Interfacial interactions in concretes with silica fume and SBR latex

This paper deals with the effect of silica fume and styrene-butadiene latex (SBR) on the microstructure of the interfacial transition zone (ITZ) between Portland cement paste and aggregates (basalt). Scanning electron microscope (SEM) equipped with energy dispersive X-ray analysis system (EDX) was used to determine the ITZ thickness. In the plain concrete a marked ITZ around the aggregate particles (55 μm) was observed, while in concretes with silica fume or latex SBR the ITZ was less pronounced (35–40 μm). However, better results were observed in concretes with silica fume and latex SBR (20–25 μm).     

Micro-analysis of the role of interfacial transition zone in “salt weathering” on concrete

When concrete elements are partially immersed in the sulfate environment, researchers always attribute “salt weathering”, “salt crystallization” or “physical attack” to the failure of concrete. However, there were few micro-analysis evidences to support this view. In this paper, an attempt was carried out to study whether salt weathering is really responsible for the concrete damage.As we know, the interfacial transition zone (ITZ) between paste and aggregate plays a determining role in the performance of concrete. In this paper, we focused on the role of ITZ in “salt weathering” on concrete. Concrete specimens, made with coarse aggregate and cement paste, were partially exposed to a 5% sodium sulfate solution and a 5% magnesium sulfate solution respectively, in a controlled environment (20 ± 2 °C, and 60 ± 5% RH). After 8 months of exposure, a micro-analysis is performed by means of XRD, ESEM and EDS. The experimental results showed that, in the upper part of concrete above the Na₂SO₄ solution, damage initiated in the ITZ between paste and aggregate due to the formation of ettringite and gypsum. Salt crystallization cannot occur on the paste surface in the ITZ, but it was found on the aggregate surface after damage initiation due to chemical sulfate attack. On the other hand, salt crystallization could occur in the carbonated concrete. There was no trace of salt crystallization in the concrete partially exposed to MgSO₄ solution.     

尺寸效应对水泥净浆与粗骨料界面黏结性能的影响

分析了粗骨料的尺寸对混凝土过渡区界面黏结性能的影响,并通过劈裂抗拉试验、压剪试验获得了粗骨料和硬化水泥浆之间的劈裂抗拉强度及抗剪强度.结果表明:粗骨料的尺寸对界面过渡区的黏结性能有较大的影响,界面黏结强度随粗骨料尺寸的增大而减小;水灰比越低,界面黏结性能越好;粗骨料的类型对界面过渡区黏结性能也有较大性能的影响.     

Delayed ettringite formation (DEF) in mortars of white cement

In this study white cement CEM I-52.5 and white limestone cement CEM II-LL, A and B, with 15% and 25% limestone substitution, were studied. The way delayed ettringite forms, due to exposure to high temperatures (50 °C) and external sulphate attacks, was examined in the mortar samples.The mortars were immersed at 50 °C for 180 days in: (a) a saturated Ca(OH)₂ solution and (b) a 5% Na₂SO₄ solution. During the experiment’s duration, the mortar samples were being observed visually on a regular basis while their expansion was estimated on a weekly basis by measuring the change of length with a micrometer. At the end of the experiment, the mortar samples’ compressive strength was determined and the deterioration products were identified through means of X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM-EDAX), Thermogravimetry (TG) and Infra-Red Spectroscopy (FT-IR).Concluding it is evident that the amount of ettringite is proportional to the C₃A content of cement. Sulphates amount in cement is the controlling factor for heat induced ettringite formation since when they are consumed the reaction stops. On the other hand in the case of external sulphate attack another important controlling factor is the compressive strength of the cement; the higher compressive strength the lower the risk of expansion. Finally, in the case of external sulphate attack, limestone, when added to cement, was proved to enhance the durability against sulphates attack when compared to a cement of the same class.     

Effects of limestone replacement ratio on the sulfate resistance of Portland limestone cement mortars exposed to extraordinary high sulfate concentrations

A comparative study has been performed on the sulfate resistance of Portland limestone cement (PLC) mortars exposed to extraordinary high sulfate concentrations (200 g/l). PLCs have been prepared by using two types of clinkers having different C₃S/C₂S ratios and interstitial phase morphologies. Blended cements have been prepared by replacing 5%, 10%, 20% and 40% of clinker with limestone. Cubic (50 × 50 × 50 mm) and prismatic (25 × 25 × 285 mm) cement mortars were prepared. After two months initial water curing, these samples were exposed to three different sulfate solutions (Na₂SO₄ at 20 °C and 5 °C, MgSO₄ at 5 °C). Solutions were not refreshed and pH values of solutions were monitored during the testing stage. The compressive strength and length changes of samples have been monitored for a period of 1 year. Additional microstructural analyses have been conducted by XRD and SEM/EDS studies. Results indicated that in general, limestone replacement ratio and low temperature negatively affect the sulfate resistance of cement mortars. Additionally, clinkers of high C₃S/C₂S ratios with dendritic interstitial phase structure were found to be more prone to sulfate attack in the presence of high amounts of limestone.From the results, it is postulated that in the absence of solution change, extraordinary high sulfate content modified the mechanism of sulfate reactions and formation of related products. At high limestone replacement ratios, XRD and SEM/EDS studies revealed that while ettringite is the main deterioration product for the samples exposed to Na₂SO₄, gypsum and thaumasite formation were dominant products of deterioration in the case of MgSO₄ attack. It can be concluded that, the difference between reaction mechanisms of Na₂SO₄ and MgSO₄ attack to limestone cement mortars strongly depends on the pH change of sulfate solutions.     

Durability of gamma irradiated polymer-impregnated blended cement pastes

This study is focusing on durability of the neat blended cement paste as well as those of the polymer-impregnated paste towards seawater and various concentrations of magnesium sulfate solutions up to 6 months of curing. The neat blended cement paste was prepared by a partial substitution of ordinary Portland cement with 5% of active rice husk ash (RHA). These samples were cured under tap water for 7 days. A similar paste was impregnated with unsaturated polyester resin (UPE) followed by gamma rays ranging from 10 to 50 kGy. The obtained data indicated that the polymer-impregnated specimens higher values of compressive strength than those of the neat blended cement paste. In addition, the polymer-impregnated blended cement specimens irradiated at a dose of 30 kGy and neat blended cement specimens were immersed in seawater and different concentrations of magnesium sulfate solutions namely, 1%, 3% and 5% up to 6 months. The results showed that the polymer-impregnated blended cement (OPC–RHA–UPE) paste irradiated at a dose of 30 kGy has a good resistance towards sulfate and seawater attack as compared to the neat blended cement (OPC–RHA) paste. These results were confirmed by scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP) studies.     

Performance of limestone cement mortars in a high sulfates environment

With the aim of studying the influence of cement composition on resistance in high sulfates environment, standard mortars have been produced using ordinary Portland cement (CEM I – 32.5) and limestone cement with 35% limestone (CEM II/B-LL – 32.5). The pore size distribution of the cement pastes was measured. The mortars were immersed in a 5% Na₂SO₄ solution at 20 °C for 1.5 years and the caused deterioration was been visually observed at a regular basis. Furthermore, the mortars expansion was being estimated by measuring the change of length. At the end of the experiment the compressive strength of the mortars was measured. The deterioration products of the mortars have been identified by means of X-ray diffraction, optical microscopy and environmental scanning electron microscopy. The limestone cement based mortar presented cracking that started at the age of 6 months and continued throughout the experiment. It also displayed high expansion after 250 days of immersion in a 5% Na₂SO₄ caused, as proved using the analytical techniques, by the formation of gypsum and ettringite. Concluding, the cement with 35% limestone did not perform as well as ordinary Portland cement under the most aggressive laboratory conditions. Hence, it is obvious that the addition of limestone in the cement leads to a totally different behaviour than Portland cement with respect to the resistance in high sulfates environment.     

Thaumasite form of sulfate attack in limestone cement mortars: A study on long term efficiency of mineral admixtures

Concrete and mortar made from limestone cement may exhibit a lack of durability due to the formation of thaumasite. The addition of minerals that improve the concrete durability is expected to slow down the formation of thaumasite. In this work the effect of natural pozzolana, fly ash, ground granulated blastfurnace slag and metakaolin on the thaumasite formation in limestone cement mortar is examined. A limestone cement, containing 15% w/w limestone, was used. Mortar specimens were prepared by replacing a part of limestone cement with the above minerals. The specimens were immersed in a 1.8% MgSO₄ solution and cured at 5 and 25 °C. The status of the samples after a storage period of 5 years was reported based on visual inspection, compressive strength, mass measurements, ultrasonic pulse velocity measurements and analytical techniques. It is concluded that the use of specific minerals, as partial replacement of cement, inhibits thaumasite formation in limestone cement mortar.     

How sulfates and increased temperature affect delayed ettringite formation (DEF) in white cement mortars

In this study,white cement CEM I and white limestone cement CEM II-LL A and Β with 15%, 25% and 35% limestone substitution were studied. The way delayed ettringite is forming due to exposure to increased temperature (50 °C) and external sulfate attack was examined in mortar samples which were immersed for 90 days in three different solutions: (a) saturated solution Ca(OH)₂ at 50 °C, (b) saturated solution of Ca(OH)₂ at 20 °C and (c) 5% w/w Na₂SO₄ solution at 50 °C. During this period mortar samples were visually observed regularly while their expansion was estimated on a weekly basis by measuring the change of length with a micrometer. At the end of the 90-days period the compressive strength of the mortars was determined and the deterioration products were identified through means of X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and thermogravimetric analysis (DTG). The results of this study show that DEF occurred in two forms. Samples cured at increased temperature contained DEF type I, which caused mediocre expansion and damage. Samples cured at increased temperature in the presence of sulfates produced DEF type II, which caused significant damage on the surface and exhibited high expansion.     

Durability design and performance of self-consolidating lightweight concrete

In terms of the durability, the reduction in cement paste is crucial to both volume stability and long-term performance of concrete. The objective of this paper is to compare the performance of lightweight concrete under different w/cm ratio and different cement paste content. The slump and slump flow spread of fresh self-consolidating lightweight concrete (SCLWC) are designed to be within 230–270 and 550–650 mm, respectively. The test results indicate that the 91-day compressive strength of SCLWC is up to 56 MPa when cement content is 386 kg/m³ and water content is 150 kg/m³. If enough cement paste is used, then the less the paste amount and the denser the packing of aggregate, the higher the strength efficiency of cement and the electric resistance, and the lower the chloride ion penetrability capacity of SCLWC.     

Effects of elevated water temperatures on interfacial delaminations,failure modes and shear strength in externally-bonded CFRP-concrete beams using infrared thermography,gray-scale images and direct shear test

This paper reports the results of a durability study of the effects of exposing externally-bonded CFRP-concrete beams to three elevated water temperatures (25 °C, 40 °C and 60 °C). The effects of the heated water environments on the adhesive bonding layer between the CFRP and concrete beams were evaluated by quantifying: (1) the changes of delaminations within the adhesive bonding layer, (2) the changes in resistance to direct shear force and (3) the changes of failure mode distribution. Before the exposure, the condition of the adhesive bonding layer was inspected by infrared thermography (IRT). After exposure, the deterioration of the same bonding layer and failure mode distributions were measured by analyzing the visual photos on the failed CFRP strips. The failure modes were found to be affected largely by the combined effect of elevated temperature and moisture ingress, in which three types were identified: failure at concrete beams, at adhesive bonding layer and interface between CFRP strip and concrete. With these methods, results of 54 specimens show that the adhesive bonding layers of all the specimens had gradually deteriorated in the 40 °C and 60 °C water baths. This deterioration was due to the weakening of the adhesive bonding layers when the glass transition temperature (T_g) or the heat distortion temperature (HDT) was approached or even exceeded, and gradual development of delaminations at adhesive bonding layer.     

Preparation of load-bearing building materials from autoclaved phosphogypsum

Previous studies have been carried out on calcined phosphogypsum (PG) for making the building materials. The present study was focused on autoclaved PG and its use in making load-bearing wall bricks. Autoclaved PG was prepared from original waste PG with steam pre-treatment. The crystalline phase, morphology, and thermal characteristics of original waste PG and autoclaved PG were investigated by XRD, SEM, and SDT. Then bricks of the size of Chinese standard brick were prepared from different types of PG in the PG-fly ash–lime–sand system. Results showed that the compressive strength of bricks from autoclaved PG by lower-pressure steam of 0.12 MPa, 120 °C for 16 h was much higher. The flexural strength and compressive strength of the bricks could reach 4.0 MPa and 15.0 MPa, respectively. The durability of the bricks was investigated by 15 freezing–thawing cycles at temperatures from ?20 °C to 20 °C, and the weight loss was only 0.029% after all of cycles. Hemihydrates (CaSO₄ · 0.5H₂O) were dehydrated products from dihydrates in original PG with lower-pressure steam treatment, and hemihydrates were susceptible to absorbing the humidity and were transformed into densified re-crystallization gypsum (CaSO₄ · 2H₂O) that contributed to the final strength of bricks. Microstructural characteristics of bricks were investigated by XRD and SEM. Tobermorite was the significant hydrated product, which contributed to the strength of bricks. The use of autoclaved PG for making load-bearing wall bricks was recommended instead of conventional burnt clay bricks.     

Influence of silica fume on the interfacial bond between aggregate and matrix in near-surface layer of concrete

The interfacial transition zone (ITZ) as the weakest position in concrete is always paid much attention. This paper presents the results of an investigation on the interfacial bond between aggregate and matrix in the near surface layer of concrete at the macro- and micro-level. Specimens with different silica fume additions (0%, 6%, 9% and 12% by mass of cement) and cement dosages (400 and 450 kg/m³) were prepared by removing certain near-surface mortar and making coarse aggregates exposed. The interfacial bond properties were evaluated by the pull-out test and microhardness test. It was found that ITZs around the near-surface-zone aggregate were influenced not only by the Wall Effect and the accumulation of microbleeding water under aggregate, but also by the near-surface weakness zone effect. The additional silica fume can successively enhance the interfacial bond strength, decrease the thickness of the near-surface weakness zone and improve ITZs in the near-surface layer of concrete.     

Mechanical and durability properties of concretes containing paper-mill residuals and fly ash

The use of paper-mill residuals in concrete formulations was investigated as an alternative to landfill disposal. The mechanical and durability properties of concrete containing paper-mill residuals collected from a wastewater treatment-plant were evaluated. Class F fly ash was used as a replacement for Portland cement (PC) when incorporated into concrete mixtures containing paper-mill residuals and the resulting products were compared to normal concrete. Compressive, splitting tensile, flexural strength and drying shrinkage tests were carried out to evaluate the mechanical properties for up to 90 days. Rapid chloride-permeability tests and initial surface-absorption tests were carried out at 28 days to determine the durability properties. Concrete containing paper-mill residuals showed improvement in the durability test results when PC was replaced with class F fly ash.     

The assessment of porosity and pore size distribution of limestone Portland cement pastes

The cement production industry is one of the most energy and raw materials consuming one. Over the last years a great effort is performed in order to substitute clinker for less energy demanding materials. Nevertheless, construction industry needs durable materials with improved properties. Limestone is being used in blended cements widely. The most important parameter that affects all the properties of cement paste is its pore structure. In this study, four different limestone cements were produced and their pore structure was determined by means of mercury intrusion porosimetry (MIP) and nuclear magnetic resonance (NMR) cryoporometry. The conclusion of the study was that limestone addition affects the pore structure of the cement paste by increasing linearly the size of capillary pores from 20 nm to 40 nm when the maximum amount (35%) of limestone that is allowed by EN 197-1 is used. On the other hand the threshold diameter decreases exponentially and it is evident that limestone hardened cement pastes have many pores of the same size due to the filling effect that minerals additives have. Furthermore, limestone decreases the size of gel pores which is related to higher hydration rates. Hence, the use of limestone in cement produces a material that is structurally adequate to be used in construction.     

Influence of activator on the strength and drying shrinkage of alkali-activated slag mortar

The development of new binders, as an alternative to traditional cement, by the alkaline activation of industrial by-products (i.e. ground granulated slag and fly ash) is an ongoing research topic in the scientific community [Puertas F, Amat T, Jimenez AF, Vazquez T. Mechanical and durable behaviour of alkaline cement mortars reinforced with polypropylene fibres. Cem Concr Res 2003;33(12): 2031–6]. The aim of this study was to investigate the feasibility of using and alkaline activated ground Turkish slag to produce a mortar without Portland cement (PC).Following the characterization of the slag, mortar specimens made with alkali-activated slag were prepared. Three different activators were used: liquid sodium silicate (LSS), sodium hydroxide (SH) and sodium carbonate (SC) at different sodium concentrations. Compressive and flexural tensile strength of alkali-activated slag mortar was measured at 7-days, 28-days and 3-months. Drying shrinkage of the mortar was measured up to 6-months. Setting times of the alkali-activated slag paste and PC paste were also measured.Setting times of LSS and SH activated slag pastes were found to be much slower than the setting time of PC paste. However, slag paste activated with SC showed similar setting properties to PC paste.LSS, SH and SC activated slag mortar developed 81, 29, and 36 MPa maximum compressive strengths, and 6.8, 3.8, and 5.3 MPa maximum flexural tensile strengths at 28-days. PC mortar developed 33 MPa compressive strength and 5.2 MPa flexural tensile strength. LSS and SH activated slag mortars were found to be more brittle than SC activated slag and PC mortars.Slag mortar made with LSS had a high drying shrinkage, up to six times that of PC mortar. Similarly, slag mortar made with SH had a shrinkage up to three times that of PC mortar. However, SC activated slag mortar had a lower or comparable shrinkage to PC mortar. Therefore, the use of SC as an activator for slag mortar is recommended, since it results in adequate strength, similar setting times to PC mortar and comparable or lower shrinkage.     

Development of alpha plaster from phosphogypsum for cementitious binders

Efforts have been made to make high strength alpha plaster from phosphogypsum, a by-product of phosphoric acid industry. Phosphogypsum was autoclaved in slurry form (phosphogypsum 50% + water 50%, by wt.) in the laboratory at different steam pressures for different durations in presence of chemical admixtures. It was found that with small quantity of chemical admixture (sodium succinate/potassium citrate/sodium sulphate), alpha plaster of high strength can be produced. The optimum pressure and duration of autoclaving was found to be as 35 psi and 2.0 h, respectively. The alpha plaster was examined for making cementitious binders by admixing hydrated lime, fly ash, granulated blast furnace slag, marble dust and chemical additives with alpha plaster. Data showed that cementitious binder of compressive strength of 22.0 and 30 MPa (at 28 days of curing at 40° and 50 °C) and low water absorption was produced. DTA and SEM studies of the binder showed formation of CSH, ettringite and C₄AH₁₃ as main cementitious products to give strength.     

Effect of micro-silica loading on the mechanical and acoustic properties of cement pastes

This study aimed at investigating the role of ultra fine sand (UFS) in enhancing the mechanical and acoustic properties of cementitious pastes. The microstructural origin of these properties was also identified and compared to the conventional materials. The maximum particle size of the UFS used was 100 μm (100% passing) while 50% of the UFS had less than 20 μm in diameter. Ordinary Portland cement (OPC) was partially substituted by UFS at 1%, 2%, 3%, 4%, 5%, 7.5% and 10% by weight of binder. The blended compounds were prepared using the standard water of consistency. Test samples with dimension of 20 × 20 × 20 mm and 40 × 40 × 160 mm were cast for compression and bending strengths tests, respectively. Circular samples with diameters of about 100 and 29 mm and average thickness of about 30 mm were used for sound absorption tests. All samples were kept in molds for 24 h, and then de-molded and allowed to cure in water for 28 days. The specimens were dried at a temperature of 105 °C for 24 h in an oven before testing. It was found that as the loading of UFS increases both the compressive and bending strength increase up to about 5% UFS loading, then a decrease in these properties was observed. This can be attributed to the pozzolanic effect of UFS resulting in enhancing the chemical reaction between free lime in cement and silica producing more hydration products that makes the paste more homogeneous and dense. In addition, the dispersed UFS has improved the filling effect allowing denser packing of the paste. These dense microstructural features were captured by scanning electron microscope (SEM) examination of the 5% UFS modified compound. The results also showed that, the sound absorption and noise reduction coefficient (NRC) for modified cement paste decreases with the increase of UFS up to 5% and this may be due to the decrease in porosity. However, the NRC began to increase at UFS loadings of 7.5% and 10% due to the increase in the porosity of the compounds.     

Preparation and characterisation of fly ash based geopolymer mortars

Geopolymer mortars with varying levels of sand aggregate were prepared and their physical and mechanical properties studied. The geopolymer binder to sand aggregate weight ratio was varied from 9 to 1. Compressive strength and Young’s modulus of the fly ash based geopolymer paste were 60 MPa and 2.27 GPa and these values did not change significantly with addition of up to 50 wt.% sand aggregate. Geopolymer binder exhibited strong bonding to the sand aggregate. Increasing sand content without increasing the amount of alkaline activator resulted in a decreasing level of geopolymerisation within the binder system.     

Influence of temperature on induction period and on ultimate porosity of hardening cement paste

Influence of curing temperature applied to hardening cement paste during the early induction period of hydrating (which is closely connected with so-called workability of concrete mixture i.e., with the period during which the material is formative and may be transported) on duration of the induction period and on the ultimate porosity of hardened samples was experimentally determined. Duration of the induction period was determined by means of electrical resistance measurements and ultimate porosity by means of the mercury intrusion porosimetric measurements. It was proved that temperatures within the range 10–65 °C whenever applied solely during induction period have a significant effect on induction period with no measurable effect on ultimate porosity of hardened cement paste.