共查询到19条相似文献,搜索用时 187 毫秒
1.
2.
锥形转子永磁电机具有与普通永磁电机不同的结构特点,电机的分析计算有其特殊性,以简化方法计算容易得出误差较大的结果.以三维有限元法分析了不同结构参数下锥形转子永磁电机的磁场分布,结果表明其磁场沿轴向分布比较均匀,并且气隙磁场随着转子轴向位移的增大线性降低.在此基础上,分析了锥角,转子轴向位移,永磁体形状等结构参数对交直轴电感、转矩等的影响,结果表明交直轴电感参数在不同的永磁体形状下随着转子轴向位移有着不同的变化趋势,锥角影响着交直轴电感的变化幅度,转矩随着转子轴向位移的增大而减小.同时计算分析的正确性通过样机实测值得到了验证. 相似文献
3.
4.
永磁辅助同步磁阻电机良好的运行特性与电机的电感参数密切相关,在电磁方案设计阶段需要对电感参数进行准确计算。介绍了等效交直轴法、静态场法、瞬态场法和冻结磁导率法计算交直轴电感参数的原理,并采用上述四种方法进行了电机交直轴电感参数的仿真计算。进行样机试制,并采用伏安法测试了样机电感参数,将仿真结果与测试结果进行对比,以验证各方法的准确性。结果表明,冻结磁导率法仿真得到的交直轴电感参数与实测结果的误差在3〖WTB4〗%〖WTBZ〗以内,采用冻结磁导率法的计算结果更为准确。 相似文献
5.
考虑参数变化的永磁同步电动机弱磁控制研究 总被引:2,自引:0,他引:2
永磁同步电动机的弱磁控制是通过增加定子直轴负向电流,利用直轴电枢反应使电机气隙磁场减弱,达到等效于减弱合成磁场的效果以实现弱磁增速的目的,这就造成弱磁运行时,转速越高对应的直轴负向电流越大,即电枢反应越严重.直轴电枢反应严重影响着直轴同步电感,同时交轴电流也在一个较大的范围内变化,交轴电流的变化也影响着交轴同步电感和永磁体产生的磁链.当电机参数在运行过程中发生较大变化时,便造成了转矩给定值和实际系统的转矩输出能力之间存在一定的偏差,使得系统无法跟踪指令值,导致整个系统性能下降.当电机参数发生变化时,为了提高系统的控制性能,本文提出了转矩模糊控制器,从而使给定转矩较好的跟踪电机实际转矩输出能力. 相似文献
6.
7.
8.
考虑磁路交叉饱和的内置式永磁同步电动机调速控制 总被引:1,自引:0,他引:1
内置式永磁同步电动机由于在结构上气隙小,交直轴电感参数差异大,因此其控制性能受参数影响敏感.由于内置式永磁同步电动机的这个特点,它在其整个控制区域,即恒转矩区域和弱磁运行区域,都必须要考虑磁路交叉饱和对电机参数的影响.文章建立了考虑交叉饱和的永磁同步电动机暂态有限元模型,通过有限元模型和修正的电感计算方法对考虑交叉饱和情况下的电机d轴和q轴电感进行了分析计算.并利用有限元模型对电机最佳电流控制角、输出转矩及弱磁控制性能等进行分析.最后用求得的电感参数用于控制并与直接采用有限元方法的分析结果进行比较验证,实验结果表明两者完全吻合. 相似文献
9.
考虑交叉饱和影响的永磁同步电机稳态参数有限元分析 总被引:5,自引:0,他引:5
针对永磁电机相关控制策略及性能计算均需要准确地得到电感和磁链等稳态参数,而它们又受交叉饱和效应影响严重,常规方法无法准确计算的问题,以有限元为工具,分析了计算永磁磁链和直轴、交轴电枢反应电感的不同方法。研究了交叉饱和效应对永磁电机的直轴、交轴电枢反应电感的影响,提出由于交叉饱和效应导致的直轴交轴存在互感,以及直轴上的永磁磁势产生交轴磁通的问题。采用冻结单元磁导率的方法,将非线性场线性化,计算得到了稳态参数随直轴、交轴电流变化的趋势。通过对比,使用计算得到的稳态参数仿真结果和实际测试结果,在空载与负载条件下的吻合很好,证明了使用冻结磁导率法计算参数是可靠的。 相似文献
10.
分数槽集中绕组嵌入式永磁同步电机设计 总被引:1,自引:0,他引:1
分析了一类极槽数相近的分数槽集中绕组嵌入式永磁同步(FCW—IPM)电机的极槽数配合选择依据,基于二维有限元法对该类电机的气隙磁场分布、反电动势、稳态转矩、定位力矩等电磁特性进行了计算和分析。提出了一种交直轴电流全解耦与冻结磁导率相结合的方法,详细分析了交叉耦合及定转子相对位置变化对电机交直轴电感的影响规律。设计并制造了一台额定功率为10kW的样机,样机实验结果验证了设计方法和理论分析的正确性,为该类电机在混合动力汽车驱动领域的进一步应用奠定了基础。 相似文献
11.
永磁同步电机具有较高的效率和功率密度,在电动汽车驱动系统中广泛应用。电机的d、q轴电感是设计控制系统的重要参数,但重载情况下受磁饱和及交叉饱和影响严重。传统控制技术忽略磁饱和效应,导致转矩控制的精确性不足。采用有限元法分析电机负载时的磁饱和情况,计算考虑磁饱和及交叉饱和的d、q轴电感参数。以此为基础,拟合d、q轴电感和电流关系。设计计及磁饱和的最大转矩电流比MTPA(maximum torque per ampere)控制,使d、q轴参考电流计算中使用的电感随电机电流变化。通过对比,证明计及磁饱和的MTPA控制能够实现输出转矩的精确控制,提高永磁同步电机的动态响应性能。 相似文献
12.
The influence of the stator iron loss cannot be neglected since the high-speed operation and precision torque control of AC motors are required. This paper presents the modeling and vector control of synchronous reluctance motors including the stator iron loss. The stator iron loss is modeled by additional windings on the d-q axes, and is introduced as an equivalent iron loss resistance in voltage equations under the assumption that the losses in the stator core are produced in equivalent eddy current windings on d-q axes. The equivalent iron loss resistance is inserted in series with exciting inductance, and the d and q axes interfere with each other through the equivalent iron loss resistance. To achieve vector control, the d-q axis currents are decoupled by nonlinear control voltages. As a result, the instantaneous torque control scheme is equal to that of a DC machine and the torque control is simplified 相似文献
13.
交流永磁同步电机的模型参数辨识精度是影响电机矢量控制方法性能的关键.基于此,在交流永磁同步电机同步旋转坐标系的数学模型下,提出了一种交流永磁同步电机模型参数的辨识方法,采用直轴电流阶跃响应实验同时辨识定子电阻和直轴电感,脉冲电压实验检测交轴电感,速度驱动实验检测转子磁通.在电机模型参数辨识结果的基础上,讨论了基于矢量控制的交流永磁同步电机调速控制系统电流环和速度环的设计方法.在基于TMS320F2812 DSP的电力机车粘着控制实验平台上进行了实验研究.实验结果表明电机模型参数辨识方法的有效性,调速系统具有良好的动态和稳态性能. 相似文献
14.
该文对永磁无刷直流电机电感参数的计算和测定方法进行了推导,通过坐标变换,把三相电机ABC坐标系下的自感、互感的复杂计算和测定问题转换为d-q坐标系下简单的计算和测定问题。该方法通过测定一周转子不同位置下的电压、电流、功率数据,可直接计算出电机的直轴电感和交轴电感。采用该方法分析了转子位置、电流、频率、温度对电感参数的影响。 相似文献
15.
本文研究电感不对称对双绕组永磁同步电机基于脉振高频电压注入法的无位置传感器控制的影响。基于Ansoft/Maxwell建立有限元仿真模型,分析双绕组永磁同步电机两种工况下的电感波形。仿真结果表明由于绕组结构的非对称性,单个子电机工况下三相电感不再对称,d-q轴电感产生较大波动。理论推导了非恒值d-q轴电感条件下脉振高频电压注入法的数学模型,证明了该方法对电感波形有较高要求。通过Simulink搭建仿真模型,研究电感不对称对双绕组永磁同步电机高频注入法控制的影响,并且dSPACE实验平台上进行验证。仿真和实验结果表明,两个子电机同时运行工况下,基于脉振高频电压注入法的无位置传感器控制可以正常运行;但在单个子电机运行工况下,由于d-q轴电感存在较大波动,PLL锁相环并不能有效跟踪转子位置,导致无位置传感器控制无法正常起动。 相似文献
16.
Mohamed M. Saied 《电力部件与系统》2013,41(8):677-687
This paper presents a method for increasing the daily output mechanical energy supplied by DC motors directly connected to solar cell arrays (SCA). Without any interfacing circuitry between the PV-array and the DC series motor, an increase of about 10% in the mechanical energy can be achieved. The procedure is based on the use of series DC motors with nonlinear magnetic circuits so that these motors will be driven into their saturation region during their normal operation. It will be shown that through properly selecting the parameters of the motor’s magnetization characteristics (initial mutual inductance and the flux saturation level), an improved matching between the PV-array and the DC motor will be possible. 相似文献
17.
18.
提出一种自抗扰磁链观测器,它对永磁同步电动机电感和永磁磁链的变化具有很好的鲁棒性.永磁同步电动机由电流调节逆变器来驱动,其中d-q轴电流是由两个前馈交叉耦合的比例积分控制器来解耦调节.电流调节器反映磁链偏差的积分项用来补偿由于电机工作温度变化等原因带来的电感和永磁磁链变化.实验结果表明了该观测器的有效性和优越性. 相似文献
19.
A method to determine direct‐ and quadrature‐axis inductances of permanent magnet synchronous motors
Shu Yamamoto Takashi Kano Yoshihiro Yamaguchi Takahiro Ara 《Electrical Engineering in Japan》2010,171(3):41-50
The equivalent circuit constants of permanent magnet synchronous motors are needed in the calculation of operation characteristics, construction of a control system, etc. These constants can be computed from the data on structural form and materials. However, measurements are necessary to obtain highly precise values. Methods for measurement of the d‐ and q‐axis inductances can be roughly divided into rotational and standstill methods. The standstill methods have the advantage that they are easy to carry out. However, it is difficult to consider magnetic saturation and distortion of the change in the armature winding inductance. The accuracy of the standstill method can be improved if these effects can be readily taken into account. This paper describes a standstill method for measuring accurate d‐ and q‐axis synchronous inductances of permanent magnet synchronous motors. By utilizing the fact that the EMF interference terms in the motor voltage equation considering the distortion of the inductance change are equal to zero when the rotor is in a specific position, the proposed method determines the inductances considering both magnetic saturation and inductance distortion effects from simple off‐line standstill testing. In addition, this method is capable of taking cross‐magnetic saturation into account when used with the necessary testing equipment. The proposed method was implemented on a 0.4‐kW interior permanent magnet synchronous motor with concentrated stator winding. The validity of the proposed method was demonstrated by comparing the measured and calculated results of the no‐load and on‐load characteristics. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 171(3): 41–50, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20969 相似文献