Silicon‐Based Anodes for Lithium‐Ion Batteries: From Fundamentals to Practical Applications

Silicon has been intensively studied as an anode material for lithium‐ion batteries (LIB) because of its exceptionally high specific capacity. However, silicon‐based anode materials usually suffer from large volume change during the charge and discharge process, leading to subsequent pulverization of silicon, loss of electric contact, and continuous side reactions. These transformations cause poor cycle life and hinder the wide commercialization of silicon for LIBs. The lithiation and delithiation behaviors, and the interphase reaction mechanisms, are progressively studied and understood. Various nanostructured silicon anodes are reported to exhibit both superior specific capacity and cycle life compared to commercial carbon‐based anodes. However, some practical issues with nanostructured silicon cannot be ignored, and must be addressed if it is to be widely used in commercial LIBs. This Review outlines major impactful work on silicon‐based anodes, and the most recent research directions in this field, specifically, the engineering of silicon architectures, the construction of silicon‐based composites, and other performance‐enhancement studies including electrolytes and binders. The burgeoning research efforts in the development of practical silicon electrodes, and full‐cell silicon‐based LIBs are specially stressed, which are key to the successful commercialization of silicon anodes, and large‐scale deployment of next‐generation high energy density LIBs.     

MOF‐Derived CuS@Cu‐BTC Composites as High‐Performance Anodes for Lithium‐Ion Batteries

The CuS(x wt%)@Cu‐BTC (BTC = 1,3,5‐benzenetricarboxylate; x = 3, 10, 33, 58, 70, 99.9) materials are synthesized by a facile sulfidation reaction. The composites are composed of octahedral Cu₃(BTC)₂·(H₂O)₃ (Cu‐BTC) with a large specific surface area and CuS with a high conductivity. The as‐prepared CuS@Cu‐BTC products are first applied as the anodes of lithium‐ion batteries (LIBs). The synergistic effect between Cu‐BTC and CuS components can not only accommodate the volume change and stress relaxation of electrodes but also facilitate the fast transport of Li ions. Thus, it can greatly suppress the transformation process from Li₂S to polysulfides by improving the reversibility of the conversion reaction. Benefiting from the unique structural features, the optimal CuS(70 wt%)@Cu‐BTC sample exhibits a remarkably improved electrochemical performance, showing an over‐theoretical capacity up to 1609 mAh g^?1 after 200 cycles (100 mA g^?1) with an excellent rate‐capability of ≈490 mAh g^?1 at 1000 mA g^?1. The outstanding LIB properties indicate that the CuS(70 wt%)@Cu‐BTC sample is a highly desirable electrode material candidate for high‐performance LIBs.     

A Quadruple‐Hydrogen‐Bonded Supramolecular Binder for High‐Performance Silicon Anodes in Lithium‐Ion Batteries

With extremely high specific capacity, silicon has attracted enormous interest as a promising anode material for next‐generation lithium‐ion batteries. However, silicon suffers from a large volume variation during charge/discharge cycles, which leads to the pulverization of the silicon and subsequent separation from the conductive additives, eventually resulting in rapid capacity fading and poor cycle life. Here, it is shown that the utilization of a self‐healable supramolecular polymer, which is facilely synthesized by copolymerization of tert‐butyl acrylate and an ureido‐pyrimidinone monomer followed by hydrolysis, can greatly reduce the side effects caused by the volume variation of silicon particles. The obtained polymer is demonstrated to have an excellent self‐healing ability due to its quadruple‐hydrogen‐bonding dynamic interaction. An electrode using this self‐healing supramolecular polymer as binder exhibits an initial discharge capacity as high as 4194 mAh g⁻¹ and a Coulombic efficiency of 86.4%, and maintains a high capacity of 2638 mAh g⁻¹ after 110 cycles, revealing significant improvement of the electrochemical performance in comparison with that of Si anodes using conventional binders. The supramolecular binder can be further applicable for silicon/carbon anodes and therefore this supramolecular strategy may increase the choice of amendable binders to improve the cycle life and energy density of high‐capacity Li‐ion batteries.     

A Novel Approach to Realize Si‐Based Porous Wire‐In‐Tube Nanostructures for High‐Performance Lithium‐Ion Batteries

Hollow inorganic nanostructures have drawn great attention due to their fascinating features, such as large surface area, high loading capacity, and high permeability. The formation, characterization, and application of partially and entirely hollow structure by applying a Si‐based reactive ion deposition and etching method on silicon nanowire as a template are reported. This fabrication technique is extended to a stainless steel substrate to be used as the binder‐free anode for high capacity and high rate lithium‐ion batteries. The electrochemical analyses exhibit that in addition to the high initial discharge capacity of 4125 mAh g^?1 at a rate of C/16, the best performing electrode shows discharge/charge capacity of as high as 3302.14/2832.1 mAh g^?1, respectively, with an excellent charge capacity retention of 96.7% over 100 cycles at a rate density of 1 C. Even at a rate of 12 C, the as‐designed structure is still able to deliver an impressive 1553 mAh g^?1, which probably is attributed to fast lithium diffusion in its hollow part and high porosity of Si and alumina layer. It is proved that the change in hollowness ratio significantly affects capacity retention and average coulombic efficiency of the lithium‐ion cells.     

Critical Insight into the Relentless Progression Toward Graphene and Graphene‐Containing Materials for Lithium‐Ion Battery Anodes

Used as a bare active material or component in hybrids, graphene has been the subject of numerous studies in recent years. Indeed, from the first report that appeared in late July 2008, almost 1600 papers were published as of the end 2015 that investigated the properties of graphene as an anode material for lithium‐ion batteries. Although an impressive amount of data has been collected, a real advance in the field still seems to be missing. In this framework, attention is focused on the most prominent research efforts in this field with the aim of identifying the causes of such relentless progression through an insightful and critical evaluation of the lithium‐ion storage performances (i.e., 1^st cycle irreversible capacity, specific gravimetric and volumetric capacities, average delithiation voltage profile, rate capability and stability upon cycling). The “graphene fever” has certainly provided a number of fundamental studies unveiling the electrochemical properties of this “wonder” material. However, analysis of the published literature also highlights a loss of focus from the final application. Hype‐driven claims, not fully appropriate metrics, and negligence of key parameters are probably some of the factors still hindering the application of graphene in commercial batteries.     

Graphene‐Bonded and ‐Encapsulated Si Nanoparticles for Lithium Ion Battery Anodes

Silicon (Si) has been considered a very promising anode material for lithium ion batteries due to its high theoretical capacity. However, high‐capacity Si nanoparticles usually suffer from low electronic conductivity, large volume change, and severe aggregation problems during lithiation and delithiation. In this paper, a unique nanostructured anode with Si nanoparticles bonded and wrapped by graphene is synthesized by a one‐step aerosol spraying of surface‐modified Si nanoparticles and graphene oxide suspension. The functional groups on the surface of Si nanoparticles (50–100 nm) not only react with graphene oxide and bind Si nanoparticles to the graphene oxide shell, but also prevent Si nanoparticles from aggregation, thus contributing to a uniform Si suspension. A homogeneous graphene‐encapsulated Si nanoparticle morphology forms during the aerosol spraying process. The open‐ended graphene shell with defects allows fast electrochemical lithiation/delithiation, and the void space inside the graphene shell accompanied by its strong mechanical strength can effectively accommodate the volume expansion of Si upon lithiation. The graphene shell provides good electronic conductivity for Si nanoparticles and prevents them from aggregating during charge/discharge cycles. The functionalized Si encapsulated by graphene sample exhibits a capacity of 2250 mAh g^?1 (based on the total mass of graphene and Si) at 0.1C and 1000 mAh g^?1 at 10C, and retains 85% of its initial capacity even after 120 charge/discharge cycles. The exceptional performance of graphene‐encapsulated Si anodes combined with the scalable and one‐step aerosol synthesis technique makes this material very promising for lithium ion batteries.     

Low‐Temperature Growth of All‐Carbon Graphdiyne on a Silicon Anode for High‐Performance Lithium‐Ion Batteries

In situ weaving an all‐carbon graphdiyne coat on a silicon anode is scalably realized under ultralow temperature (25 °C). This economical strategy not only constructs 3D all‐carbon mechanical and conductive networks with reasonable voids for the silicon anode at one time but also simultaneously forms a robust interfacial contact among the electrode components. The intractable problems of the disintegrations in the mechanical and conductive networks and the interfacial contact caused by repeated volume variations during cycling are effectively restrained. The as‐prepared electrode demostrates the advantages of silicon regarding capacity (4122 mA h g^?1 at 0.2 A g^?1) with robust capacity retention (1503 mA h g^?1) after 1450 cycles at 2 A g^?1, and a commercial‐level areal capacity up to 4.72 mA h cm^?2 can be readily approached. Furthermore, this method shows great promises in solving the key problems in other high‐energy‐density anodes.     

Structural Reorganization–Based Nanomaterials as Anodes for Lithium‐Ion Batteries: Design,Preparation, and Performance

In recent years, with the growing demand for higher capacity, longer cycling life, and higher power and energy density of lithium ion batteries (LIBs), the traditional insertion‐based anodes are increasingly considered out of their depth. Herein, attention is paid to the structural reorganization electrode, which is the general term for conversion‐based and alloying‐based materials according to their common characteristics during the lithiation/delithiation process. This Review summarizes the recent achievements in improving and understanding the lithium storage performance of conversion‐based anodes (especially the most widely studied transition metal oxides like Mn‐, Fe‐, Co‐, Ni‐, and Cu‐based oxides) and alloying‐based anodes (mainly including Si‐, Sn‐, Ge‐, and Sb‐based materials). The synthesis schemes, morphological control and reaction mechanism of these materials are also included. Finally, viewpoints about the challenges and feasible improvement measures for future development in this direction are given. The aim of this Review is to shed some light on future electrode design trends of structural reorganization anode materials for LIBs.     

Sulfur‐Grafted Hollow Carbon Spheres for Potassium‐Ion Battery Anodes

Sulfur‐rich carbons are minimally explored for potassium‐ion batteries (KIBs). Here, a large amount of S (38 wt%) is chemically incorporated into a carbon host, creating sulfur‐grafted hollow carbon spheres (SHCS) for KIB anodes. The SHCS architecture provides a combination of nanoscale (≈40 nm) diffusion distances and C? S chemical bonding to minimize cycling capacity decay and Coulombic efficiency (CE) loss. The SHCS exhibit a reversible capacity of 581 mAh g^?1 (at 0.025 A g^?1), which is the highest reversible capacity reported for any carbon‐based KIB anode. Electrochemical analysis of S‐free carbon spheres baseline demonstrates that both the carbon matrix and the sulfur species are highly electrochemically active. SHCS also show excellent rate capability, achieving 202, 160, and 110 mAh g^?1 at 1.5, 3, and 5 A g^?1, respectively. The electrode maintains 93% of the capacity from the 5th to 1000th cycle at 3 A g^?1, with steady‐state CE being near 100%. Raman analysis indicates reversible breakage of C? S and S? S bonds upon potassiation to 0.01 V versus K/K⁺. The galvanostatic intermittent titration technique (GITT) analysis provides voltage‐dependent K⁺ diffusion coefficients that range from 10^?10 to 10^?12 cm² s^?1 upon potassiation and depotassiation, with approximately five times higher coefficient for the former.     

Reviving Lithium‐Metal Anodes for Next‐Generation High‐Energy Batteries

Lithium‐metal batteries (LMBs), as one of the most promising next‐generation high‐energy‐density storage devices, are able to meet the rigid demands of new industries. However, the direct utilization of metallic lithium can induce harsh safety issues, inferior rate and cycle performance, or anode pulverization inside the cells. These drawbacks severely hinder the commercialization of LMBs. Here, an up‐to‐date review of the behavior of lithium ions upon deposition/dissolution, and the failure mechanisms of lithium‐metal anodes is presented. It has been shown that the primary causes consist of the growth of lithium dendrites due to large polarization and a strong electric field at the vicinity of the anode, the hyperactivity of metallic lithium, and hostless infinite volume changes upon cycling. The recent advances in liquid organic electrolyte (LOE) systems through modulating the local current density, anion depletion, lithium flux, the anode–electrolyte interface, or the mechanical strength of the interlayers are highlighted. Concrete strategies including tailoring the anode structures, optimizing the electrolytes, building artificial anode–electrolyte interfaces, and functionalizing the protective interlayers are summarized in detail. Furthermore, the challenges remaining in LOE systems are outlined, and the future perspectives of introducing solid‐state electrolytes to radically address safety issues are presented.     

Ultra‐light Hierarchical Graphene Electrode for Binder‐Free Supercapacitors and Lithium‐Ion Battery Anodes

A mild and environmental‐friendly method is developed for fabricating a 3D interconnected graphene electrode with large‐scale continuity. Such material has interlayer pores between reduced graphene oxide nanosheets and in‐plane pores. Hence, a specific surface area up to 835 m² g⁻¹ and a high powder conductivity up to 400 S m⁻¹ are achieved. For electrochemical applications, the interlayer pores can serve as “ion‐buffering reservoirs” while in‐plane ones act as “channels” for shortening the mass cross‐plane diffusion length, reducing the ion response time, and prevent the interlayer restacking. As binder‐free supercapacitor electrode, it delivers a specific capacitance up to 169 F g⁻¹ with surface‐normalized capacitance close to 21 μF cm⁻² (intrinsic capacitance) and power density up to 7.5 kW kg⁻¹, in 6 m KOH aqueous electrolyte. In the case of lithium‐ion battery anode, it shows remarkable advantages in terms of the initiate reversible Coulombic efficiency (61.3%), high specific capacity (932 mAh g⁻¹ at 100 mA g⁻¹), and robust long‐term retention (93.5% after 600 cycles at 2000 mAh g⁻¹).