Enhanced room temperature response of SnO2 thin film sensor loaded with Pt catalyst clusters under UV radiation for LPG

The room temperature response characteristics of SnO₂ thin film sensor loaded with platinum catalyst clusters are investigated for LPG under the exposure of ultraviolet radiation. The SnO₂-Pt cluster sensor structures have been prepared using rf sputtering. Combined effect of UV radiation exposure (λ = 365 nm) and presence of Pt catalyst clusters (10 nm thick) on SnO₂ thin film sensor surface is seen to lead to an enhanced response (4.4 × 10³) for the detection of LPG (200 ppm) at room temperature whereas in the absence of UV illumination a comparable response (∼5 × 10³) could be obtained but only at an elevated temperature of 220 °C. The present study therefore investigates the effect of UV illumination on LPG sensing characteristics of SnO₂ sensors loaded with Pt clusters of varying thickness values. Results indicate the possibility of utilizing the sensor structure with novel dispersal of Pt catalyst clusters on SnO₂ film surface for efficient detection of LPG at room temperature under the illumination of UV radiations.     

SnO2 thin film sensor with enhanced response for NO2 gas at lower temperatures

Semiconducting SnO₂ thin films having higher value of electrical conductivity have been deposited using RF sputtering technique in the reactive gas environment (30% O₂ + 70% Ar) using a metallic tin (Sn) target for detection of oxidizing NO₂ gas. The effect of growth pressure (12-18 mTorr) on the surface morphology and structural property of SnO₂ film was studied using Atomic force microscopy (AFM), Scanning electron microscopy (SEM) and X-ray Diffraction (XRD) respectively. Film deposited at 16 mTorr sputtering pressure was porous with rough microstructure and exhibits high sensor response (∼2.9 × 10⁴) towards 50 ppm NO₂ gas at a comparatively low operating temperature (∼100 °C). The sensor response was found to increase linearly from 1.31 × 10² to 2.9 × 10⁴ while the response time decrease from 12.4 to 1.6 min with increase in the concentration of NO₂ gas from 1 to 50 ppm. The reaction kinetics of target NO₂ gas on the surface of SnO₂ thin film at the Sn sites play important role in enhancing the response characteristics at lower operating temperature (∼100 °C). The results obtained in the present study are encouraging for realization of SnO₂ thin film based sensor for efficient detection of NO₂ gas with low power consumption.     

Influence of Cs doping in spray deposited SnO2 thin films for LPG sensors

Detection of low concentrations of petroleum gas was achieved using transparent conducting SnO₂ thin films doped with 0–4 wt.% caesium (Cs), deposited by spray pyrolysis technique. The electrical resistance change of the films was evaluated in the presence of LPG upon doping with different concentrations of Cs at different working temperatures in the range 250–400 °C. The investigations showed that the tin oxide thin film doped with 2% Cs with a mean grain size of 18 nm at a deposition temperature of 325 °C showed the maximum sensor response (93.4%). At a deposition temperature of 285 °C, the film doped with 3% Cs with a mean grain size of 20 nm showed a high response of 90.0% consistently. The structural properties of Cs-doped SnO₂ were studied by means of X-ray diffraction (XRD); the preferential orientation of the thin films was found to be along the (3 0 1) directions. The crystallite sizes of the films determined from XRD are found to vary between 15 and 60 nm. The electrical investigations revealed that Cs-doped SnO₂ thin film conductivity in a petroleum gas ambience and subsequently the sensor response depended on the dopant concentration and the deposition temperature of the film. The sensors showed a rapid response at an operating temperature of 345 °C. The long-term stability of the sensors is also reported.     

Sprayed CdIn2O4 thin films for liquefied petroleum gas (LPG) detection

Nanocrystalline cadmium indium oxide (CdIn₂O₄) thin films of different thicknesses were deposited by chemical spray pyrolysis technique and utilized as a liquefied petroleum gas (LPG) sensors. These CdIn₂O₄ films were characterized for their structural and morphological properties by means of X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The dependence of the LPG response on the operating temperature, LPG concentration and CdIn₂O₄ film thickness were investigated. The results showed that the phase structure and the LPG sensing properties changes with the different thicknesses. The maximum LPG response of 46% at the operation temperature of 673 K was achieved for the CdIn₂O₄ film of thickness of 695 nm. The CdIn₂O₄ thin films exhibited good response and rapid response/recovery characteristics to LPG.     

Nano particulate SnO2 based resistive films as a hydrogen and acetone vapour sensor

SnCl₂ (solution) was spin coated on soda lime glass and Al₂O₃ substrate to obtain nano-particulate tin oxide film, directly by sintering at 550 °C for 40 minutes (min). The surface morphology and crystal structure of the tin oxide films were analyzed using atomic force microscopy (AFM) and X-ray diffraction (XRD). The size of SnO₂ nanostructure was determined from UV-vis and found to be ?3 nm. These films were tested for sensing H₂ concentration of 0.1-1000 ppm at optimized operating temperature of 265 °C. The results showed that sensitivity (R_air/R_gas per ppm) goes on increasing with decreasing concentration of test gas, giving concentration dependent changes. Special studies carried out at low concentration levels (0.1-1 and 1-10 ppm) of H₂, give high sensitivity (200 × 10⁻³/ppm) for lowest concentration (0.1-1 ppm) of H₂. The selectivity for H₂ against relative humidity (RH), CO₂, CO and LPG gases is also good. The sensor, at operating temperature of 200 °C, is showing nearly zero response to 300 ppm of H₂, and offering response to acetone vapour of 11 ppm. Selectivity for acetone against RH% and CO₂ was also studied. These sensors can be used as H₂ sensor at an operating temperature of 265 °C, and as an acetone sensor at the operating temperature of 200 °C.     

Fe2O3 modified thick films of nanostructured SnO2 powder consisting of hollow microspheres synthesized from pyrolysis of ultrasonically atomized aerosol for LPG sensing

Nanostructured hollow spheres of SnO₂ with fine nanoparticles were synthesized by ultrasonic atomization. Thick film gas sensors were fabricated by screen printing technique. Different surface modified films (Fe₂O₃ modified SnO₂) were obtained by dipping them into an aqueous solution (0.01 M) of ferric chloride for different intervals of time followed by firing at 500 °C. The structural and microstructural studies of the samples were carried out using XRD, SEM, and TEM. The sensing performance of pure and modified films was studied by exposing various gases at different operating temperatures. One of the modified sample exhibited high response (1990) to 1000 ppm of LPG at 350 °C. Optimum amount of Fe₂O₃ dispersed evenly on the surface_, adsorption and spillover of LPG on Fe₂O₃ misfits and high capacity of adsorption of oxygen on nanostructured hollow spheres may be the reasons of high response.     

Improved crystalline structure and H2S sensing performance of CuO-Au-SnO2 thin film using SiO2 additive concentration

In situ SiO₂-doped SnO₂ thin films were successfully prepared by liquid phase deposition. The influence of SiO₂ additive as an inhibitor on the surface morphology and the grain size for the thin film has been investigated. These results show that the morphology of SnO₂ film changes significantly by increasing the concentration of H₂SiF₆ solution which decreases the grain size of SnO₂. The stoichiometric analysis of Si content in the SnO₂ film prepared from various Si/Sn molar ratios has also been estimated. For the sensing performance of H₂S gas, the SiO₂-doped Cu-Au-SnO₂ sensor presents better sensitivity to H₂S gas compared with Cu-Au-SnO₂ sensor due to the fact that the distribution of SiO₂ particles in grain boundaries of nano-crystallines SnO₂ inhibited the grain growth (<6 nm) and formed a porous film. By increasing the Si/Sn molar ratio, the SiO₂-doped Cu-Au-SnO₂ gas sensors (Si/Sn = 0.5) exhibit a good sensitivity (S = 67), a short response time (t_90% < 3 s) and a good gas concentration characteristic (α = 0.6074). Consequently, the improvement of the nano-crystalline structures and high sensitivity for sensing films can be achieved by introducing SiO₂ additive into the SnO₂ film prepared by LPD method.     

High-performance liquefied petroleum gas sensing based on nanostructures of zinc oxide and zinc stannate

Toxic and combustible gas detection plays a major role in environmental air quality monitoring. Real-time monitoring of hazardous gases and signal of accidental leakages is of great importance owing to the concern for safety requirements in industries and household applications. A simple and economical method for the fabrication of highly sensitive zinc oxide (ZnO) nanorods based gas sensors for detecting low concentrations of Liquefied Petroleum Gas (LPG) was studied in this work. Platinum (Pt) nanoparticles were deposited on the sensing medium which acts as catalysts to improve the sensor performance. The change in electrical resistance of the metal oxide semiconductor for varying concentrations of LPG was measured. Maximum response of 59% was achieved for 9000 ppm LPG at 250 °C. Further to improve the sensing performance of the sensor towards LPG, surface modification of ZnO nanorods using zinc stannate (Zn₂SnO₄) microcubes was performed. High response of 63% was observed for 3000 ppm LPG at 250 °C. Significant improvement in response of the sensor with Zn₂SnO₄ microcubes on ZnO nanorods was observed when compared to sensor with ZnO nanorods.     

Examination of Au/SnO2 core-shell architecture nanoparticle for low temperature gas sensing applications

Au/SnO₂ core-shell structure nanoparticles (NPs) were synthesized using two methods, microwave and conventional precipitation. In both cases, the size of the Au core was 12-18 nm and the thickness of the SnO₂ shell was 8-12 nm. The particle size of SnO₂ synthesized using the microwave and precipitation method was 3-5 nm and 1-2 nm, respectively. Upon heating to 400-600 °C, both particles maintained their core-shell morphology but the smaller SnO₂ particles prepared using the precipitation method were more sintered. The resistance changes in films of these particles were measured as a function of CO concentration. The Au/SnO₂ particles prepared using the microwave method showed higher sensor response than those prepared using the precipitation method, even providing a significant signal at testing temperatures approaching ambient conditions, thereby affording a new class of material for gas sensing. Both sets of core-shell particles showed higher sensor response than the SnO₂ nanoparticles. The role of the Au core as a catalyst in improving the adsorption and oxidation of CO gas is important for improving the low temperature response. In addition, the maintenance of the size of SnO₂ in the microwave method during sintering contributed to the higher response towards CO sensing.     

Fabrication at wafer level of miniaturized gas sensors based on SnO2 nanorods deposited by PECVD and gas sensing characteristics

SnO₂ nanorods were successfully deposited on 3″ Si/SiO₂ wafers by inductively coupled plasma-enhanced chemical vapour deposition (PECVD) and a wafer-level patterning of nanorods layer for miniaturized solid state gas sensor fabrication were performed. Uniform needle-shaped SnO₂ nanorods in situ grown were obtained under catalyst- and high temperature treatment-free growth condition. These nanorods have an average diameter between 5 and 15 nm and a length of 160-300 nm. The SnO₂-nanorods based gas sensors were tested towards NH₃ and CH₃OH and gas sensing tests show remarkable response, showing promising and repeatable results compared with the SnO₂ thin films gas sensors.     

The low temperature polysilicon (LTPS) thin film MOS Schottky diode on glass substrate for low cost and high performance CO sensing applications

The Au/SnO₂/n-LTPS MOS Schottky diode prepared on a glass substrate for carbon monoxide (CO) sensing applications is studied. The n-LTPS (n-type low temperature polysilicon) is prepared by excimer laser annealing and PH₃ plasma treatment of an amorphous Si thin film on glass substrate. The developed Schottky diode exhibits a high relative response ratio of ∼546% to 100 ppm CO ambient under condition of 200 °C and −3 V bias. The response ratio is better than the reported SnO₂ based resistive type CO sensors of 100% and 37%, respectively on poly-alumina and glass substrates or comparable to 390% of Pt-AlGaN/GaN Schottky diode CO sensor. Thus, the Au/SnO₂/n-LTPS Schottky diode has the potential to develop a low cost high performance CO sensor.     

Facile synthesis of hierarchical SnO2 semiconductor microspheres for gas sensor application

Hierarchical SnO₂ microspheres were synthesized by a hydrothermal method at 140 °C using stannic chloride hydrate and sodium hydroxide as starting materials. The individual hierarchical SnO₂ microsphere ranged from 700 to 900 nm in diameter. After these microspheres were heated at 600 °C for 2 h, the spheres were cross-linked into clusters by short SnO₂ nanorods as revealed by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Most importantly, SnO₂ hierarchical microsphere sensor exhibits excellent selectivity and fast response to ethanol. Response and recovery times were 0.6 s and 11 s when the sensor was exposed to 50 ppm ethanol at an operating temperature of 300 °C. Thus, hierarchical structures play a significant role in the field of gas sensing.     

Enhanced wetting properties of silicon mesh microchannels coated with SiO2/SnO2 nanoparticles through layer-by-layer self assembly

The enhanced wetting property of silicon mesh microchannels coated with SiO₂/SnO₂ nanoparticles is presented in this paper. The SiO₂/SnO₂ bi-layers are prepared using layer-by-layer nano self assembly. It is found that the silicon mesh microchannels are super hydrophilic and demonstrated powerful capillary. The capillary rise rate is characterized by measuring the front location of liquid on the silicon mesh surface, laid on a 45° inclined platform. For a silicon mesh sample with an overall dimension of 25 mm × 25 mm, when the microchannel width is 0.5 mm, the liquid front can reach the top edge of the sample in approximately 30 s. The mesh silicon surface with a SiO₂/SnO₂ multilayer film presented in this paper has better wettability and higher capillary pressure than other hydrophilic surfaces reported. The results provide a new way to improve the capillary in microchannels with enhanced super hydrophilic surfaces in microchannels for variety of micro/nanofluidic applications.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.     

Dispersive SnO2 nanosheets: Hydrothermal synthesis and gas-sensing properties

SnO₂ nanosheets with the thickness of 10 nm were successfully synthesized by a simple hydrothermal process at 180 °C for 12 h. The samples were characterized by X-ray power diffraction, scanning electron microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy. The sensor performance of the as-prepared SnO₂ nanosheets for ethanol and carbon monoxide was measured. The results indicate that the sensor exhibited high response, quick response-recovery kinetics, and good repeatability.     

Highly sensitive SnO2 thin film with low operating temperature prepared by sol–gel technique

Sol–gel dip coating technique was employed to prepare Cu-doped SnO₂ thin films, which were able to detect H₂S gas at room temperature with high sensitivity and revealed fast response characteristics. The highest sensor response (the ratio of resistance in air versus in H₂S) was 3648 under H₂S concentration of 68.5 ppm at room temperature. Recoverability of the thin films appeared when the temperature raised to 50 °C. The films were analyzed by means of XRD and the dried gel powder was studied by TG-DTA test. Influences of sintering temperature and doping level on the H₂S response are discussed. The average grain size of the SnO₂ was about 25 nm.     

Analyte selective response in solution-deposited tetrabenzoporphyrin thin-film field-effect transistor sensors

Organic thin film transistor (OTFT) chemical sensors rely on the specific electronic structure of the organic semiconductor (OSC) film for determining sensor stability and response to analytes. The delocalized electronic structure is influenced not only by the OSC molecular structure, but also the solid state packing and film morphology. Phthalocyanine (H₂Pc) and tetrabenzoporphyrin (H₂TBP) have similar molecular structures but different film microstructures when H₂Pc is vacuum deposited and H₂TBP is solution deposited. The difference in electronic structures is evidenced by the different mobilities of H₂TBP and H₂Pc OTFTs. H₂Pc has a maximum mobility of 8.6 × 10⁻⁴ cm² V⁻¹ s⁻¹ when the substrate is held at 250 °C during deposition and a mobility of 4.8 × 10⁻⁵ cm² V⁻¹ s⁻¹ when the substrate is held at 25 °C during deposition. Solution deposited H₂TBP films have a mobility of 5.3 × 10⁻³ cm² V⁻¹ s⁻¹, which is consistent with better long-range order and intermolecular coupling within the H₂TBP films compared to the H₂Pc films. Solution deposited H₂TBP also exhibits a textured film morphology with large grains and an RMS roughness 3-5 times larger than H₂Pc films with similar thicknesses. Despite these differences, OTFT sensors fabricated from H₂TBP and H₂Pc exhibit nearly identical analyte sensitivity and analyte response kinetics. The results suggest that while the interactions between molecules in the solid state determine conductivity, localized interactions between the analyte and the molecular binding site dominate analyte binding and determine sensor response.     

Effect of aluminium doping on structural and gas sensing properties of zinc oxide thin films deposited by spray pyrolysis

A facile spray pyrolysis route is used to deposit aluminium doped ZnO (AZO) thin films on to the glass substrates. It is observed that on aluminium doping the particle size of ZnO reduces significantly; moreover, uniformity of particle also gets enhanced. Their XRD study reveals that intensity ratio of crystal planes depend on the aluminium doping concentration. The gas response studies of; ∼800 nm thick Al-doped ZnO films at different operating temperatures show that 5 at% Al-doped ZnO thin film exhibits highest response towards H₂S gas at 200 °C. The results suggest that the gas response strongly depends on the particle size and aluminium doping in the ZnO.     

Highly sensitive and selective LPG sensor based on α-Fe2O3 nanorods

The α-Fe₂O₃ nanorods were successfully synthesized without any templates by calcining the α-FeOOH precursor in air at 300 °C for 2 h and their LPG sensing characteristics were investigated. The α-FeOOH precursor was prepared through a simple and low cost wet chemical route at low temperature (40 °C) using FeSO₄·7H₂O and CH₃COONa as starting materials. The formation of α-FeOOH precursor and its topotactic transformation to α-Fe₂O₃ upon calcination was confirmed by X-ray diffraction measurement (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis. The α-Fe₂O₃ nanorods exhibited outstanding gas sensing characteristics such as, higher gas response (∼1746-50 ppm LPG at 300 °C), extremely rapid response (∼3-4 s), relatively slow recovery (∼8-9 min), excellent repeatability, good selectivity and lower operating temperature (∼300 °C). Furthermore, the α-Fe₂O₃ nanorods are able to detect up to 5 ppm for LPG with reasonable response (∼15) at the operating temperature of 300 °C and they can be reliably used to monitor the concentration of LPG over the range (5-60 ppm). The experimental results clearly demonstrate the potential of using the α-Fe₂O₃ nanorods as sensing material in the fabrication of LPG sensors. Plausible LP G sensing mechanism of the α-Fe₂O₃ nanorods is also discussed.     

Synthesis and characterisation of nanosized TiO2-ZrO2 binary system prepared by an aqueous sol-gel process: Physical and sensing properties

Nanostructured TiO₂-ZrO₂ thin films and powders were prepared by a straightforward aqueous particulate sol-gel route. Titanium (IV) isopropoxide and zirconium (IV) acetate hydrate were used as precursors, and hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the specific surface area. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy revealed that the powder were crystallised at the low temperature of 500 °C, containing anatase-TiO₂ and tetragonal-ZrO₂ phases. Furthermore, it was found that ZrO₂ retarded the anatase-to-rutile transformation up to 900 °C. The activation energies for crystallite growth of TiO₂ and ZrO₂ components in the binary system were calculated 10.16 and 3.12 kJ/mol, respectively. Transmission electron microscope (TEM) image showed that one of the smallest crystallite sizes was obtained for TiO₂-ZrO₂ binary mixed oxide, being 5 nm at 500 °C. Field emission scanning electron microscope (FESEM) analysis revealed that the deposited thin films had nanostructured morphology with the average grain size of 20 nm at 500 °C and 36 nm at 900 °C. Thin films produced under optimised conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO and NO₂ gases at low operating temperature of 150 °C, resulted in an increase of thermal stability of sensing films as well as a decrease in the power consumption. Furthermore, calibration curves revealed that TiO₂-ZrO₂ sensor follows the power law, S = A[gas]^B (where S is sensor response, coefficients A and B are constants and [gas] is gas concentration) for the two types of gases, and it has excellent capability for the detection of low gas concentrations.