Effects of CaO and Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> on the reduction of high silicon iron ores

The effects of CaO and Na₂CO₃ on the reduction of high silicon iron ores at 1 250 °C were studied. The experimental results showed that the metallization rate was significantly hindered by the addition of CaO and Na₂CO₃, particularly at the early stage of roasting, compared to the rate without additives. In the absence of additives, iron oxides were quickly reduced to metallic iron, and fayalite was difficult to form. When CaO and Na₂CO₃ were added, the low reducible iron-containing silicate compounds formed and melted, subsequently retarding the metallization process. The inhibition of Na₂CO₃ was more noticeable than that of CaO, and higher Na₂CO₃ doses resulted in stronger inhibition of the increased metallization rate. However, when Na₂CO₃ was added prior to CaO, the liquid phase formed, which facilitated the growth of the metallic phase. To reinforce the separation of the metallic phase and slag, an appropriate amount of liquid phase generated during the reduction is necessary. It was shown that when 10% CaO and 10% Na₂CO₃ were added, a high metallization rate and larger metallic iron particles were obtained, thus further decreasing the required Na₂CO₃ dosage.     

Microstructures and mechanism of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al composites fabricated by the reaction between SiO<Subscript>2</Subscript> and molten aluminum

Al₂ O₃/Al composite was fabricated by the reaction between SiO₂ and molten aluminum. The microstructures of the composite obtained under different reaction conditions were analyzed. The formation mechanism of the composite microstructure was discussed. Results show that the reaction kinetics is influenced remarkably by the reaction temperature, reaction time and the quantity of SiO₂. The morphologies of Al₂O₃ have different features, depending on the reaction temperature. The composite has equaxed Al₂O₃ grains when materials reacted below 1200°C, and the composite is composed of a large number of fine Al₂O₃ grains and aluninum. The composite has a frame-shaped Al₂O₃ microstructure at the reaction temperature of above 1250°C. CHENG Xiao-min: Born in 1964 Funded by the National Natural Science Foundation of China (No. 91522)     

Phase structure and electrical properties of La<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped BiInO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ceramics with high curie temperature

The phase structure and electrical properties of pure and La2O3-doped Bi-InO3-PbTiO3 （BI-PT） ceramics were studied respectively. In （1 -x）BI-xPT （x=0.72-0.80） ceramics, the stability of tetragonal phase increased with increasing x, and pure perovskite structure was obtained for x=-0.80 ceramics. The phase transition temperature range was between 575 ℃ and 600 ℃ for x=0.72-0.80 ceramics, higher than that of PT （-490 ℃）. The c/a ratio almost linearly decreased with increasing La2O3 content in x-0.80 ceramics. It is believed that Pb^2＋ vacancies were formed by La^3＋ substituting Pb^2＋ in La2O3-doped BI-PT ceramics. Tc shifted to lower temperature by 30 ℃/mol% La2O3. The maximum dielectric constant 8557 around 559 ℃ was exhibited in 0.5mol%-doped BI-0.80PT ceramics. La2O3-doped ceramics could be poled resulting from decreasing of c/a ratio and improving of dielectric loss and resistivity. The maximum piezoelectric coefficient d33 was 12 pC/N for 2mol%-doped BI-0.80PT ceramics.     

Molten Salt Synthesis of Ba（ Mgl／3Nb2／3 ）O3 Powder

The single-phrase Ba(Mgl/3Nb2/3)O3(BMN) powder was saccessfully prepared by the KCImolten salt synthesis(MSS) method. The temperature for single-phase BMN powders by MSS was about 400℃ lower than that by the solid-phase method. The average particle size (APS) was about 0.91,u.m at 900℃ and increased with increasing synhesis temperature. Based on the APS, the activation energy for particle growth in theMSS, whose value was 64. 1kJmol^-1.was attained. The sinterability of the powder prepared by MSS method wasbetter than that pretared by solid-phase method.     

Preparation and optical properties of Er<Superscript>3+</Superscript>: Na<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> transparent glass-ceramics

Na₂O-Al₂O₃-SiO₂ glass-ceramics doped with Er³⁺ ions were synthesized by the conventional melt quenching technique at a low melting temperature. The samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis-NIR scanning spectrophotometry, and fluorescence spectrometry. The results show that the main crystalline phase of glass-ceramics is nepheline.The best heat-treatment process is at 520 °C for 2 h. Because the up-conversion luminescence and near infrared luminescence properties of glass doped with Eu³⁺ are studied in detail.     

Controlled preparation of monodisperse CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by a facile method

CoFe2O4 nanoparticles (NPs) were synthesized by coprecipitation method using FeCl3·6H2O and CoCl2·6H2O as precursors.The synthesized conditions were optimized,such as added means of precipitator,quantity of precipitator,the mol ratio of Fe 3+ to Co2+,reaction temperature and pH value.The synthesized material was characterized by XRD,TEM,FTIR,EDS,Raman and its magnetic properties were studied by VSM.The experimental results confirm that the sample is cubic spinel structure CoFe2O4 with a narrow size distribution and a good dispersion feature.CoFe2O4 NPs with well-controlled shape and size was obtained at 70℃.The magnetic properties indicate superparamagnetic behavior and good saturated magnetization.     

Investigation on phase evolution of the ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass ceramics

ZnO-B₂O₃-SiO₂-Al₂O₃-Na₂O glass doped with nucleating agent TiO₂ was prepared with melting-quenching method and the effect of nucleating agent on the crystallization behavior and phase evolution of this glass was investigated by differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The experimental results show that the glass transition temperature and the first crystallization temperature decrease from 630 °C and 765 °C to 595 °C and 740 °C, respectively, with introduction of TiO₂ into glass. There is no diffraction peaks in the XRD pattern but it is no longer transparent for the base glass without nucleating agent after heat treatment, which suggests the serious phase separation occurred, and the observation by SEM indicates that the phase separation is developed by nucleation and growth mechanism. However, there are two different crystals ZnAl₂O₄ and NaAlSiO₄ present in the glass containing TiO₂ after heat treating at 575 °C for 2 h and 740 °C for 6 h, respectively. What is interesting is that NaAlSiO₄ disappears as the crystallization time at 740 °C increases from 6 h to 12 h, and more ZnAl₂O₄ crystal is formed, namely, the further formation of ZnAl₂O₄ is at cost of NaAlSiO₄ with increasing crystallization time. And observation of the morphology of glass ceramics shows great difference with increasing crystallization time. Moreover, the ability of ZnO-B₂O₃-SiO₂-Al₂O₃-Na₂O glass ceramics against attacking of 1M HCl solution is increased by the crystals precipitated in heat treatment process.     

Novel preparation and XPS analysis of V<Subscript>2</Subscript>O<Subscript>5</Subscript> xerogel

The V₂O₅ sol was fabricated by ultra-fast quenching. The vanadium with low valence (V⁴⁺) was found in V₂O₅ xerogel films by XPS analysis. The technology of oxygen top-blown was applied to analyze the XPS spectrum difference of V₂O₅ xerogel when the powder of V₂O₅ was melting in air or in oxygen atmosphere. The results show that the different melting atmosphere has certain influences on the chemical valence of V₂O₅ xerogel. ZHU Quan-yao: Born in 1968 Funded by the National Natural Science Foundation of China (No. 50172036, No. 59802009)     

Effect of Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> and CaCO<Subscript>3</Subscript> on coreduction roasting of blast furnace dust and high-phosphorus oolitic hematite

Iron was recovered from blast furnace dust and high-phosphorus oolitic hematite in the presence of Na₂CO₃ and CaCO₃ additives. The functions of Na₂CO₃ and CaCO₃ during the coreduction roasting process were investigated by XRD and SEM-EDS analyses. Results indicate that these additives not only hinder the reduction of fluorapatite, CaCO₃ also decreases the P content of direct reduced iron (DRI) by increasing the reduction alkalinity. P remains as fluorapatite in the slag, which can be removed by grinding and magnetic separation under optimal conditions. The Na₂CO₃ promotes hematite reduction and improves the iron recovery (ε_Fe) by replacing the FeO from fayalite, which results in quick growth and aggregation of metallic iron and improvement of ε_Fe in DRI. A DRI with 91.88 mass% Fe, and 0.065 mass% P can be achieved at a recovery of 87.86 mass% under the optimal condition.     

Nanocomposite films of V<Subscript>2</Subscript>O<Subscript>5</Subscript>−MoO<Subscript>3</Subscript> xerogel with poly ethylene oxide intercalation

Poly ethylene oxide (PEO)_x−V₂O₅−V₂O₅−MoO₃ (x=0, 0.5, 1) films were prepared by the sol-gel method. The synthesis and structure of the films were investigated by XRD, TG-DTA, FTIR, etc. The results show that V₂O₅−MoO₃ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1. 7898 nm at x=1 after the nanocomposite films were dried, and PEO in the interlayer changes the interface structure by forming hydrogen bonds with V=0 bands. CV measurement indicates that the intercalation of PEO improves insertion/extration properties of Li⁺ ions in the interlayer. ZHENG Jin-xia: Born in 1976 Funded by the National Natural Science Foundation of China (No. 50172036) and Natural Science Foundation of Hubei Province(No. 2001ABB083)     

Synthesis and electrochemical properties of Cr-doped Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode materials for lithium-ion batteries

Cr-doped Li₃V₂(PO₄)₃ cathode materials Li₃V_2−x Cr _x (PO₄)₃ were prepared by a carbothermal reduction(CTR) process. The properties of the Cr-doped Li₃V₂(PO₄)₃ were investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM), and electrochemical measurements. Results show that the Cr-doped Li₃V₂(PO₄)₃ has the same monoclinic structure as the undoped Li₃V₂(PO₄)₃, and the particle size of Cr-doped Li₃V₂(PO₄)₃ is smaller than that of the undoped Li₃V₂(PO₄)₃ and the smallest particle size is only about 1 μm. The Cr-doped Li₃V₂(PO₄)₃ samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram (CV), and electrochemical impedance spectra(EIS). The optimal doping content of Cr was that x=0.04 in the Li₃V_2−x Cr _x (PO₄)₃ samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Cr-doping. The improved electrochemical performances of the Cr-doped Li₃V₂(PO₄)₃ cathode materials are attributed to the addition of Cr³⁺ ion by stabilizing the monoclinic structure. Funded by the Guangxi Natural Science Foundation(No. 0832259) and the National Basic Research Program of China (No. 2007CB613607)     

Synthesis and characterization of (PEO)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>−(V<Subscript>0.85</Subscript>Mo<Subscript>0.15</Subscript>)<Subscript>2</Subscript>O<Subscript>5</Subscript> nanocomposite films

(PEO) _x −(V_0.85Mo_0.15)₂O₅(x=0,0.5,1.0) nanocomposite films were prepared by a modified sol-gel method. The structure of the films was analyzed by XRD, and the DC electrical conductivity. Cyclic voltammogram and optical spectral transmittance were investigated. The results show that the (V_0.85Mo_0.15)₂O₅ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1.7897 nm at x=1.0. The introduction of MoO₃ improved the DC electrical conductivities of the films due to the generation of V₄₊ to maintain the electrical neutrality of the oxides. PEO intercalated in the interlayer of (V_0.85Mo_0.15)₂O₅ oxides has interaction with the oxides, enhancing the amount of Li⁺ ions inserted into the interlayer of the oxides. Moreover, the intercalation of PEO into the interlayer of (V_0.85Mo_0.15)₂O₅ oxides improved the cathodic electrochromic property in near ultraviolet region and anodic electrochromic property in visible range. JIANG Cong-sheng: Born in 1963 Supported by the Science Foundation of Hubei Province (Grant No. 2001ABB083)     

Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Synthesis and characterization of biomimetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/coke magnetic nanoparticles composite material

A composite material (Fe₃O₄/Coke) using coke supported Fe₃O₄ magnetic nanoparticles was successfully prepared via an in-situ chemical oxidation precipitation method and characterized by SEM, XRD, Raman, and FTIR. The results showed that the Fe₃O₄ nanoparticles existed steadily on the surface of coke, with better dispersing and smaller particle size. The catalytic ability of Fe₃O₄/Coke were investigatied by degrading p-nitrophenol (P-NP). The results showed that the apparent rate constant for the P-NP at 1.0 g·L^?1 catalyst, 30 mmol·L^?1 H₂O₂, pH=3.0, 30 °C and the best ratio of Coke/Fe₃O₄ 0.6, was evaluated to be 0.027 min^–1, the removal rate of COD_Cr was 75.47%, and the dissolubility of Fe was 2.42 mg·L^–1. Compared with pure Fe₃O₄, the catalytic ability of Fe₃O₄/Coke in the presence of H₂O₂ was greatly enhanced. And Fe₃O₄/Coke was a green and environmental catalyst with high catalytic activity, showing a good chemical stability and reusability.     

Synthesis and luminescence of nano fluorescent powder of Y<Subscript>4</Subscript>Al<Subscript>2</Subscript>O<Subscript>9</Subscript>: Eu<Superscript>3+</Superscript>

Nano fluorescent powder of Y₄Al₂O₉: Eu³⁺ was synthesized by sol-gel method. The XRD shows that the product prepared at 900°C is pure-phase Y₄Al₂O₉: Eu³⁺. The Y₄Al₂O₉ powder is nano-size crystal testified by BF and ED analysis of TEM. The grain diameter of Y₄Al₂O₉ is in the range between 20 and 50nm, and its average is 30 nm. The luminescent spectra show that Eu³⁺ ious occupy two kinds of sites in Y₄Al₂O₉ crystal lattice. One is in the strict inversion center, and the other is in off lying inversion center. When excited with UV light (λ=254nm), Y₄Al₂O₉: Eu³⁺ exhibits an orange emission bond at λ=590 nm due to the⁵D_o→⁷F₁ transition and a red emission band at λ=610 nm due to⁵D_o→⁷F₂ transition. YUAN Xi-ming: Born in 1951 Funded by Key Scientific and Technological Project of Hubei Province (2001 AA102A03)     

Nanostructure and formation mechanism of Pt-WO<Subscript>3</Subscript>/C nanocatalyst by ethylene glycol method

Pt-WO3 nanoparticles uniformly dispersed on Vulcan XC-72R carbon black were prepared by an ethylene glycol method.The morphology,composition,nanostructure,electrochemical characteristics and electrocatalytic activity were characterized,and the formation mechanism was investigated.The average particle size was 2.3 nm,the same as that of Pt/C catalyst.The W/Pt atomic ratio was 1/20,much lower than the design of 1/3.The deposition of WO3·xH2O nanoparticles on Vulcan XC-72R carbon black was found to be very difficult by TEM.From XPS and XRD,the Pt nanoparticles were formed in the colloidal solution of Na2WO4,the EG insoluble Na2WO4 resulted in the decreased relative crystallinity and increased crystalline lattice constant compared with those of Pt/C catalyst and,subsequently,the higher specific electrocatalytic activity as determined by CV.The Pt-mass and Pt-electrochemically-active-specific-surface-area based anodic peak current densities for ethanol oxidation were 422.2 mA·mg-1Pt and 0.43 mA·cm-2Pt,1.2 and 1.1 times higher than those of Pt/C catalyst,respectively.     

Hydrothermal preparation and photocatalytic water splitting properties of ZrW<Subscript>2</Subscript>O<Subscript>8</Subscript>

ZrW₂O₈ was prepared by adjusting Zr:W mole ratio and HCl concentration in hydrothermal reaction processes. The obtained sample was crystallized in α-ZrW₂O₈ phase (cubic, P2₁3), with band gap energy of 4.0 eV. The properties of photocatalytic water splitting were examined under UV light irradiation. The average rate of H₂ evolution over 0.3wt% Pt/ZrW₂O₈ in the presence of CH₃OH as electron donor (ED) was 23.4 μmol/h, while the average rate of O₂ evolution over ZrW₂O₈ in the presence of AgNO₃ as electron scavenger (ES) was 9.8 μ mol/h. Moreover, H₂ was evolved over 0.3wt% Pt/ZrW₂O₈ from pure water splitting at a rate of 5.2 μ mol/h. The study indicated that the band structure of ZrW₂O₈ was suitable for reducing H⁺ to H₂ and oxidizing H₂O to O₂. The band structure and photocatalytic water splitting properties of ZrW₂O₈, different from either ZrO₂ (5.0 eV) or WO₃ (2.7 eV), were attributed to the hybridization of W5d and Zr4d in conduction band (CB) as well as the change in crystal structure.     

Optical and magnetic properties of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nano-composite films

Fe₂O₃/SiO₂ nano-composite films were prepared by sol-gel technique combining heat treatment in the range of 100–900 °C. The particle size was observed by FE-SEM. Optical properties of the films were investigated by UV-visible spectra. Structural and magnetic characteristics were investigated through FT-IR and VSM. The transparency of the Fe₂O₃/SiO₂ nano-composite films decreased with the content of the Fe₂O₃. Water and organic solvent in the films were evaporated with heat treatment, so the transparency of the films was enhanced under high temperature. It is also found that the saturation magnetization (M _s) of the films increases with the temperature. As the content of the Fe₂O₃ increases, when the content of the Fe₂O₃ is around 30wt%, the M _s of the films has a maximum value.     

Effect of aluminum addition on microstructure and properties of SiO<Subscript>2</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-CaO vitrified bond

Influence of aluminum addition on the structures and properties of SiO₂-B₂O₃-Al₂O₃-CaO vitrified bond at low sintering temperature and high strength was discussed. FTIR and XRD analyses were used to characterize the structures of the basic vitrified bond with different contents of aluminum. The bending strength and the thermal expansion coefficients were also tested. Meanwhile, the microstructures of composite specimens at sintering temperature of 660 °C were observed by scanning electron microscope (SEM). The experimental results showed that the properties of vitrified bond with 1wt% aluminum were improved significantly, where the bending strength, Rockwell hardness, and thermal expansion coefficient of the vitrified bond reached 132 MPa, 63 HRB, and 6.73×10^-6 °C^-1, respectively.     

Direct synthesis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-modified Li(Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode materials for lithium ion batteries

To improve the cyclic stability at high temperature and thermal stability, the spherical Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ was synthesized by a modified co-precipitation method, and the physical and electrochemical properties were studied. The TEM images showed that Li(Ni_0.5Co_0.2Mn_0.3)O₂ was modified successfully with nano-Al₂O₃. The discharge capacity retention of Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ maintained about 99% after 200 cycles at high temperature (55 °C), while that of the bare one was only 86%. Also, unlike bare Li(Ni_0.5Co_0.2Mn_0.3)O₂, the Al₂O₃-modified material cathode exhibited good thermal stability.