatigue life of magnesium laserbeam‐welds (AZ31 and AZ61 alloys) was assessed experimentally under variable amplitude loadings. The specimens were subjected to load‐controlled cyclic loadings. The tests were carried out using a Gauss‐distributed amplitude sequence of length L_S = 5 · 10⁴ cycles and loading ratio R = –1 under pure axial, pure torsion as well as in‐phase and out‐of‐phase combined loadings. The notch stresses were obtained from a linear‐elastic FE‐model using the reference radius approach with r_ref  = 0.05 mm. The stress‐based hypotheses were applied: Effective equivalent stress hypothesis (EESH), shear stress intensity hypothesis (SIH), Findley, and modified Gough‐Pollard. A non‐proportionality factor is introduced and steps required for computing are presented in order to improve fatigue life assessment under non‐proportional loadings.     

Multiaxial low‐cycle fatigue life evaluation under different non‐proportional loading paths

This paper presents analytical and experimental investigations for fatigue lives of structures under uniaxial, torsional, multiaxial proportional, and non‐proportional loading conditions. It is known that the rotation of principal stress/strain axes and material additional hardening due to non‐proportionality of cycle loading are the 2 main causes resulting in shorter fatigue lives compared with those under proportional loading. This paper treats these 2 causes as independent factors influencing multiaxial fatigue damage and proposes a new non‐proportional influencing parameter to consider their combined effects on the fatigue lives of structures. A critical plane model for multiaxial fatigue lives prediction is also proposed by using the proposed non‐proportional influencing factor to modify the Fatemi‐Socie model. The comparison between experiment results and theoretical evaluation shows that the proposed model can effectively predict the fatigue life due to multiaxial non‐proportional loading.     

Multiaxial notch fatigue life prediction based on pseudo stress correction and finite element analysis under variable amplitude loading

A new computational methodology is proposed for fatigue life prediction of notched components subjected to variable amplitude multiaxial loading. In the proposed methodology, an estimation method of non‐proportionality factor (F) proposed by authors in the case of constant amplitude multiaxial loading is extended and applied to variable amplitude multiaxial loading by using Wang‐Brown's reversal counting approach. The pseudo stress correction method integrated with linear elastic finite element analysis is utilized to calculate the local elastic‐plastic stress and strain responses at the notch root. For whole local strain history, the plane with weight‐averaged maximum shear strain range is defined as the critical plane in this study. Based on the defined critical plane, a multiaxial fatigue damage model combined with Miner's linear cumulative damage law is used to predict fatigue life. The experimentally obtained fatigue data for 7050‐T7451 aluminium alloy notched shaft specimens under constant and variable amplitude multiaxial loadings are used to verify the proposed methodology and equivalent strain‐based methodology. The results show that the proposed methodology is superior to equivalent strain‐based methodology.     

A critical plane‐energy model for multiaxial fatigue life prediction

A new critical plane‐energy model is proposed in this paper for multiaxial fatigue life prediction of metals. A brief review of existing methods, especially on the critical plane‐based and energy‐based methods, is given first. Special focus is on the Liu–Mahadevan critical plane approach, which has been shown to work for both brittle and ductile metals. One potential drawback of the Liu–Mahadevan model is that it needs an empirical calibration parameter for non‐proportional multiaxial loadings because only the strain terms are used and the out‐of‐phase hardening cannot be explicitly considered. An energy‐based model using the Liu–Mahadevan concept is proposed with the help of the Mróz–Garud plasticity model. Thus, the empirical calibration for non‐proportional loading is not needed because the out‐of‐phase hardening is naturally included in the stress calculation. The model predictions are compared with experimental data from open literature, and the proposed model is shown to work for both proportional and non‐proportional multiaxial loadings without the empirical calibration.     

The multiaxial weld root fatigue of butt welded joints subjected to uniaxial loading

In this study, the fatigue strength of inclined butt welds subjected to a proportional multiaxial stress state generated by uniaxial loading is studied in nominal and local stress concepts. The local methodologies studied included principal stress hypothesis, von Mises stress hypothesis and modified Wöhler curve method. Nominal methodologies included modified Gough–Pollard interaction equation, the design equation in Eurocode3 and the interaction equation in DNV standard. Results are evaluated along with data published in relevant literature. It is observed that both local and nominal stress assessment methods are able to estimate multiaxial fatigue strength. No obvious difference in fatigue strength is observed in the nominal stress concept, but the notch stress concept is able to capture a decrease in fatigue strength in shear‐dominated joints. It is concluded that modified Wöhler curve method is a suitable tool for the evaluation of fatigue strength in joints dominated by both normal and shear stresses.     

On the estimation of the material fatigue properties required to perform the multiaxial fatigue assessment

To accurately perform the fatigue assessment of engineering components subjected to in‐service multiaxial fatigue loading, the adopted design criterion must properly be calibrated, the used information usually being the fatigue strength under both pure uniaxial and pure torsional fatigue loading. Because of the complex fatigue response of metallic materials to multiaxial loading paths, the only reliable way to generate the necessary pieces of calibration information is by running appropriate experiments. Unfortunately, because of a lack of both time and resources, very often, structural engineers are requested to perform the multiaxial fatigue assessment by guessing the necessary fatigue properties. In this complex scenario, initially, the available empirical rules suitable for estimating fatigue strength under both pure axial and pure torsional fatigue loading are reviewed in detail. Subsequently, several experimental results taken from the literature and generated by testing metallic materials under a variety of proportional and non‐proportional multiaxial loading paths are used to investigate the way such empirical rules affect the accuracy in estimating fatigue strength, the damage extent being evaluated according to the modified Wöhler curve method. Such a systematic validation exercise allowed us to prove that under proportional loading (with both zero and non‐zero mean stresses), an adequate margin of safety can be reached even when the necessary calibration information is directly estimated from the material ultimate tensile strength. On the contrary, in the presence of non‐proportional loading, the use of the empirical rules reviewed in the present paper can result, under particular circumstances, in a non‐conservative fatigue design.     

Multiaxial notch fatigue life prediction based on the dominated loading control mode under variable amplitude loading

A new calculation approach is suggested to the fatigue life evaluation of notched specimens under multiaxial variable amplitude loading. Within this suggested approach, if the computed uniaxial fatigue damage by the pure torsional loading path is larger than that by the axial tension–compression loading path, a shear strain‐based multiaxial fatigue damage parameter is assigned to calculate multiaxial fatigue damage; otherwise, an axial strain‐based multiaxial fatigue damage parameter is assigned to calculate multiaxial fatigue damage. Furthermore, the presented method employs shear strain‐based and axial strain‐based multiaxial fatigue damage parameters in substitution of equivalent strain amplitude to consider the influence of nonproportional additional hardening. The experimental data of GH4169 superalloy and 7050‐T7451 aluminium alloy notched components are used to illustrate the presented multiaxial fatigue lifetime estimation approach for notched components, and the results reveal that estimations are accurate.     

Lebensdauer von Schweißverbindungen unter mehrachsigen Belastungen mit variablen Amplituden – Schadensakkumulation und Hypothese der wirksamen Vergleichsspannung

Fatigue Life of Welded Joints under Multiaxial Variable Amplitude Loading – Damage Accumulation and the Effective Equivalent Stress Hypothesis Flange‐tube joints from fine grained steel FeE 460 with different notch factors were investigated under biaxial constant and Gaussian variable amplitude loading (bending and torsion) in the range of 10⁴ to 5 · 10⁶ cycles to crack initiation and break‐through, respectively. In order not to interfere with residual stresses they were stress relieved by a heat treatment. Damage accumulation under a Gaussian spectrum can be assessed for in‐ and out of phase combined bending and torsion using an allowable damage sum of 0.35 for weldments in the as‐welded state and 0.16 for joints with machined weldments with a lower notch factor of the critical area. For the evaluation of multiaxial in‐ and out‐of‐phase stresses the introduced hypothesis of the effective equivalent stress leads to good results. For this, the knowledge of local strains or stresses is necessary. This hypothesis considers the fatigue‐life reducing influence of out‐of‐phase loading by taking into account the interaction of local shear stresses acting in different surface planes of the material. Further, size effects resulting from the weld geometry and loading mode were included.     

Corrosion fatigue behaviour of 304 stainless steel under proportional and non‐proportional multiaxial loading condition

Corrosion fatigue and electrochemical tests under proportional loading and non‐proportional loading were conducted on 304 stainless steel in 0.63 mol L^?1 NaCl solution at room temperature. Two biaxial loading paths were applied to study the effect of proportional loading and non‐proportional loading on corrosion fatigue behaviour. Surface and fractographic observations of multiaxial corrosion fatigue specimens were carried out by scanning electron microscopy. It was shown that proportional loading had a more significant effect on the occurrence of local corrosion compared with non‐proportional loading because the continuous rotation of the principal stress plane under non‐proportional loading inhibits the pit formation.     

Fatigue design of welded double‐sided T‐joints and double‐sided cruciform joints in steel marine structures: A total stress concept

Fatigue is a governing design limit state for marine structures. Welded joints are important in that respect. The weld notch stress (intensity) distributions contain essential information and formulations have been established to obtain a total stress fatigue damage criterion and corresponding fatigue resistance curve; a total stress concept. However, the involved weld load carrying stress model does not provide the required estimates and trends for varying geometry dimensions and loading & response combinations. A new one has been developed and performance evaluation for T‐joints and cruciform joints in steel marine structures shows that in comparison with the nominal stress, hot spot structural stress and effective notch stress concept based results up to 50% more accurate fatigue design life time estimates can be obtained. Taking advantage of the weld notch stress formulations, the effective notch stress concept performance has improved adopting a stress‐averaged criterion rather than a fictitious notch radius‐based one.     

Prediction methods of fatigue critical point for notched components under multiaxial fatigue loading

Two methods based on local stress responses are proposed to locate fatigue critical point of metallic notched components under non‐proportional loading. The points on the notch edge maintain a state of uniaxial stress even when the far‐field fatigue loading is multiaxial. The point bearing the maximum stress amplitude is recognized as fatigue critical point under the condition of non‐mean stress; otherwise, the Goodman's empirical formula is adopted to amend mean stress effect prior to the determination of fatigue critical point. Furthermore, the uniaxial stress state can be treated as a special multiaxial stress state. The Susmel's fatigue damage parameter is employed to evaluate the fatigue damage of these points on the notch edge. Multiaxial fatigue tests on thin‐walled round tube notched specimens made of GH4169 nickel‐base alloy and 2297 aluminium‐lithium alloy are carried out to verify the two methods. The prediction results show that both the stress amplitude method and the Susmel's parameter method can accurately locate the fatigue critical point of metallic notched components under multiaxial fatigue loading.     

Non-proportional multiaxial whole-life transformation ratchetting and fatigue failure of super-elastic NiTi shape memory alloy micro-tubes

Experimental observations are performed to investigate the non-proportional multiaxial whole-life transformation ratchetting and fatigue failure of superelastic NiTi SMA micro-tubes in stress-controlled loadings at human-body temperature (310 K). The effects of axial mean stress and stress hold on the whole-life transformation ratchetting and fatigue life are investigated with uniaxial, torsional and five different multiaxial loading paths. The results show that the stress holds on the upper or lower transformation plateaus will both promote forward and reverse transformation, and lead to shorter fatigue life. The multiaxial fatigue lives of NiTi shape memory alloy depend significantly on loading paths and applied stress levels.     

Notch fatigue life prediction considering nonproportionality of local loading path under multiaxial cyclic loading

An innovative numerical methodology is presented for fatigue lifetime estimation of notched bodies experiencing multiaxial cyclic loadings. In the presented methodology, an evaluation approach of the local nonproportionality factor F for notched specimens, which defines F as the ratio of the pseudoshear strain range at 45° to the maximum shear plane and the maximum shear strain range, is proposed and discussed deeply. The proposed evaluation method is incorporated into the material cyclic stress‐strain equation for purpose of describing the nonproportional hardening behavior for some material. The comparison between multiaxial elastic‐plastic finite element analysis (FEA) and experimentally measured strains for S460N steel notched specimens shows that the proposed nonproportionality factor estimation method is effective. Subsequently, the notch stresses and strains calculated utilizing multiaxial elastic‐plastic FEA are used as input data to the critical plane‐based fatigue life prediction methodology. The prediction results are satisfactory for the 7050‐T7451 aluminum alloy and GH4169 superalloy notched specimens under multiaxial cyclic loading.     

State‐of‐the‐art review on the local strain energy density concept and its relation to the J‐integral and peak stress method

The local average strain energy density (SED) approach has been proposed and elaborated by Lazzarin for strength assessments in respect of brittle fracture and high‐cycle fatigue. Pointed and rounded (blunt) V‐notches subjected to tensile loading (mode 1) are primarily considered. The method is systematically extended to multiaxial conditions (mode 3, mixed modes 1 and 2). The application to brittle fracture is documented for PMMA flat bar specimens with pointed or rounded V‐notches inclusive of U‐notches. Results for other brittle materials (ceramics, PVC, duraluminum and graphite) are also recorded. The application to high‐cycle fatigue comprises fillet‐welded joints, weld‐like shaped and V‐notched base material specimens as well as round bar specimens with a V‐notch. The relation of the local SED concept to comparable other concepts is investigated, among them the Kitagawa, Taylor and Atzori–Lazzarin diagrams, the Neuber concept of fictitious notch rounding applied to welded joints and also the J‐integral approach. Alternative details of the local SED concept such as a semicircular control volume, microrounded notches and slit‐parallel loading are also mentioned. Coarse FE meshes at pointed or rounded notch tips are proven to be acceptable for accurate local SED evaluations. The peak stress method proposed by Meneghetti, which is based on a notch stress intensity factor consideration combined with a globally even coarse FE mesh and is used for the assessment of the fatigue strength of welded joints, is also presented.     

A novel accumulative fatigue damage model for multiaxial step spectrum considering the variations of loading amplitude and loading path

In this paper, based on the process of the fatigue crack initiation and the critical plane theory, a continuous stress parameter was proposed to quantify the driving force of the fatigue crack initiation for the fully reversed multiaxial fatigue loading. In this stress parameter, the shear stress amplitude and normal stress amplitude on the critical plane were combined with the variable coefficients which were affected by the normalized fatigue life and the loading non‐proportionality. Owing to these coefficients, for the multiaxial loadings with different non‐proportionalities, the driving force of the fatigue crack initiation during the whole life could be described. After that, a novel accumulative fatigue damage model was established for the multiaxial two‐stage step spectrum. In this model, the accumulative damage was calculated according to the variation of the proposed stress parameter on the critical plane. Considering the directionality of the multiaxial fatigue damage, for the spectrum in which the loading path was variable, the damage accumulation was carried out on the critical planes of the both loadings, and the larger one was chosen as the final accumulative fatigue damage. In order to verify the new model, up to 41 different multiaxial two‐stage step spectrum loading tests on 2024‐T4 aluminium alloy were collected. The new model, as well as other five commonly used models, was applied to calculate the accumulative fatigue damage. The final results showed that, compared with other commonly used models, the new model had the most accurate results with the smallest scatters.     

Short crack approach for multiaxial fatigue assessment

A significant part of the fatigue life is spent during short crack growth. Therefore, modelling of short fatigue crack growth offers an opportunity to improve the accuracy of numerical life assessment. Besides stating some general remarks on the short crack approach itself and on multiaxial fatigue criteria, a short crack growth based fatigue life prediction approach for multiaxial non‐proportional loading is presented. This approach accounts for the geometrical size effect by considering the geometry correction functions for semi‐elliptical surface cracks in inhomogeneous gradient stress fields. The geometrical size effect is becoming significant for notch radii smaller than four times the defined technical crack size. Additionally, life influencing factors due to the statistical size effect have been taken into account. The comparison of calculated and experimentally observed fatigue lives of shouldered shafts made of S460N with notch radii of 0.2 to 4.0 mm under non‐proportional tension and torsion loading yields a satisfying accuracy.     

Proportional/nonproportional constant/variable amplitude multiaxial notch fatigue: cyclic plasticity,non‐zero mean stresses,and critical distance/plane

This paper deals with the formulation and experimental validation of a novel fatigue lifetime estimation technique suitable for assessing the extent of damage in notched metallic materials subjected to in‐service proportional/nonproportional constant/variable amplitude multiaxial load histories. The methodology being formulated makes use of the Modified Manson‐Coffin Curve Method, the Shear Strain–Maximum Variance Method, and the elasto‐plastic Theory of Critical Distances, with the latter theory being applied in the form of the Point Method. The accuracy and reliability of our novel fatigue lifetime estimation technique were checked against a large number of experimental results we generated by testing, under proportional/nonproportional constant/variable amplitude axial‐torsional loading, V‐notched cylindrical specimens made of unalloyed medium‐carbon steel En8 (080M40). Specific experimental trials were run to investigate also the effect of non‐zero mean stresses as well as of different frequencies between the axial and torsional stress/strain components. This systematic validation exercise allowed us to demonstrate that our novel multiaxial fatigue assessment methodology is remarkably accurate, with the estimates falling within an error factor of 2. By modelling the cyclic elasto‐plastic behaviour of metals explicitly, the design methodology being formulated and validated in the present paper offers a complete solution to the problem of estimating multiaxial fatigue lifetime of notched metallic materials, with this holding true independently of sharpness of the stress/strain raiser and complexity of the load history.     

Low‐cycle fatigue/high‐cycle fatigue interactions in notched Ti‐6Al‐4V*

Combined low‐cycle fatigue/high‐cycle fatigue (LCF/HCF) loadings were investigated for smooth and circumferentially V‐notched cylindrical Ti–6Al–4V fatigue specimens. Smooth specimens were first cycled under LCF loading conditions for a fraction of the previously established fatigue life. The HCF 10⁷ cycle fatigue limit stress after LCF cycling was established using a step loading technique. Specimens with two notch sizes, both having elastic stress concentration factors of K_t = 2.7, were cycled under LCF loading conditions at a nominal stress ratio of R = 0.1. The subsequent 10⁶ cycle HCF fatigue limit stress at both R = 0.1 and 0.8 was determined. The combined loading LCF/HCF fatigue limit stresses for all specimens were compared to the baseline HCF fatigue limit stresses. After LCF cycling and prior to HCF cycling, the notched specimens were heat tinted, and final fracture surfaces examined for cracks formed during the initial LCF loading. Fatigue test results indicate that the LCF loading, applied for 75% of total LCF life for the smooth specimens and 25% for the notched specimens, resulted in only small reductions in the subsequent HCF fatigue limit stress. Under certain loading conditions, plasticity‐induced stress redistribution at the notch root during LCF cycling appears responsible for an observed increase in HCF fatigue limit stress, in terms of net section stress.     

Low cycle fatigue life of Ti–6Al–4V alloy under non-proportional loading

Multiaxial low cycle fatigue life of Ti–6Al–4V under non-proportional loading was studied. Strain-controlled multiaxial fatigue tests at room temperature were carried out using tubular specimens. The strain paths employed were push–pull loading, reversed torsion loading, and two kinds of 90° out-of-phase loadings. The former two loadings are proportional loading tests where the principal directions of stress and strain are fixed in the cycle. The latter two are non-proportional loading tests where there is a 90° phase difference between axial and shear loadings, and the principal directions are cyclically rotated continuously. Failure lives are reduced obviously by non-proportional loadings in comparison with those in proportional loading tests. This paper focuses on determining a suitable fatigue model for evaluating the failure lives of Ti–6Al–4V under multiaxial loading.