Morphology and mechanical properties of polypropylene/high‐impact polystyrene blends from postconsumer plastic waste

The compatibilizing effect of the triblock copolymer poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS) on the morphological and mechanical properties of virgin and recycled polypropylene (PP)/high‐impact polystyrene (HIPS) blends was studied, with the properties optimized for rigid composite films. The components of the blend were obtained from municipal plastic waste, PP being acquired from mineral water bottles (PP_b) and HIPS from disposable cups. These materials were preground, washed only with water, dried with hot air, and ground again (PP_b) or agglutinated (HIPS). Blends with three different weight ratios of PP_b and HIPS (6:1, 6:2, and 6:3) were prepared, and three different concentrations of SEBS (5, 6, and 7 wt %) were used for investigations of its compatibilizing effect. Scanning electron microscopy showed that SEBS reduced the diameter of dispersed HIPS particles in the globular and fibril shapes and improved the adhesion between the disperse phase and the matrix. However, SEBS interactions with PP_b and HIPS influenced the mechanical properties of the compatibilized PP_b/HIPS/SEBS blends. An adequate composition of PP/HIPS, for both virgin and recycled blends, for applications in composite films with characteristics similar to those of synthetic paper was obtained with a minimal amount of SEBS and a maximal HIPS/PP ratio in the range of concentrations studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2861–2867, 2003     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Mechanical properties of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Mechanical properties of isotactic polypropylene/wollastonite/styrene rubber block copolymers (iPP/wollastonite/SRBC) composites were studied as a function of elastomeric poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and SEBS grafted with maleic anhydride (SEBS‐g‐MA) content from 0 to 20 vol%. Microphase morphology was stronger influenced by SRBC elastomers than by different wollastonite types. Higher encapsulation ability of SEBS‐g‐MA than SEBS caused more expressive core‐shell morphology and consequently higher notched impact strength as well as yield parameters, but lower Young's modulus. Higher ductility of the composites with SEBS than with SEBS‐g‐MA has been primarily caused by better miscibility of the polypropylene chains with SEBS molecules. Surface properties of components and adhesion parameters also indicated that adhesion at SEBS‐g‐MA/wollastonite interface, which was stronger than the one at the SEBS/wollastonite interface, influenced higher encapsulation of wollastonite particles by SEBS‐g‐MA. POLYM. ENG. SCI., 47:1873–1880, 2007. © 2007 Society of Plastics Engineers     

Synthesis of polydimethylsiloxane‐block‐polystyrene‐block‐polydimethylsiloxane via polysiloxane‐based macroinitiator in supercritical CO2

Polydimethylsiloxane‐block‐polystyrene‐block‐polydimethylsiloxane (PDMS‐b‐PS‐b‐PDMS) was synthesized by the radical polymerization of styrene using a polydimethylsiloxane‐based macroazoinitiator (PDMS MAI) in supercritical CO₂. PDMS MAI was synthesized by reacting hydroxy‐terminated PDMS and 4,4′‐azobis(4‐cyanopentanoyl chloride) (ACPC) having a thermodegradable azo‐linkage at room temperature. The polymerization of styrene initiated by PDMS MAI was investigated in a batch system using supercritical CO₂ as the reaction medium. PDMS MAI was found to behave as a polyazoinitiator for radical block copolymerization of styrene, but not as a surfactant. The response surface methodology was used to design the experiments. The parameters used were pressure, temperature, PDMS MAI concentration and reaction time. These parameters were investigated at three levels (?1, 0 and 1). The dependent variable was taken as the polymerization yield of styrene. PDMS MAI and PDMS‐b‐PS‐b‐PDMS copolymers obtained were characterized by proton nuclear magnetic resonance and infrared spectroscopy. The number‐ and weight‐average molecular weights of block copolymers were determined by gel permeation chromatography. Copyright © 2004 Society of Chemical Industry     

Polypropylene/styrene‐ethylene‐butylene‐styrene thermoplastic elastomer nanocomposite films

Nanocomposite (polypropylene/styrene‐ethylene‐butylene‐styrene/organoclay) films were sheet‐extruded with differing clay concentrations. Blends were compounded using a high shear single screw reciprocating kneader. Results demonstrated that higher clay content increased the Shore A hardness of the films but induced a significant improvement in both O₂ and CO₂ barrier performance. J. VINYL ADDIT. TECHNOL., 13:46–52, 2007. © 2007 Society of Plastics Engineers.     

Compatibilization effects of styrenic/rubber block copolymers in polypropylene/polystyrene blends

Compatibilizing effects of styrene/rubber block copolymers poly(styrene‐b‐butadiene‐b‐styrene) (SBS), poly(styrene‐b‐ethylene‐co‐propylene) (SEP), and two types of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS), which differ in their molecular weights on morphology and selected mechanical properties of immiscible polypropylene/polystyrene (PP/PS) 70/30 blend were investigated. Three different concentrations of styrene/rubber block copolymers were used (2.5, 5, and 10 wt %). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the phase morphology of blends. The SEM analysis revealed that the size of the dispersed particles decreases as the content of the compatibilizer increases. Reduction of the dispersed particles sizes of blends compatibilized with SEP, SBS, and low‐molecular weight SEBS agrees well with the theoretical predictions based on interaction energy densities determined by the binary interaction model of Paul and Barlow. The SEM analysis confirmed improved interfacial adhesion between matrix and dispersed phase. The TEM micrographs showed that SBS, SEP, and low‐molecular weight SEBS enveloped and joined pure PS particles into complex dispersed aggregates. Bimodal particle size distribution was observed in the case of SEP and low‐molecular weight SEBS addition. Notched impact strength (a_k), elongation at yield (ε_y), and Young's modulus (E) were measured as a function of weight percent of different types of styrene/rubber block copolymers. The a_k and ε_y were improved whereas E gradually decreased with increasing amount of the compatibilizer. The a_k was improved significantly by the addition of SEP. It was found that the compatibilizing efficiency of block copolymer used is strongly dependent on the chemical structure of rubber block, molecular weight of block copolymer molecule, and its concentration. The SEP diblock copolymer proved to be a superior compatibilizer over SBS and SEBS triblock copolymers. Low‐molecular weight SEBS appeared to be a more efficient compatibilizer in PP/PS blend than high‐molecular weight SEBS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 291–307, 1999     

Phase structure and morphology of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Supermolecular structure of isotactic polypropylene/wollastonite/styrenic rubber block copolymers composites were studied as a function of elastomeric poly‐ (styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and the SEBS grafted with maleic anhydride (SEBS‐g‐MA) content (from 0 to 20 vol%) by optical, scanning, and transmission electron microscopy, wide‐angle X‐ray diffraction and differential scanning calorimetry. Wollastonite particles disturbed the spherulitization of polypropylene matrix. Both elastomers affected the crystallization of polypropylene matrix mainly by solidification effect. Although SEBS‐g‐MA encapsulated wollastonite particles more expressive than SEBS forming thus core‐shell morphology in higher extent, scanning electron micrographs indicated more constrained wollastonite particles in fractured surfaces of composites with SEBS elastomer. Moreover, SEBS‐g‐MA disorientated wollastonite particles and affected reorientation of the polypropylene crystallites stronger than SEBS elastomer. POLYM. ENG. SCI., 47:2145–2154, 2007. © 2007 Society of Plastics Engineers     

Mechanical properties of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Mechanical properties of the isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, the poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. An increase in toughness of iPP with the elastomers was associated with a decrease in rigidity and strength. Mechanical performance of iPP increased more with acicular W than with spherical GB due to reinforcing effect of W. Comparing the (iPP/GB)/SEBS and (iPP/W)/SEBS composites having the separate microstructure, strength and toughness values of the iPP/GB and iPP/W composites increased more with SEBS‐g‐MA at the expense of rigidity due to the core‐shell microstructure with strong interfacial adhesion. Moreover, the iPP/W composite exhibited superior mechanical performance with 2.5 and 5 vol% of SEBS‐g‐MA because of a positive synergy between the core‐shell microstructure and reinforcing effect of acicular W. The extended models revealed that the elastomer and filler particles in the (iPP/GB)/SEBS and (iPP/W)/SEBS composites acted individually due to the separate microstructure. However, the rigid GB and W particles encapsulated with the thick elastomer interlayer (R₀/R₁ = 0.91) in the (iPP/GB)/SEBS‐g‐MA and (iPP/W)/SEBS‐g‐MA composites acted like neither big elastomer particles nor like individual rigid particles, inferring more complicated failure mechanisms in the core‐shell composites. POLYM. COMPOS., 31:1285–1308, 2010. © 2010 Society of Plastics Engineers     

Reactive mixing of PET and PET/PP blends with glycidyl methacrylate–modified styrene‐b‐(ethylene‐co‐olefin) block copolymers

Styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene (SEBS) and styrene‐b‐(ethylene‐co‐propylene) (SEP, SEPSEP) block copolymers with different styrene contents and different numbers of blocks in the copolymer chain were functionalized by melt radical grafting with glycidyl methacrylate (GMA) and employed as compatibilizers for PET‐based blends. Binary blends of PET with both functionalized (SEBS‐g‐GMA, SEP‐g‐GMA, SEPSEP‐g‐GMA) and neat (SEBS, SEP, SEPSEP) copolymers (75 : 25 w/w) and ternary blends of PET and PP (75 : 25 w/w) with various amounts (2.5–10 phr) of both modified and unmodified copolymers were prepared in an internal mixer, and their properties were evaluated by SEM, DSC, melt viscosimetry, and tensile and impact tests. The roles of the chemical structure, grafting degree, and concentration of the various copolymers on blend compatibilization was investigated. The blends with the grafted copolymers showed a neat improvement of phase dispersion and interfacial adhesion compared to the blends with nonfunctionalized copolymers. The addition of grafted copolymers resulted in a marked increase in melt viscosity, which was accounted for by the occurrence of chemical reactions between the epoxide groups of GMA and the carboxyl/hydroxyl end groups of PET during melt mixing. Blends with SEPSEP‐g‐GMA and SEBS‐g‐GMA, at concentrations of 5–10 phr, showed a higher compatibilizing effect with enhanced elongation at break and impact resistance. The effectiveness of GMA‐functionalized SEBS was then compared to that of maleic anhydride–grafted SEBS. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2201–2211, 2005     

Characterization of morphology in chemically modified styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene by solid‐state nuclear magnetic resonance

Multiphase triblock styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene (SEBS) copolymers chemically modified with maleic anhydride (MAH) in the presence of a radical initiator by reactive extrusion were studied by solid‐state ¹H‐NMR and ¹³C‐NMR. In the experiments performed, the concentrations of MAH and initiator were kept constant, whereas the temperature profile in the extruder was varied. Samples with known extents of grafting and crosslinking were analyzed with NMR with techniques based on proton spin diffusion to investigate the microphase structure of the modified copolymers. The ¹³C‐NMR results show that the size of the rigid domains was about 15 nm and was not significantly changed by the modification. Alterations in the rubbery phase were illustrated by measured changes in proton spin‐spin (T₂) relaxation times. The fraction of protons having intermediate mobilities increased slightly in modified SEBS with respect to that observed in unmodified copolymers. These results were found to be independent of the extruder temperature profiles used, at least in the range studied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐ b‐styrene] on dielectric,thermal, and morphological characteristics of polypropylene/silica nanocomposites

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) copolymer on the thermal and dielectric properties of polypropylene (PP)—nanosilica (NS) composites in relation with morphological aspects revealed by atomic force microscopy (AFM) was investigated in this article. SEBS hindered the crystallization process of PP in PP/NS composites, leading to a smaller degree of crystallinity and lower perfection of crystalline structure. Broader lamellar thickness distribution was obtained in nanocomposites containing SEBS. Almost two times higher dielectric loss as compared to PP reference and two relaxation processes were detected in ε_r ^′′(f) curves of nanocomposites. The first peak, in the same frequency domain as for the references, was assigned to α‐relaxation of polymer components together with interfacial polarization. The relaxation time follows the Arrhenius law with an activation energy of 80–90 kJ/mol. For the second process, the temperature dependence of the relaxation times obeyed the VFT equation. The dielectric changes following the incorporation of SEBS support its tendency to hinder the motional processes in PP, in accordance with DSC results. A smooth transition from a phase rich in SEBS to one containing mainly PP was detected in the AFM image of the composite with the larger amount of SEBS, emphasizing the good compatibility at the PP/SEBS interface. POLYM. ENG. SCI., 53:2081–2092, 2013. © 2013 Society of Plastics Engineers     

Investigation on the morphological and mechanical properties of (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) ternary blends

In this work, ternary polymer blends based on (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) (SEBS) triblock copolymer and a varying concentration of the reactive (maleic anhydride)‐grafted SEBS were prepared by using a melt‐blending process. The effects of the material parameters (composition of ternary blends and SEBS/[{maleic anhydride}‐grafted SEBS] concentration ratio) and blending sequence on the morphological and mechanical properties of ternary blends were studied. Taguchi experimental design methodology was employed to design the experiments and select the material and processing parameters for the optimized mechanical properties. Tensile properties (Young's modulus and yield stress) and impact strength were considered as the response variables. It was demonstrated that there is a meaningful relationship between the composition of blends, processing parameters, observed phase structure, and obtained mechanical properties. The mechanical tests showed that the highest impact strength was achieved as the dispersion of the rubbery phase achieved an optimum size of about 1 μm. J. VINYL ADDIT. TECHNOL., 23:329–337, 2017. © 2015 Society of Plastics Engineers     

Tailored dielectric and mechanical properties of noncovalently functionalized carbon nanotube/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) nanocomposites

The preparation of high‐dielectric poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) composites containing functionalized single‐walled carbon nanotubes (f‐SWCNTs) noncovalently appended with dibutyltindilaurate are reported herein. Transmission electron microscopy and X‐ray photoelectron and Raman spectroscopy confirmed the noncovalent functionalization of the SWCNTs. The SEBS‐f‐SWCNT composites exhibited enhanced mechanical properties as well as a stable and high dielectric constant of approximately 1000 at 1 Hz with rather low dielectric loss at 2 wt% filler content. The significantly enhanced dielectric property originates from the noncovalent functionalization of the SWCNTs that ensures good dispersion of the f‐SWCNTs in the polymer matrix. The f‐SWCNTs also acted as a reinforcing filler, thereby enhancing the mechanical properties of the composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Studies on morphology and mechanical properties of PP/HIPS blends from postconsumer plastic waste

The aim of this work was to study the compatibilizing effect of the triblock copolymer poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS) on the morphology and mechanical properties of virgin and recycled polypropylene/high‐impact polystyrene (PP/HIPS) blends. The components of the blend were obtained from municipal plastics waste (MPW), with the PP obtained from blue mineral water bottles, symbolized as PP_b, and the HIPS from disposable cups. These materials were preground, washed only with water, dried with hot air, and ground again (PP_b) or agglutinated (HIPS). Blends of PP_b and HIPS in three weight ratios (6:1, 6:2, and 6:3) were prepared, and three concentrations of SEBS (5.0, 6.0, and 6.7% w/w) were used for investigations of its compatibilizing effect. Scanning electron microscopy (SEM) showed that SEBS reduced the diameter of HIPS dispersed particles that were globular and fibril shaped, along with improving the adhesion between the dispersed phase and the matrix. On the other hand, SEBS interactions with PP_b and HIPS influenced the mechanical properties of the compatibilized PP_b/HIPS/SEBS blends. The optimal concentration of SEBS was 5 wt % for application to composite films with similar characteristics to synthetic paper. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 747–751, 2003     

Polypropylene/silica micro‐ and nanocomposites modified with poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene)

The effects of different silica loadings and elastomeric content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with 5, 10, 15, and 20 vol % of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) SEBS added to total composite volume were investigated. Four silica fillers differing in size (nano‐ vs. micro‐) and in surface properties (untreated vs. treated) were chosen as fillers. Elastomer SEBS was added as impact modifier and compatibilizer at the same time. The morphology of ternary polymer composites revealed by light and scanning electron microscopies was compared with morphology predicted models based on interfacial properties. The results indicated that general morphology of composite systems was determined primarily by interfacial properties, whereas the spherulitic morphology of polypropylene matrix was a result of two competitive effects: nucleation effect of filler and solidification effect of elastomer. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough SEBS elastomer. Spherulitic morphology of polypropylene matrix might affect some mechanical properties additionally. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41486.     

Morphology,mechanical properties and electromagnetic shielding effectiveness of poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene)/carbon nanotube nanocomposites: effects of maleic anhydride,carbon nanotube loading and processing method

Nanocomposites based on poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene) (SEBS) and carbon nanotubes (CNTs) (SEBS/CNT) as well as SEBS grafted with maleic anhydride (SEBS‐MA)/CNT were successfully prepared for electromagnetic shielding applications. Both SEBS/CNT and SEBS‐MA/CNT nanocomposites were prepared by melt compounding and were post‐processed using two different techniques: tape extrusion and compression moulding. The different nanocomposites were characterized by Raman spectroscopy and rheological analysis. Their mechanical properties, electrical properties (10^-2–10⁵ Hz) and electromagnetic shielding effectiveness (8.2–12.4 GHz) were also evaluated. The results showed that the CNT loading amount, the presence of MA in the matrix and the shaping technique used strongly influence the final morphologies and properties of the nanocomposites. Whilst the nanocomposite containing 8 wt% CNTs prepared by compression moulding presented the highest electromagnetic shielding effectiveness (with a value of 56.73 dB, which corresponds to an attenuation of 99.9996% of the incident radiation), the nanocomposite containing 5 wt% CNTs prepared by tape extrusion presented the best balance between electromagnetic and mechanical properties and was a good candidate to be used as an efficient flexible electromagnetic interference shielding material. © 2018 Society of Chemical Industry     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Solubility measurement of hydrogen,ethylene, and 1‐hexene in polyethylene films through an intelligent gravimetric analyzer

The solubility of hydrogen (H₂), ethylene (C₂H₄), 1‐hexene (C₆H₁₂), and the mixture of C₂H₄/1‐C₆H₁₂ in semicrystalline polyethylene (PE) films is measured using an intelligent gravimetric analyzer (IGA) in combination with prediction equations. For the pure‐component sorption in PE, the solubility of C₂H₄ and 1‐C₆H₁₂ decreases with the temperature, while that of H₂ exhibits an opposite variation tendency in the temperature range under test. For the C₂H₄/1‐C₆H₁₂ mixture, the co‐solubility is almost 10% smaller than the sum of the pure‐component solubility. 1‐C₆H₁₂ acts as a co‐solvent and C₂H₄ an antisolvent. Moreover, good consistency has been achieved between the measured data and the prediction results from the Sanchez‐Lacombe EOS model, demonstrating the reliability of the measurement approach employed in this work. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44507.     

ZrO2 functionalized graphene Oxide/SEBS‐Based nanocomposites for efficient electromagnetic interference shielding applications

ZrO₂‐coated graphene oxide (GO)/SEBS(styrene‐ethylene‐butylene‐styrene)‐based nanocomposites were prepared for use as an electromagnetic interference (EMI) shielding material. Transmission electron microscopy (TEM) reveals almost every individual GO is fully and homogeneously covered with uniform ZrO₂. X‐ray diffraction (XRD) patterns and Differential scanning calorimetry (DSC) revealed increased ordering of ‐(CH₂‐CH₂)n segments in the poly(ethylene‐co‐1‐butene) block of the SEBS matrix in the case of SEBS/ZrO₂‐coated graphene oxide composites than in the SEBS/pristine graphene oxide nanocomposite. Thermogravimetric analysis (TGA) proved better oxidation resistance of SEBS/ZrO₂‐coated GO nanocomposite compared to that of SEBS/pristine GO nanocomposite. The present nanocomposites exhibited excellent EMI shielding effectiveness (SE) over X‐band (8.2 GHz–12.4 GHz) with EMI SE of 37.9 dB. J. VINYL ADDIT. TECHNOL., 25:E130–E136, 2019. © 2018 Society of Plastics Engineers     

Compatibilization of kraft lignin‐polyethylene composites using unreactive compatibilizers

This article presents a novel approach to compatibilize Kraft lignin with polyethylene that involves the use of modified poly (styrene‐co‐ethylene‐co‐butylene‐co‐styrene) (SEBS) as unreactive compatibilizers. As SEBS shows no compatibilizing effect on Kraft lignin‐polyethylene composites, SEBS was functionalized via nitration followed by amination to obtain nitrated (SEBS‐NO₂) and aminated (SEBS‐NH₂) SEBS. The compatibilizing effects of SEBS derivatives were studied by means of morphological and mechanical analyses. The results show that SEBS‐NO₂ is less effective than SEBS‐NH₂, the later displaying comparable compatibilizing efficiency to a commercial reactive compatibilizer based on maleated polyethylene. Overall, compatibilization was found to decrease lignin particle size. Addition of SEBS‐NH₂ varying between 1% and 10% improved the tensile strength of composites by up to 96%, elongation at break by up to 64%, and impact strength by up to 48%. Finally, the crystallinity and density of the resulting composites were also studied. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41040.