High-performance poly-silicon TFTs using HfO/sub 2/ gate dielectric

High-performance low-temperature poly-Si thin-film transistors (TFTs) using high-/spl kappa/ (HfO/sub 2/) gate dielectric is demonstrated for the first time. Because of the high gate capacitance density and thin equivalent-oxide thickness contributed by the high-/spl kappa/ gate dielectric, excellent device performance can be achieved including high driving current, low subthreshold swing, low threshold voltage, and high ON/OFF current ratio. It should be noted that the ON-state current of high-/spl kappa/ gate-dielectric TFTs is almost five times higher than that of SiO/sub 2/ gate-dielectric TFTs. Moreover, superior threshold-voltage (V/sub th/) rolloff property is also demonstrated. All of these results suggest that high-/spl kappa/ gate dielectric is a good choice for high-performance TFTs.     

A study of relaxation current in high-/spl kappa/ dielectric stacks

Dielectric relaxation currents in SiO/sub 2//Al/sub 2/O/sub 3/ and SiO/sub 2//HfO/sub 2/ high-/spl kappa/ dielectric stacks are studied in this paper. We studied the thickness dependence, gate voltage polarity dependence and temperature dependence of the relaxation current in high-/spl kappa/ dielectric stacks. It is found that high-/spl kappa/ dielectric stacks show different characteristics than what is expected based on the dielectric material polarization model. By the drain current variation measurement in n-channel MOSFET, we confirm that electron trapping and detrapping in the high-/spl kappa/ dielectric stacks is the cause of the dielectric relaxation current. From substrate injection experiments, it is also concluded that the relaxation current is mainly due to the traps located near the SiO/sub 2//high-/spl kappa/ interface. As the electron trapping induces a serious threshold voltage shift problem, a low trap density at the SiO/sub 2//high-/spl kappa/ interface is a key requirement for high-/spl kappa/ dielectric stack application and reliability in MOS devices.     

Improved device performance and reliability in high /spl kappa/ HfTaTiO gate dielectric with TaN gate electrode

The device performance and reliability of higher-/spl kappa/ HfTaTiO gate dielectrics have been investigated in this letter. HfTaTiO dielectrics have been reported to have a high-/spl kappa/ value of 56 and acceptable barrier height relative to Si (1.0 eV). Through process optimization, an ultrathin equivalent oxide thickness (EOT) (/spl sim/9 /spl Aring/) has been achieved. HfTaTiO nMOSFET characteristics have been studied as well. The peak mobility of HfTaTiO is 50% higher than that of HfO/sub 2/ and its high field mobility is comparable to that of HfSiON with an intentionally grown SiO/sub 2/ interface, indicative of superior quality of the interface and bulk dielectric. In addition, HfTaTiO dielectric has a reduced stress-induced leakage current (SILC) and improved breakdown voltage compared to HfO/sub 2/ dielectric.     

Integrated high-/spl kappa/ (/spl kappa/ /spl sim/19) MIM capacitor with Cu/low-/spl kappa/ interconnects for RF application

We demonstrate a high-performance metal-high /spl kappa/ insulator-metal (MIM) capacitor integrated with a Cu/low-/spl kappa/ backend interconnection. The high-/spl kappa/ used was laminated HfO/sub 2/-Al/sub 2/O/sub 3/ with effective /spl kappa/ /spl sim/19 and the low-/spl kappa/ dielectric used was Black Diamond with /spl kappa/ /spl sim/2.9. The MIM capacitor (/spl sim/13.4 fF//spl mu/m/sup 2/) achieved a Q-factor /spl sim/53 at 2.5 GHz and 11.7 pF. The resonant frequency f/sub r/ was 21% higher in comparison to an equivalently integrated Si/sub 3/N/sub 4/-MIM capacitor (/spl sim/0.93 fF//spl mu/m/sup 2/) having similar capacitance 11.2 pF. The impacts of high-/spl kappa/ insulator and low-/spl kappa/ interconnect dielectric on the mechanism for resonant frequency improvement are distinguished using equivalent circuit analysis. This letter suggests that integrated high-/spl kappa/ MIM could be a promising alternative capacitor structure for future high-performance RF applications.     

High-/spl kappa//metal-gate stack and its MOSFET characteristics

We show experimental evidence of surface phonon scattering in the high-/spl kappa/ dielectric being the primary cause of channel electron mobility degradation. Next, we show that midgap TiN metal-gate electrode is effective in screening phonon scattering in the high-/spl kappa/ dielectric from coupling to the channel under inversion conditions, resulting in improved channel electron mobility. We then show that other metal-gate electrodes, such as the ones with n+ and p+ work functions, are also effective in improving channel mobilities to close to those of the conventional SiO/sub 2//poly-Si stack. Finally, we demonstrate this mobility degradation recovery translates directly into high drive performance on high-/spl kappa//metal-gate CMOS transistors with desirable threshold voltages.     

High work-function metal gate and high-/spl kappa/ dielectrics for charge trap flash memory device applications

We report the impact of high work-function (/spl Phi//sub M/) metal gate and high-/spl kappa/ dielectrics on memory properties of NAND-type charge trap Flash (CTF) memory devices. In this paper, theoretical and experimental studies show that high /spl Phi//sub M/ gate and high permittivity (high-/spl kappa/) dielectrics play a key role in eliminating electron back tunneling though the blocking dielectric during the erase operation. Techniques to improve erase efficiency of CTF memory devices with a fixed metal gate by employing various chemicals and structures are introduced and those mechanisms are discussed. Though process optimization of high /spl Phi//sub M/ gate and high-/spl kappa/ materials, enhanced CTF device characteristics such as high speed, large memory window, and good reliability characteristics of the CTF devices are obtained.     

Si interlayer passivation on germanium MOS capacitors with high-/spl kappa/ dielectric and metal gate

We have demonstrated the advantages of silicon interlayer passivation on germanium MOS devices, with CVD HfO/sub 2/ as the high-/spl kappa/ dielectric and PVD TaN as the gate electrode. A silicon interlayer between a germanium substrate and a high-/spl kappa/ dielectric, deposited using SiH/sub 4/ gas at 580/spl deg/C, significantly improved the electrical characteristics of germanium devices in terms of low D/sub it/ (7/spl times/10/sup 10//cm/sup 2/-eV), less C- V hysteresis and frequency dispersion. Low leakage current density of 5/spl times/10/sup -7/ A/cm/sup 2/ at 1 V bias with EOT of 12.4 /spl Aring/ was achieved. Post-metallization annealing caused continuing V/sub fb/ positive shift and J/sub g/ increase with increased annealing temperature, which was possibly attributed to Ge diffusion into the dielectric during annealing.     

Nanoscale germanium MOS Dielectrics-part II: high-/spl kappa/ gate dielectrics

In this paper, atomic layer deposition (ALD) and ultraviolet ozone oxidation (UVO) of zirconium and hafnium oxides are investigated for high-/spl kappa/ dielectric preparation in Ge MOS devices from the perspectives of thermodynamic stability and electrical characteristics. Prior to performing these deposition processes, various Ge surface preparation schemes have been examined to investigate their effects on the resulting electrical performance of the Ge MOS capacitors. Interfacial layer-free ALD high-/spl kappa/ growth on Ge could be obtained; yet, insertion of a stable interfacial layer greatly enhanced the electrical characteristics but with a compromise for equivalent dielectric thickness scalability. On the other hand, interfacial layer-free UVO high-/spl kappa/ growth on Ge was demonstrated with minimal capacitance-voltage hysteresis and sub-1.0-nm capacitance equivalent thickness. Finally, the leakage conduction and scalability of these nanoscale Ge MOS dielectrics are discussed and are shown to outperform their Si counterparts.     

Improved interface quality and charge-trapping characteristics of MOSFETs with high-/spl kappa/ gate dielectric

The effects of high-pressure annealing on interface properties and charge trapping of nMOSFET with high-/spl kappa/ dielectric were investigated. Comparing with conventional forming gas (H/sub 2//Ar=4%/96%) annealed sample, nMOSFET sample annealed in high-pressure (5-20 atm), pure H/sub 2/ ambient at 400/spl deg/C shows 10%-15% improvements in linear drain current (I/sub d/) and maximum transconductance (g/sub m,max/). Interface trap density and charge trapping properties were characterized with charge pumping measurements and "single pulsed" I/sub d/-V/sub g/ measurements where reduced interface state density and improved charge trapping characteristics were observed after high pressure annealing. These results indicate that high pressure pure hydrogen annealing can be a crucial process for future high-/spl kappa/ gate dielectric applications.     

A novel program-erasable high-/spl kappa/ AlN-Si MIS capacitor

We demonstrate a programmable-erasable MIS capacitor with a single layer high-/spl kappa/ AlN dielectric on Si having a high capacitance density of /spl sim/5 fF//spl mu/m/sup 2/. It has low program and erase voltages of +4 and -4 V, respectively. Such an erase function is not available in other single layer Al/sub 2/O/sub 3/, AlON, or other known high-/spl kappa/ dielectric capacitors, where the threshold voltage (V/sub th/) shifts continuously with voltage. This device exhibits good data retention with a V/sub th/ change of only 0.06 V after 10 000 s.     

The effect of IrO/sub 2/--IrO/sub 2/--Hf--LaAlO/sub 3/ gate dielectric on the bias-temperature instability of 3-D GOI CMOSFETs

We have studied the bias-temperature instability of three-dimensional self-aligned metal-gate/high-/spl kappa//Germanium-on-insulator (GOI) CMOSFETs, which were integrated on underlying 0.18 /spl mu/m CMOSFETs. The devices used IrO/sub 2/--IrO/sub 2/-Hf dual gates and a high-/spl kappa/ LaAlO/sub 3/ gate dielectric, and gave an equivalent-oxide thickness (EOT) of 1.4 nm. The metal-gate/high-/spl kappa//GOI p-and n-MOSFETs displayed threshold voltage (V/sub t/) shifts of 30 and 21 mV after 10 MV/cm, 85/spl deg/C stress for 1 h, comparable with values for the control two-dimensional (2-D) metal-gate/high-/spl kappa/-Si CMOSFETs. An extrapolated maximum voltage of -1.2 and 1.4 V for a ten-year lifetime was obtained from the bias-temperature stress measurements on the GOI CMOSFETs.     

Characterization of accumulation layer capacitance for extracting data on high-/spl kappa/ gate dielectrics

A new parameter extraction technique has been outlined for high-/spl kappa/ gate dielectrics that directly yields values of the dielectric capacitance C/sub di/, the accumulation layer surface potential quotient, /spl beta//sub acc/, the flat-band voltage, the surface potential /spl phi//sub s/, the dielectric voltage, the channel doping density and the interface charge density at flat-band. The parallel capacitance, C/sub p/(=C/sub sc/+C/sub it/), was found to be an exponential function of /spl phi//sub s/ in the strong accumulation regime, for seven different high-/spl kappa/ gate dielectrics. The slope of the experimental lnC/sub p/(/spl phi//sub s/) plot, i.e., |/spl beta//sub acc/|, was found to depend strongly on the physical properties of the high-/spl kappa/ dielectric, i.e., was inversely proportional to [(/spl phi//sub b/m/sup *//m)/sup 1/2/K/C/sub di/], where /spl phi//sub b/ is the band offset, and m/sup */ is the effective tunneling mass. Extraction of /spl beta//sub acc/ represented an experimental carrier confinement index for the accumulation layer and an experimental gate-dielectric direct-tunneling current index. /spl beta//sub acc/ may also be an effective tool for monitoring the effects of post-deposition annealing/processing.     

Intrinsic mobility evaluation of high-/spl kappa/ gate dielectric transistors using pulsed I/sub d/-V/sub g/

A novel intrinsic mobility extraction methodology for high-/spl kappa/ gate stacks that only requires a capacitance-voltage and pulsed I/sub d/-V/sub g/ measurement is demonstrated on SiO/sub 2/ and high-/spl kappa/ gate dielectric transistors and is benchmarked to other reported mobility extraction techniques. Fast transient charging effects in high-/spl kappa/ gate stacks are shown to cause the mobility extracted using conventional dc-based techniques to be lower than the intrinsic mobility.     

A novel self-aligned offset-gated polysilicon TFT using high-/spl kappa/ dielectric spacers

In this letter, a novel self-aligned offset-gated Poly-Si thin-film transistor (TFT) using high-/spl kappa/ dielectric Hafnium oxide (HfO/sub 2/) spacers is proposed and demonstrated. The HfO/sub 2/ film is deposited by magnetron sputter deposition, and the HfO/sub 2/ spacers are formed by reactive ion etching. The permittivity of the deposited HfO/sub 2/ is approximately 20. Experimental results show that with the high vertical field induced underneath the high-/spl kappa/ spacers, an inversion layer is formed, and it effectively increases the on-state current while still maintaining a low leakage current in the off-state, compared to the conventional lightly doped drain or oxide spacer TFTs. The on-state current in the offset-gated Poly-Si TFT using the HfO/sub 2/ spacers is approximately two times higher than that of the conventional oxide spacer TFT.     

Dopant-free FUSI Pt/sub x/Si metal gate for high work function and reduced Fermi-level pinning

High work function (4.9 eV) on high-/spl kappa/ gate dielectric, which is suitable for bulk p-MOSFET, has been achieved using fully silicided (FUSI) Pt/sub x/Si gate without boron predoping of polysilicon. High concentration of Pt in FUSI Pt/sub x/Si using Ti capping layer on Pt in the FUSI process is a key to achieving high work function and reduced Fermi-level pinning on high-/spl kappa/ dielectric. By combining with substituted Al (SA) gate for nMOSFET, a wide range of work function difference (0.65 eV) between n and pMOSFETs is demonstrated, without any adverse effects of polysilicon predoping.     

Short-channel metal-gate TFTs with modified Schottky-barrier source/drain

A thin active layer, a fully silicided source/drain (S/D), a modified Schottky-barrier, a high dielectric constant (high-/spl kappa/) gate dielectric, and a metal gate are integrated to realize high-performance thin-film transistors (TFTs). Devices with 0.1-/spl mu/m gate length were fabricated successfully. Low threshold voltage, low subthreshold swing, high transconductance, low S/D resistance, high on/off current ratio, and negligible threshold voltage rolloff are demonstrated. It is thus suggested for the first time that the short-channel modified Schottky-barrier TFT is a solution to carrier out three-dimension integrated circuits and system-on-panel.     

Schottky-barrier S/D MOSFETs with high-k gate dielectrics and metal-gate electrode

This letter presents a low-temperature process to fabricate Schottky-barrier silicide source/drain transistors (SSDTs) with high-/spl kappa/ gate dielectric and metal gate. For p-channel SSDTs (P-SSDT) using PtSi sourece/drain (S/D) , excellent electrical performance of I/sub on//I/sub off//spl sim/10/sup 7/-10/sup 8/ and subthreshold slope of 66 mV/dec have been achieved. For n-channel SSDTs (N-SSDTs) using DySi/sub 2-x/ S/D , I/sub on//I/sub off/ can reach /spl sim/10/sup 5/ at V/sub ds/ of 0.2 V with two subthreshold slopes of 80 and 340 mV/dec. The low-temperature process relaxes the thermal budget of high-/spl kappa/ dielectric and metal-gate materials to be used in the future generation CMOS technology.     

Very high density RF MIM capacitors (17 fF//spl mu/m/sup 2/) using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectrics

Using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectric, we have obtained record high MIM capacitance density of 17 fF//spl mu/m/sup 2/ at 100 kHz, small 5% capacitance reduction to RF frequency range, and low leakage current density of 8.9/spl times/10/sup -7/ A/cm/sup 2/. In combination of both high capacitor density and low leakage current density, a very low leakage current of 5.2/spl times/10/sup -12/ A is calculated for a typical large 10 pF capacitor used in RF IC that is even smaller than that of a deep sub-/spl mu/m MOSFET. This very high capacitance density with good MIM capacitor characteristics can significantly reduce the chip size of RF ICs.     

Improvement of voltage linearity in high-/spl kappa/ MIM capacitors using HfO/sub 2/-SiO/sub 2/ stacked dielectric

It is demonstrated that the voltage coefficients of capacitance (VCC) in high-/spl kappa/ metal-insulator-metal (MIM) capacitors can be actively engineered and voltage linearity can be significantly improved maintaining high capacitance density, by using a stacked insulator structure of high-/spl kappa/ and SiO/sub 2/ dielectrics. A MIM capacitor with capacitance density of 6 fF/spl mu/m/sup 2/ and quadratic VCC of only 14 ppm/V/sup 2/ has been demonstrated together with excellent frequency and temperature dependence (temperature coefficients of capacitance of 54 ppm /spl deg/C) as well as low leakage current of less than 10 nA/cm/sup 2/ up to 4 V at 125 /spl deg/C.     

Atomic layer deposition of high-/spl kappa/ dielectric for germanium MOS applications - substrate

In this letter, we present the use of atomic layer deposition (ALD) for high-/spl kappa/ gate dielectric formation in Ge MOS devices. Different Ge surface cleaning methods prior to high-/spl kappa/ ALD have been evaluated together with the effects on inserting a Ge oxynitride (GeO/sub x/N/sub y/) interlayer between the high-/spl kappa/ layer and the Ge substrate. By incorporating a thin GeO/sub x/N/sub y/ interlayer, we have demonstrated excellent MOS capacitors with very small capacitance-voltage hysteresis and low gate leakage. Physical characterization has also been done to further investigate the quality of the oxynitride interlayer.