The Properties of Sintered Calcium Phosphate with [Ca]/[P] = 1.50

In order to obtain the properties of the sintered as-dried calcium phosphate with [Ca]/[P] = 1.50, the characteristics of sintered pellets have been investigated using X-ray diffraction (XRD), inductively coupled plasma-mass spectrometry (ICP-MS), Fourier-transform infrared (FT-IR) spectra, Vickers hardness indentation and scanning electron microscopy (SEM). When the pellet samples were sintered between 700 °C and 1200 °C for 4 h, the hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, HA) still maintained the major phase, accompanied with the rhenanite (NaCaPO₄) as the secondary phase and β-tricalcium phosphate (β-Ca₃(PO₄)₂, β-TCP) as the minor phases. In addition, the HA partially transformed to α-tricalcium phosphate (α-Ca₃(PO₄)₂, α-TCP) and tetracalcium phosphate (Ca₄(PO4)₂O, TTCP), when the pellet samples were sintered at 1300 °C and 1400 °C, respectively, for 4 h. The maximum density and Vickers Hardness (HV) of sintered pellet samples were 2.85 g/cm³ (90.18% theoretical density (T.D.)) and 407, which appeared at 1200 °C and 900 °C, respectively.     

Purification and Characterization of a Ginsenoside Rb1-Hydrolyzing ��-Glucosidase from Aspergillus niger KCCM 11239

Rb₁-hydrolyzing β-glucosidase from Aspergillus niger KCCM 11239 was studied to develop a bioconversion process for minor ginsenosides. The specific activity of the purified enzyme was 46.5 times greater than that of the crude enzyme. The molecular weight of the native enzyme was estimated to be approximately 123 kDa. The optimal pH of the purified enzyme was pH 4.0, and the enzyme proved highly stable over a pH range of 5.0–10.0. The optimal temperature was 70 °C, and the enzyme became unstable at temperatures above 60 °C. The enzyme was inhibited by Cu²⁺, Mg²⁺, Co²⁺, and acetic acid (10 mM). In the specificity tests, the enzyme was found to be active against ginsenoside Rb₁, but showed very low levels of activity against Rb₂, Rc, Rd, Re, and Rg₁. The enzyme hydrolyzed the 20-C,β-(1→6)-glucoside of ginsenoside Rb₁ to generate ginsenoside Rd and Rg₃, and hydrolyzed 3-C,β-(1→2)-glucoside to generate F₂. The properties of the enzyme indicate that it could be a useful tool in biotransformation applications in the ginseng industry, as well as in the development of novel drug compounds.     

Phase Transformations of α-Alumina Made from Waste Aluminum via a Precipitation Technique

We report on a recycling project in which α-Al₂O₃ was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H₂SO₄ solution to form an Al₂(SO₄)₃ solution. The Al₂(SO₄)₃ salt was contained in a white semi-liquid solution with excess H₂SO₄; some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al₂(SO₄)₃·18H₂O. The Al₂(SO₄)₃·18H₂O was calcined in an electrical furnace for 3 h at temperatures of 400–1400 °C. The heating and cooling rates were 10 °C/min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al₂(SO₄)₃·18H₂O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al₂O₃ at high temperatures. The X-ray diffraction results indicated that the α-Al₂O₃ phase was realized when the calcination temperature was at 1200 °C or higher.     

Synthesis of pure aragonite by sonochemical mineral carbonation

The objective of this work was to promote the formation of the aragonite polymorph of calcium carbonate, which has some valuable applications in industry, via the mineral carbonation route. The combination of ultrasound with magnesium ions promoted the formation of pure aragonite crystals at optimum conditions. It was possible to synthesize high purity aragonite precipitates at temperatures ranging from 24 °C to 70 °C, with the resulting powders possessing varying particle size distributions (from sub-micron up to 20 μm) and crystal morphologies (from acicular needles to novel hubbard squash-like particles). Several process parameters were found to influence the produced calcium carbonate polymorph ratios (aragonite over calcite). Higher values of magnesium-to-calcium ratio, intermediate ultrasound amplitude (60%), continuous ultrasound application (100% cycle), introduction of ultrasound pre-breakage, lowering of the CO₂ flow rate, and increase in the relative concentration (g/L Ca(OH)₂), all promoted aragonite formation. A potential route for industrial production of this material has been identified via a fed-batch process, which effectively reutilizes magnesium chloride while maintaining high aragonite yield. The results presented herein are significantly superior to aragonite formation using only single promoting techniques, typically found in literature, and go beyond by focusing on pure (>99%) aragonite formation.     

The Effect of Long-Term Storage on the Physiochemical and Bactericidal Properties of Electrochemically Activated Solutions

Electrochemically activated solutions (ECAS) are generated by electrolysis of NaCl solutions, and demonstrate broad spectrum antimicrobial activity and high environmental compatibility. The biocidal efficacy of ECAS at the point of production is widely reported in the literature, as are its credentials as a “green biocide.” Acidic ECAS are considered most effective as biocides at the point of production and ill suited for extended storage. Acidic ECAS samples were stored at 4 °C and 20 °C in glass and polystyrene containers for 398 days, and tested for free chlorine, pH, ORP and bactericidal activity throughout. ORP and free chlorine (mg/L) in stored ECAS declined over time, declining at the fastest rate when stored at 20 °C in polystyrene and at the slowest rate when stored at 4 °C in glass. Bactericidal efficacy was also affected by storage and ECAS failed to produce a 5 log₁₀ reduction on five occasions when stored at 20 °C. pH remained stable throughout the storage period. This study represents the longest storage evaluation of the physiochemical parameters and bactericidal efficacy of acidic ECAS within the published literature and reveals that acidic ECAS retain useful bactericidal activity for in excess of 12 months, widening potential applications.     

Synthesis, magnetic and optical properties of core/shell Co1-xZnxFe2O4/SiO2 nanoparticles

The optical properties of multi-functionalized cobalt ferrite (CoFe₂O₄), cobalt zinc ferrite (Co_0.5Zn_0.5Fe₂O₄), and zinc ferrite (ZnFe₂O₄) nanoparticles have been enhanced by coating them with silica shell using a modified Stöber method. The ferrites nanoparticles were prepared by a modified citrate gel technique. These core/shell ferrites nanoparticles have been fired at temperatures: 400°C, 600°C and 800°C, respectively, for 2 h. The composition, phase, and morphology of the prepared core/shell ferrites nanoparticles were determined by X-ray diffraction and transmission electron microscopy, respectively. The diffuse reflectance and magnetic properties of the core/shell ferrites nanoparticles at room temperature were investigated using UV/VIS double-beam spectrophotometer and vibrating sample magnetometer, respectively. It was found that, by increasing the firing temperature from 400°C to 800°C, the average crystallite size of the core/shell ferrites nanoparticles increases. The cobalt ferrite nanoparticles fired at temperature 800°C; show the highest saturation magnetization while the zinc ferrite nanoparticles coated with silica shell shows the highest diffuse reflectance. On the other hand, core/shell zinc ferrite/silica nanoparticles fired at 400°C show a ferromagnetic behavior and high diffuse reflectance when compared with all the uncoated or coated ferrites nanoparticles. These characteristics of core/shell zinc ferrite/silica nanostructures make them promising candidates for magneto-optical nanodevice applications.     

Optimization of Supercritical CO2 Extraction of Fish Oil from Viscera of African Catfish (Clarias gariepinus)

Fish oil was extracted from the viscera of African Catfish using supercritical carbon dioxide (SC-CO₂). A Central Composite Design of Response Surface methodology (RSM) was employed to optimize the SC-CO₂ extraction parameters. The oil yield (Y) as response variable was executed against the four independent variables, namely pressure, temperature, flow rate and soaking time. The oil yield varied with the linear, quadratic and interaction of pressure, temperature, flow rate and soaking time. Optimum points were observed within the variables of temperature from 35 °C to 80 °C, pressure from 10 MPa to 40 MPa, flow rate from 1 mL/min to 3 mL/min and soaking time from 1 h to 4 h. However, the extraction parameters were found to be optimized at temperature 57.5 °C, pressure 40 MPa, flow rate 2.0 mL/min and soaking time 2.5 h. At this optimized condition, the highest oil yields were found to be 67.0% (g oil/100 g sample on dry basis) in the viscera of catfish which was reasonable to the yields of 78.0% extracted using the Soxhlet method.     

Optimization of β-Glucosidase, β-Xylosidase and Xylanase Production by Colletotrichum graminicola under Solid-State Fermentation and Application in Raw Sugarcane Trash Saccharification

Efficient, low-cost enzymatic hydrolysis of lignocellulosic residues is essential for cost-effective production of bioethanol. The production of β-glucosidase, β-xylosidase and xylanase by Colletotrichum graminicola was optimized using Response Surface Methodology (RSM). Maximal production occurred in wheat bran. Sugarcane trash, peanut hulls and corncob enhanced β-glucosidase, β-xylosidase and xylanase production, respectively. Maximal levels after optimization reached 159.3 ± 12.7 U g⁻¹, 128.1 ± 6.4 U g⁻¹ and 378.1 ± 23.3 U g⁻¹, respectively, but the enzymes were produced simultaneously at good levels under culture conditions optimized for each one of them. Optima of pH and temperature were 5.0 and 65 °C for the three enzymes, which maintained full activity for 72 h at 50 °C and for 120 min at 60 °C (β-glucosidase) or 65 °C (β-xylosidase and xylanase). Mixed with Trichoderma reesei cellulases, C. graminicola crude extract hydrolyzed raw sugarcane trash with glucose yield of 33.1% after 48 h, demonstrating good potential to compose efficient cocktails for lignocellulosic materials hydrolysis.     

Synthesis, Structure of Nitrogen-Containing Phosphinogold(I) Ferrocenes. In vitro Activity against Bladder and Colon Carcinoma Cell Lines

The gold salt [(tht)AuCl] was reacted with [1-N,N-dimethylaminométhyl-2-diphenylphosphino]ferrocene (1) forming the bimetallic derivative 4. The reaction of methyl iodide and tetramethylammonium bromide on the chloride 4 produced the ammonium salt 5 and the bromide 6 respectively. New aminophosphines 2 and 3, which represent two of the rare phosphorylated metallocenes containing P(III)-N bond have also been coordinated to gold(I) to form 7 and 8. The presence of the ethoxy group in 7 provides evidence for the lability of one nitrogen-phosphorus bond. The X-ray structure of compounds 4 and 7 have been established. Both crystallize in space group P2₁/c, monoclinic, with a = 11.095(2) Å, b = 12.030(3) Å, c = 17.763(4) Å, β= 94.02(2)∘, Z = 4 for 4 and a = 14.863(3) Å, b = 8.036(5)Å, c = 18.062(5)Å, β =101.64(1)°, Z = 4 for 7. ¹⁹⁷Au Mössbauer data are in good agreement with those for other linear P-Au-Cl containing complexes. The compounds were evaluated for in vitro anti-tumour activity against two human tumours. Differential cytotoxicity was observed with activity comparable to cisplatin, with the exception of one compound which was significantly more cytotoxic.     

Lower Temperature Cultures Enlarge the Effects of Vitreoscilla Hemoglobin Expression on Recombinant Pichia pastoris

An heterologous expression of Vitreoscilla hemoglobin (VHb) for improving cell growth and recombinant protein production has been successfully demonstrated in various hosts, including Pichia pastoris. Lower temperature cultures can enhance target protein production in some studies of P. pastoris. In this study, the strategy of combining heterologous VHb expression and lower temperature cultures in P. pastoris showed that final cell density and viability of VHb⁺ strain at 23 °C were higher than that at 30 °C. In addition, the effects of VHb expression on recombinant β-galactosidase production and oxygen uptake rate were also higher at 23 °C than at 30 °C. Consequently, lower temperature cultures can enlarge VHb effectiveness on cell performance of P. pastoris. This is because VHb activity obtained at 23 °C cultures was twofold higher than that at 30 °C cultures, due to a different heme production. This strategy makes P. pastoris an excellent expression host particularly suitable for increasing the yields of the low-stability and aggregation-prone recombinant proteins.     

Factors affecting the phase and morphology of CaCO3 prepared by a bubbling method

Precipitated calcium carbonate (PCC) was prepared by bubbling a CO₂/N₂ mixed gas into a CaCl₂ solution. The influence of preparation conditions on the phase and morphology of PCC was discussed with the help of XRD and SEM measurements. The results showed that the initial CaCl₂ concentration, flow rate and temperature play an important role on the morphology of PCC. At low initial CaCl₂ concentration or high flow rate, spherical vaterite was preferably formed. Otherwise, the rhombic calcite was ready to form. Temperature is a determining factor on the formation of aragonite. Needle-like aragonite was precipitated at 60 °C. The results also indicated that both the bubbling time and stirring rate have a minor effect on the phase and morphology of PCC.     

Facile Synthesis of Calcium Borate Nanoparticles and the Annealing Effect on Their Structure and Size

Calcium borate nanoparticles have been synthesized by a thermal treatment method via facile co-precipitation. Differences of annealing temperature and annealing time and their effects on crystal structure, particle size, size distribution and thermal stability of nanoparticles were investigated. The formation of calcium borate compound was characterized by X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FTIR), Transmission electron microscopy (TEM), and Thermogravimetry (TGA). The XRD patterns revealed that the co-precipitated samples annealed at 700 °C for 3 h annealing time formed an amorphous structure and the transformation into a crystalline structure only occurred after 5 h annealing time. It was found that the samples annealed at 900 °C are mostly metaborate (CaB₂O₄) nanoparticles and tetraborate (CaB₄O₇) nanoparticles only observed at 970 °C, which was confirmed by FTIR. The TEM images indicated that with increasing the annealing time and temperature, the average particle size increases. TGA analysis confirmed the thermal stability of the annealed samples at higher temperatures.     

The effects of atmosphere and calcined temperature on photocatalytic activity of TiO2 nanofibers prepared by electrospinning

TiO₂-based nanofibers were synthesized using a sol–gel method and electrospinning technique. The as-spun composite fibers were heat-treated at different temperatures (500°C, 550°C, 600°C, and 650°C) and atmospheres (ammonia and nitrogen) for 4 h. The fibers had diameters of 50 to 200 nm and mainly featured anatase and rutile phases. The anatase phase decreased and the rutile phase increased with increasing temperature. Different nitrogen conditions exerted minimal effects on the TiO₂ crystalline phase. Different nitriding atmospheres during preservation heating yielded various effects on fibers. The effect of nitrogen in ammonia atmosphere is better than that in nitrogen atmosphere. The fibers heat-treated at 600°C and subjected to preservation heating in NH₃ showed high photocatalytic activity.     

Stabilized Conversion Efficiency and Dye-Sensitized Solar Cells from Beta vulgaris Pigment

Dye-Sensitized Solar Cells (DSSCs), based on TiO₂ and assembled using a dye from Beta vulgaris extract (BVE) with Tetraethylorthosilicate (TEOS), are reported. The dye BVE/TEOS increased its UV resistance, rendering an increase in the cell lifetime; the performance of these solar cells was compared to those prepared with BVE without TEOS. The efficiency η for the solar energy conversion was, for BVE and BVE/TEOS, of 0.89% ± 0.006% and 0.68% ± 0.006% with a current density Jsc of 2.71 ± 0.003 mA/cm² and 2.08 ± 0.003 mA/cm², respectively, using in both cases an irradiation of 100 mW/cm² at 25 °C. The efficiency of the BVE solar cell dropped from 0.9 ± 0.006 to 0.85 ± 0.006 after 72 h of operation, whereas for the BVE/TEOS, the efficiency remained practically constant in the same period of time.     

Fractionation of whey protein isolate with supercritical carbon dioxide-process modeling and cost estimation

An economical and environmentally friendly whey protein fractionation process was developed using supercritical carbon dioxide (sCO₂) as an acid to produce enriched fractions of α-lactalbumin (α-LA) and β-lactoglobulin (β-LG) from a commercial whey protein isolate (WPI) containing 20% α-LA and 55% β-LG, through selective precipitation of α-LA. Pilot-scale experiments were performed around the optimal parameter range (T = 60 to 65 °C, P = 8 to 31 MPa, C = 5 to 15% (w/w) WPI) to quantify the recovery rates of the individual proteins and the compositions of both fractions as a function of processing conditions. Mass balances were calculated in a process flow-sheet to design a large-scale, semi-continuous process model using SuperproDesigner® software. Total startup and production costs were estimated as a function of processing parameters, product yield and purity. Temperature, T, pressure, P, and concentration, C, showed conflicting effects on equipment costs and the individual precipitation rates of the two proteins, affecting the quantity, quality, and production cost of the fractions considerably. The highest α-LA purity, 61%, with 80% α-LA recovery in the solid fraction, was obtained at T = 60 °C, C = 5% WPI, P = 8.3 MPa, with a production cost of $8.65 per kilogram of WPI treated. The most profitable conditions resulted in 57%-pure α-LA, with 71% α-LA recovery in the solid fraction and 89% β-LG recovery in the soluble fraction, and production cost of $5.43 per kilogram of WPI treated at T = 62 °C, C = 10% WPI and P = 5.5 MPa. The two fractions are ready-to-use, new food ingredients with a pH of 6.7 and contain no residual acid or chemical contaminants.     

Muscodor albus Volatiles Control Toxigenic Fungi under Controlled Atmosphere (CA) Storage Conditions

Muscodor albus, a biofumigant fungus, has the potential to control post-harvest pathogens in storage. It has been shown to produce over 20 volatile compounds with fungicidal, bactericidal and insecticidal properties. However, M. albus is a warm climate endophyte, and its biofumigant activity is significantly inhibited at temperatures below 5 °C. Conidia of seven mycotoxin producing fungi, Aspergillus carbonarius, A. flavus, A. niger, A. ochraceus, Penicillium verrucosum, Fusarium culmorum and F. graminearum, were killed or prevented from germinating by exposure to volatiles from 2 g M. albus-colonized rye grain per L of headspace in sealed glass jars for 24 h at 20 °C. Two major volatiles of M. albus, isobutyric acid (IBA) and 2-methyl-1-butanol (2MB) at 50 μL/L and 100 μL/L, respectively, gave differential control of the seven fungi when applied individually at 20 °C. When the fungi were exposed to both IBA and 2MB together, an average of 94% of the conidia were killed or suppressed. In a factorial experiment with controlled atmosphere storage (CA) at 3 °C and 72 h exposure to four concentrations of IBA and 2MB combinations, 50 μL/L IBA plus 100 μL/L 2MB killed or suppressed germination of the conidia of all seven fungi. Controlled atmosphere had no significant effect on conidial viability or volatile efficacy. Major volatiles of M. albus may have significant potential to control plant pathogens in either ambient air or CA storage at temperatures below 5 °C. However, combinations of volatiles may be required to provide a broader spectrum of control than individual volatiles.     

3D Structure Elucidation of Thermostable L2 Lipase from Thermophilic Bacillus sp. L2

The crystallization of proteins makes it possible to determine their structure by X-ray crystallography, and is therefore important for the analysis of protein structure-function relationships. L2 lipase was crystallized by using the J-tube counter diffusion method. A crystallization consisting of 20% PEG 6000, 50 mM MES pH 6.5 and 50 mM NaCl was found to be the best condition to produce crystals with good shape and size (0.5 × 0.1 × 0.2 mm). The protein concentration used for the crystallization was 3 mg/mL. L2 lipase crystal has two crystal forms, Shape 1 and Shape 2. Shape 2 L2 lipase crystal was diffracted at 1.5 Å and the crystal belongs to the orthorhombic space group P2₁2₁2₁, with unit-cell parameters a = 72.0, b = 81.8, c = 83.4 Å, α = β = γ = 90°. There is one molecule per asymmetric unit and the solvent content of the crystals is 56.9%, with a Matthew’s coefficient of 2.85 Å Da⁻¹. The 3D structure of L2 lipase revealed topological organization of α/β-hydrolase fold consisting of 11 β-strands and 13 α-helices. Ser-113, His-358 and Asp-317 were assigned as catalytic triad residues. One Ca²⁺ and one Zn²⁺ were found in the L2 lipase molecule.     

Overcoming the Recalcitrance for the Conversion of Kenaf Pulp to Glucose via Microwave-Assisted Pre-Treatment Processes

This study evaluates the pre-treatment of cellulose from kenaf plant to yield sugar precursors for the production of ethanol or butanol for use as biofuel additives. In order to convert the crystalline cellulosic form to the amorphous form that can undergo enzymatic hydrolysis of the glycosidic bond to yield sugars, kenaf pulp samples were subjected to two different pre-treatment processes. In the acid pre-treatment, the pulp samples were treated with 37.5% hydrochloric acid in the presence of FeCl₃ at 50 °C or 90 °C whereas in the alkaline method, the pulp samples were treated with 25% sodium hydroxide at room temperature and with 2% or 5% sodium hydroxide at 50 °C. Microwave-assisted NaOH-treatment of the cellulose was also investigated and demonstrated to be capable of producing high glucose yield without adverse environmental impact by circumventing the use of large amounts of concentrated acids i.e., 83–85% phosphoric acid employed in most digestion processes. The treated samples were digested with the cellulase enzyme from Trichoderma reesei. The amount of glucose produced was quantified using the Quantichrom^™ glucose bioassay for assessing the efficiency of glucose production for each of the treatment processes. The microwave-assisted alkaline pre-treatment processes conducted at 50 °C were found to be the most effective in the conversion of the crystalline cellulose to the amorphous form based on the significantly higher yields of sugar produced by enzymatic hydrolysis compared to the untreated sample.     

Enzymatic Reactions in Near Critical CO2: The Effect of Pressure on Phenol Removal by Tyrosinase

The use of enzymes in supercritical CO₂ (SCCO₂) has received extensive attention in recent years. Biocatalysts have the advantage of substrate specificity and SCCO₂ offers several advantages over liquid solvents. This work deals with the utilization of SCCO₂ as a medium for the enzymatic removal of phenol from aqueous solutions using tyrosinase. Since the presence of oxygen is crucial for the enzyme-catalyzed oxidation, the substantial solvating power of SCCO₂ makes it a promising medium for such reactions. The conversion of phenol was higher at 10 MPa. Under near critical conditions (7 MPa, 35 °C), the addition of air at 5 × 10⁵ Pa of pressure improved phenol removal.