Effect of Hot-Pressing Temperature on Densification and Mechanical Properties of Titanium Diboride with Silicon Nitride as a Sintering Aid

The effect of hot-pressing temperature on the densification behavior and mechanical properties of titanium diboride (TiB₂) was investigated. TiB₂ specimens were hot-pressed for 1 h at temperatures in the range of 1500°–1800°C, with an addition of 2.5 wt% of silicon nitride (Si₃N₄) as a sintering aid. The density increased markedly at temperatures in the range of 1500°–1600°C and remained constant thereafter. The formation of a eutectic liquid at 1550°C was attributed to the steep increase in density. The hot-pressing temperature also improved the mechanical properties, such as the flexural strength, Vickers hardness, and fracture toughness of the specimens. Similar to the density, the mechanical properties improved remarkably at ∼1550°C, so that optimum properties were obtainable at temperatures as low as 1600°C.     

Effect of Iron and Boron Carbide on the Densification and Mechanical Properties of Titanium Diboride Ceramics

The effect of Fe and B₄C on the sintering behavior and mechanical properties of TiB₂ ceramics have been studied. Sintering was performed in an Ar atmosphere at 2000° using attrition-milled TiB₂ powder (mean particle size = 0.8 μm). When a small amount of Fe (0.5 wt%) was added, abnormal grain growth occurred and the sintered density was low. In the case of B₄C added along with 0.5 wt% Fe, however, abnormal grain growth was remarkably suppressed, and the sintered density was increased up to 95% of theoretical. But with excess Fe addition (5 wt%), B₄C grains did not act as a grain growth inhibitor, and B₄C grains were frequently trapped in large TiB₂ grains. The best mechanical properties were obtained for the TiB₂–10 wt% B₄C–0.5 wt% Fe ceramics, which exhibited a three-point bending strength of 400 MPa and a fracture toughness of 5.5 MPa · m^1/2.     

Field-Assisted Sintering of Nanocrystalline Titanium Nitride

Nanosized TiN powder was densified via field-assisted sintering at temperatures of 1150°–1350°C and a pressure of 66 MPa under vacuum. A maximum relative density of ∼97% and a maximum mean grain size of 150–200 nm were obtained. Densification and microstructural evolution have been discussed, in terms of superplasticity and electric-field effects.     

Pressureless Sintering of Boron Carbide

B₄C powder compacts were sintered using a graphite dilatometer in flowing He under constant heating rates. Densification started at 1800°C. The rate of densification increased rapidly in the range 1870°–2010°C, which was attributed to direct B₄C–B₄C contact between particles permitted via volatilization of B₂O₃ particle coatings. Limited particle coarsening, attributed to the presence or evolution of the oxide coatings, occurred in the range 1870°–1950°C. In the temperature range 2010°–2140°C, densification continued at a slower rate while particles simultaneously coarsened by evaporation–condensation of B₄C. Above 2140°C, rapid densification ensued, which was interpreted to be the result of the formation of a eutectic grain boundary liquid, or activated sintering facilitated by nonstoichiometric volatilization of B₄C, leaving carbon behind. Rapid heating through temperature ranges in which coarsening occurred fostered increased densities. Carbon doping (3 wt%) in the form of phenolic resin resulted in more dense sintered compacts. Carbon reacted with B₂O₃ to form B₄C and CO gas, thereby extracting the B₂O₃ coatings, permitting sintering to start at ∼1350°C.     

Aqueous Gelcasting and Pressureless Sintering of Zirconium Diboride Ceramics

Dense (97.3%) zirconium diboride (ZrB₂) ceramics were obtained via gelcasting and pressureless sintering. Four wt% B₄C was used as sintering aid. ZrB₂, SiC, and B₄C can codisperse well in the alkaline region, using a polyacrylate dispersant. Compared with monolithic ZrB₂ (Z), the mechanical properties of ZrB₂‐SiC (ZS) were enhanced. The Vickers hardness and fracture toughness of ZS were (13.1 ± 0.6) GPa and (2.5 ± 0.4) MPa m^1/2, respectively.     

Simultaneous Synthesis and Densification of Titanium Nitride/ Titanium Diboride Composites by High Nitrogen Pressure Combustion

Composites of TiN/TiB₂ were synthesized by a combustion process of BN, Ti in a nitrogen atmosphere. The effect of the BN/Ti ratio and the nitrogen gas pressure on the synthesis of these composites was investigated. Dense TiN/TiB₂ composites with relatively high hardness and toughness were fabricated by combustion synthesis from Ti and BN under a nitrogen pressure of 4.0 MPa. The Vickers microhardness of the products obtained from reactants with a BN/Ti mole ratio of 0.11 increased with an increase in nitrogen pressure and had a maximum value of ∼25 GPa. Fracture toughness, K _IC, of the products increased from 3.1 to 5.9 MPa·m^1/2 as the BN/Ti ratio increased from 0.11 to 0.20. However, products formed under nitrogen pressures higher than 6.0 MPa exhibited circumferential macrocracks due to thermal shock.     

Pressureless Sintering of Titanium Diboride with Nickel, Nickel Boride, and Iron Additives

The effect of relatively small additions (1-5 wt%) of nickel, nickel boride (NiB), and iron to promote the liquid-phase sintering of titanium diboride (TiB₂) has been studied. Carbon also was added to some samples, to reduce the amount of oxygen impurities in the TiB₂ ceramics. Green bodies that were formed by uniaxial pressing were sintered in a graphite furnace at 1300°–1700°C, both under vacuum and in a 500 mbar argon atmosphere, and high densities (>94% of theoretical density) were obtained at temperatures greater than or equal to 1500°C. The weight loss of the samples during sintering was shown to be dependent on the densification rate and the final density and was not governed only by the thermodynamics of the system. Significant exaggerated grain growth was observed in samples with nickel, NiB, and iron during sintering at 1700°C. The exaggerated grain growth was observed to be closely related to the oxygen content of the samples and to temperature. The addition of carbon strongly reduced the density and the oxygen content and, thereby, inhibited grain growth. We have proposed that the exaggerated grain growth is enhanced by surface diffusion in a titanium-oxide-rich layer on the TiB₂ grains.     

Reactive Hot Pressing of Titanium Nitride–Titanium Diboride Composites at Moderate Pressures and Temperatures

Dense composites in the Ti-B-N system have been produced by reactive hot pressing of titanium and BN powders. The effect of the addition of a small amount of nickel (1–3 wt%) on the reaction kinetics and densification of TiN–TiB₂ (40 vol%) composite has been studied. Composites of ∼99% of theoretical density have been produced at 1600°C under 40 MPa for 30 min with 1% nickel. The hardness and fracture toughness of these composites are 24.5 ± 0.97 GPa and 6.53 ± 0.27 MPa·m^1/2, respectively. The microstructural studies on samples produced at lower temperatures indicate the formation of a transient liquid phase, which enhances the kinetics of the reaction and densification of the composite.     

Enhanced Mechanical Properties of Alumina by Dispersed Titanium Diboride Particulate Inclusions

The mechanical properties of composite ceramics composed of 0 to 20 vol% of titanium diboride particles dispersed in an α-alumina matrix were investigated. The alumina–titanium diboride composite powder was hot-pressed at 1470°C for 20 min to achieve over 98.8% of the theoretical composite density. The strength and fracture toughness of the twophase, hot-pressed composite were both significantly improved compared to the single-phase alumina. Results from different methods of measuring the stress intensity factor, ( K _{I c} ) are compared and discussed.     

Processing and Microstructure Development of Titanium Carbide–Nickel Aluminide Composites Prepared by Melt Infiltration/Sintering (MIS)

A combined melt-infiltration/sintering (MIS) route has been described for the preparation of composites that are based on titanium carbide (TiC) with a ductile nickel aluminide (Ni₃Al) binder phase. This approach allows control of the Ni₃Al content, which can be varied readily in the range of 4–25 vol%. Densities of >98% of the theoretical density have been obtained for composites that have been prepared with Ni₃Al contents of ≥8 vol%. Preliminary examination indicates that the infiltration kinetics approximate to parabolic at 1300°C. Compositional analysis of the densified materials indicates only minimal titanium dissolution into the Ni₃Al alloy (<6 at.%), with an analyzed carbide composition of TiC_0.93. Cubic grain-growth kinetics are observed for TiC–16-vol% Ni₃Al, with an activation energy of ∼400 ± 60 kJ/mol.     

Mechanochemical Synthesis and Pressureless Sintering of TiB2–AlN Composites

TiB₂-AlN composites have been fabricated by the pressureless sintering of a mechanochemically processed Ti, Al, and BN powder mixture. TiB₂-AlN powder was obtained from the mixture of Ti, Al, and BN, which had a composition corresponding to 45.7 wt% TiB₂-54.3 wt% AlN, after mechanochemical processing for longer than 24 h. X-ray diffraction and transmission electron microscopy analysis showed that the powder subjected to mechanochemical processing for 60 h consisted of crystallites less than 300 nm in size with a disordered crystal structure. TiB₂-AlN composites with 95% relative density, a flexural strength of 172 MPa, a fracture toughness of 4.6 MPa·m^1/2, a hardness of 12.0 GPa, and an electrical resistivity of 1488 μΩ·cm were obtained by pressureless sintering at 1700°C for 2 h of the powder subjected to mechanochemical processing for 60 h.     

无压烧结氮化硅陶瓷的物理性能研究

以α-Si₃N₄粉末为原料,Y₂O₃和MgAl₂O₄体系为烧结助剂,采用无压烧结方式,研究了烧结温度、保温时间、烧结助剂含量以及各组分配比对氮化硅致密化及力学性能的影响。结果表明:以Y₂O₃和MgAl₂O₄为烧结助剂体系,氮化硅陶瓷在烧结温度为1 600 ℃,保温时间为4 h,烧结助剂含量为12.5%(质量分数),Y₂O₃和MgAl₂O₄质量比为1∶1时,综合性能最好;氮化硅陶瓷显气孔率为0.21%,相对密度为98.10%,抗弯强度为598 MPa,维氏硬度为15.55 GPa。     

Titanium Diboride–Tungsten Diboride Solid Solutions Formed by Induction-Field-Activated Combustion Synthesis

Solid solutions of titanium diboride–tungsten diboride (TiB₂–WB₂) were synthesized by induction-field-activated combustion synthesis (IFACS) using elemental reactants. In sharp contrast to conventional methods, solid solutions could be formed by the IFACS method within a very short time, ∼2 min. Solutions with compositions ranging from 40–60 mol% WB₂ were synthesized with a stoichiometric ratio (Ti + W)/B =½; however, samples with excess boron were also made to counter the loss of boron by evaporation. The dependence of the lattice constants of the resulting solid solutions on composition was determined. The "a" parameter decreased only slightly with an increase in the WB₂ content, whereas the "c" parameter exhibited a significant decrease over the range 40–60 mol% WB₂. Solid-solution powders formed by the IFACS method were subsequently sintered in a spark plasma sintering (SPS) apparatus. After 10 min at 1800°C, the samples densified to relative density 86%. XRD analysis showed the presence of only the solid-solution phase.     

Shrinkage-Free Sintering of Low-Temperature Cofired Ceramics by Loading Dilatometry

Sintering with zero radial shrinkage of low-temperature cofired ceramics (LTCC) was investigated by means of loading dilatometry. The results indicate that constant compressive loads tend to produce either decreased or increased radial shrinkages, and this can vary as a function of density, depending on the magnitude of the applied stresses. Coupling the real-time applied uniaxial load to the radial strain of cylindrical samples afforded a sintering scheme where the radial strain was precisely kept near zero (±0.02%). This approach possibly perfects an existing hot-pressing technique for zero-shrinkage sintering technology of LTCC materials.     

Effect of Heating Rate on the Sintering Behavior and the Piezoelectric Properties of Lead Zirconate Titanate Ceramics

The effect of heating rate on the sintering behavior and the piezoelectric properties of lead zirconate titanate (PZT) ceramics was investigated. Two different types of PZT (pure and doped with Nb₂O₅) were sintered at 1150°C for 2 h with a wide range of heating rate (0.5°–100°C/min). The densification of pure PZT was improved significantly by increasing the heating rate. The improvement was attributed to the suppression of PbO volatilization and grain coarsening during heating. In contrast, the densification behavior of a PZT specimen doped with Nb₂O₅ was not much influenced by the heating rate. These densification behaviors affected the piezoelectric properties of the specimens. The piezoelectric properties of pure PZT were enhanced significantly by increasing the heating rate, while those of doped specimens were improved only moderately.     

Rapid Rate Sintering of Yttria Transparent Ceramics

This paper reports on the influence of rapid rate sintering (RRS) on densification and microstructure evolution of yttria transparent ceramics by using vacuum sintering. The presence of temperature gradient has been confirmed during the RRS process. The higher the heating rate (HR), the larger the temperature gradient in the samples would be. By using RRS, e.g., HR = 40°C/min, the samples could be densified very fast to a relative density of 99.6%. However, these samples could not be further densified, due to the presence of difference in densification caused by a heating rate‐induced temperature gradient. By using a two‐step RRS with an intermediate‐temperature thermal treatment, this problem has been successfully addressed. The intermediate‐temperature treatment allowed for the particle neck growth, so that effective thermal conductivity of the compacts was increased greatly. Therefore, the temperature gradient and differentiate densification were effectively prevented. Samples sintered using the two‐step RRS process could be fully densified and excellent in‐line optical transmittance was achieved. It is believed this strategy is applicable to other transparent ceramics, as well as other engineering ceramics.     

High-Strength Porous Alumina Ceramics by the Pulse Electric Current Sintering Technique

High-strength porous alumina has been fabricated with a microstructure control using the pulse electric current sintering (PECS) technique. During sintering the discharge, which is assumed to take place in the voids between the particles, is thought to promote the bridging of particles by neck growth in the initial stages of sintering, leaving high porosity. The effect of dopants (MgO, 200 ppm; TiO₂, 1000 ppm) and of secondary inclusions (3 vol% 3Y-TZP) on the constrained densification and the improvement in the mechanical behavior of porous alumina ceramics has been reported. The porosity of the fabricated porous alumina was controllable between 30% and 50% depending on the sintering temperature. The flexural strength of alumina having 30% and 42% porosity showed impressive values of 250 and 177 MPa, respectively. The dominance of the preferential neck growth of grains over densification significantly improved the mechanical properties of porous alumina, besides leaving high porosity.     

Fabrication of Dense Nanostructured Silicon Carbide Ceramics through Two-Step Sintering

SiC powder compacts were prepared with Al₂O₃, Y₂O₃, and CaO powders. By two-step sintering, fully dense nanostructured SiC ceramics with a grain sizes of ∼40 nm were obtained. The grain size–density trajectories are compared with those of conventional sintering processes.     

Sintering Behavior and Properties of Iron-Rich Glass-Ceramics

Iron-rich glass-ceramics were obtained by the sintering of two glass powders, labeled G1 and G2, at heating rates of 5° and 20°C/min followed by an isothermal step in the 850°–1050°C temperature interval. The sintering process was evaluated by the linear shrinkage; the closed porosity was estimated by density measurements; the structure and the morphology of the glass ceramics were observed by scanning electron microscopy. The bending strength, the Young modulus, and Vickers hardness of the glass-ceramics materials were evaluated. The results showed that the sintering process and morphology of the glass-ceramics depends on the amount of magnetite and pyroxene formed. With a low percentage of crystal phase formed (25%–30% typical of G1) the structure is characterized by closed porosity; at higher crystallization (45%–50% typical of G2) open porosity is mainly formed. The properties of the glass-ceramics were not influenced by the heating rate but improved with an increase in the degree of crystallization.