Heat‐sealing properties of soy protein isolate/polyvinyl alcohol film made compatible by glycerol

Heat‐sealing properties are necessary for packaging materials. Soy protein isolate/polyvinyl alcohol (SPI/PVA) blend film is a biodegradable potential packaging material. We analyzed the effects of PVA content (0–20%), glycerol content (1–3%), and sealing temperature (180–230°C) on the heat‐sealing properties of SPI/PVA blend film. Results showed that SPI/PVA film obtained the desired sealing properties when the PVA content exceeded 15%. The sealing strength increased with the PVA content, reaching a maximum upon blending with 20% PVA and 1% glycerol at 220°C. The temperature at sealing strength was approximately twice that at 180°C. However, glycerol migrated to the surface and hindered the entanglement of macromolecular chains in the sealing interface, thereby resulting in reduction of seal strength. Glycerol vaporization at 204°C led to aesthetically unacceptable blistering in the sealing area. Therefore, the optimum sealing temperature of the blended film was ～200°C. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40308.     

Pervaporation separation of water‐isopropyl alcohol mixtures with blend membranes of sodium alginate and poly(acrylamide)‐grafted guar gum

The blend membranes of sodium alginate (Na‐Alg) and poly(acrylamide)‐grafted guar gum (PAAm‐g‐GG) in the ratios of 3:1 and 1:1 were prepared and studied for the pervaporation separation of water–isopropyl alcohol mixtures over the entire range of mixture composition at 30°C. Membranes prepared from neat Na‐Alg (M‐1) and the 1:1 blend of Na‐Alg and PAAm‐g‐GG (M‐3) showed the highest separation selectivity for 10 mass % water in the feed mixture, whereas membranes prepared with the 3:1 blend ratio of Na‐Alg to PAAm‐g‐GG showed the highest separation selectivity of 20 mass % water in the feed. Selectivity decreased with increasing amount of water in the feed for all the membranes, but these values show an increase with increasing amount of grafted copolymer in the blend mixture. Flux increased with increasing amount of water in the mixture, but the flux values did not change markedly with the PAAm‐g‐GG content in the blend membrane at the lower mass % water. At higher mass % of water, the flux values of the blends increase systematically with increasing amount of PAAm‐g‐GG in the blend polymer. For the 10 mass %‐containing binary mixtures, the pervaporation separation experiments were performed at 30, 40, and 50°C, and the resulting data were used to calculate the Arrhenius activation parameters. These data indicated activated pore‐type diffusion of the permeants in the membranes. Dynamic sorption studies were also performed on up to 40 mass % water–isopropyl alcohol mixtures at 30°C. These results, when analyzed by the empirical equation, indicated Fickian transport in all the cases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2014–2024, 2002     

Synthesis and characterization of maleated ionomers via ring‐opening reaction of epoxidized styrene‐butadiene rubber with potassium hydrogen maleate and study of their behavior as compatibilizer

A novel method for synthesizing maleate ionomer of (styrene‐co‐butadiene) rubber (SBR) from epoxidized SBR was developed. The epoxidized SBR was prepared via epoxidation of SBR with performic acid formed in situ by H₂O₂ and formic acid in cyclohexane. The maleated ionomer was obtained by ring‐opening reaction of the epoxidized SBR solution with an aqueous solution of potassium hydrogen maleate. The optimum conditions were studied. It was found that it is necessary to use phase transfer catalyst and ring‐opening catalyst for enhancing the epoxy group conversion. To obtain 100% conversion addition of dipotassium maleate is important. The product was characterized by FTIR spectrophotometry and transmission electron microcroscopy (TEM). The results showed that the product was really an ionomer with domains of maleate ionic groups. Some properties of the ionomer, such as water absorbency, oil absorbency and dilute solution behavior were studied. With increasing ionic groups, the water absorbency of the ionomer increases, whereas the oil absorbency decreases. The dilute solution viscosity of the ionomer increases abruptly with increasing ionic group content. The ionomer can be used as a compatibilizer for the blends of SBS and chlorosulfonated polyethylene (CSPE). Addition of a small amount of the ionomer to the blend can enhance the mechanical properties of the blends. 3 wt % ionomer based on the blend can increase the tensile strength and ultimate elongation of the blend nearly twice. The compatibility of the blends enhanced by adding the ionomer was shown by scanning electron microscopy. The blend of equal parts of SBS and CSPE compatibilized by the ionomer behaves as an oil resistant thermoplastic elastomer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 792–798, 2006     

Mechanical and thermal properties of (acrylonitrile‐styrene‐acrylic)/(α‐methylstyrene‐acrylonitrile) binary blends

In this work, (acrylonitrile‐styrene‐acrylic)/(α‐methylstyrene‐acrylonitrile) copolymer (ASA/α‐MSAN) binary alloy was prepared with different composition ratios via melt blending. This work mainly focused on improving the heat resistance of ASA. According to the results of dynamic mechanical thermal analysis, the binary blends exhibited three glass transition temperatures (T_gs) and the shift of the T_gs indicated the partial miscibility of binary blends. This partial miscibility maintained the high T_g of α‐MSAN, which led to the outstanding heat resistance of binary blends. Furthermore, heat distortion temperature also showed that the heat resistance of binary blends was significantly enhanced with the addition of α‐MSAN. However, the introduction of this highly rigid polymer also brought with it the sharp decrease of the impact strength and elongation at break, which is reflected in the morphologies of the blend system obtained via scanning electron microscopy. In addition, the incorporation of α‐MSAN increased the tensile strength, flexural strength, and modulus. There were no new groups observed from Fourier‐transform infrared spectra, which means no strong specific intermolecular interactions existed between ASA and α‐MSAN. Moreover, the processibility of the blend system was obviously improved from the results of melt flow rate. J. VINYL ADDIT. TECHNOL., 22:156–162, 2016. © 2014 Society of Plastics Engineers     

Synthesis and properties of novel amphiphilic sulfated ionomers by the ring‐opening reaction of an epoxidized styrene–butadiene–styrene triblock copolymer

A method for the synthesis of novel sulfated ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed. SBS was first epoxidized by performic acid in the presence of a phase‐transfer catalyst; this was followed by a ring‐opening reaction with an aqueous solution of alkali salt of bisulfate. The optimum conditions for the ring‐opening reaction of the epoxidized SBS with an aqueous solution of KHSO₄ were studied. During the ring‐opening reaction, both phase‐transfer catalyst and ring‐opening catalyst were necessary to enhance the conversion of epoxy groups to ionic groups. The products were characterized with Fourier transform infrared spectrophotometry and transmission electron microscopy (TEM). After the potassium ions of the ionomer were substituted with lead ions, the lead sulfated ionomer exhibited dark spots under TEM. Some properties of the sulfated ionomer were studied. With increasing ionic groups or ionic potential of the cations, the water absorbency and emulsifying volume of the ionomer and the intrinsic viscosity of the ionomer solution increased, whereas the oil absorbency decreased. The sulfated ionomer possessed excellent emulsifying properties compared with the sulfonated SBS ionomer. The sodium sulfated ionomers in the presence of 10% zinc stearate showed better mechanical properties than the original SBS. When the ionomer was blended with crystalline polypropylene, a synergistic effect occurred with respect to the tensile strength. The ionomer behaved as a compatibilizer for blending equal amounts of SBS and oil‐resistant chlorohydrin rubber. In the presence of 3% ionomer, the blend exhibited much better mechanical properties and solvent resistance than the blend without the ionomer. SEM photographs indicated improved compatibility between the two components of the blend in the presence of the ionomer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Toughening modification of (Acrylonitrile‐styrene‐acrylic copolymer)/(α‐Methylstyrene‐acrylonitrile copolymer) binary blend via using different impact modifiers

In this work, different impact modifiers such as acrylic resin impact modifier, chlorinated polyethylene (CPE), nitrile rubber, powdered nitrile rubber, and hydrogenated nitrile rubber, were chosen to improve the toughness of (acrylonitrile‐styrene‐acrylic copolymer)/(α‐methylstyrene‐acrylonitrile copolymer) (ASA/α‐MSAN) binary blend. The blend ratios of the ASA/(α‐MSAN)/(impact modifier) ternary system were 30/70/20 and 70/30/20 by mass, respectively. The results showed that the impact strength significantly increased, nearly 30 times (22.59 kJ·m^?2, 22.26 kJ·m^?2, and 25.24 kJ·m^?2) compared with that of control samples (0.80 kJ·m^?2) when nitrile rubber, powdered nitrile rubber, or hydrogenated nitrile rubber was added to the ASA/(α‐MSAN) (30/70) matrix, respectively. Moreover, the impact strength of ASA/(α‐MSAN) (70/30) was dramatically enhanced to 46 kJ·m^?2 with the addition of 20 parts by weight per hundred parts of resin of chlorinated polyethylene. The toughness of ASA/(α‐MSAN) with or without impact modifiers was also characterized via fracture energy calculated from stress‐strain curves. The results were perfectly consistent with that of impact strength. The results of dynamic mechanical analysis demonstrated the existence of α‐MSAN (glass transition temperature at approximately 140°C). The heat distortion temperature was barely changed, indicating the addition of impact modifiers barely affects the heat resistance. J. VINYL ADDIT. TECHNOL., 22:326–335, 2016. © 2014 Society of Plastics Engineers     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Crystallization,morphology, and mechanical behavior of polylactide/poly(ε‐caprolactone) blends

Optically pure polylactides, poly(L ‐lactide) (PLLA) and poly(D ‐lactide) (PDLA), were blended across the range of compositions with poly(ε‐caprolactone) (PCL) to study their crystallization, morphology, and mechanical behavior. Differential scanning calorimetry and dynamic mechanical analysis (DMA) of the PLA/PCL blends showed two T_gs at positions close to the pure components revealing phase separation. However, a shift in the tan δ peak position by DMA from 64 to 57°C suggests a partial solubility of PCL in the PLA‐rich phase. Scanning electron microscopy reveals phase separation and a transition in the phase morphology from spherical to interconnected domains as the equimolar blend approaches from the outermost compositions. The spherulitic growth of both PLA and PCL in the blends was followed by polarized optical microscopy at 140 and 37°C. From tensile tests at speed of 50 mm/min Young's modulus values between 5.2 and 0.4 GPa, strength values between 56 and 12 MPa, and strain at break values between 1 and 400% were obtained varying the blend composition. The viscoelastic properties (E′ and tan δ) obtained at frequency of 1 Hz by DMA are discussed and are found consistent with composition, phase separation, and crystallization behavior of the blends. POLYM. ENG. SCI., 46:1299–1308, 2006. © 2006 Society of Plastics Engineers     

Toughening effect of CPE on ASA/SAN binary blends at different temperatures

The effect of chlorinated polyethylene (CPE) on the impact toughness of acrylonitrile–styrene–acrylic (ASA) terpolymer/styrene–acrylonitrile copolymer (SAN) binary blends (25/75, w/w) was systematically investigated at three different temperatures (?30 °C, 0 °C, and 23 °C). With the addition of 60 phr CPE, the impact strength increased by 11 times at 23 °C and 10 times at 0 °C. However, the toughening effect was not obvious when the testing temperature was ?30 °C. Since the glass‐transition temperature (T_g) of CPE was about ?18.3 °C as measured with dynamic mechanical analysis tests, the polymeric chains of CPE have been “frozen out” at ?30 °C. As a result, CPE evidently cannot improve the toughness of the blend system. The morphology of impact‐fractured surfaces observed by scanning electron microscopy also confirmed the effect of CPE on the impact toughness of ASA/SAN binary blends. The heat distortion temperature remained almost unchanged, indicating that the improvement in toughness did not sacrifice heat resistance. Furthermore, other mechanical properties were evaluated, and the possible interactions among components of the blends were also analyzed by Fourier transform infrared spectra. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43353.     

Uniaxial tensile behavior and thermoforming characteristics of high barrier EVOH‐based blends of interest in food packaging

The uniaxial tensile characteristics of blends of an ethylene‐vinyl alcohol copolymer (EVOH‐32 mol% ethylene) with an amorphous PA and/or a nylon‐containing ionomer, used as barrier layer in multilayer food packaging structures, was assessed in this paper. The stress‐strain behavior of these materials at elevated temperatures and at different strain rates was examined. The stress‐strain curves obtained were used to understand the influence of temperature and strain rate on the uniaxial deformation process of the materials, these being of general importance during typical processing steps including thermoforming. A male mold for deep‐draw was used to assess the thermoforming (biaxial deformation in nature) behavior of extruded sheets at 100, 120, 140 and 150°C, and the results were broadly found to be in agreement with results from simple uniaxial tensile tests. From the preliminary thermoforming results, it was found that EVOH/aPA extruded blends did not improve the poor formability of EVOH alone. In contrast, significant improvement in thermoformability was achieved by blending EVOH with a compatibilized ionomer. Optimum forming capacity was achieved in a ternary blend by addition of a compatibilized ionomer to an EVOH/aPA blend in the range of 140°C–150°C. The ternary blend showed a lower reduction of thickness in the sidewalls, as well as a higher dimensional uniformity in the thermoformed part. Polym. Eng. Sci. 44:598–608, 2004. © 2004 Society of Plastics Engineers.     

Heat‐sealing properties of soy protein isolate/poly(vinyl alcohol) blend films: Effect of the heat‐sealing temperature

To promote the heat‐sealing properties of soy protein isolate (SPI) films applied in the packaging field, we mixed a synthetic polymer of poly(vinyl alcohol) (PVA) with SPI to fabricate blend films by a solution‐casting method in this study. To clarify the relationship between the heat‐sealing properties and the heat‐sealing temperature, strength, melting process, crystalline structure, and microstructure, variations of the heat‐sealing parts of the films were evaluated by means of differential scanning calorimetry, tensile testing, scanning electron microscopy, X‐ray diffraction, and Fourier transform infrared spectroscopy, respectively. The test results showed that both the PVA and glycerol contents greatly affected the melting behavior and heat of fusion of the SPI/PVA blends; these blend films had a higher melting temperature than the pure SPI films. The peel strength and tensile strength tests indicated that the long molecular chain of PVA had a main function of enhancing the mechanical properties above the melting temperature. With increasing heat‐sealing temperature, all of the mechanical properties were affected by the microstructure of the interface between the laminated films including the chain entanglement, crystallization, and recrystallization. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of the ultradrawing behavior of gel films of ultrahigh‐molecular‐weight polyethylene and low‐molecular‐weight polyethylene blends on their physical properties

This study examined the effect of the ultradrawing behavior of gel film specimens of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and UHMWPE/low‐molecular‐weight polyethylene (LMWPE) blends on their physical properties. The concentration of a gel film approximated its critical concentration at a fixed drawing temperature; its achievable draw ratio was higher than that of other blend specimens with various concentrations. Noticeably, when about 5 wt % LMWPE was added to a UHMWPE/LMWPE gel film specimen, the achievable draw ratio of the gel film increased, and this contributed to an apparent promoting effect on its anticreeping properties and thermal stability. Therefore, when UL_B?0.9 was drawn to a draw ratio of 300, the anticreeping behavior was improved to less than 0.026%/day. Moreover, with respect to the thermal stability, when the same specimen was drawn to a draw ratio of 300, the retention capability of its storage modulus could resist a high temperature of 150°C, which was obviously much higher than the temperature of an undrawn gel film specimen (70°C). To study these interesting behaviors further, this study systematically investigated the gel solution viscosities, anticreeping properties, dynamic mechanical properties, thermal properties, molecular orientations, and mechanical properties of undrawn and drawn UHMWPE/LMWPE gel film specimens. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Sorption,diffusion, and pervaporation separation of water–acetic acid mixtures through the blend membranes of sodium alginate and guar gum‐grafted‐polyacrylamide

Nonporous homogeneous dense membranes were prepared from the blends of sodium alginate (Na–Alg) with guar gum‐grafted polyacrylamide (GG‐g‐PAAm) in the ratios of 3 : 1 and 1 : 1 and these were tested for the pervaporation separation of water–acetic acid mixtures at 30°C. Blend compatibility was studied in solution by measuring the viscosity and the speed of sound. Membranes were crosslinked by glutaraldehyde. The GG‐g‐PAAm polymer and the crosslinked blend membranes were characterized by Fourier transform infrared spectra. High separation selectivity was exhibited by the pure Na–Alg membrane for water–acetic acid (HAc) mixtures containing 20 mass % of water. The permeation flux increased with increasing mass percent of water in the feed as well as with an increase in the amount of GG‐g‐PAAm in the blend, but separation selectivity decreased. Sorption selectivity was higher for the Na–Alg membrane than for the blend membranes, but it decreased with increasing mass percent of GG‐g‐PAAm in the blends. Diffusion selectivity values vary systematically with the blend composition, but not with the amount of water in the feed. Diffusion coefficients of the water–HAc mixtures were calculated from Fick's equation using sorption data and compared with those calculated from flux values obtained in pervaporation experiments. The Arrhenius activation parameters were calculated for the 20 mass % of water in the feed using flux and diffusion data obtained at 30, 40, and 50°C. The diffusion and pervaporation results are explained in terms of solution–diffusion concepts. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 259–272, 2002     

Sealing Glass‐Ceramics with Near‐Linear Thermal Strain,Part II: Sequence of Crystallization and Phase Stability

The sequence of crystallization in a recrystallizable lithium silicate sealing glass‐ceramic Li₂O–SiO₂–Al₂O₃–K₂O–B₂O₃–P₂O₅–ZnO was analyzed by in situ high‐temperature X‐ray diffraction (HTXRD). Glass‐ceramic specimens have been subjected to a two‐stage heat‐treatment schedule, including rapid cooling from sealing temperature to a first hold temperature 650°C, followed by heating to a second hold temperature of 810°C. Notable growth and saturation of Quartz was observed at 650°C (first hold). Cristobalite crystallized at the second hold temperature of 810°C, growing from the residual glass rather than converting from the Quartz. The coexistence of quartz and cristobalite resulted in a glass‐ceramic having a near‐linear thermal strain, as opposed to the highly nonlinear glass‐ceramic where the cristobalite is the dominant silica crystalline phase. HTXRD was also performed to analyze the inversion and phase stability of the two types of fully crystallized glass‐ceramics. While the inversion in cristobalite resembles the character of a first‐order displacive phase transformation, i.e., step changes in lattice parameters and thermal hysteresis in the transition temperature, the inversion in quartz appears more diffuse and occurs over a much broader temperature range. Localized tensile stresses on quartz and possible solid‐solution effects have been attributed to the transition behavior of quartz crystals embedded in the glass‐ceramics.     

Water stability of high‐molecular‐weight (HMW) syndiotacticity‐rich poly(vinyl alcohol) (PVA)/HMW atactic PVA/iodine complex blend films

To precisely identify the effect of blend ratios of syndiotacticity‐rich poly(vinyl alcohol) (s‐PVA)/atactic PVA (a‐PVA) on the water stability of s‐PVA/a‐PVA/iodine complex blend films, we prepared two PVAs with similar number‐averaged degrees of polymerization of 4000 and degrees of saponification of 99.9% and with different syndiotactic diad contents of 58.5 and 53.5%, respectively. The desorption behavior of iodine in s‐PVA/a‐PVA/iodine complex films in water was investigated in terms of the solubility of s‐PVA/a‐PVA blend films in water. The degree of solubility of s‐PVA/a‐PVA blend films with s‐PVA content over 50% in water at 70°C was limited to about 10–20%, whereas that of s‐PVA/a‐PVA blend films with s‐PVA content of 10% was 85% under the same conditions. The degree of iodine desorption of complex blend films decreased with increasing s‐PVA content. The degree of iodine desorption of s‐PVA/a‐PVA drawn film with s‐PVA content of 90% was limited to 7%, regardless of the soaking temperature from 30 to 70°C. The desorption of iodine in water was strongly affected by the dissolution of blends. Moreover, the stability of iodine in the drawn s‐PVA/a‐PVA/iodine blend films in hot water was far superior to that of the undrawn film. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1435–1439, 2004     

Study of the thermoformability of ethylene‐vinyl alcohol copolymer based barrier blends of interest in food packaging applications

The thermoforming capacity of a number of blends of an ethylene‐vinyl alcohol copolymer (EVOH‐32, with 32 mol % ethylene) with amorphous polyamide (aPA) and/or Nylon‐containing ionomer with interest in multilayer food packaging structures have been studied. These blends were vacuum‐thermoformed between 100 and 150°C onto male molds of different shapes and areal draw ratios. It was found that EVOH/aPA extruded blends did not improve the inherently poor formability of EVOH alone. In contrast, significant improvements in thermoformability were achieved by blending EVOH with a compatibilized‐ionomer. Optimum forming capacity was achieved in a ternary blend by addition of a compatibilized‐ionomer to EVOH/aPA blends in the range of 140–150°C. Analysis of wall thickness data obtained in the thermoformed parts showed that wall thickness was significantly affected by the ionomer and amorphous polyamide content in the blend. The ternary blend showed a lower thickness reduction in the critical areas, as well as a higher uniformity in the part. A finite element analysis was used to evaluate the wall thickness distribution and the modeling results were compared with the thermoforming experiments. The simulations were performed for the vacuum‐forming process employing a nonlinear elastic material model. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 96: 3851–3855, 2004     

Mechanical,rheological, and electrical properties of multiwalled carbon nanotube reinforced ASA/Na‐ionomer blend

Varying amounts of multiwalled carbon nanotubes (MWCNTs) was melt‐extruded with the acrylonitrile‐styrene‐acrylate (ASA)/Na‐ionomer blend, and mechanical, rheological, and electrical properties were studied Optical micrographs show good dispersion level at low MWCNT content and network formation at higher nanotubes percentage. DC conductivity model data shows percolation threshold reached at 1% MWCNT content and after percolation, two‐dimensional network structure was formed. The “peak and valley” type surface topology of matrix may be responsible for low percolation threshold limit. The polymer/nanotubes interactions at low MWCNT content increased the mechanical strengths, which were reduced by the network structure and agglomerates of nanotubes at higher nanotubes content. The MWCNTs interacted differently with the architecturally complex polymer chains and controlled chain dynamics accordingly. The Carreau‐Yasuda model was found fit to viscosity data and the model parameters data suggest the zero shear viscosity is function of MWCNTs content but the infinite shear viscosity is independent of nanoparticles content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42516.     

Open‐cell foams of polyethylene terephthalate/bisphenol a polycarbonate blend

Open microcellular foams of polyethylene terephthalate (PET)/polycarbonate (PC) blends were prepared by controlling their foaming behavior at the interface between these two polymers. Interface modification was a crucial factor in governing the foaming behavior and cell morphology of the blend foams: annealing at 280°C, i.e., conducting the transesterification reaction, generates a PET‐b‐PC copolymer, which lowers the interfacial tension, increases the affinity between PET and PC, and decreases the crystallinity of the PET domains. When CO₂ foaming was performed at the interface modified with the copolymer, an interesting fibril‐like structure was formed. The cell density of the PET/PC blend then increased, and its cell size reduced to the microscale while maintaining a high open‐cell ratio. The effect of heat annealing (transesterification reaction) on CO₂‐foaming was studied to reveal the relationship among the interface affinity, crystallinity, and degree of fibrillation. The optimal heat‐annealing procedure generated a fibril‐like structure in the PET/PC blend foams with a high cell density (7 × 10¹¹ cm^?3), small cell size (less than 2 μm), and 100% open‐cell ratio. POLYM. ENG. SCI., 55:375–385, 2015. © 2014 Society of Plastics Engineers     

Crystallization behavior of dry‐brush PEO‐PS block copolymer and PEO homopolymer blend

The crystallization behavior of semicrystalline PEO homopolymer/triblock PS‐PEO‐PS copolymer blend system, which exhibited “Dry‐Brush” in the melt. A symmetric polystyrene–poly(ethylene oxide)–polystyrene triblock copolymer was blended with PEO homopolymer (h‐PEO) having the same molecular weight as that of the PEO block in the copolymer. Considering the composition of the blend (W_ps ≥ 0.8), PEO spheres were formed in the blend. Because of the dry‐brush phase behavior of this blend, h‐PEO added was localized in the PEO microdomains, which increases the domain size without changing the microdomain morphology. The crystallization of PEO block was confined within the microdomains and the crystallization temperature was about 60°C lower than normal. Self‐seeding tests were performed to clarify the nucleation mechanism of the blend. Because the droplets size varies greatly, multicrystallization peaks were witnessed in the self‐seeding process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Partially Sulfonated Poly(1,4‐phenylene ether‐ether‐sulfone) and Poly(vinylidene fluoride) Blend Membranes for Fuel Cells

Blend membranes based on high conductive sulfonated poly(1,4‐phenylene ether‐ether‐sulfone) (SPEES) and poly(vinylidene fluoride) (PVDF) having excellent chemical stability were prepared and characterized for direct methanol fuel cells. The effects of PVDF content on the proton conductivity, water uptake, and chemical stability of SPEES/PVDF blend membranes were investigated. The morphology, miscibility, thermal, and mechanical properties of blend membranes were also studied by means of scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA) measurements. The blend membrane containing 90 wt.% SPEES (degree of sulfonation – DS = 72%) and 10 wt.% PVDF (M_w = 180,000) exhibits optimum properties among various SPEES72/PVDF membranes. Addition of PVDF enhanced resistance of the SPEES membrane against peroxide radicals and methanol significantly without deterioration of its proton conductivity. It's proton conductivity at 80 °C and 100% relative humidity is higher than Nafion 115 while it's methanol permeability is only half of that of Nafion 115 at 80 °C. The direct methanol fuel cell performance of the SPEES membranes was better than that of Nafion 115 membrane at 80 °C.