Eutectic Composition in the Pseudobinary of Y4Al2O9 and Y2O3

The eutectic composition between Y₄Al₂O₉ and Y₂O₃ was determined using electron probe microanalysis (EPMA) on directionally solidified specimens with hypo- and hypereutectic compositions. The microstructures of the specimens as a function of composition differ considerably with small deviation from the eutectic composition (70.5 mol% Y₂O₃ and 29.5 mol% Al₂O₃). Based on the current results and other published data, the pseudobinary system between Al₂O₃ and Y₂O₃ is revised.     

Thermal Expansion and Athermal Phase Transition of Y4AI2O9 Ceramics

Thermal expansion of Y₄A1₄O₉ ceramics prepared at 1600° and 1800°C was measured from room temperature to 1500°C in air. Volume changes at the phase transition of Y₄A1₂O₉, along with thermal hysteresis, were observed around 1400°C. The volume of the high-temperature phase was about 0.5% lower than that of the low-temperature phase. The hysteresis width for the sample prepared at 1600°C was 56°C, wider than that (14°C) for the sample prepared at 1800°C. The averages of phase transition start temperatures on heating and on cooling for these samples were, however, almost the same at 1377°C. The phase transitions did not occur at fixed temperatures, and the proportions of the high-temperature phase and the low-temperature phase did not change with time as long as the temperature remained constant ( athermal character). The sample prepared at 1800°C also showed another thermal hysteresis behavior from room temperature to about 1000°C.     

Phase Transition of Rare-Earth Aluminates (RE4Al2O9) and Rare-Earth Gallates (RE4Ga2O9)

Lattice parameters of RE₄Al₂O₉ (RE = Y, Sin, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Yb) prepared at 1600–1800°C and those of RE₄Ga₂O₉ (RE = La, Pr, Nd, Sm, Eu, and Gd) prepared at 1400–1600°C were refined by Rietveld analysis for the X-ray powder diffraction patterns. The parameters increased linearly with the ionic radius of the trivalent rare-earth elements ( r _RE). High-temperature differential calorimetry and dilatometry revealed that both RE₄Al₂O, and RE₄Ga₂O, have reversible phase transitions with volume shrinkages of 0.5–0.7% on heating and thermal hystereses. The transition temperatures (7_tr) decreased from 1300°C (Yb) to 1044°C (Sm) for RE₄A1₂O₉, except for Y₄Al₂O₉ ( T_tr = 1377°C), and from 1417°C (Gd) to 1271°C (La) for RE₄Ga₂O, with increasing ionic radius of the rare-earth elements. These transition temperatures were plotted on a curve against the ionic radius ratio of Al³⁺ or Gd³⁺ and RE³⁺ ( r _A1Ga/r_RE) except for Y₄Al₂O₉.     

High-Temperature Phase Relations in the System Y2O3-Ta2O5

The phase relations for the system y₂o₃–Ta₂o₅ in the composition range 50 to 100 mol% Y₂O₃ have been studied by solid-state reactions at 1350°, 1500°, or 17000C and by thermal analyses up to the melting temperatures. Weberite-type orthorhombic phases (W2 phase, space group C222₁), fluorite-type cubic phases (F phase, space group Fm3m )and another orthorhombic phase (O phase, space group Cmmm )are found in the system. The W2 phase forms in 75 mol% Y₂O₃ under 17000C and O phase in 70 mol% Y₂O₃ up to 1700°C These phases seem to melt incongruently. The F phase forms in about 80 mol% Y₂O₃ and melts congruently at 2454° 3°C. Two eutectic points seem to exist at about 2220°C 90 mol% Y²O₃, and at about 1990°C, 62 mol% Y₂O₃. A Phase diagram including the above three phases were not identified with each other.     

High-Temperature Creep of Y2O3-Stabilized ZrO2

The compression creep behavior of Y₂O₃-stabilized ZrO₂ (YSZ) was studied at temperatures to 2000 ° C. The function of Y₂O₃ content and grain size was tested in specimens with various impurity concentrations and porosity distributions. For relatively fine-grained specimens, creep rates increased with the 1.5 power of the applied stress at low stresses and with the third power at high stresses. The results for coarse-grained specimens can, in general, be fit by the cube dependence. The 1.5 power can be reduced to a linear dependence by correcting for an apparent threshold stress, which decreases with increasing temperature. Creep activation energies for YSZ are 128 ± 10 kcal/mol, independent of Y₂O₃ content, impurity level, grain size, and porosity distribution. In addition, over a broad range of temperatures and stresses the absolute values of the steady-state creep rates are influenced only by grain size and O₂ partial pressure.     

Fracture Characteristics of Czochralski-Grown Y3Al5O12

The fracture surfaces of single-crystal Y₃A1₅O₁₂ (YAG) have been examined in detail using differential interference microscopy and atomic force microscopy. In YAG crystals grown in 1977 by the Czochralski method strikingly regular undulations of microscopic and submicroscopic dimensions (4–20 nm in amplitude, 1–20 μm in wavelength) are observed on every fracture surface. The undulations do not exhibit typical characteristics of Wallner lines; furthermore, they are not observed in identical fracture tests for YAG crystals grown in 1990 by the Czochralski method. Transmission electron microscopy reveals that the crystals grown in 1977 exhibit a periodic fluctuation of the ratio of the concentrations of aluminum to yttrium, suggesting that the fracture surface features are caused by periodic astoichiometry.     

Fracture Behavior of Directionally Solidified Y3Al5O12/Al2O3 Eutectic Fiber

The strength and fracture of a directionally solidified Y₃Al₅O₁₂/Al₂O₃ eutectic fiber were investigated. The fiber was grown continuously by an edge-defined film-fed growth technique. The microstructure was characterized using X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The tensile strength and Weibull's modulus of the eutectic fibers were determined in the as-fabricated state and after extended thermal exposure at 1460°C in air. Fractographic analysis was used to identify and classify the strength-limiting mechanisms. The fracture toughness and crack growth behavior were characterized by an indentation technique. A fracture mechanics analysis was also used to establish the relationships between surface flaw size, tensile strength, and fracture toughness of the fiber.     

Rhombohedral Phase in Y2O3-Partially-Stabilized ZrO2

Tetragonal-to-rhombohedral stress-induced phase transformation was studied by X-ray diffraction on the ground surfaces of tetragonal zirconia polycrystals and partially stabilized zirconia containing 2.0 to 5.0 mol% Y₂O₃ prepared by hot isostatic pressing. The rhombohedral phase increased with Y₂O₃ content and also with hot isostatic pressing temperature. The stability of the rhombohedral phase was studied with regard to surface finish and thermal annealing. The subsequent heat treatment of the specimens was found to cause the reverse rhombohedral-to-tetragonal transformation.     

High-Temperature Strength and Fracture Toughness of Y2O3-Partially-Stabilized ZrO2/Al2O3 Composites

The temperature dependence of bending strength, fracture toughness, and Young's modulus of composite materials fabricated in the ZrO₂ (Y₂O₃)-Al₂O₃ system were examined. The addition of A1203 enhanced the high-temperature strength. Isostatically hot-pressed, 60 wt% ZrO₂ (2 mol% Y₂O₃)/40 wt% Al₂O₃ exhibited an extremely high strength, 1000 MPa, at 1000°C.     

High-Temperature Neutron Diffraction of the AlN–Al2O3–Y2O3 System

The importance of aluminum nitride (AlN) stems from its application in microelectronics as a substrate material due to high thermal conductivity, high electrical resistance, mechanical strength and hardness, thermal durability, and chemical stability. Yttria (Y₂O₃) is the best additive for AlN sintering. AlN densifies by a liquid-phase mechanism, where the surface oxide, Al₂O₃, reacts with Y₂O₃ to form an Y-Al-O-N liquid that promotes particle rearrangement and densification. Construction of the phase relations in this multicomponent system is essential for optimizing the properties of AlN. The ternary phase diagram of the AlN–Al₂O₃–Y₂O₃ was developed by Gibbs energy minimization using interpolation procedures based on modeling the binary subsystems. This paper aims at testing the resultant understanding experimentally at selected compositions using in situ high-temperature neutron diffractometry. These experimental results agree with the thermodynamic calculations of AlN–Al₂O₃–Y₂O₃. The ternary phase diagram has been constructed for the first time in this work. High-temperature neutron diffractometry has permitted real time measurement of the reactions involved in this ternary system, especially to determine the temperature range for each reaction, which would have been difficult to establish by other means.     

Effect of Crystallizing the Grain-Boundary Glass Phase on the High-Temperature Strength of Hot-Pressed Si3N4 Containing Y2O3

The effects of fabrication variables on the high-temperature strength of hot-pressed Si₃N₄ containing 5 wt% Y₂O₃ were studied. Materials containing a crystalline grain-boundary phase, formed as a consequence of a high-temperature presintering heat treatment and identified as Si₃N₄·Y₂O₃, had high-temperature strengths significantly superior to those observed for materials containing a glass phase.     

Metastable Phase Formation in Plasma-Sprayed ZrO2 (Y2O3)–Al2O3

Rapidly solidified ZrO₂ (Y₂O₃)–Al₂O₃ powders were prepared by melting fine-particle aggregates in a high-enthalpy plasma flame and then rapidly quenching them in cold water or on a copper chill plate. To ensure complete melting and homogenization of all the particles before quenching, the water-quenching treatment was often repeated two or even three times. The resulting melt-quenched powders and splats displayed a variety of metastable structures, depending on composition and cooling rate. ZrO₂-rich material developed an extended solid solution phase, whereas eutectic material formed a nanofibrous or amorphous structure. Under high cooling rate conditions, the ZrO₂-rich material developed a nanocomposite structure ( t -ZrO₂+α-Al₂O) directly by melt-quenching, whereas, more typically, such a structure was developed only after postannealing of the as-quenched metastable material.     

Film Synthesis of Y3Al5O12 and Y3Fe5O12 by the Spray–Inductively Coupled Plasma Technique

Thin films of yttrium aluminum garnet (YAG, Y₃Al₅O₁₂) and yttrium iron garnet (YIG, Y₃Fe₅O₁₂) were synthesized on single-crystal Al₂O₃ substrates by a modification of spray pyrolysis using a high-temperature inductively coupled plasma at atmospheric pressure (spray–ICP technique). Using this technique, films could be grown at faster rates (0.12 μm/min for YAG and 0.10 μm/min for YIG) than using chemical vapor deposition (0.005–0.008 μm/min for YAG) or sputtering (0.003–0.005 μm/min for YIG). The films were dense and revealed a preferred orientation of (211). The growth of YIG was accompanied by coprecipitation of α-Fe₂O₃. The coprecipitation, however, could be largely suppressed by preliminary formation of a Y₂O₃ layer on the substrate.     

High-Temperature Environmental Stability of the Compounds in the Al2O3–Y2O3 System

Heat treatments in several environments were performed on a series of compounds in the Al₂O₃ and Y₂O₃ system: Al₂O₃Y₃Al₅O₁₂ eutectic, Y₃Al₅O₁₂, YAlO₃, Y₄Al₂O₉, and Y₂O₃. The yttrium aluminates were found to be stable at high temperatures under vacuum and in air. However, when they were heat-treated under vacuum in proximity to SiC, degradation was observed. This was found to be primarily a result of carbothermal reduction. In a similarly reducing environment without Si, the yttrium aluminates, and Al₂O₃ and Y₂O₃, all exhibited degradation by carbothermal reduction. Based upon the experimental results, a degradation mechanism for yttrium aluminates was proposed.     

High-Temperature Phase Relations in the System Gd2O3-Ta2O5

The Phase relations of the system Gd₂O₃-Ta₂O₅ in the composition range 50 to100 mol% Gd2O3 was studied by solidstate reactions at 1350°, 1500°, or 1700°C and by thermal analyses up to the melting temperatures. Weberite-type orthorhombic phase (W2 phase, space group C2221) with the composition of Gd3 TaO7 seems to melt incongruently; at about 2040°C, although this Gd₃TaO₇ Phase was previously reported to melt congruently. A new fluorite-type cubic phase (F phase, space group Fm3m ) was found for the first time above 1500°C in the system. It melts congruently with the composition of about 80mol% Gd2O3at 2318° 3°C. A phase diagram was proposed for the system Gd₂O3–Ta2O₅ in the Gd₂O₃–rich portion