A RF front-end for DVB-SH based on current conveyors

Inductors are used extensively in Radio Frequency Integrated Circuits to design matching networks, load circuits of voltage controlled oscillators, filters, mixers and many other RF circuits. However, on-chip inductors are large and cannot be ported easily from one process to the next. Due to modern CMOS scaling, inductorless RF design is rapidly becoming possible. In this paper a new methodology for designing the RF frontend necessary for the DVB-SH in a 90 nm CMOS technology based on the use current conveyors (CC) is presented. The RF frontend scheme is composed of a second generation CC (CCII) LNA with asymmetric input and output, an asymmetric to differential converter, and a passive differential mixer followed by two CCII transimpedance amplifiers to obtain a high gain conversion. Measurements show a conversion gain of 20.8 dB, a 14.5 dB noise figure, an input return loss (S11) of −14.3 dB and an output compression point of −3.9 dBm. This combination draws 28.4 mW from a ±1.2 V supply.     

A wideband RF receiver with extended statistical element selection based harmonic rejection calibration

In this paper we present a wideband harmonic rejection (HR) RF receiver design. Both gain mismatch and phase mismatch of the HR mixer have been calibrated using a design and calibration method called extended statistical element selection to achieve best-in-class HR ratio (HRR) performance. The achieved concurrent 3rd order HRR and 5th order HRR are greater than 80 dB and 70 dB, respectively, after calibration. The even order HRR is also calibrated to greater than 80 dB. A single calibration performed at 750 MHz was further observed to be effective over more than two octaves of bandwidth with greater than 70 dB HRR. The receiver was manufactured in 65 nm CMOS technology. Input RF frequency range was 0.15–1 GHz and the receiver consumes 64 mW at 1 GHz. Noise figure is 3.2 dB and out-of-band IIP3 is −7 dBm at a total gain of 48 dB.     

A 0.1–1 GHz low power RF receiver front-end with noise cancellation technique for WSN applications

A low power 0.1–1 GHz RF receiver front-end composed of noise-cancelling trans-conductor stage and I/Q switch stage was presented in this paper. The RF receiver front-end chip was fabricated in 0.18 µm RF CMOS. Measurement results show the receiver front-end has a conversion gain of 28.1 dB at high gain mode, and the single-sideband (SSB) noise figure is 6.2 dB. In the low gain mode, the conversion gain of the receiver front-end is 15.5 dB and the IP1dB is −12 dBm. In this design, low power consumption and low cost is achieved by current-reuse and inductor-less topology. The receiver front-end consumes only 5.2 mW from a 1.8 V DC supply and the chip size of the core circuit is 0.12 mm².     

Single-grain Si thin-film transistors SPICE model,analog and RF circuit applications

Single-grain thin-film transistors (SG-TFTs) fabricated inside location-controlled using μ-Czochralski process exhibit SOI-FETs like performance despite processing temperatures remaining below 350 °C. Thus, the SG-TFT is a potential technology for large-area highly-integrated electronic system and system-in-package, taking advantage of the system-on-flexible substrate and low manufacturing cost capabalities. The SG-TFT is modeled based on the BSIMSOI SPICE model where the mobility parameter is modified to fit the SG-TFT behavior. Therefore, analog and RF circuits can be designed and benchmarked. A two-stage telescopic cascode operational amplifier fabricated in a prototype 1.5 μm SG-TFT technology demonstrates DC gain of 55 dB and unity-gain bandwidth of 6.3 MHz. A prototype CMOS voltage reference demonstrates a power supply rejection ratio (PSRR) of 50 dB. With unity-gain frequency, f_T, in the GHz range, the SG-TFT can also enable RF circuits for wireless applications. A 12 dB gain RF cascode amplifier with integrated on-chip inductors operating in the 433 MHz ISM band is demonstrated.     

A UWB CMOS low-noise amplifier with noise reduction and linearity improvement techniques

In this paper, a highly linear CMOS low noise amplifier (LNA) for ultra-wideband applications is presented. The proposed LNA improves both input second- and third-order intercept points (IIP2 and IIP3) by canceling the common-mode part of all intermodulation components from the output current. The proposed LNA structure creates equal common-mode currents with the opposite sign by cascading two differential pairs with a cross-connected output. These currents eliminate each other at the output and improve the linearity. Also, the proposed LNA improves the noise performance by canceling the thermal noise of the input and auxiliary transistors at the output. Detailed analysis is provided to show the effectiveness of the proposed LNA structure. Post-layout circuit level simulation results using a 90 nm RF CMOS process with Spectre-RF reveal 9.5 dB power gain, -3 dB bandwidth (BW_−3dB) of 8 GHz from 2.4 GHz to 10.4 GHz, and mean IIP3 and IIP2 of +13.1 dBm and +42.8 dBm, respectively. The simulated S₁₁ is less than −11 dB in whole frequency range while the LNA consumes 14.8 mW from a single 1.2 V power supply.     

A 24-dB Ku-band low-power linearized 90-nm amplifier with a built-in output buffer

In this paper, we present a 90-nm high gain (24 dB) linearized CMOS amplifier suitable for applications requiring high degree of port isolation in the K_u-band (13.2–15.4 GHz). The two-stage design is composed of a low-noise common-gate stage and a gain-boosting cascode block with an integrated output buffer for measurement. Optimization of input stage and load-port buffer parameters improves the front-end's linear coverage, port return-loss, and overall gain without burdening its power demand and noise contribution. With low gate bias voltages (0.65–1.2 V) and an active current source, <?10 dB port reflection loss and 3.25–3.41 dB NF are achieved over the bandwidth. The input reflection loss of the overall amplifier lies between ?35 and ?10 dB and the circuit demonstrates a peak forward gain of 24 dB at 14.2 GHz. The output buffer improves the amplifier's forward gain by ～9 dB and pushes down the minimum output return loss to ?22.5 dB while raising the front-end NF by only 0.05 dB. The effect of layout parasites is considered in detail in the 90-nm process models for accurate RF analysis. Monte Carlo simulation predicts 9% and 8% variation in gain and noise figures resulting from a 10% mismatch in process. The K_u-band amplifier including the buffer block consumes 7.69 mA from a 1.2-V supply. The proposed circuit techniques achieve superior small signal gain, GHz-per-milliwatt, and range of linearity when compared with simulated results of reported microwave amplifiers.     

A broadband Low Noise Amplifier with built-in linearizer in 0.13-µm CMOS process

A linearized ultra-wideband (UWB) CMOS Low Noise Amplifier (LNA) is presented in this paper. The linearity performance is enhanced by exploiting PMOS–NMOS common-gate (CG) inverter as a built-in linearizer which leads to cancel out both the second- and third-order distortions. Two inductors are placed at the drain terminals of CG transistors in the built-in linearizer to adjust the phase and magnitude of the third-order distortion. A second-order band-pass Chebyshev filter is utilized in the input port of common-source (CS) configuration to provide broadband input matching at 3.1–10.6 GHz frequency range to a 50-Ω antenna. Series and shunt peaking techniques are employed to extend the bandwidth (BW) and to flatten the gain response. Simulated in 0.13 µm CMOS technology, the CMOS LNA exhibits state of the art performance consuming 17.92 mW of dc power. The CMOS LNA features a maximum gain of 10.24 dB, 0.9–4.1 dB noise figure (NF), and a third-order input intercept point (IIP3) of 6.8 dBm at 6.3 GHz.     

Design of ultra-low voltage integrated CMOS based LNA and mixer for ZigBee application

This work describes the design and implementation of an ultra-low voltage, ultra-low power fully differential low noise amplifier (LNA) integrated with a down-conversion mixer for 2.4 GHz ZigBee application. An inductive-degenerated cascoded LNA is adapted and integrated with a double-balanced mixer which is targeted for low-power application. The proposed design has been extracted and simulated in a 0.13 μm standard CMOS technology. With a power consumption of 905 μW at a voltage headroom of 0.5 V, the proposed LNA-mixer integration reaches out to an integrated noise figure (NF) of 7.2 dB, a gain of 22.3 dB, 1 dB compression point (P1 dB) of −22.3 dBm and input-referred third-order intercept point (IIP3) of −10.8 dBm.     

A low-voltage low-power CMOS fully differential linear transconductor with mobility reduction compensation

A highly linear fully differential CMOS transconductor architecture based on flipped voltage follower (FVF) is proposed. The linearity of the proposed architecture is improved by mobility reduction compensation technique. The simulated total harmonic distortion (THD) of the proposed transconductor with 0.4V_pp differential input is improved from ?42 dB to ?55 dB while operating from 1.0 V supply. As an example of the applications of the proposed transconductor, a 4th-order 5 MHz Butterworth Gm-C filter is presented. The filter has been designed and simulated in UMC 130 nm CMOS process. It achieves THD of ?53 dB for 0.4V_pp differential input. It consumes 345 μw from 1.0 V single supply. Theoretical and simulated results are in good agreement.     

A wideband balun–LNA

In this paper a wideband Low Noise Amplifier (LNA) is introduced which also converts the single-ended input to differential signal at the output. It is based on common-source amplifier with active-feedback to provide input matching. The proposed amplifier has the input matched from 500 MHz to 2.5 GHz. It achieves the maximum voltage gain of 24 dB in this band, while the minimum noise figure (NF) is 2.35 dB. The simulated OIP3 of this amplifier is equal to 21 dBm. The LNA has been designed and simulated in a 0.18 μm CMOS process.     

A novel wide band super transistor based voltage feedback current amplifier

This paper is assigned to the design of voltage feedback current amplifiers (VFCAs). Their operation and interesting characteristics are covered and a novel CMOS VFCA is presented. New ideas based on super transistors (STs) are devised and used to design a high performance VFCA. Benefiting from the interesting properties of STs, the proposed VFCA exhibits high linearity, high output impedance, very low input impedance and wide bandwidth. The proposed circuit is designed using TSMC 0.18 μm CMOS technology parameters and supply voltage of ±0.75 V. Simulation results with HSPICE show low THD of ?60 dB at the output signal, very low impedance of 0.6 Ω and 0.2 Ω at the input and feedback ports respectively and high output impedance of 10 MΩ. Moreover it can provide wide ?3 dB bandwidth of 15.5 MHz. The results prove the high capability of the VFCA in current mode signal processing and encourage strong motivation to develop commercially available VFCAs.     

A high-gain low-power 2–14 GHz ultra-wide-band CMOS LNA for wireless receivers

In this paper, a 2–14 GHz CMOS LNA for ultra-wide-band (UWB) wireless systems is presented. To achieve a good and flat high power gain along with a low noise figure and a high input return loss, the proposed LNA adopts a capacitive cross-coupling common-gate (CG) topology with extra cascaded transistors and inductance. Over the entire 2–14 GHz bandwidth, it exhibits a return loss less than ?10 dB and a small-signal gain of 9 dB. With an input intercept point of ?3 dBm at 5 GHz, it consumes only 9 mW from a 1.5 V supply voltage.     

A hybrid ring coupler quasi-optical antenna-mixer

This paper proposes a hybrid ring coupler quasi-optical antenna-mixer for mitigating local oscillator retransmission. By demonstrating at K-band, the antenna element consists of back-to-back aperture coupled inverted square patch antenna to couple the RF signal at 18.8 GHz to the sigma port of a hybrid ring mixer while the LO signal at 17.5 GHz is coupled to the delta port. The HSCH-9101 Schottky diodes are used to transform the RF signal to the intermediate frequency signal at 1.3 GHz. The results show that the RF/LO isolation is better than 29 dB at 18.19 GHz, and the isotropic conversion loss of the down converted signal is better than 16 dB at 19.25 GHz. The application of the interest is an inverse measurement technique for dielectric property determination.     

Transimpedance amplifier with a compression stage for wide dynamic range optical applications

A high dynamic input transimpedance amplifier was implemented in 130 nm CMOS technology. The proposed TIA is an inverter with a diode connected NMOS and a gate controlled PMOS loads which is cascode connected with the inverter. The square law compression NMOS increases the input photocurrent up to 10 mA. The TIA has an integrated input referred noise current of 135 nA, 227 MHz bandwidth. The TIA shows a transimpedance gain of 59 dBΩ and a 97 dB dynamic range. The TIA consumes 2.3 mA from 1.5 V voltage supply.     

An LP/CBP reconfigurable analog baseband circuit for software-defined radio receivers in 65 nm CMOS

A low pass (LP) and complex band pass (CBP) reconfigurable analog baseband circuit for software-defined radio (SDR) receivers is presented. It achieves 1–15 MHz LP bandwidth, 2–8 MHz CBP bandwidth and 0–36 dB gain range with 1 dB step. Nulling-resistor Miller feed-forward (NRMFF) differential-mode compensation, passive left half-plane (LHP) zero common-mode compensation and Quasi-Floating Gate (QFG) technique are proposed to improve the high frequency performance and driving capability of the embedded fully differential operational amplifier (Op-Amp). The analog baseband circuit has been implemented in 65 nm CMOS. It achieves 15.2 dB m/27.1 dB m IB/OB-IIP3, −2 dB m IP1dB and 71 dB m IIP2 while consuming 3.6–9.1 mW from a 1.2 V power supply and 0.75 mm² chip area.     

Substrate noise isolation improvement in a single-well standard CMOS process

This work describes a fully CMOS compatible methodology, which makes available a pseudo deep n-well in single-well standard CMOS process. The proposed method is based on mask manipulation to accommodate the field implant p-type region into the n-well, and does not require any additional masks or modification in the CMOS process flow. According to the experimental results, the floating NMOS made available by the methodology shows a reduction in the threshold voltage, which implies a slight improvement in its performance, when compared with its standard NMOS counterpart. It was also experimentally demonstrated up to 3 GHz, that the guard-ring field implant/pseudo deep n-well proposed structure improves substrate noise isolation when compared to the classical p+ guard-ring, with a maximum improvement above 20 dB for low frequencies and a minimum of 4 dB at 3 GHz.     

Design of an active CMOS subharmonic mixer with enhanced transconductance

This paper presents a wideband Gilbert subharmonic mixer (SHM) that partly overcomes the fundamental trade-off between radio frequency (RF) and intermediate frequency (IF) currents. Compared to the conventional SHM, the proposed SHM features large gain, low noise figure (NF) and moderate linearity over a wide bandwidth by concurrent usage of regulated-cascode RF-stage and inductive connection between RF and LO stages. Numerical analyses along with circuit-level simulations are given to evaluate the performance of the proposed mixer and facilitate its optimum design. Simulations using a 0.18 μm RF-CMOS process demonstrate that the proposed mixer, at a fixed IF of 100 MHz, exhibits more than 5 dB and 2 dB improvements in conversion gain (CG) and NF, respectively.     

A high-performance 1.2 V–99 μW rail-to-rail CMOS class AB amplifier

This paper presents a compact, reliable 1.2 V low-power rail-to-rail class AB operational amplifier (OpAmp) suitable for integrated battery powered systems which require rail-to-rail input/output swing and high slew-rate while maintaining low power consumption. The OpAmp, fabricated in a standard 0.18 μm CMOS technology, exhibits 86 dB open loop gain and 97 dB CMRR. Experimental measurements prove its correct functionality operating with 1.2 V single supply, performing very competitive characteristics compared with other similar amplifiers reported in the literature. It has rail-to-rail input/output operation, 5 MHz unity gain frequency and a 3.15 V/μs slew-rate for a capacitive load of 100 pF, with a power consumption of 99 μW.     

An Inductor-less Sub-mW Low Noise Amplifier for Wireless Sensor Network Applications

This paper presents a Sub-mW differential Common-Gate Low Noise Amplifier (CGLNA) for ZigBee standard. The circuit takes the advantage of shunt feedback and Dual Capacitive Cross Coupling (DCCC) to reduce power consumption and the bandwidth extension capacitors to support 2.4 GHz ISM band. An amplifier employing these techniques has been designed and simulated in 0.18 µm TSMC CMOS technology. The Simulation results show a gain of 18.2 dB, an IIP3 of −4.32 dBm and a noise figure of 3.38 dB at 2.4 GHz. The proposed LNA consumes only 967 µW from a 1-V supply.