瓶状和棒形的纳米ZnO光催化降解甲基橙的研究

以硝酸锌,醋酸钠为原料,聚乙二醇-10000为表面活性剂,采用溶剂热法合成了瓶状和棒形的纳米ZnO,并用X射线衍射仪(XRD)、透射电镜(TEM)、紫外-可见分光光度计时其进行了表征,结果显示合成的纳米ZnO属于六方纤锌矿的晶体结构,对200～380nm波长范围的紫外光有较强的吸收性能.并以纳米ZnO作为光催化剂对甲基橙进行了光降解实验,研究了催化剂用量、甲基橙初始浓度及电解质(SO2-4、Cl-)等对甲基橙降解率的影响.     

FeVO_4光催化剂降解甲基橙研究

实验采用液相沉淀法制备了三斜型FeVO4光催化剂,采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)等方法对样品结构和形貌进行分析和表征,在40W紫外灯(主波长为253.7nm)照射下降解一定浓度的甲基橙溶液,研究其对甲基橙溶液降解效果.研究了催化剂用量、甲基橙初始浓度、光强度及pH值对甲基橙降解率的影响.     

Photocatalytic degradation of methyl orange using biologically enhanced tin oxide nanoparticles under UV-irradiation

Tin oxide nanoparticles (size?=?14 nm) have been prepared using DNA, a biological molecule, by co-precipitation method. The SnO₂ catalysts were characterized by X-ray diffraction, scanning electron microscope, transmission electron spectroscopy, fourier transform infra-red spectroscopy, photoluminescence spectroscopy and UV–Vis spectroscopy. The photocatalytic properties of SnO₂ nanoparticles were investigated via methyl orange as a model organic compound under UV light irradiation. The study proves SnO₂ as an efficient catalyst in removing organic pollutants in water.     

Photocatalytic paper using zinc oxide nanorods

Zinc oxide (ZnO) nanorods were grown on a paper support prepared from soft wood pulp. The photocatalytic activity of a sheet of paper with ZnO nanorods embedded in its porous matrix has been studied. ZnO nanorods were firmly attached to cellulose fibers and the photocatalytic paper samples were reused several times with nominal decrease in efficiency. Photodegradation of up to 93% was observed for methylene blue in the presence of paper filled with ZnO nanorods upon irradiation with visible light at 963 Wm^–2 for 120 min. Under similar conditions, photodegradation of approximately 35% was observed for methyl orange. Antibacterial tests revealed that the photocatalytic paper inhibits the growth of Escherichia coli under room lighting conditions.     

Photocatalytic paper using zinc oxide nanorods

Abstract

Zinc oxide (ZnO) nanorods were grown on a paper support prepared from soft wood pulp. The photocatalytic activity of a sheet of paper with ZnO nanorods embedded in its porous matrix has been studied. ZnO nanorods were firmly attached to cellulose fibers and the photocatalytic paper samples were reused several times with nominal decrease in efficiency. Photodegradation of up to 93% was observed for methylene blue in the presence of paper filled with ZnO nanorods upon irradiation with visible light at 963 Wm^–2 for 120 min. Under similar conditions, photodegradation of approximately 35% was observed for methyl orange. Antibacterial tests revealed that the photocatalytic paper inhibits the growth of Escherichia coli under room lighting conditions.     

壳聚糖-CdS复合纳米粒子对甲基橙的光催化降解作用

用反相微乳液法制备了壳聚糖-CdS复合纳米粒子,并考察了复合纳米粒子用量、光照条件和溶液pH值等因素对光催化降解甲基橙的影响.结果表明:在100 mL质量浓度为20 mg/L的甲基橙溶液中加入0.30 g复合纳米粒子,可以达到较好的光催化降解效果;甲基橙在光催化降解过程中最大吸收波长464 nm处的吸收峰迅速减弱,并最终消失,且在258 nm和455 nm处出现了新的吸收峰,说明甲基橙发生了降解;溶液pH值对光催化降解甲基橙有一定的影响,在弱酸性条件下降解效率较高;复合纳米粒子比普通CdS降解效率高,2 min时高出50%,400 min时高出21.3%.初步提出了复合纳米粒子光催化降解机理,复合纳米粒子的吸附作用是光催化降解作用的前置步骤.     

Photocatalytic degradation of methyl orange using a TiO2/Ti mesh electrode with 3D nanotube arrays

To further improve the photocatalytic techniques for water purification and wastewater treatment, we successfully prepared a new type of TiO(2)/Ti mesh photoelectrode, by anodization in ethylene glycol solution. The three-dimensional arrays of nanotubes formed on Ti mesh show a significant improvement in photocatalytic activity, compared to the nanotube arrays formed on foil. This can be demonstrated by about 22 and 38% enhancement in the degradation efficiency per mass and per area, respectively, when TiO(2)/Ti mesh electrode was used to photocatalyze methyl orange (MO). Furthermore, the effects of different parameters on MO photodegradation were investigated, such as different photoelectrode calcination temperature, the initial pH value of MO solution, and the present of hydrogen peroxide. The superior photocatalytic activity could be achieved by the TiO(2)/Ti mesh photoelectrode calcinated at 550 °C, due to the appearance of mixed crystal phases of anatase and rutile. In strong acidic or caustic conditions, such as pH 1 or 13, a high degradation efficiency can be both obtained. The presence of H(2)O(2) in photocatalytic reactions can promote photocatalytic degradation efficiencies. Moreover, the experimental results demonstrated the excellent stability and reliability of the TiO(2)/Ti mesh electrode.     

纳米La-TiO2光催化降解甲基橙废水的研究

采用溶胶-凝胶法制备了纯TiO2和La掺杂TiO2复合纳米粉体,通过XRD,UV-Vis等测试手段分析了在紫外光照射下,以降解甲基橙为探针反应研究其可见光催化性能。结果显示样品均为锐钛矿相纳米TiO2,稀土元素镧掺杂后纳米TiO2特征衍射峰宽化,强度降低;掺入的La主要以La2O3的形式存在,同时有一部分形成Ti-O-La键;La掺杂可减小TiO2晶粒尺寸及增大催化剂比表面积;与未掺杂的二氧化钛相比较,适当含量的镧掺杂可有效促进TiO2表面光生载流子的分离,从而显著提高其光催化活性。当La/Ti的摩尔比为0.010时,可见光催化性能最好。     

Photocatalytic degradation of gaseous benzene over TiO2/Sr2CeO4: kinetic model and degradation mechanisms

Photocatalytic oxidation of benzene in air was carried out over TiO2/Sr2CeO4 catalysts. The prepared photocatalyst was characterized by SBET, UV-vis diffuse reflectance and XPS. TiO2/Sr2CeO4 absorbs much more visible light than TiO2 in the visible light region. The XPS spectrum shows that the binding energy value of Ti 2p3/2 transfers to a lower value. The main purpose was to investigate the kinetic model and degradation mechanisms. The kinetic data matched well with the Langmuir-Hinshelwood (L-H) kinetic model with the limiting rate constant and the adsorption constant in this case were 0.0064 mg l-1 min-1 and 9.2078 l mg-1, respectively. No gas-phase intermediates were detected by direct GC/FID analysis under the conditions despite the high benzene concentration. Ethyl acetate and (3-methyl-oxiran-2-yl)-methanol were two major identified intermediates which were accompanied by butylated hydroxytoluene, 2,6-bis(1,1-dimethylethyl)-4,4-dimethylycyclohe, 2,5-cyclohexadiene-1,4,dione,2,6-bis(1,1-dim). It is plausible that at least one of these less-reactive intermediates caused the deactivation of the photocatalyst. Finally, the photocatalytic oxidation mechanisms were speculated.     

Graphene oxide (GO) doped CeO2 as potential enhancer of methyl orange degradation

In this article, a simple method for the synthesis of Graphene Oxide-Cerium oxide (GO/CeO₂) is carried out. The prepared sample was characterized in detail, such as scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Raman, Brunauer-Emmett-Teller technology N₂ adsorption-desorption analysis (BET), photoluminescence (PL) and UV-visible diffuse reflectance spectroscopy (DRS). It was indicated that GO was successfully incorporated into CeO₂. The photocatalytic mechanism of GO/CeO₂ was also explained. The MO solution catalyzed by CeO₂ and GO/CeO₂ was analyzed by a UV-visible spectrometer. The efficiency of GO/CeO₂ degrading methyl orange (MO) is improved from 50% to 87% compared to pure CeO₂ under the visible light. GO/CeO₂ exhibited better photocatalytic performance than CeO₂, which indicated GO doping improved the photocatalytic capacity of the CeO₂ catalyst. It may have potential applications in addressing environmental wastewater.     

Photochemical properties of CeO2-coated ZnO nanorods

Well-aligned ZnO nanorods were deposited by a mild hydrothermal process and coated with nanosized CeO2 particles (approximately 5 nm) by an oxidative-soak-coating method at 45 degrees C. The low growth temperature proved useful in avoiding interfacial reaction between the two phases. Correlation of photoluminescence results indicated that the defects responsible for the deep level emission (DLE) from ZnO were largely located at the surface. The CeO2 coating reduced the DLE but also the photocatalytic activity as surficial hydroxyl groups were involved in the nucleation of the CeO2 phase and thus not available for absorption of the methylene blue species for degradation. Still, CeO2 coated ZnO nanorods retained their photocatalytic ability and could be useful as bifunctional catalyst to treat multiple contaminants simultaneously.     

Photocatalytic degradation of gaseous benzene over TiO2/Sr2CeO4: preparation and photocatalytic behavior of TiO2/Sr2CeO4

The paper demonstrates that the photocatalytic activity of TiO(2) towards the decomposition of gaseous benzene in a batch reactor can be greatly improved by loading TiO(2) on the surface of Sr(2)CeO(4). The research investigates the optimum loading amount of TiO(2) on Sr(2)CeO(4) in enhancing the photocatalytic activity of TiO(2). The prepared photocatalyst was characterized by XRD, UV-vis diffuse reflectance and XPS analyses. TiO(2) is loaded on Sr(2)CeO(4) at 773K. TiO(2)/Sr(2)CeO(4) absorbs much more visible light than TiO(2). The XPS spectrum shows that there are Ti, O, C, Sr elements on the surface of the TiO(2)/Sr(2)CeO(4), and that the binding energy value of Ti2p transfers to a lower value. TiO(2)/Sr(2)CeO(4) demonstrates 2.0 times the photocatalytic activity of pure TiO(2). Based upon these observations, the mechanistic role of Sr(2)CeO(4) in the photocatalytic oxidation reaction has been suggested.     

Photocatalytic degradation of methyl orange: influence of H2O2 in the TiO2-based system

The purpose of this study was to investigate the photocatalytic oxidation of a reactive azo dye. The photocatalytic activity of the TiO2 was studied using a reactor equipped with UV-A sources, with maximum emission at 365 nm. The photocatalytic activity of the TiO2 powder (99.9% anatase) and thin films has been measured through the decomposition of methyl orange solutions. The thin film was prepared by doctor blade and spray pyrolysis deposition (SPD). The TiO2 suspensions were prepared at 1 g/L concentration, and the initial methyl orange concentration was fixed at 7.8125 mg/L. The influence of the TiO2 (powder or thin films) and/or O2 and H2O2 on the photobleaching rate, was tested under different experiments, at pH = 5. Thin films (doctor blade) of TiO2 formed of mezo-sized aggregates formed of nanosized anatase crystallites show better photobleaching efficiency than thin film (SPD) due to their large internal surface. The rate is even higher in H2O2 compared to oxygen environment.     

Visible light induced degradation of methylene blue using CeO2/V2O5 and CeO2/CuO catalysts

In the present study, the nanocatalysts CeO₂, V₂O₅, CuO, CeO₂/V₂O₅ and CeO₂/CuO were synthesized by thermal decomposition method. This method is simple, fast and cost effective compared with other preparation methods. The synthesized catalysts were characterized by different techniques. The XRD and XPS results confirmed the structure and the oxidization states of the nanocomposite materials. DRS results suggested that the prepared CeO₂/V₂O₅ and CeO₂/CuO nanocomposites can generate more electrons and holes under visible light irradiation. The photocatalytic activities of prepared catalysts were evaluated using the degradation of aqueous methylene blue solution as a model compound under visible light irradiation. In addition, the nanocomposite (CeO₂/V₂O₅ and CeO₂/CuO) materials were employed to degrade the textile effluent under visible light condition.     

Photocatalytic degradation of Azure and Sudan dyes using nano TiO2

The present study investigates the dependence of photocatalytic rate on molecular structure of the substrate that is degraded. The photocatalytic degradation of Azure (A and B) and Sudan (III and IV) dyes, having similar structure, but different functional groups, were investigated with two catalysts. The photocatalytic activity of solution combustion synthesized TiO(2) (CS TiO(2)) was compared with that of Degussa P-25 for degrading these dyes. The effect of solvents and mixed-solvent system on photodegradation of Sudan III was investigated. The photodegradation rate was found to be higher in solvents with higher polarity. The effect of pH and the presence of metal ions in the form of chloride and nitrate salt, on degradation rate of Azure A was also investigated. The metal ions significantly reduced the photocatalysis rates. A detailed Langmuir-Hinshelwood kinetic model has been developed to explain the effect of metal ions on degradation rate of the substrate. This model elucidates the contribution of holes and electrons towards degradation of the dye.     

Photocatalytic degradation of carbofuran using semiconductor oxides

The photocatalytic degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) was investigated in an aqueous solution using Degussa P-25 TiO2 and ZnO as photocatalysts. The progress of degradation was monitored using TOC analyzer, HPLC, GC-MS and UV-vis spectrophotometer. The effects of various experimental parameters such as initial concentration of carbofuran, pH of the solution, catalyst loading and light intensity were systematically studied in order to achieve maximum degradation efficiency. The complete mineralization of carbofuran was confirmed by TOC analyzer. The degradation with ZnO showed less efficiency than TiO2. The formation of NO(3)(-) was identified and quantified using HPLC. In addition, four different intermediates formed during the degradation process were also identified and characterized by GC-MS. The mineralization rate was compared with lamps of wavelength 254 and 365 nm under similar conditions. The rate with 254 nm was observed to be very close to that of 365 nm.     

Enhanced Photocatalytic Performances of CeO2/TiO2 Nanobelt Heterostructures

CeO₂/TiO₂ nanobelt heterostructures are synthesized via a cost‐effective hydrothermal method. The as‐prepared nanocomposites consist of CeO₂ nanoparticles assembled on the rough surface of TiO₂ nanobelts. In comparison with P25 TiO₂ colloids, surface‐coarsened TiO₂ nanobelts, and CeO₂ nanoparticles, the CeO₂/TiO₂ nanobelt heterostructures exhibit a markedly enhanced photocatalytic activity in the degradation of organic pollutants such as methyl orange (MO) under either UV or visible light irradiation. The enhanced photocatalytic performance is attributed to a novel capture–photodegradation–release mechanism. During the photocatalytic process, MO molecules are captured by CeO₂ nanoparticles, degraded by photogenerated free radicals, and then released to the solution. With its high degradation efficiency, broad active light wavelength, and good stability, the CeO₂/TiO₂ nanobelt heterostructures represent a new effective photocatalyst that is low‐cost, recyclable, and will have wide application in photodegradation of various organic pollutants. The new capture–photodegradation–release mechanism for improved photocatalysis properties is of importance in the rational design and synthesis of new photocatalysts.     

CeO2 quantum dot functionalized ZnO nanorods photoanode for DSSC applications

Cerium oxide quantum dots (CeO₂ QDs) decorated zinc oxide nanorods (ZnO NRs) heterostructures were grown by a combination of solvothermal and chemical bath deposition methods and used for dye sensitized solar cell (DSSC) applications. Transmission electron microscope images showed the formation of CeO₂/ZnO NRs, where ~5 nm CeO₂ QDs were decorated on ZnO NRs having 1–2.5 μm length and 100–150 nm width. Photoluminescence spectra showed the significant increase in UV emission after decoration of ZnO NRs with CeO₂ QDs. DSSC results revealed that the ZnO NRs with CeO₂ QDs leads to an increase in the open circuit voltage and fill factor and exhibited a maximum efficiency of 2.65 %, which was 2.01 times higher than that of unmodified ZnO NRs. The decoration of CeO₂ QDs on the ZnO NRs surface may lead to the formation of barrier layer and hindered the back electron transfer and thereby high light harvesting efficiency.     

Photocatalytic degradation of aqueous propoxur solution using TiO2 and Hbeta zeolite-supported TiO2

Photocatalytic activity of TiO2 and zeolites supported TiO2 were investigated using propoxur as a model pollutant. Hbeta, HY and H-ZSM-5 zeolites were examined as supports for TiO2. Hbeta was chosen as the TiO2 support based on the adsorption capacity of propoxur on these zeolites (Hbeta>HY=H-ZSM-5). TiO2/Hbeta photocatalysts with different wt.% were prepared and characterized by XRD, FT-IR and BET surface area. The progress of photocatalytic degradation of aqueous propoxur solution using TiO2 (Degussa P-25) and TiO2 supported on Hbeta zeolite was monitored using TOC analyzer, HPLC and UV-vis spectrophotometer. The degradation of propoxur was systematically studied by varying the experimental parameters in order to achieve maximum degradation efficiency. The initial rate of degradation with TiO2/Hbeta was higher than with bare TiO2. TOC results revealed that TiO2 requires 600min for complete mineralization of propoxur whereas TiO2/Hbeta requires only 480min. TiO2/Hbeta showed enhanced photodegradation due to its high adsorption capacity on which the pollutant molecules are pooled closely and hence degraded effectively.