Microstructures and mechanism of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al composites fabricated by the reaction between SiO<Subscript>2</Subscript> and molten aluminum

Al₂ O₃/Al composite was fabricated by the reaction between SiO₂ and molten aluminum. The microstructures of the composite obtained under different reaction conditions were analyzed. The formation mechanism of the composite microstructure was discussed. Results show that the reaction kinetics is influenced remarkably by the reaction temperature, reaction time and the quantity of SiO₂. The morphologies of Al₂O₃ have different features, depending on the reaction temperature. The composite has equaxed Al₂O₃ grains when materials reacted below 1200°C, and the composite is composed of a large number of fine Al₂O₃ grains and aluninum. The composite has a frame-shaped Al₂O₃ microstructure at the reaction temperature of above 1250°C. CHENG Xiao-min: Born in 1964 Funded by the National Natural Science Foundation of China (No. 91522)     

Preparation and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al laminated ceramic matrix composites

Three series of Al2O3/Al laminated ceramic matrix composites,named SPA,SPV and HP,were fabricated by different methods.SPA and SPV were prepared using Al2O3 slices and Al slurry via screen printing and subsequent heat treatment in air or vacuum.HP samples were made by hot pressing the layered stack of Al foils and Al2O3 slices.SEM and XRD were applied to analyze the microstructure and the interlayer crystal phase.The bending strength,fracture toughness and fracture work of the samples made by the three methods were measured and compared.The results show that the composites have much better toughness and higher fracture work than the Al2O3 slice.Among the samples made by the three methods,the samples made by hot pressing have the optimum mechanical performance.The displacement-load curves and fracture mechanism were analyzed.     

Microstructures and Properties of SiC／Al2O3 ／Al- Si Composites Prepared by Reactive Penetration

The composition, microstructures and properties of SiC/Al2O3/Al-Si composites formed by reactive penetration of the molten aluminum into the preforms of SiO2 and SiC were investigated. The composition of the composites was measured by X-ray diffraction ( XRD ). The microstructures of the composites were also measured by scanning electron microscopy (SEM) and optical microscopy. In addition, the factors affecting the properties of the composites were discussed. The experiments show that the mechanical properties of the composites depend on their relative densities and the sizes of the fillers“ SiC gains“. The denser the SiC/Al2O3/Al-Si composites, the higher their bending strength. As the filler “SiC gains“ become fine, the bending strength of the composites increases.     

Effect of matrix composition on physical properties of Al<Subscript>3</Subscript>CON in-situ reaction reinforced corundum composite

60% white corundum used for aggregate, 5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#. They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press, then dried at 200℃ for 24 h. Effects of various additives on 1500 ℃×2 h creep properties of Al3CON reinforced corundum composite were researched. The experimenal results show that creep coefficients of specimens 1#,2#,3# at 1500 ℃×2 h are 1.4×10^- 4, -9.4×10^-4, -22.6×10^-4, respectively. Crushing strength of the slide plate added with suitable additive A after fired at 1500 ℃ ×3 h reaches to 225 MPa, the creep rate is positive all the time from 0% to 0.014% at 1500 ℃ for 2 h. The microstructure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1#, and the strength of the composite is increased. The hot modulus of rupture is up to 59 MPa at 1400 ℃ and the RUL is obviously higher than that at 1700 ℃. Its service life is two times as that of Al2O3-C slide plate when used in the process of pouring steel. The mechanism of creep rate resistance of the composites can be discovered by means of SEM and EDAX analysis. It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas, C, Al and Al2O3 inside the matrix of the composites during in-situ reaction,which gives the composites outstanding creep rate resistance for the dense zone resuiting from Al3CON oxidation that inhibits contraction at the high temperature. Besides, the matrix will turn into the multiphase with high refractoriness, N content and its Al3CON reinforced fiber will further increase accordingly. In addition, Al3CON formed by Al2O3 and C, Al in the matrix with N2 in gas will inhibit the creep rate and also greatly improve the creep rate resistance of the composites.     

Fabrication and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl composites

Al₂O₃/TiAl composites were successfully fabricated by hot-press-assisted exothermic dispersion method with elemental powder mixtures of Ti, Al TiO₂ and Nb₂O₅, and the microstructure and mechanical properties were investigated. The results indicate the fine Al₂O₃ particles tend to disperse on the grain boundaries. The grain size of TiAl matrix decreases and the hardness increases with increasing Nb₂O₅ content. The bending strength and fracture toughness reach to a maximum when Nb₂O₅ content is 6 wt%, under 642 MPa and 6.69 MPa·m^1/2, respectively. Based on the fractography and the observation of crack propagation path, it is concluded that the strengthening and toughening of such composites at room temperature can be attributed to the refinement of the TiAl matrix, the deflection behavior in the crack propagation and the dispersion of Al₂O₃ particles.     

Effect of the silicon powder content on the properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiC-Me composites

By means of transient plastic phase process, the Al₂O₃-SiC-Me composites were produced throungh adding metal aluminium and silicon-powder to Al₂O₃-SiC materials. Under the condition of the same content of silicon and aluminium mixed-powder, the effect of silicon powder addition on properties of Al₂O₃-SiC-Me composites was studied by means of XRD and EPMA analyses in the temperature range of 300°–1600°C. The results indicated that the content of metal phase in the sample at 1600°C increases with increasing silicon powder content. At the same time, when the temperature is lower than 1100°C, the strength of samples gradually increases with increasing temperature. However when the temperature is higher than 1100°C, the strength of samples gradually decreases with increasing temperature, and this change is very small. The results also indicated that at the same sintering temperature, the sample with 6% silicon powder has the maximum strength. Supported by the Chen Yunbo Academician Fund (Grant No. 2007CY021)     

Preparation of MWNTs/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites and their mechanical and electrical properties

Since their discovery by Iijima[1], carbon nanotubes (CNTs) have been the focus in novel materials research. Theoretical and experimental studies show[2-9] that CNTs have extraordinary mechanical and electrical properties. Krishnan et al.[2] have reported that the mean value of Young’s modulus of single-wall nanotubes (SWNTs) is 1.25 TPa. Yu et al.[3] measured Yang’s modulus of multi-wall nanotubes (MWNTs) between 270 and 950 GPa and breaking strength between 11 and 63 GPa. The ele…     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

Tensile properties of an aluminum matrix composite reinforced by SnO<Subscript>2</Subscript>-coated Al<Subscript>18</Subscript>B<Subscript>4</Subscript>O<Subscript>33</Subscript> whisker

Al18B4O33 whisker was coated by SnO2 particles using a chemical precipitation method, and an aluminum matrix composite reinforced by the coated whisker was fabricated by squeeze casting technique. It is found that the SnO2 coating can react with aluminum matrix during squeeze casting process, and Sn particles are induced near the interface between Al18B4O33 whisker and matrix. The tensile test at room temperature indicated that the tensile strength of Al18B4O33 whisker reinforced aluminum matrix composite can be enhanced by suitable content of SnO2 coating. The composites with various whisker coating contents exhibit maximum tensile plasticity at about 300 ℃, and the composite with a suitable whisker coating content could enhance its tensile plasticity evidently, which suggest that an Al18B4O33 whisker-Al composite with both high strength at room temperature and high formability at elevated temperature can be designed.     

Photocatalytic degradation of rhodamine B dye with MWCNT/TiO<Subscript>2</Subscript>/C<Subscript>60</Subscript> composites by a hydrothermal method

Multi-walled carbon nanotube (MWCNT)/TiO2/C60 composite catalysts were prepared by hydrothermal method. TiO2 was deposited on the MWCNT surface. Their photocatalytic activities for degradation of Rhodamine B dye were studied. X-ray diffraction, field emission transmission electron microscopy, ultraviolet-visible light absorption spectrum and photoluminescence spectrum were carried out to characterize the composite catalysts. The results indicated that MWCNTs and C60 could greatly enhance the photocatalytic activity of TiO2.     

Preparation and characteristics of Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/MgF<Subscript>2</Subscript>/Au tunnel junction

The fabrication process of Cu/Al₂O₃/MgF₂/Au double-barrier metal/insulator/metal junction (DMIMJ) was introduced, and more stable light emission from this junction was successfully observed. The light emission physical mechanism of the junction was discussed. Results show that light emission spectrum of this structure locates at wavelength of 250–700 nm with two peaks at around 460 nm and 640 nm, which moves towards shorter wavelength region in comparison with that of the Al/Al₂O₃/Au junction. The light emission efficiency of this junction ranges from 0.7×10⁻⁵–2.0×10⁻⁵, which is 1 to 2 orders higher than that of the single-barrier Al/Al₂O₃/Au junction. The improved properties of this structure should be due to the electrons resonant tunneling effect in the double-barrier.     

Thermal shock resistances of FeMnCr/Cr<Subscript>3</Subscript>C<Subscript>2</Subscript> coatings deposited by arc spraying

Arc spraying with the cored wires was applied to deposit FeMnCr/Cr₃C₂ coatings on low carbon steel substrates, namely FM1, FM2 and FM3. Thermal shock resistances of the coatings were investigated to assess the influence of Cr₃C₂ content on thermal shock resistance. Characteristics of the coatings under thermal cycling test were studied by optical microscopy, field emission scanning electron microscope (FE-SEM) and energy dispersion spectrum (EDS), X-ray diffraction (XRD). The experimental results show that hardness of the coatings increases, bonding strength decreases slightly with increase of the Cr₃C₂ content of the coatings. As a result, FM2 coating possesses the best thermal shock resistance, attributing to its better thermal expansion matches and wettability than those of FM3 coating, less oxide rate than that of FM1 coating restraining from cracks formation and propagation in coatings.     

Effect of Grain Size of CaCO3 and SiO2 on the Formation of C3S Under Different Conditions

The effect of grain size of CaCO3 and SiO2 on the formation of C3S under various conditions, such as rapid heating rate（800 ℃/min）, normal heating rate（30 ℃/min） and in the presence or absence of ZnO, was studied. The results show that the decomposition temperature of CaCO3, the temperature of appearance of liquid phase and the f-CaO content descend when the grain size of CaCO3 and SiO2 becomes smaller, which attributes to the reactive activity enhancement of powders due to the decrease of the particle size. When the grain size of CaCO3 and SiO2 is below 1 μm, the rate of the formation of C3S is greatly raised. A rapid sintering rate and the presence of ZnO have an important effect on the formation of C3S and can lower the temperature of the formation of C3S by about 50 ℃.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> content on residual stress and properties of CAS glass-ceramics

The structure and properties of the glass-ceramics were tested with X-ray diffraction testing instrument,correlative software,and other modern testing means.Then the effect of Al2O3 content on internal stresses in CaO-Al2O3-SiO2 glass-ceramics was studied deeply.In order to study the relationship of Al2O3 to the residual stress of CaO-Al2O3-SiO2 glass-ceramics,X-ray diffraction ＂sin2ψ＂ was used.The means utilized the x radial incidence produced from cathode radial tube,and took the space between crystals as measurement of strain.When the stresses produced,the space between crystals changed and the diffraction peak moved during Bragg diffraction.The magnitude of movement is related to the stresses.The experimental results show the residual stress is considerably high and Al2O3 can influence the mechanical properties of this material hugely.     

Microwave sintering of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript>-WC-Co cermets

Composite powders of nanocrystalline WC-10Co (15wt%),Y2O3 (8mol%) stabilized nanocrystalline ZrO2 (30wt%),industrial cobalt powder (4.5wt%) and submicron Al2O3 (55wt%) composite powders were fabricated by high-energy ball-milling process.The nanocomposite powders were consolidated by microwave sintering process at temperature ranged 1300℃-1550℃ for 15min,respectively.The optimum consolidation conditions,such as temperature,were researched during microwave sintering process.Vickers Hardness of the consolidated cermets was measured by using a Vickers indentation test,and density of specimens was also determined by Archimedes’ principle.Microwave sintering process could not only increase the density of Al2O3-ZrO2-WC-Co cermets and reduce the porosity,but also inhibit abnormal grain growth.     

High-temperature oxidation behavior of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl matrix composite in air

The oxidation behavior of Al₂O₃/TiAl in situ composites fabricated by hot-pressing technology was investigated at 900° in static air. The results indicate that the mass gains of the composites samples decrease gradually with increasing Nb₂O₅ content and the inert Al₂O₃ dispersoids effectively increase the oxidation resistance of the composites. The higher the Al₂O₃ dispersoids content, the more pronounced the effect. The primary oxidation precesses obey approximately the linear laws, and the cyclic oxidation precesses follow the parabolic laws. The oxidized sample containing Ti₂AlN and TiAl phases in the scales exhibits excellent oxidation resistance. The oxide scale formed after exposure at 900°C for 120 h is multiple-layered, consisting mainly of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner TiO₂+Al₂O₃ mixed layer. From the outer layer to the inner layer, TiO₂+Al₂O₃ mixed layer presents the transit of Al-rich oxide to Ti-rich oxide mixed layer. Near the substrate, cross-section micrograph shows a relatively loose layer, and micro- and macro-pores remain on this layer, which is a transition layer and transferres from Al₂O₃+TiO₂ scale to substrate. The thickness of oxide layer is about 20 μm. It is also found that continuous protective alumina scales can not be observed on the surface of oxidation scales. Ti ions diffuse outwardly to form the outer TiO₂ layer, while oxygen ions transport inwardly to form the inner TiO₂+Al₂O₃ mixed layer. Under long-time intensive oxidation exposure, the internal Al₂O₃ scale has a good adhesiveness with the outer TiO₂ scale. No obvious spallation of the oxide scales occurs. The increased oxidation resistance by the presence of in situ Al₂O₃ particulates is attributed to the enhanced alumina-forming tendency and thin and dense scale formation. Al₂O₃ particulates enhance the potential barrier of Ti ions from M/MO interface to O/MO interface, thereby the TiO₂ growth rate decreases, which is also beneficial to improve the oxidation resistance. Moreover, the multi-structure of the TiO₂+Al₂O₃ mixed layer decreases the indiffusion of oxygen ions and also avails to improve the high temperature oxidation resistance of the as-sintered composites. Supported by the Special Program for Education Bureau of Shaanxi Province, China (Grant No. 08JK240) and Scientific Research Startup Program for Introduced Talents of Shaanxi University of Technology, China (Grant No. SLGQD0751)     

Erosion Resistance of CaO-AI203-SiO2 System Glass-Ceramics

The erosion resistance tests were used to research the erosion wear behavior of CaO-Al2O3-SiO2 system glass-ceramic. With the orthogonal test method, the factors thai affect the erosion wear of CaO-Al2O3-SiO2 system galss-ceramic such as pacticles property, impact angle, impact time, size of particles were discussed. The results show that erosion rate rises along a straight line at the early period of erosion wear. With the impact time increased, the erosion rate deviates from original staight line, tendency of the erosion rate increases, With the size of paricle increased , it will have more kinetic energy, the erosion rate of the surface of glass-ceramics ploate rises.     

Fabrication and microstructure of C<Subscript>a</Subscript>TiO<Subscript>3</Subscript> coating by laser cladding

In order to explore the way to improve the adhesion of the calcium phosphate bioceramic coating to Ti substrate, the CaTiO3 coating was fabricated on Ti substrate by laser cladding (LC) using powders of CaCO3 and CaHPO4, and then the composition and microstructure of the coatings were investigated. During LC, CaCO3 can hardly react with Ti, and the coating fabricated using CaCO3 powder is mainly composed of the process of CaO, the decomposition product of CaCO3. Moreover, the coating has a loosened structure and part of it has peeled off from the substrate. CaHPO4 reacts vigorously with Ti, and the coating fabricated using CaHPO4 mainly consists of CaTiO3 which is one of the reaction products between Ti and CaHPO4. Chemical bonding is formed at the interface between coating and substrate, which may enhance the adhesion of the CaTiO3 coating to Ti substrate. Furthermore, CaTiO3 dendrite and eutectic of CaTiO3 and Ca2P2O7 are found on the surface of the coating, implying that a transition can be formed between CaTiO3 and some calcium phosphate bioceramic. So CaTiO3 coating fabricated using CaHPO4 can be a potential candidate to improve the adhesion between calcium phosphate coating and Ti substrate. However, there are also pores and cracks existing in the coating, which may degrade the mechanical properties of the coating.     

Fabrication of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-NaCl composite heat storage materials by one-step synthesis method

Thermal energy storage is an attractive option for effectiveness since it gives flexibility and reduces energy consumption and costs. New composite materials for storage and transformation of heat of NaCl-Al₂O₃ composite materials were synthesized by one-step synthesis method. The chemical composition, morphology, structure, and thermal properties were investigated by XRD, EDS, SEM, and DSC. The results show that NaCl can be absorbed by Al₂O₃ particle from 800 to 900 °C for Al₂O₃ particle surface is rich active structure. The results also indicate that the leakage of NaCl when the phase change can be prevented by Al₂O₃ particles and the enthalpy of phase change of NaCl-Al₂O₃ material is 362 J/g. The composites have an excellent heat storage capacity. Therefore, this study contributes to one new thought and method to prepare high temperature heat storage material and this material can be applied in future thermal engineering.     

Synthesis and luminescence of nano fluorescent powder of Y<Subscript>4</Subscript>Al<Subscript>2</Subscript>O<Subscript>9</Subscript>: Eu<Superscript>3+</Superscript>

Nano fluorescent powder of Y₄Al₂O₉: Eu³⁺ was synthesized by sol-gel method. The XRD shows that the product prepared at 900°C is pure-phase Y₄Al₂O₉: Eu³⁺. The Y₄Al₂O₉ powder is nano-size crystal testified by BF and ED analysis of TEM. The grain diameter of Y₄Al₂O₉ is in the range between 20 and 50nm, and its average is 30 nm. The luminescent spectra show that Eu³⁺ ious occupy two kinds of sites in Y₄Al₂O₉ crystal lattice. One is in the strict inversion center, and the other is in off lying inversion center. When excited with UV light (λ=254nm), Y₄Al₂O₉: Eu³⁺ exhibits an orange emission bond at λ=590 nm due to the⁵D_o→⁷F₁ transition and a red emission band at λ=610 nm due to⁵D_o→⁷F₂ transition. YUAN Xi-ming: Born in 1951 Funded by Key Scientific and Technological Project of Hubei Province (2001 AA102A03)