共查询到20条相似文献,搜索用时 62 毫秒
1.
杨攀 《制冷与空调(北京)》2020,(3):87-91
本文介绍了常见的并联机组管路振动的原因及其排查方式。针对某型号机组排气管路剧烈振动的问题,对机组结构和排气管路进行实验模态分析,确定机组结构和排气管路发生共振,通过结构优化改变其固有频率,使管路振动值降低。 相似文献
2.
考察汽车传动轴振动特性的指标为1阶约束模态的频率。由此,某商用车传动轴在设计阶段进行模态仿真分析,虽然满足了设计要求,但在整车验证阶段却出现共振,产生了车内共鸣音。针对该问题,改进传动轴模态分析方法,并对传动轴结构进行优化设计,消除共振模态。通过主观评价和噪声测试证实效果良好。 相似文献
3.
通过对客车结构进行合理的简化和等效,在建立了客车主要承载结构的几何模型的基础上,建立了能反映客车结构动态特性的有限元模型。随后对客车的有限元模型进行模态分析,计算出整车结构的固有频率和主要振型,并将模态分析结果与测试结果对比。经过分析,查明了问题客车运行时产生整车共振的原因,为进一步解决客车共振问题提供了可靠的理论依据。 相似文献
4.
5.
6.
针对某消声器筒体与排气管焊接处发生断裂的问题,运用CAE定量分析方法和模态测试分析技术对断裂消声器进行分析研究,并提出将原消声器的排气管贯穿筒体的改进方案。同时对改进前后的消声器进行理论模态和试验模态分析。分析结果表明,改进措施是合理的,提高消声器的工作可靠性。 相似文献
7.
某轿车排气系统振动分析 总被引:3,自引:1,他引:2
联合有限元软件与AVL-Excite软件,对某轿车排气系统进行模态与强迫振动分析。首先利用有限元软件对排气系统做自由模态分析,初步分析其吊耳点布置合理与否。然后利用有限元软件对排气系统进行自由度缩减,提取其质量矩阵、刚度矩阵、主节点自由度信息及模态信息,整合到内燃机-排气系统多体动力学模型中,对排气系统进行受迫振动分析,充分考虑其弹性变形与模态共振对振动响应的影响。得出排气系统任一点上的振动响应及排气管路长度上的振动传递率,考察其振动耦合特性;为排气系统的空间走向和结构设计提供强有力的依据。 相似文献
8.
提出一种基于测点优化与模态扩展的机械结构振动响应全场重构方法。使用D优化设计方法确定最优测点布置方案,根据模态扩展方法构造加速度响应扩展矩阵,从而实现由优化布置的有限测点的加速度响应重构机械结构全场加速度响应,并使用有限元分析软件读取重构的加速度响应,实现机械结构响应全场可视化。开展板结构数值仿真分析和振动响应重构试验,验证了当结构处于多模态共振或非共振状态下机械结构振动响应全场重构方法的有效性和鲁棒性。进一步,通过分析各阶加速度模态贡献量,精准选择主要振动模态分析机械结构的振动响应,实现了基于更少测点的振动响应全场重构。 相似文献
9.
10.
制冷压缩机是决定冰箱、冷柜等家电噪声水平的关键部件。本文首先分析往复式制冷压缩机噪声的类型以及传递途径,指出壳体是压缩机自身噪声向外辐射的最终载体;接着对某一压缩机的壳体进行了模态分析,以了解其固有振动特性;再在压缩机内部的四个支撑机芯的弹簧底部位置和排气管焊接处施加常值幅度的力谱,研究压缩机的受迫振动与声辐射。结果表明:对于此压缩机第1阶弹性变形模态为3kHz左右;四个支撑弹簧和排气管焊接处施加力激励,发现在1kHz以下,壳体的振动小且声辐射效率低,所以声辐射功率也小;随着频率增加,辐射效率提高,特别当超过第1阶变形模态之后辐射效率将大于1,并且此时由于结构模态的不断出现,振动能量和声辐射功率都维持在较大幅度范围内;不同激励点激励起各阶壳体模态振动的有效性不一样,排气管焊接点处比支撑弹簧处能更有效地激励壳体的振动与声辐射。 相似文献
11.
A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling. 相似文献
12.
13.
Liebert A Wabnitz H Grosenick D Möller M Macdonald R Rinneberg H 《Applied optics》2003,42(28):5785-5792
A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue. 相似文献
14.
本文根据多年的实践检定经验 ,参照JJF1 0 59- 1 999《测量不确定度评定与表示》以及《测量不确定度表达 1 0讲》 ,对卧式金属罐容量的测量结果不确定度进行了评定。 相似文献
15.
16.
17.
18.
An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a
rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate
agreement is demonstrated between the derived relations and experimental data. 相似文献
19.
Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995. 相似文献
20.
由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。 相似文献