Nanocrystalline anatase TiO2 prepared via a facile low temperature route

Nanocrystalline anatase TiO₂ was prepared by a facile sol-gel route at a temperature of 65 °C under mild conditions. Tetrabutyl titanate was used as a titanium precursor, glacial acetic acid was used as an inhibitor, and anhydrous ethanol was used as a solvent. XRD, TEM, FT-IR and XPS spectra were applied to characterize the crystal phase, microstructure, and other physicochemical properties of the nanoanatase TiO₂. The results showed that as prepared ellipse-shaped anatase TiO₂ with an average diameter of 7 nm, which is rich in surface hydroxyl groups, was found to exhibit high dispersibility.     

In-situ preparation of TiO2/SnO2 nanocrystalline sol for photocatalysis

A novel preparation method to synthesize TiO₂/SnO₂ nanocrystalline sol under mild conditions was presented. Ti(OC₄H₉)₄ used as a precursor was hydrolyzed in the rutile SnO₂ nanocrystalline sol, and in-situ formed TiO₂/SnO₂ nanocrystalline sol. The crystal structure, morphology and photocatalysis performance of samples were investigated. The results show that the additional rutile SnO₂ nano grains serve as heterogeneous crystal nucleus and exhibite the inducing effect on TiO₂ grains growth, thus leading to the changes in crystalline phase and particle morphology. In addition, the photoluminescence (PL) spectra analysis indicates that TiO₂/SnO₂ composite structure induces a better charge separation, and thus the photocatalytic activity of TiO₂/SnO₂ sol is increased significantly compared with TiO₂ sol.     

SiO2/TiO2 multilayer films grown on cotton fibers surface at low temperature by a novel two-step process

A novel two-step process was developed to synthesize and deposit SiO₂/TiO₂ multilayer films onto the cotton fibers. In the first step, SiO₂ particles on cotton fiber surface were synthesized via tetraethoxysilane hydrolysis in the presence of cotton fibers, in order to protect the fibers against photo-catalytic decomposition by TiO₂ nanoparticles. In the second step, the growth of TiO₂ nanoparticles into the modified cotton fiber surface was carried out via a sol-gel method at the temperature as low as 100 °C. The as-obtained SiO₂/TiO₂ multilayer films coated on cotton fibers were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, atomic force microscopy and X-ray diffraction, respectively.     

Influence of metal plasma ion implantation on photo-sensitivity of anatase TiO2 thin films

Nano-scale TiO₂ thin films were synthesized by using sol-gel and spin-coating techniques on glass substrates for photo-catalytic applications. The Ti(IV) butoxide-based TiO₂ thin films were optimized for transforming into the high-purity crystalline anatase phase when calcined at 500 °C. To further enhance the photo-catalysis sensitivity of TiO₂ thin films for use in visible light environments, a metal plasma ion implantation process was implemented to modify the band gap electron configuration of Ti. Various transition metal atoms such as Ni, Cu, V, and Fe were ionized and accelerated at 20 keV to impinge on the surface of TiO₂ substrates at a dosage of 5 × 10¹⁵ ions/cm². ESCA analysis confirmed the binding energy shift of Ti by 0.8-1.2 eV, which accounted for the increased effective positive charge of Ti, resulting in more effective electron trapping capability and, thus, the electron-hole pair separation. In addition, the absorption spectroscopy demonstrated that optical absorption in the visible light regime occurred in specimens implanted with transition metal ions, likely due to the formation of extra impurity energy levels within the original TiO₂ band gap energy structure. Among all tested implant materials, the band gap energy of TiO₂ was effectively reduced by Cu and Fe ion implantation by 0.9-1.0 eV, which was sufficient enough to excite valence electrons over the band gap in visible light environments. The feasibility of the metal-doped TiO₂ thin films for effective applications under visible light irradiation was further confirmed by using super-hydrophilicity contact-angle measurement.     

Facile synthesis of rice-like anatase TiO2 nanocrystals

Rice-like anatase TiO₂ nanocrystals have been synthesized by hydrothermal treating Ti(OH)₃ precursor in deionized water, which is easy to form in-situ a stable TiO₂ aqueous dispersion and no post-synthetic purification process is required. The influences of synthetic parameters, such as reaction time and pH value, on the morphologies of the resulting nanocrystals have been investigated. It is found that the crystallinity and sizes of TiO₂ nanocrystals increase with the reaction time increased. The pH value is important for controlling the sizes and shapes of TiO₂ nanocrystals. As pH value increases from 2 to 11, spherical, rice-like, and rod-like TiO₂ nanocrystals are obtained, respectively. The formation mechanism of rice-like anatase TiO₂ nanocrystals is supposed to be a hydrothermal crystallization and Ostwald ripening process.     

Microstructure and photocatalytic activity of mesoporous TiO2 film coated on an aluminum foam

A TiO₂ film was synthesized via a surfactant assisted sol-gel process and dip-coated on the surface of an open-celled aluminum foam. The film shows a typical mesoporous structure composed of anatase crystalline grains with the average size of 10 nm, and has the thickness of about 3.5 μm as well as the BET surface area of 78.1 m²/g. It exhibits high photocatalytic efficiency toward the decomposition of formaldehyde at continuous flow mode. The relatively small grain size of TiO₂ and relatively thick mesoporous structure, which is favorable for high photochemical activity and the mass transfer of the reactants, should be responsible for the properties.     

One-pot synthesis of intestine-like SnO2/TiO2 hollow nanostructures

In the present study the intestine-like binary SnO₂/TiO₂ hollow nanostructures are one-pot synthesized in aqueous phase at room temperature via a colloid seeded deposition process in which the intestine-like hollow SnO₂ spheres and Ti(SO₄)₂ are used as colloid seeds and Ti-source, respectively. The novel core (SnO₂ hollow sphere)-shell (TiO₂) nanostructures possess a large surface area of 122 m²/g (calcined at 350 °C) and a high exposure of TiO₂ surface. The structural change of TiO₂ shell at different temperatures was investigated by means of X-ray diffraction and Raman spectroscopy. It was observed that the rutile TiO₂ could form even at room temperature due to the presence of SnO₂ core and the unique core-shell interaction.     

碳纳米管修饰LaFeO3/TiO2复合材料的光催化性能与机理

采用超声辅助溶胶凝胶法制备了LaFeO₃颗粒,进一步以碳纳米管(CNTs)为基底和钛酸丁酯为前体,通过一步水热法煅烧合成CNTs/TiO₂/LaFeO₃(CTF)三元异质结光催化复合材料。通过扫描电子显微镜(SEM)、X射线衍射分析(XRD)、氮气吸附-解吸等温线(BET)、紫外-可见分光光度计(UV-Vis)、光致发光光谱(PL)等表征手段对材料的形貌与特征结构、比表面积和孔径结构以及光学特征进行了分析,并在紫外光下通过降解活性黑五(RB5)测试样品的光催化性能。结果表明,以CNTs作为载体,能够有效提升LaFeO₃/TiO₂复合材料的光催化性能。当CNTs在复合材料中的质量占比为5%时,150 W汞灯照射下RB5的50 min去除率可达99.5%。CNTs一方面通过增加复合材料的比较面积为催化反应的进行提供了更多的活性位点,更为重要的是,CNTs作为光生载流子传输的通道加快了电荷分离效率,提升了复合材料的降解能力和催化反应动力学进程。     

Preparation and characterization of TiO2/polystyrene core-shell nanospheres via microwave-assisted emulsion polymerization

A combined procedure of sol-gel and microwave-assisted emulsion polymerization has been developed to prepare TiO₂/polystyrene core-shell nanospheres with nano-scale TiO₂ core and smooth and well-defined polystyrene shell. The core-shell structure and morphology were examined by TEM. The diameter and its distribution of the nanospheres were measured by dynamic light scattering. The nanospheres were characterized with Fourier transform infrared spectroscopy (FTIR). It is found that the diameter and its distribution of the TiO₂/polystyrene core-shell nanospheres can be regulated by the concentration of styrene monomer in the emulsion solution.     

DNA-like dye-sensitized solar cells based on TiO2 nanowire-covered nanotube bilayer film electrodes

This paper reports a two-step formation of a TiO₂ nanowire-covered nanotube bilayer film technique and its application in DNA-like dye-sensitized solar cells. The bilayer film was prepared by the electrochemical anodization first and then the hydrothermal method. From the reflectivity spectrum and scanning electron microscopy it is observed that the nanowire layer on the top cannot only decrease the reflectivity of the film, but also play a role to modify the film cracks. Compared with the dye-sensitized solar cells based on a single layer electrode, the cell with the bilayer film showed higher photovoltaic parameters and a lower dark current, which is due to its higher light harvesting efficiency and lower charge recombination between the electrolyte and the substrates.     

The role of the TiO2 nanotube array morphologies in the dye-sensitized solar cells

Arrays of TiO₂ nanotubes were fabricated by the anodization of Ti foils and then used in assembling dye-sensitized solar cells (DSSCs). The role of the morphologies of the TiO₂ nanotubes in the photovoltaic performances of the DSSCs was studied in terms of the surface topography and the tube length. The necessity of removing the nanoporous films from the surface of the nanotube arrays for good DSSC performance has been demonstrated. Also, it has been shown that appropriately increasing the tube length was an effective measure for enhancing both the short-circuit current density and the conversion efficiency of the DSSCs.     

Superhydrophilic anatase TiO2 film with the micro- and nanometer-scale hierarchical surface structure

Nanosized anatase TiO₂ film on the ITO glass has been fabricated via spin coat process, with sodium dodecylbenzenesulfonate modified TiO₂ nanoparticles, which is synthesized by a sol-hydrothermal method, and also characterized mainly by means of field emission scanning electron microscopy (FESEM). The results show that the as-prepared anatase TiO₂ film exhibits superhydrophilic characteristic although it is not exposed to ultraviolet irradiation. The high roughness resulting from hierarchical surface structure is responsible for its superhydrophilicity. This work would provide a new route to fabricate newly nanostructured semiconductor films.     

Electrochromic properties of TiO2 anatase thin films prepared by a dipping sol-gel method

Electrochromic TiO₂ anatase thin films on ITO were prepared by the sol-gel dipping method using a solution of titanium tetraisopropoxide, diethanolamine and ethanol. The films were transparent in the visible range and can be colored in a solution of LiClO₄ in propylene carbonate. The transmittances of the colored films were found to be strongly dependent on the Li⁺ inserted charge. Combining the experimental data obtained from in situ Raman and in situ transmittance spectra with the data from chronoamperometic measurements, it was demonstrated that the fully colorated state of the TiO₂ anatase films is Li_0.5TiO₂ with a crystalline structure of Imma space group symmetry. In the Raman spectra this coloration state exhibits five characteristic bands at 176, 224, 316, 531 and 629 cm⁻¹.     

Effect of TiO2-SiO2 sol-gel coating on the cpTi-porcelain bond strength

The effects of TiO₂-SiO₂ sol-gel coating with different firing temperatures (300 °C, 500 °C, and 750 °C) on the cpTi-porcelain bond strength were investigated in the present study. Prior to applying the low-fusing dental titanium porcelain, the phase, surface morphology, surface roughness and static water contact angle of the intermediate layer were evaluated. The cpTi-porcelain bond strength was measured using the three-point flexure test according to ISO 9693 standard. Statistical analyses were made using one-way ANOVA and Dunnett-t test. Significantly higher bond strength of TiO₂-SiO₂/750 °C (specimens coated with TiO₂-SiO₂ sol-gel coating and fired at 750 °C for 1 h) when compared to the control group was observed (p < 0.05). No rutile phase was found in all the tested specimens coated with TiO₂-SiO₂ sol-gel coating. The surface morphology of the intermediate layer was apparently different with different firing temperatures. It was found that the static water contact angle of TiO₂-SiO₂/750 °C significantly decreased (p < 0.05). However, no markedly different R_a of TiO₂-SiO₂/500 °C and TiO₂-SiO₂/750 °C in comparison to that of the control group was observed (p > 0.05). The results show that the TiO₂-SiO₂ sol-gel coating fired at 750 °C for 1 h can notably improve the cpTi-porcelain bond strength and may be suitable for clinical use.     

Molecular recognitive photocatalytic decomposition on mesoporous silica coated TiO2 particle

Mesoporous silica coated titania exhibited a substrate selective photocatalytic reaction; 4-nonylphenol and phenol were decomposed while nonane was not decomposed by the UV irradiation to their aqueous mixture.     

Determination of photo-catalytic activity of un-doped and Mn-doped TiO2 anatase powders on acetaldehyde under UV and visible light

Titanium dioxide (TiO₂) photocatalytic powder materials doped with various levels of manganese (Mn) were synthesized to be used as additives to wall painting in combating indoor and outdoor air pollution. The heterogeneous photocatalytic degradation of gaseous acetaldehyde (CH₃CHO) on Mn-TiO₂ surfaces under ultraviolet and visible (UV/Vis) irradiation was investigated, by employing the Photochemical Static Reactor coupled with Fourier-Transformed Infrared spectroscopy (PSR/FTIR) technique. Experiments were performed by exposing acetaldehyde (~ 400 Pa) and synthetic air mixtures (~ 1.01 × 10⁵ Pa total pressure) on un-doped TiO₂ and doped with various levels of Mn (0.1-33% mole percentage) under UV and visible irradiation at room temperature. Photoactivation was initiated using either UV or visible light sources with known emission spectra. Initially, the photo-activity of CH₃CHO under the above light sources, and the physical adsorption of CH₃CHO on Mn-TiO₂ samples in the absence of light were determined prior to the photocatalytic experiments. The photocatalytic loss of CH₃CHO on un-doped TiO₂ and Mn-TiO₂ samples in the absence and presence of UV or visible irradiation was measured over a long time period (≈ 60 min), to evaluate their relative photocatalytic activity. The gaseous photocatalytic end products were also determined using absorption FTIR spectroscopy. Carbon dioxide (CO₂) was identified as the main photocatalysis product. It was found that 0.1% Mn-TiO₂ samples resulted in the highest photocatalytic loss of CH₃CHO under visible irradiation. This efficiency was drastically diminished at higher levels of Mn doping (1-33%). The CO₂ yields were the highest for 0.1% Mn-TiO₂ samples under UV irradiation, in agreement with the observed highest CH₃CHO decomposition rates. It was demonstrated that low-level (0.1%) doping of TiO₂ with Mn results in a significant increase of their photocatalytic activity in the visible range, compared to un-doped TiO₂. This elevated activity is lost at high doping levels (1-33%). Finally, the photocatalytic degradation mechanism of CH₃CHO on 0.1% Mn-TiO₂ surfaces under visible irradiation leading to low CO₂ yields is different than that under UV irradiation resulting to high CO₂ yields.     

Structural investigations on TiO2 and Fe-doped TiO2 nanoparticles synthesized by laser pyrolysis

Undoped and Fe-doped TiO₂ nanopowders with Fe/Ti (atomic ratio) precursor concentration ranging from 7% up to 25% have been prepared by the IR laser pyrolysis technique. A sensitized mixture of TiCl₄ and Fe (CO)₅ was used as titanium and iron precursor, respectively. Reference undoped titania samples with a major concentration of anatase phase (about 90%) were obtained by the same technique by using very high flows of the oxidizing agent (air). The effects of the iron-dopant concentration on the essential structural properties of the resultant powders such as the phase formation, the crystallinity, the average particle size and distributions were systematically investigated by X-ray diffraction, Raman spectroscopy and transmission electron microscopy. The decrease of the TiO₂-anatase crystalline phase, the simultaneous increase of the amorphous phase and the decrease in size of particle mean diameter appear as main effects induced by the Fe-dopant concentration.     

Large-scale synthesis and characterization of fan-shaped rutile TiO2 nanostructures

Large-scale fan-shaped rutile TiO₂ nanostructures have been synthesized by means of a simple hydrothermal method using only TiCl₄ as titanium source and chloroform/water as solvents. The physicochemical features of the fan-shaped TiO₂ nanostructures are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), nitrogen absorption-desorption, diffuse reflectance ultraviolet-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). Structural characterization indicates that the fan-shaped TiO₂ nanostructures are composed of several TiO₂ nanorods with diameters of about 5 nm and lengths of 300-350 nm. The average pore size and BET surface area of the fan-shaped TiO₂ nanostructures are 6.2 nm and 59 m²/g, respectively. Optical adsorption investigation shows that the fan-shaped TiO₂ nanostructures possess optical band gap energy of 3.11 eV.     

Fabrication of photocatalytic heat-mirror with TiO2/TiN/TiO2 stacked layers

The photocatalytic heat-mirror based on TiO₂/TiN/TiO₂ stacked layers is prepared by reactive magnetron sputtering on quartz substrates under substrate-heating condition. We find that the addition of a thin Ti interlayer between the TiN and the outer TiO₂ layers drastically improves the heat-insulating performance. This type of stacked layer also exhibits higher photocatalytic activity for decomposition of acetaldehyde gas, compared with a TiO₂ single layer. The optical property of the TiN in TiO₂/TiN/TiO₂ stacked layers is the key not only revealing excellent heat-insulating effect but also improving the photocatalytic performance of the outer TiO₂ layers in the stacked layers.