Frequency-shifted optical feedback in a pumping laser diode dynamically amplified by a microchip laser

Compared with conventional optical heterodyne detection, laser optical feedback imaging (LOFI) allows for a several orders of magnitude higher intensity modulation contrast. The maximum contrast amplification is typically 10(3) for a diode laser in the gigahertz range and 10(6) for a microchip laser in the megahertz range. To take advantage of the wavelength tunability of a laser diode and of the lower resonant detection frequency of a microchip laser, we used LOFI modulation induced by the frequency-shifted optical feedback in a laser diode as a modulated pumping power for a microchip laser for resonant dynamic amplification. In this way, we were able to transfer the optical feedback sensitivity of the laser diode to the megahertz range. Application to telemetry is also reported.     

Glass-fiber self-mixing intra-arterial laser Doppler velocimetry: signal stability and feedback analysis

We have developed a blood velocimeter based on the principle of self-mixing in a semiconductor laser diode through an optical fiber. The intensity of the light is modulated by feedback from moving scattering particles that contain the Doppler-shift frequency. Upon feedback the characteristics of the laser diode change. The threshold current decreases, and an instable region may become present above the new threshold. The amplitude of the Doppler signal turns out to be related to the difference in intensity between situations with and without feedback. This amplitude is highest just above feedback. The suppression of reflection from the glass-fiber facets is of paramount importance in the obtaining of a higher signal-to-noise ratio. Using an optical stabilization of the feedback, we optimized the performance of the laser-fiber system and the Doppler modulation depth and clarified its behavior with a suitable physical model. We also investigated the effect of the finite coherence length of the laser. We tested the efficiency of the self-mixing velocimeter in vivo with the optical glass fiber inserted in the artery with endoscopic catheters, both in upstream and in downstream blood flow conditions. For the latter we used a special side-reflecting device solution for the fiber facet to allow downstream measurements.     

Quantitative Analysis of Trace Moisture in N(2) and NH(3) Gases with Dual-Cell Near-Infrared Diode Laser Absorption Spectroscopy

This paper demonstrates our optical measurement system based on near-infrared tunable diode laser absorption spectrometry and reports the results of trace moisture determination in nitrogen and ammonia gases. A near-infrared InGaAsP distributed feedback diode laser operating at room temperature was employed as the optical source. We used a dual-cell detection strategy to cancel common mode noise from the diode laser and remove the effect of the residual moisture absorption in the beam path outside the sample cell. We also used this method to successfully eliminate the interfering absorption of matrix gas molecules such as NH(3). The detection limit of H(2)O absorption of 4 ppb in nitrogen and 12 ppb in ammonia was obtained using a single-pass absorption cell of only 92 cm in length and the average results of 10 scan measurements. This system has characteristics of both the high sensitivity and capability of in situ and real-time measurement.     

Laser optical feedback imaging insensitive to parasitic optical feedback

We present an optical architecture for the laser optical feedback imaging (LOFI) technique that makes it possible to avoid the effect of the optical parasitic reflections introduced by the optical components located between the laser source and the studied object. These reflections damage phase and amplitude information contained in the images. This phenomenon is a leading problem that strongly limits the LOFI performance for weak feedback detection. Consequently, it is essential to be able to limit or avoid the effect of these parasitic reflections to reach the optimal LOFI performance.     

High-frequency intensity modulation in orthogonal polarized dual frequency lasers with optical feedback

High-frequency modulation of laser output intensity is studied with asymmetric feedback induced by the misalignment of an external feedback reflector in an orthogonal polarized dual frequency laser. The fringe frequency of the optical feedback system is seven times higher than that of a conventional optical feedback system, due to multiple feedback effects. The output characteristics of two orthogonal polarized modes are also investigated. Mode competition is observed between the two modes. When initial intensities of the two modes are unequal, the mode competition will be strong. The difference in initial intensity between the two orthogonally polarized modes plays an important role in the mode competition with optical feedback. Experimental results are presented, as well as a theoretical explanation. The high-frequency modulation of laser intensity can greatly increase the resolution of an optical feedback sensing system.     

Effects of unwanted feedback on synchronized chaotic optical communications

The effects of unwanted external optical feedback on synchronized chaotic optical communication systems are studied numerically. We consider an open-loop configuration consisting of a transmitter laser with double external optical feedbacks and a receiver laser with optical injection from the transmitter laser. First, including the effects of unwanted optical feedback, the synchronization performances of both the complete synchronization and the generalized synchronization are examined. Then the encoding and decoding performances of the generalized synchronization and the effects of the introduced feedback are investigated, respectively. Finally, we study the control of the unwanted feedback on the dynamics of the transmitter laser and briefly discuss the system security when the transmitter laser is driven to operate in a steady state or periodic oscillation state by the additional feedback.     

Laser diode facet modal reflectivity measurements

A simple and accurate method for measuring the front facet modal reflectivity of a Fabry-Perot laser diode is presented. In this method, optical feedback from an external mirror of known reflectivity, R(ext), is used to alter the laser diode threshold current. The effect of the external mirror and front facet reflectivities on the threshold current then allows for a measurement of the front facet modal reflectivity of the laser diode and is theoretically and experimentally studied. This method was used to measure a facet reflectivity of R(2) = 0.0151(+0.0018/-0.0032) [R(2) = 0.00592(+0.00085/-0.00123)] for a commercially antireflection-coated facet of a laser diode with a center wavelength of 795 nm (935 nm). The results of the reflectivity measurements based on the threshold current as a function of the external mirror reflectivity are compared with the results of the reflectivity measurements based on modulation depth of the optical spectrum [IEEE J. Quantum Electron. QE-19, 493 (1983)].     

Detection of cortical activation with time-resolved diffuse optical methods

Simulations based on diffusion theory that use a finite-element method and rely on an magnetic resonance imaging head model suggest that time-resolved diffuse optical techniques could provide information about the depth at which variations in perfusion take place and improve the detection of cortical activation. Experimental investigations were performed with sequentially driven picosecond laser diodes and an eight-channel time-correlated single-photon-counting detection system. The experimental results obtained for activation in the motor cortex, and for the Valsalva maneuver, confirm our assumptions and are in good agreement with the simulated data.     

Spatial beam profiles from a laser-diode system with optical feedback: the importance of interference

The output beam profile of a laser diode with weak-to-moderate levels of optical feedback is shown to arise from interference of the emitted and feedback fields. This has been determined from a series of experiments, that measure the output spatial beam profile as the optical feedback field into the laser diode is spatially manipulated. Tilting, focusing, and aperturing the feedback field led to output beam profiles readily interpreted as the interference between the emitted and the feedback fields, provided the output of the laser-diode system with optical feedback has sufficient temporal coherence. Observation of the interference pattern in the spatial beam profile, at an appropriate level of optical feedback, can be used to study the relative wave front of the optical feedback and emitted fields and to estimate coupling coefficients.     

Subtle effects of the substrate in optical disk data storage systems

Much attention has been focused on the effects of the disk substrate in optical data storage. In particular, substrate birefringence has been studied extensively because it causes significant problems in magneto-optic systems. We investigate certain subtle effects of the substrate, such as feedback into the laser diode, in compact disk and phase-change systems. Our analysis of the compact disk system led us to discover a new technique for the rapid measurement of the substrate birefringence. We also address the question of how focusing the laser beam through the substrate will affect the depth of focus.     

Experimental comparison of autodyne and heterodyne laser interferometry using an Nd:YVO₄ microchip laser

Using an Nd:YVO? microchip laser with a relaxation frequency in the megahertz range, we have experimentally compared a heterodyne interferometer based on a Michelson configuration with an autodyne interferometer based on the laser optical feedback imaging (LOFI) method regarding their signal-to-noise ratios. In the heterodyne configuration, the beating between the reference beam and the signal beam is realized outside the laser cavity, while in the autodyne configuration, the wave beating takes place inside the laser cavity, and the relaxation oscillations of the laser intensity then play an important part. For a given laser output power, object under investigation, and detection noise level, we have determined the amplification gain of the LOFI interferometer compared to the heterodyne interferometer. LOFI interferometry is demonstrated to show higher performance than heterodyne interferometry for a wide range of laser powers and detection levels of noise. The experimental results are in good agreement with the theoretical predictions.     

Polarized differential-phase laser scanning microscope

A polarized differential-phase laser scanning microscope, which combines a polarized optical heterodyne Mach-Zehnder interferometer and a differential amplifier to scan the topographic image of a surface, is proposed. In the experiment the differential amplifier, which acts as a PM-AM converter in the experiment, converting phase modulation (PM) into amplitude modulation (AM). Then a novel, to our knowledge, phase demodulator was proposed and implemented for the differential-phase laser scanning microscope. An optical grating (1800 lp/mm) was imaged. The lateral and the depth resolutions of the imaging system were 0.5 mum and 1 nm, respectively. The detection accuracy, which was limited by the reflectivity variation of the test surface, is discussed.     

Optical time-domain reflectometry in optical fiber with reflection delay time matched to the period of the optical frequency modulation

A method of optical time-domain reflectrometry in optical fiber is described that uses a single distributed feedback diode laser and a reference reflector. When the period of the frequency modulation of the laser matches the time difference between the reference reflection and the reflection of interest an increase in the noise at the detector occurs. The locations of reflections within the fiber are then mapped to frequencies at which the noise at the detector increases. A sinusoidal frequency modulation is analyzed, and an experiment is described in which the system is used to measure the location and the wavelength of two Bragg gratings located 10 cm apart in an optical fiber. Wavelength measurement is accomplished by temperature tuning the diode laser.     

大视场激光探测与告警技术

利用四路红外非制冷焦平面探测器、大视场光学系统、窄带滤光片和信号处理系统,构成了凝视成像激光探测与告警系统。光学系统采用三片式结构的广角镜头来实现大视场;使用先进的非球面光学设计技术,并以FPGA完成探测器响应信号的非均匀校正,以改善像质;通过光学系统的畸变校正,提高激光的探测方向精度;利用激光和背景强度之间的反差,通过激光目标检测算法进行告警。实验表明,该系统能在127视场范围内对波长为1.315靘, 2.7靘, 3.8靘, 10.6靘的4种激光进行告警,探测功率密度范围为0.05 ~50mW/cm2,探测方向精度可达1。     

圆柱类金属构件表面裂纹的激光超声识别方法研究

为了利用激光超声技术有效地识别圆柱表面裂纹,提出利用圆柱表面波信号增强和小波包-奇异值分解(WPT-SVD)方法识别圆柱类金属构件表面裂纹的位置和深度。建立了圆柱的激光超声显式有限元模型,分析了圆柱表面裂纹对表面波的模式转化作用。利用圆柱表面裂纹在激发源位置附近时激光超声扫描信号增强的现象,识别圆柱表面裂纹的位置。在已识别圆柱表面裂纹位置的基础上,通过分析圆柱表面裂纹检测信号的时频特点,利用WPT-SVD提取圆柱表面信号的时频特征,定义参数k r表征裂纹深度的变化,识别圆柱表面裂纹深度。搭建了激光超声圆柱表面裂纹检测实验系统,开展了实验研究,实验结果表明所提出的圆柱表面信号增强和WPT-SVD方法可以识别出圆柱表面裂纹的位置和深度。     

High frequency ultrasound imaging with optical arrays

Dynamically focused and steered high frequency ultrasound imaging systems require arrays with fine element spacing, wide bandwidths, and large apertures. However, these characteristics are difficult to achieve at frequencies greater than 30 MHz using conventional array construction methods. Optical schemes offer a solution. Focused laser beams incident on a suitable surface can generate and detect acoustic radiation. Precisely controlling the position and size of the beams defines points of transmission and detection, making it possible for pulse-echo image formation by synthetic aperture methods. An optical detection array was built, relying on a conventional piezoelectric transducer as an ultrasound source. The detection system, with near optimal resolution over a wide depth of field, demonstrates the potential for high frequency array implementation using optical techniques. A possible application is in pathology, where 2-D or 3-D fine resolution pulse-echo imaging can be performed in situ without the need for biopsies.     

Absolute distance measurement with heterodyne optical feedback on a Yb:Er glass laser

Absolute distance measurement based on optical feedback using a single-frequency Yb:Er glass laser is demonstrated via the combination of heterodyne detection and frequency sweep. The technique allows for the enhancement of the sensitivity of the laser response to self-mixing thanks to resonant excitation close to the relaxation-oscillation frequency peak. The experimental results on noncooperative targets are in good agreement with the theory, and the shape of the resulting signal is analyzed in both the temporal and the frequency domains considering the specific dynamic of the class B solid-state laser. Suggestions are provided for further improvements on the signal processing.     

Performance comparison of an all-fiber-based laser Doppler vibrometer for remote acoustical signal detection using short and long coherence length lasers

All-fiber laser Doppler vibrometer systems have great potential in the application of remote acoustic detection. However, due to the requirement for a long operating distance, a long coherence length laser is required, which can drive the system cost high. In this paper, a system using a short coherence length laser is proposed and demonstrated. Experimental analysis indicates that the multi-longitudinal modes of the laser cause detection noise and that the unequal length between two paths (local oscillator path and transmission path) increases the intensity and the frequency components of the noise. In order to reduce the noise, the optical length of the two paths needs to be balanced, within the coherence length of the source. We demonstrate that adopting a tunable optical delay to compensate the unequal length significantly reduces the noise. In a comparison of the detection results by using a short coherence laser and a long coherence laser, our developed system gives a good performance on the acoustic signal detection from three meters away.     

Automatic alignment-control system for a suspended Fabry-Perot cavity

In interferometric gravitational-wave detectors, most of the optical components are suspended by wires so that they are isolated from all kinds of forces except gravity. The requirement for the alignment of optical components to the laser beam is crucial. We have demonstrated a servo system developed for a Fabry-Perot cavity whose mirrors are suspended independently. We use mechanical modulation and a lock-in detection method to detect any misalignment. This system directly detects the relation between the axis of the laser beam and the axis of the cavity and automatically aligns the cavity to the laser beam. We confirmed that the intensity of the reflected light from the suspended Fabry-Perot cavity can be minimized with this system. Automated control of the alignment of the large-scale detectors is also discussed.     

Analysis of the effects of feedback asymmetry in external cavity He-Ne lasers

A theoretical analysis of the characteristics of an external cavity He-Ne laser with asymmetric feedback induced by the misalignment of an external feedback mirror is proposed. The theoretical model considers both the multiple reflections and the phase variation caused by the asymmetric external cavity. It is found that the phase variation is of importance in determining the effects of asymmetric feedback. The three-order asymmetric feedback effects are experimentally observed and can be interpreted well by this model. The fringe frequency of the asymmetric optical feedback system can also be increased. The experimental results are in good agreement with the theoretical analysis. The theoretical and experimental results offer a potential increase in the resolution of an optical feedback system with asymmetric feedback.