WO3对Pt/α-Al2O3催化萘深度加氢的促进作用

采用无酸性的α-Al₂O₃为载体,预先沉积WO₃然后浸渍法负载Pt物种,合成了系列Pt-WO₃/α-Al₂O₃催化剂用于萘深度加氢反应,系统地研究了氧化钨物种在萘加氢反应中的作用。通过XRD、Raman、HRTEM、XPS和H₂-TPR技术表征了Pt和WO₃物种在载体表面的分散情况和状态,并利用Py-IR研究了载体负载氧化钨和Pt前后的酸性质变化。在温和的反应条件下（70℃、3 MPa、1 h）Pt-WO₃/α-Al₂O₃催化剂表现出优异的萘深度加氢活性,萘的转化率和十氢萘的选择性均达到100%。结果表明,预先在载体表面引入的WO₃和Pt产生了强相互作用,WO₃提高了Pt物种的分散程度,催化剂的酸性来源于氧化钨物种的引入且和负载量成正比关系。催化剂较强的酸性和较高的Pt分散程度是Pt-WO₃/α-Al₂O₃在低温条件下能够使萘深度加氢的关键因素,对于十氢萘作为储氢介质工艺具有重要的意义。     

Oxidation of carbon black over various Pt/MOx/SiC catalysts

Catalytic activities of various Pt/MO_x/SiC systems for carbon oxidation under simulated diesel exhaust gas were investigated in temperature-programmed reactions. When Pt/MO_x (MO_x=TiO₂, ZrO₂, Al₂O₃) was loaded onto silicon carbide (SiC), the oxidation activities became higher than those of Pt/MO_x alone or other Pt/MO_x/SiC systems (MO_x=Ta₂O₅, WO₃, Nb₂O₅, SnO₂, SiO₂, CeO₂, MoO₃, V₂O₅). Among them, Pt/TiO₂/SiC exhibited the highest activity. We discuss the activity of MO_x=TiO₂, ZrO₂, and Al₂O₃ in connection with NO oxidation activity, adsorption of sulfate onto the support, Pt dispersion, and specific surface area of the catalyst. Furthermore, we investigated the catalytic performance of Pt/TiO₂/SiC in more detail under isothermal conditions and in a staged arrangement.     

Pt/TiO_2催化二甲醚部分氧化重整制氢

二甲醚是一种理想的氢载体,可用于解决氢的储存和运输。以Pt/TiO_2为部分氧化催化剂,结合Ni/Al_2O_3重整催化剂,考察钛前驱体和焙烧温度对二甲醚部分氧化重整制氢反应的影响。结果表明,以Ti(C4H9O)4为原料制备的TiO_2为金红石相,Ti(SO4)2或Ti O(OH)2为原料制备的TiO_2为锐钛矿相;以Ti(C4H9O)4为原料制备的Pt/TiO_2-E催化剂催化性能略好,转化率接近100%,H2收率约90%,表明金红石相TiO_2负载的Pt催化剂略佳;以Ti(SO4)2为原料制备的Pt/TiO_2-S催化剂500℃焙烧可获得金红石相TiO_2。与Pt/Al_2O_3催化剂相比,Pt/TiO_2催化剂具有更好的催化性能,H2收率超过90%,而Pt/Al_2O_3催化剂H2收率约80%。     

添加WO_3对铈钴催化剂CO氧化性能的影响

采用共沉淀法制备xWO_3-Ce O2-Co_3O_4复合型非贵金属CO低温催化剂,考察不同WO_3添加量和空速对催化剂催化活性的影响,并考察催化剂的抗硫性能。通过孔隙结构测试、H2-TPR、FT-IR和SEM等对催化剂进行表征。结果表明,WO_3添加质量分数1%时,催化剂具有最佳的低温活性。在CO进口体积分数0.12%、O2进口体积分数5%和空速15 000 h-1条件下,50℃时,CO转化率即可达到99.6%,60℃时,CO转化率达100%。添加WO_3,催化剂氧化能力增强,催化效率提高。随着空速升高,CO转化率下降。WO_3的加入可有效提高催化剂的比表面积,抑制硫酸盐在催化剂表面聚集,提高催化剂的抗硫性能。     

Hydroisomerization of n-heptane and dehydration of 2-propanol on bulk and supported WO2(Hx)ac on TiO2

Characterization by XPS–UPS and XRD of commercial bulk WO₂ enabled us to identify the presence of four to five layers of WO₃ on the sample surface with an equal amount of W⁵⁺, possibly W₂₀O₅₈ in the interface. The presence of these WO₃ and W₂₀O₅₈ on the WO₂ surface were not detected by XRD. Exposure of commercial bulk WO₂ to hydrogen at temperatures higher than 673 K results in the reduction of surface WO₃ to WO₂ and the formation of the bifunctional WO₂(H_x)_ac phase on its surface. A complete conversion of surface WO₃ to WO₂(H_x)_ac has been obtained following the exposure of the sample to hydrogen for at least 6 h at 773 K. A conversion of 52% of n-heptane at 573 K reaction temperature and a selectivity of 90% in isomerization products, mainly 2,3-MH and multibranched molecules were obtained. The isomerization products distribution is in agreement with the statistical and thermodynamic equilibrium of the methyl-shift mechanism. The stability of the active WO₂(H_x)_ac phase has been tested under prolonged exposure to hydrogen and the reaction mixture. Similar results were obtained in the case of bulk WO₃ and WO₃/TiO₂ systems. Dehydration and dehydrogenation of 2-propanol were studied on these systems at 393 K reaction temperature.     

Magnetron sputtering of gold nanoparticles onto WO3 and activated carbon

In this paper we describe the production and investigation of two supported gold catalyst systems prepared by magnetron sputtering: Au on WO₃ and Au on activated carbon. The magnetron sputtering technique entails using an argon plasma to sputter a high purity gold target producing a flux of gold atoms which are deposited onto a constantly tumbling support material. This technique offers a number of advantages over conventional chemical preparation methods. One advantage is the ability to create gold nanoparticles (diameters <3 nm) on unusual support materials, such as WO₃ and carbon, which are generally not accessible using the ubiquitous deposition-precipitation technique. We present data demonstrating the formation of catalytic gold nanoparticles with average diameters of 1.7 nm (Au/C) and 2.1 nm (Au/WO₃), as well as a substantial number of single atom species on the Au/C sample. Prototypical carbon monoxide oxidation (Au/WO₃) and glycerol oxidation (Au/C) reactions were performed in order to gauge the activity of these catalysts. The WO₃ supported catalyst exhibits substantial catalytic activity from room temperature to 135 °C (0.0018–0.082 mol CO/mol Au s) with an activation energy near 23 kJ/mol. The activity of the Au/C catalyst was compared to a Au/C catalyst prepared from a poly(vinyl alcohol) (PVA) sol. The smaller catalysts prepared by sputtering are more active than the large gold particles prepared using the PVA sol, however the larger gold nanoparticles are substantially more selective towards the production of intermediate products from the oxidation of glycerol.     

Catalytic activation of ceramic filter elements for combined particle separation, NOx removal and VOC total oxidation

The development of a catalytically active filter element for combined particle separation and NO_x removal or VOC total oxidation, respectively, is presented. For NO_x removal by selective catalytic reduction (SCR) a catalytic coating based on a TiO₂–V₂O₅–WO₃ catalyst system was developed on a ceramic filter element. Different TiO₂ sols of tailor-made mean particle size between 40 and 190 nm were prepared by the sol–gel process and used for the impregnation of filter element cylinders by the incipient wetness technique. The obtained TiO₂-impregnated sintered filter element cylinders exhibit BET surface areas in the range between 0.5 and 1.3 m²/g. Selected TiO₂-impregnated filter element cylinders of high BET surface area were catalytically activated by impregnation with a V₂O₅ and WO₃ precursor solution. The obtained catalytic filter element cylinders show high SCR activity leading to 96% NO conversion at 300 °C, a filtration velocity of 2 cm/s and an NO inlet concentration of 500 vol.-ppm. The corresponding differential pressures fulfill the requirements for typical hot gas filtration applications. For VOC total oxidation, a TiO₂-impregnated filter element support was catalytically activated with a Pt/V₂O₅ system. Complete oxidation of propene with 100% selectivity to CO₂ was achieved at 300 °C, a filtration velocity of 2 cm/s and a propene inlet concentration of 300 vol.-ppm.     

WO3–TiO2 monolithic catalysts for high temperature SCR of NO by NH3: Influence of preparation method on structural and physico-chemical properties, activity and durability

The WO₃–TiO₂ catalysts with different WO₃ loadings prepared by the coprecipitation method were investigated in comparison with those prepared by the conventional impregnation method for the activity and durability in the high temperature SCR of NO by NH₃ and the structural and physico-chemical properties which were characterized by BET and XRD measurements, IR, Raman and XPS spectroscopies. The catalyst prepared by coprecipitation, as compared with that prepared by impregnation, was found to exhibit a higher SCR activity at high temperatures and also to possess a larger surface area, higher Brønsted acidity and larger monolayer capacity of the support with WO₃. Increasing the WO₃ loading of the catalysts enhances the SCR activity and simultaneously increases the Brønsted acidity. The observed improvement of SCR activity for the catalyst prepared by coprecipitation is mainly attributed to the higher Brønsted acidity and the presence of the more highly dispersed WO₃ species which is suggested by the larger monolayer capacity of ca. 13 μmol(W)/m² and no crystalline WO₃ on TiO₂ detected with XRD at the high WO₃ loading up to 40 wt.%. The catalyst with 20 wt.% WO₃, as compared with that prepared by impregnation, was found to exhibit a better thermal durability at high temperatures from 550 to 600 °C. The better durability is attributed to that the reduction of the surface area and the formation and subsequent growth of crystalline WO₃ upon aging are more remarkably inhibited.     

NOx storage/reduction over lean-burn automotive catalysts

This paper shows the behavior of a Pt/Ba/γ–Al₂O₃ automotive catalyst in a fixed bed reactor during cyclic operation at lean and rich gas phase conditions at short (seconds) and long (hours) cycling times at different temperatures. Reactor exit gas phase concentrations have been measured and catalyst properties have been determined before and after selective cycling experiments. The experimental results indicate that: (i) Upon 9 h lean and 15 h rich cycling, the NO oxidation efficiency of the catalyst decreases with time while incomplete regeneration is seen, even after 15 h rich exposure with H₂. The cyclic steady state is reached after 3 lean/rich cycles, at which only 60% of the available barium is involved in the NO_x storage/reduction. (ii) The BET surface area, pore volume, and Pt dispersion decrease by approximately 40%, which may be a result of masking of Pt sites or blocking of pores of the barium clusters as BaCO₃ becomes Ba(NO₃)₂. Experiments with catalyst pellet sizes of 180 and 280 μm along with XPS measurements show that blocking of catalyst pellet pores is not taking place. (iii) When applying lean/rich cycling in the order of seconds, it appears that catalyst history and lean/rich timing affect the number of cycles required to arrive at a closed N balance. XRD results after lean exposure confirm the formation of barium nitrate in the bulk of the barium cluster.     

助剂Ba对Pd/Al_2O_3和Pt/Al_2O_3催化剂的C1-C3烷烃催化燃烧性能的影响

通过浸渍法制备了Al_2O_3负载的Pd和Pt催化剂,考察催化剂的甲烷、乙烷和丙烷催化燃烧活性,以及助剂Ba对催化性能的影响。对于Pd/Al_2O_3催化剂,加入Ba使活性物种PdO颗粒变大和还原温度升高,形成更稳定的PdO活性物种,是Pd-Ba/Al_2O_3催化剂活性提升的主要原因。对于Pt/Al_2O_3催化剂,加入Ba助剂使活性物种Pt0含量降低,PtO_x与Al_2O_3载体相互作用增强,使PtO_x物种更难被还原为Pt~0,导致Pt-Ba/Al_2O_3催化剂活性降低。Pd和Pt催化剂催化烷烃氧化反应活性规律一致:丙烷乙烷甲烷。Pd/Al_2O_3催化剂有利于C—H键活化,Pt/Al_2O_3催化剂有利于C—C键活化。Pt/Al_2O_3催化剂对C1-C3烷烃氧化活性的差别明显大于Pd/Al_2O_3催化剂。Pt/Al_2O_3催化剂对碳比例高的烷烃活性更高。     

WO_3负载量对V_2O_5/WO_3-TiO_2催化剂脱硝性能的影响

采用V_2O_5/WO_3-TiO_2作为脱硝催化剂,考察活性组分V_2O_5和助剂WO_3负载量对催化剂脱硝活性和抗硫抗水性能的影响。结果表明,3%V_2O_5/x WO_3-TiO_2催化剂(x=3%、4%、5%、6%、7%、8%、9%、10%)上NOx转化率随着WO_3负载量增加而升高,催化剂反应温度窗口不断拓宽。单独通水蒸汽及同时通SO2和水蒸汽对催化剂的毒害作用均较强,表明H2O和NH3的竞争吸附是催化剂抗硫抗水性能较差的重要原因。SO_2与H_2O和NH_3反应生成亚硫酸铵盐和硫酸铵盐,导致催化剂孔隙堵塞,催化活性降低。     

CeO2改性WO3/g-C3N4光催化氧化脱硫性能

以钨酸铵、六水硝酸铈、尿素为原料,采用熔融法制备CeO₂-WO₃/g-C₃N₄催化剂,并对样品进行XRD、UV-Vis、TEM、PL和XPS表征。结果表明：CeO₂的引入可以提高WO₃在g-C₃N₄上的分散度,抑制光生电子空穴对的复合,同时Ce⁴⁺/Ce³⁺良好的储氧放氧能力有利于氧空位和活性氧的生成,从而有利于WO₃/g-C₃N₄催化剂的催化性能。在以高压钠灯模拟可见光源的条件下,以过氧化羟基异丙苯为氧化剂,考察了CeO₂的加入量对催化剂氧化二苯并噻吩(DBT)性能的影响,结果表明：最佳的CeO₂引入量为5%(质量分数),在80℃、氧硫摩尔比(O/S)为5.0的反应条件下,反应180 min时DBT在WO₃/g-C₃N₄和CeO₂-WO₃/g-C₃N₄催化剂的作用下转化率分别为72.9%和86.4%,且改性后的催化剂可以循环使用8次而催化活性没有明显降低。     

Catalytic effect of platinum on the kinetics of carbon oxidation by NO2 and O2

The effect of a commercial Pt/Al₂O₃ catalyst on the oxidation by NO₂ and O₂ of a model soot (carbon black) in conditions close to automotive exhaust gas aftertreatment is investigated. Isothermal oxidations of a physical mixture of carbon black and catalyst in a fixed bed reactor were performed in the temperature range 300–450 °C. The experimental results indicate that no significant effect of the Pt catalyst on the direct oxidation of carbon by O₂ and NO₂ is observed. However, in presence of NO₂–O₂ mixture, it is found that besides the well established catalytic reoxidation of NO into NO₂, Pt also exerts a catalytic effect on the cooperative carbon–NO₂–O₂ oxidation reaction. An overall mechanism involving the formation of atomic oxygen over Pt sites followed by its transfer to the carbon surface is established. Thus, the presence of Pt catalyst increases the surface concentration of –C(O) complexes which then react with NO₂ leading to an enhanced carbon consumption. The resulting kinetic equation allows to model more precisely the catalytic regeneration of soot traps for automotive applications.     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

SO2 promoted oxidation of ethyl acetate, ethanol and propane

The effect of SO₂ addition on the oxidation of ethyl acetate, ethanol, propane and propene, over Pt/γ-Al₂O₃ and Pt/SiO₂ has been investigated. The reactants (300–800 vol. ppm) were mixed with air and led through the catalyst bed. The conversions below and above light-off were recorded both in the absence and in the presence of 1–100 vol. ppm SO₂. For the alumina-supported catalyst, the conversion of ethyl acetate, ethanol and propane was promoted by the addition of SO₂, while the conversion of propene was inhibited. The effect of SO₂ was reversible, i.e. the conversion of the reactants returned towards the initial values when SO₂ was turned off. However, this recovery was quite slow. The oxidation of propane was inhibited by water, both in absence and presence of SO₂. For the silica-supported catalyst no significant effect of SO₂ could be observed on the conversion of ethyl acetate, ethanol or propane, whereas the conversion of propene was inhibited by the presence of SO₂. In situ FTIR measurements revealed the presence of surface sulphates on the Pt/γ-Al₂O₃ catalyst with and after SO₂ addition. It is proposed that these sulphate groups enhance the oxidation of propane, ethyl acetate and ethanol by creating additional reaction pathways to Pt on the surface of the Pt/γ-Al₂O₃ catalyst.     

三维WO3/rGO复合物的制备及光解水制氢性能研究

通过水热法制备出WO₃/rGO复合物用于可见光下光解水制氢。采用XRD和SEM表征手段对复合物组成、形貌进行研究,同时进行光解水制氢性能测试并对其机理进行探讨。研究结果表明,WO₃样品呈海草状,具有丰富的空隙,可以更大程度上提升光解水制氢性能,WO₃/rGO复合物与未复合石墨烯的WO₃样品比较,其形貌没有明显变化。并且还原氧化石墨烯(rGO)的导电性在提高光感应电荷载流子分离效率中也起着关键作用。WO₃/rGO复合物产氢速率为236μmol/h,而WO₃样品的产氢速率为212μmol/h,氧化石墨与WO₃复合后样品对光解水制氢性能得到提升。增强的光解水制氢性能归因于rGO的优异电导率和WO₃/rGO复合物纳米结构的协同作用。     

Preparation of supported Pt-M catalysts (M = Mo and W) from anion-exchanged hydrotalcites and their catalytic activity for low temperature NO-H2-O2 reaction

The NO-H₂-O₂ reaction was studied over supported bimetallic catalysts, Pt-Mo and Pt-W, which were prepared by coexchange of hydrotalcite-like Mg-Al double layered hydroxides by Pt(NO₂)₄²⁻, MoO₄²⁻, and/or WO₄²⁻ and subsequent heating at 600 °C in H₂. The Pt–Mo interaction could obviously be seen when the catalyst after reduction treatment was exposed to a mixture of NO and H₂ in the absence of O₂. The Pt-HT catalyst showed the almost complete NO conversion at 70 °C, whereas the Pt-Mo-HT showed a negligible conversion. Upon exposure to O₂, however, Pt-Mo-HT exhibited the NO conversion at the lowest temperature of ≥30 °C, compared to ≥60 °C required for Pt-HT. EXAFS/XANES, XPS and IR results suggested that the role of Mo is very sensitive to the oxidation state, i.e., oxidized Mo species residing in Pt particles are postulated to retard the oxidative adsorption of NO as NO₃ and promote the catalytic conversion of NO to N₂O at low temperatures.     

Catalytic performance of a novel ceramic-supported vanadium oxide catalyst for NO reduction with NH3

A novel TiO₂/Al₂O₃/cordierite honeycomb-supported V₂O₅–MoO₃–WO₃ monolithic catalyst was studied for the selective reduction of NO with NH₃. The effects of reaction temperature, space velocity, NH₃/NO ratio and oxygen content on SCR activity were evaluated. Two other V₂O₅–MoO₃–WO₃ monolithic catalysts supported on Al₂O₃/cordierite honeycomb or TiO₂/cordierite honeycomb support, two types of pellet catalysts supported on TiO₂/Al₂O₃ or Al₂O₃, as well as three types of pellet catalysts V₂O₅–MoO₃–WO₃–Al₂O₃ and V₂O₅–MoO₃–WO₃–TiO₂ were tested for comparison. The experiment results show that this catalyst has a higher catalytic activity for SCR with comparison to others. The results of characterization show, the preparation method of this catalyst can give rise to a higher BET surface area and pore volume, which is strongly related with the highly active performance of this catalyst. At the same time, the function of the combined carrier of TiO₂/Al₂O₃ cannot be excluded.     

Highly dispersed NiW/γ-Al2O3 catalyst prepared by hydrothermal deposition method

This article describes a novel hydrothermal deposition method for preparing highly dispersed NiW/γ-Al₂O₃ catalysts and demonstrates its advantages over the conventional impregnation method. Via the hydrothermal precipitation reactions between sodium tungstate and hydrochloric acid and between nickel nitrate and urea, respectively, the active species W and Ni were deposited on γ-Al₂O₃. In the hydrothermal deposition of WO₃, a surfactant hexadecyltrimethyl ammonium bromide (CTAB) was used to prevent the aggregation of WO₃. The characterization results obtained by means of X-ray photoelectron spectroscopy (XPS), N₂ adsorption and high-resolution transmission electron microscopy (HRTEM) measurements showed that compared with the catalyst prepared by the conventional impregnation method, the catalyst with the same metal contents prepared by the hydrothermal deposition had much higher W and Ni dispersion, higher specific surface area, larger pore volume, the significantly decreased slab length and slightly increased stacking degree of sulfided W species, leading to the significantly enhanced dibenzothiophene (DBT) hydrodesulfurization (HDS) activity. The DBT HDS assessment results also revealed that the catalyst containing 17.7 wt% WO₃ and 2.4 wt% NiO prepared by the hydrothermal deposition method had the similar DBT HDS activity as a commercial NiW/γ-Al₂O₃ catalyst containing 23 wt% WO₃ and 2.6 wt% NiO, resulting in the greatly decreased amount of active metals for achieving the same HDS activity.     

Pd–Pt/Al2O3 bimetallic catalysts for the advanced oxidation of reactive dye solutions

The Pd–Pt/Al₂O₃ bimetallic catalysts showed high activities toward the wet oxidation of the reactive dyes in the presence of 1% H₂ together with excess oxygen. Palladium was believed to act as a co-catalyst to spillover the adsorbed H₂ onto the surface of the oxidized Pt surface, and thereby the reducibility of the Pt increased greatly. The organic dye molecule adsorbed on the reduced Pt surface more easily than the oxidized Pt surface under the competition with excess oxygen, which is an essential step for the catalytic wet oxidation (CWO). The Pd–Pt/Al₂O₃ catalysts also produced H₂O₂ from H₂/O₂ mixture, and the hydroxyl radical was formed through the subsequent decomposition of H₂O₂. Additional oxidation of the reactive dyes was obtained with hydroxyl radical. The high activities of the Pd–Pt/Al₂O₃ catalysts were believed to be due to the combined effects of the faster redox cycle resulting from the increased reducibility of Pt surface and the additional oxidation of the reactive dyes with hydroxyl radical.