Oxo‐biodegradability of high‐density polyethylene films containing limited amount of isotactic polypropylene

Limited amount of isotactic polypropylene (iPP) is added to high‐density polyethylene (HDPE) containing 1% w/w an oxo‐biodegradable additive and extruded and converted to films. The films are put under UV irradiation for different periods of time. Irradiation of the films for 6 weeks imposes remarkable effects on viscosity average molecular weight (M_v) and carbonyl index (CI) of them. M_v decreases from 3.4 × 10⁵ to 4.7 × 10⁴ g mol^?1 for neat HDPE films; from 3.1 × 10⁵ to 3.3 × 10⁴ g mol^?1 for the films containing oxo compound, and from 1.5 × 10⁵ to 2.6 × 10⁴ g mol^?1 for the films containing oxo compound and 1% w/w iPP. Carbonyl index of the neat HDPE films increases from 4 to 8.7 while for the sample containing only the oxo compound it increases from 4.5 to 7.3 and for the sample containing both oxo compound and iPP it decreases from 12.0 to 8.8. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) indicate more cracks and uniform degradation in the samples containing iPP and oxo compound. Thermogravimetric analysis (TGA/DTG) of the samples shows that the samples containing iPP and oxo compound have lower decomposition temperature after UV irradiation. Finally, it can be said that the presence of iPP in HDPE matrix containing oxo compound can improve HDPE oxo‐biodegradablity. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45843.     

High‐molecular‐weight aliphatic polycarbonates by melt polycondensation of dimethyl carbonate and aliphatic diols: synthesis and characterization

Aliphatic polycarbonates (APCs) synthesized by polycondensation of dialkyl carbonates and aliphatic diols have often been used as precursors for the preparation of novel polyurethanes. However, they could not be applied in plastics directly because of poor mechanical properties caused by low molecular weight. In the work reported in this paper, three kinds of fairly high molecular weight (M_w ≥ 166 000 g mol^?1) APCs with narrow dispersity ( ) were successfully synthesized via a successive two‐step polycondensation of dimethyl carbonate and diols, using a novel TiO₂/SiO₂‐based catalyst. This process gave a high yield of above 85%. ¹H NMR spectra indicated that there was no detectable decarboxylation happening during polycondensation at high temperature. The effects of molecular weight on the mechanical properties of the APCs are discussed. APCs with M_w greater than 70 000 g mol^?1 showed useful mechanical properties. Especially, poly(butylene carbonate) and poly(hexamethylene carbonate) exhibited excellent tensile strengths of 34.1 and 40.0 MPa, respectively, when their M_w was ca 170 000 g mol^?1. All the APCs showed appreciable biodegradability under enzymatic degradation. Copyright © 2011 Society of Chemical Industry     

An activated neodymium‐based catalyst for styrene polymerization

Coordination polymerization of styrene with a ternary catalyst system composed of catalyst neodymium tricarboxylate (Nd), co‐catalyst Al(i‐Bu)₃ (Al) and chlorinating agent trichloroethane (Cl) was carried out in cyclohexane. The effects of the catalyst system preparation procedure and of the reaction conditions on catalytic activity, molecular weight and molecular weight distribution of the resultant polymers were investigated. The catalytic activity depended mainly on the molar ratios of Al/Nd and of Cl/Nd and on the ageing temperature and polymerization temperature. High polymerization conversion and high catalytic activity could be obtained at high Al/Nd ratios and/or at high ageing temperature. The catalyst system exhibited high activity of 8.32 × 10⁴ g polystyrene (mol Nd h)^?1 at 50 °C. The molecular weight of the polymers obtained reached high weight‐average (M_w) values (M_w = 4.35 × 10⁵ g mol^?1) when Al/Nd = 8, but relatively low values (6000–11 000 g mol^?1) at high Al/Nd ratios. Copyright © 2005 Society of Chemical Industry     

Synthesis and characteristics of a novel aliphatic polycarbonate,poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)]

A novel aliphatic polycarbonate, poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)] [P(PO? CO₂? GBL)], was synthesized by the copolymerization of carbon dioxide, propylene oxide (PO) and γ‐butyrolactone (GBL). The resulting copolymers were determined by FTIR and NMR spectral analysis with viscosity‐average molecular weights (M_v) from 50 000 to 120 000 g mol^?1. According to elemental analysis, the calculated data of elemental contents in P(PO? CO₂? GBL)44 were close to the found data. The result showed that GBL was inserted into the backbone of poly[(propylene oxide)‐co‐(carbon dioxide)] successfully. GBL offered an ester structural unit that gave the copolymer better degradability. The correlations between reaction conditions and properties were studied. When GBL content increased, the M_v and the glass transition temperature (T_g) of the copolymers improved relative to an identical copolymer without GBL. Prolonging the reaction time of the copolymerization resulted in increases in M_v and T_g. P(PO? CO₂? GBL) exhibited a high T_g above 40 °C. The rate of backbone degradation increased with increasing GBL content. Copyright © 2005 Society of Chemical Industry     

Synthesis,characterization, conductivity,band gap,and kinetic of thermal degradation of poly‐4‐[(2‐mercaptophenyl) imino methyl] phenol

The oxidative polycondensation reaction conditions of 4‐[(2‐mercaptophenyl) imino methyl] phenol (2‐MPIMP) were studied in an aqueous acidic medium between 40 and 90°C by using oxidants such as air, H₂O₂, and NaOCl. The structures of the synthesized monomer and polymer were confirmed by FTIR, ¹H NMR, ¹³C NMR, and elemental analysis. The characterization was made by TGA‐DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly‐4‐[(2‐mercaptophenyl) imino methyl]phenol (P‐2‐MPIMP) was found to be 92% for NaOCl oxidant, 84% for H₂O₂ oxidant 54% for air oxidant. According to the SEC analysis, the number‐average molecular weight (M_n), weight‐average molecular weight (M_w), and polydispersity index values of P‐2‐MPIMP were found to be 1700 g mol^?1, 1900 g mol^?1, and 1.118, using H₂O₂; 3100 g mol^?1, 3400 g mol^?1, and 1.097, using air; and 6750 g mol^?1, 6900 g mol^?1, and 1.022, using NaOCl, respectively. According to TG analysis, the weight losses of 2‐MPIMP and P‐2‐MPIMP were found to be 95.93% and 76.41% at 1000°C, respectively. P‐2‐MPIMP showed higher stability against thermal decomposition. Also, electrical conductivity of the P‐2‐MPIMP was measured, showing that the polymer is a typical semiconductor. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, and the electrochemical energy gaps (E′_g) of 2‐MPIMP and P‐2‐MPIMP were found to be ?6.13, ?6.09; ?2.65, ?2.67; and 3.48, 3.42 eV, respectively. Kinetic and thermodynamic parameters of these compounds investigated by MacCallum‐Tanner and van Krevelen methods. The values of the apparent activation energies of thermal decomposition (E_a), the reaction order (n), pre‐exponential factor (A), the entropy change (ΔS*), enthalpy change (ΔH*), and free energy change (ΔG*) were calculated from the TGA curves of compounds. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry     

Synthesis,characterization, and antimicrobial properties of oligo‐4‐[(pyridine‐3‐yl‐methylene) amino] phenol

The oxidative polycondensation reaction conditions of 4‐[(pyridine‐3‐yl‐methylene) amino]phenol (4‐PMAP) were studied using H₂O₂, atmospheric O₂, and NaOCl oxidants in an aqueous alkaline medium between 30°C and 90°C. Synthesized oligo‐4‐[(pyridine‐3‐yl‐methylene) amino] phenol (O‐4‐PMAP) was characterized by ¹H‐, ¹³C NMR, FTIR, UV–vis, size exclusion chromatography (SEC), and elemental analysis techniques. The yield of O‐4‐PMAP was found to be 32% (for H₂O₂ oxidant), 68% (for atmospheric O₂ oxidant), and 82% (for NaOCl oxidant). According to the SEC analysis, the number–average molecular weight, weight–average molecular weight, and polydispersity index values of O‐4‐PMAP was found to be 5767, 6646 g mol^?1, and 1.152, respectively, using H₂O₂, and 4540, 5139 g mol^?1, and 1.132, respectively, using atmospheric O₂, and 9037, 9235 g mol^?1, and 1.022, using NaOCl, respectively. According to TG and DSC analyses, O‐4‐PMAP was more stable than 4‐PMAP against thermal decomposition. The weight loss of O‐4‐PMAP was found to be 94.80% at 1000°C. Also, antimicrobial activities of the oligomer were tested against B. cereus, L. monocytogenes, B. megaterium, B. subtilis, E. coli, Str. thermophilus, M. smegmatis, B. brevis, E. aeroginesa, P. vulgaris, M. luteus, S. aureus, and B. jeoreseens. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3327–3333, 2006     

Effect of polymer chain length on the solubility of polystyrene grafted single‐walled carbon nanotubes in tetrahydrofuran

BACKGROUND: While carbon nanotubes are highly interesting materials for a variety of applications, their inherent insolubility limits widespread applications and solution‐phase processing. It is known that chemical functionalization can overcome this insolubility problem, and covalent grafting of polymers to the nanotube surface has been shown to be effective. In this study, the effect of polymer molecular weight on the solubility of polymer–nanotube conjugates was investigated. RESULTS: A series of nitroxide‐capped polystyrene polymers ranging in molecular weight from 2900 to 105 000 g mol^?1 were grafted to single‐walled carbon nanotubes (SWNTs). The resulting polystyrene–SWNT conjugates exhibited different degrees of solubility in tetrahydrofuran. Subsequent thermogravimetric and UV‐visible spectroscopy analyses indicated that carbon nanotube solubility reached a maximum when a polymer sample with a weight‐average molecular weight of 10 000 g mol^?1 was used. Higher and lower molecular weights resulted in reduced solubilities. CONCLUSION: Polymer chains of intermediate length maximize SWNT solubility, while lengths that are too low or too high seem to diminish the ability of the polymer–SWNT conjugates to remain in solution. Copyright © 2008 Society of Chemical Industry     

Examining the preparation and characterization of coatings based on linear aromatic terpoly(methoxy‐cyanurate‐thiocyanurate)s

Two series of terpoly(methoxy‐cyanurate‐thiocyanurate)s based on thiodiphenol and dithiodiphenyl sulfide and on dihydroxydiphenyl ether and dithiodiphenyl ether, were prepared in good yield and purity and fully characterized. Most of the resulting polymers, formed at room temperature using phase transfer catalysis, can be cast into films with good resilience and thermal stability (some examples suffer practically no mass loss when held isothermally at 190 °C and only display appreciable losses when held continuously at 225 °C). Char yields of 53%?61% are achieved in nitrogen depending on backbone structure. Some problems were encountered with solubility, particularly with copolymers, which limited molecular weight analysis, but values of M_n = 8000–13 000 g mol^?1 were obtained for the polymers based on thiodiphenol and dithiodiphenyl sulfide, and M_n = 5000–13 000 g mol^?1 for the polymers based on dihydroxydiphenyl ether and dithiodiphenyl ether. DSC reveals polymerization exotherms with maxima at 184–207 °C (ΔH_p = 43–59 kJ mol^?1), which are believed to be due to isomerization of the cyanurate to the isocyanurate (activation energies span 159–195 kJ mol^?1). Molecular simulation shows that diphenylether and diphenylsulfide display very similar conformational energy surfaces and would therefore be expected to adopt similar conformations, but the diphenylsulfide offers less resistance to deformations that increase the proximity of the two phenyl rings and results in more resilient films. © 2013 Society of Chemical Industry     

Synthesis and biological activity of medium range molecular weight polymers containing exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid (ETCA), was prepared by reaction of maleimidocaproic acid and furan. The homopolymer of ETCA and its copolymers with acrylic acid (AA) or with vinyl acetate (VAc) were obtained by photopolymerizations using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETCA and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The apparent average molecular weights and polydispersity indices determined by gel permeation chromatography (GPC) were as follows: M_n = 9600 g mol^?1, M_w = 9800 g mol^?1, M_w/M_n = 1.1 for poly(ETCA); M_n = 14 300 g mol^?1, M_w = 16 200 g mol^?1, M_w/M_n = 1.2 for poly(ETCA‐co‐AA); M_n = 17 900 g mol^?1, M_w = 18 300 g mol^?1, M_w/M_n = 1.1 for poly(ETCA‐co‐VAc). The in vitro cytotoxicity of the synthesized compounds against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines decreased in the following order: 5‐fluorouracil (5‐FU) ≥ ETCA > polymers. The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐FU at all doses tested. © 2001 Society of Chemical Industry     

Toughening of cyanate ester resin by N‐phenylmaleimide–N‐(p‐hydroxy)phenyl‐maleimide–styrene terpolymers and their hybrid modifiers

N‐Phenylmaleimide–N‐(p‐hydroxy)phenylmaleimide–styrene terpolymer (HPMS), carrying reactive p‐hydroxyphenyl groups, was prepared and used to improve the toughness of cyanate ester resins. Hybrid modifiers composed of N‐phenylmaleimide–styrene copolymer (PMS) and HPMS were also examined for further improvement in toughness. Balanced properties of the modified resins were obtained by using the hybrid modifiers. The morphology of the modified resins depends on HPMS structure, molecular weight and content, and hybrid modifier compositions. The most effective modification of the cyanate ester resin was attained because of the co‐continuous phase structure of the modified resin. Inclusion of the modifier composed of 10 wt% PMS (M_w 136 000 g mol^?1) and 2.5 wt% HPMS (hydroxyphenyl unit 3 mol%, M_w 15 500 g mol^?1) led to 135% increase in the fracture toughness (K_IC) for the modified resin with a slight loss of flexural strength and retention of flexural modulus and glass transition temperature, compared with the values for the unmodified resin. Furthermore, the effect of the curing conditions on the mechanical and thermal properties of the modified resins was examined. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behaviour of the modified cyanate ester resin system. © 2001 Society of Chemical Industry     

Melt rheological behavior of a triblock copolymer based on aramide end‐segments

Melt rheological behavior of a ABA triblock polymer made of poly(tetramethylene oxide) (PTMO) (M_n = 2,900 g mol^?1) soft segment and aramide hard segment was studied. The aramide end‐segments ( A ) were short and mono‐disperse in length. The mid‐segment ( B ) consisted of PTMO₂₉₀₀ extended with terephthalate units to a molecular weight of 9000 g mol^?1. The molecular weight of the triblock was 9700 g mol^?1. Rheological behavior of this material was studied by parallel‐plate and capillary method. The ABA triblock copolymer was compared with a B polymer (PTMO‐terephthalate) of a similar molecular weight. The low molecular weight B polymer had a Newtonian behavior. The low molecular weight triblock copolymer had at high frequencies a low complex viscosity. However, at low frequencies the triblock copolymer had a very high complex viscosity. Also the G″/G′ ratio decreased with decreasing frequency to values less then one and the G′ seemed to have at low frequencies a plateau value. The activation energy of the process increased in value with decreasing shear rate. All these results indicate that the triblock copolymer at low frequencies had a gel‐like behavior and this probably due to the clustering of the aramide segments. The aramide clusters are thought to be the (weak) network points of the gel. This network was also found to have a time dependant rheological response and thus a thixotropic behavior. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry     

Relaxational behavior and swelling‐pH master curves of poly[(diethylaminoethyl methacrylate)‐graft‐(ethylene glycol)] hydrogels

Poly[(diethylaminoethyl methacrylate)‐graft‐(ethylene glycol)] hydrogels were prepared with a molar ratio of 10:1 of diethylaminoethyl methacrylate to poly(ethylene glycol) of number‐average molecular weights (M_n) 200, 400 and 1000 g mol^?1 using tetra(ethylene glycol) dimethacrylate to give a crosslinking ratio between 0.5 and 4.0 %. Glucose oxidase and catalase were immobilized in the matrix during polymerization. The maximum enzyme loading used was 6.6 × 10^?4 g of glucose oxidase per g of polymer. The equilibrium and dynamic swelling properties of these hydrogels were investigated. The pH‐dependent equilibrium swelling characteristics showed a sharp transition between the swollen and the collapsed state at pH 7.0. The dynamic response of the hydrogel discs to pH was analyzed in pulsatile pH conditions. The effects of particle size, crosslinking and molecular weight of poly(ethylene glycol) (PEG) on the dynamic swelling response were investigated. The pulsatile nature of the response was analyzed using Boltzmann superposition. Swelling–pH master curves were obtained. Copyright © 2004 Society of Chemical Industry     

Dewetting and microphase separation in symmetric polystyrene‐block‐polyisoprene diblock copolymer ultrathin films

The kinetics of surface structure evolution in ultrathin films of low‐molecular‐weight polystyrene‐block‐polyisoprene (M_w: 7300 g mol^?1–7300 g mol^?1) diblock copolymer at temperatures below the bulk order‐to‐disorder transition temperature are presented. Films with two different thicknesses were studied as a function of annealing temperature using atomic force microscopy. These film thicknesses enabled the investigation of the competition between microphase separation and dewetting that resulted in two different morphologies: long‐range bicontinuous structures and random holes. Three distinctive stages of structure evolution were observed in bicontinuous structure, with the underlying mechanism compared with spinodal dewetting. Thicker films presented holes on their surfaces upon annealing at elevated temperatures, and kinetics of formation of the holes were discussed. We found that the molecular mobility determined the rates of dewetting, while the microphase separation hardly affected the dewetting process. © 2015 Society of Chemical Industry     

Vinyl‐type homo‐ and copolymerization of norbornene catalyzed by bis(phenoxyimine) titanium complex

A ternary catalytic system consisting of a bis(phenoxyimine) titanium complex, triisobutylaluminium and an organoboron compound exhibited high activity in the vinyl‐type homopolymerization of norbornene. The obtained polynorbornene showed a modest molecular weight (M _n ≈ 5 × 10⁴ g mol^?1) and broad molecular weight distribution (polydispersity index ≈ 3.5). A copolymer of norbornene with 1,3‐butadiene was prepared using a binary catalytic system consisting of bis(phenoxyimine) titanium complex and triisobutylaluminium. The norbornene units in the copolymer adopted a vinyl‐type addition structure confirmed using distortionless enhancement by polarization transfer 135 ¹³C NMR microstructure analyses. Polymerization kinetics studies showed that neither monomer feed ratio nor conversion had an effect on the composition of the copolymer backbone which was composed of 55% norbornene units and 45% 1,3‐butadiene units. The essentially constant polymer composition implied an alternating nature of chain propagation. The copolymer exhibited good thermal stability and moderate glass transition temperature (50.9–68.2 °C) with a relatively high molecular weight (M _w = 0.18 × 10–1.31 × 10⁵ g mol^?1), and excellent transparency (maximal transmittance >80%). © 2017 Society of Chemical Industry     

Synthesis and characterization of biodegradable lactic acid‐based polymers by chain extension

BACKGROUND: Poly(lactic acid) (PLA), coming from renewable resources, can be used to solve environmental problems. However, PLA has to have a relatively high molecular weight in order to have acceptable mechanical properties as required in many applications. Chain‐extension reaction is an effective method to raise the molecular weight of PLA. RESULTS: A high molecular weight biodegradable lactic acid polymer was successfully synthesized in two steps. First, the lactic acid monomer was oligomerized to low molecular weight hydroxyl‐terminated prepolymer; the molecular weight was then increased by chain extension using 1,6‐hexamethylene diisocyanate as the chain extender. The polymer was characterized using ¹H NMR analysis, gel permeation chromatography, differential scanning calorimetry and Fourier transform infrared spectroscopy. The results showed that the obtained polymer had a M_n of 27 500 g mol^?1 and a M_w of 116 900 g mol^?1 after 40 min of chain extension at 180 °C. The glass transition temperature (T_g) of the low molecular weight prepolymer was 47.8 °C. After chain extension, T_g increased to 53.2 °C. The mechanical and rheological properties of the obtained polymer were also investigated. CONCLUSION: The results suggest that high molecular weight PLA can be achieved by chain extension to meet conventional uses. Copyright © 2008 Society of Chemical Industry     

Core–shell type multi‐arm azide polymers based on hyperbranched copolyether as potential energetic materials in solid propellants

A series of novel multi‐arm azide copolymers (POGs) with the same hyperbranched poly[3‐ethyl‐3‐(hydroxymethyl)oxetane] core (PEHO‐c) and different content of linear glycidyl azide polymer shell (GAP‐s) have been synthesized by sequential cationic ring‐opening polymerization and azidation. Detailed structural information of these copolyethers was deduced from Fourier transform infrared, ¹H NMR and inverse gated decoupled ¹³C NMR spectroscopies, matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry, gel permeation chromatography and elemental analysis. The molecular weight of POG having GAP‐s and PEHO‐c with a molar ratio 14.95:1 (R_s/c) was around 31 000 g mol^?1, far above that of linear GAP (around 4000 g mol^?1). The apparent viscosity and glass transition temperature (?51 to ?23 °C) decreased first and then slightly increased with increasing molecular weight. Thermal analysis revealed that all the obtained POGs exhibited excellent resistance to thermal decomposition up to 220 °C. Moreover, the energetic properties, investigated using oxygen bomb calorimetric measurements, indicated that the enthalpy of formation of the POGs was higher than that of general linear GAP, but similar to that of branched GAP under reasonable R_s/c. The compatibilities of the POGs with common materials used in solid propellants were studied using differential scanning calorimetry and the results indicated that the POGs had good compatibility with these materials. © 2017 Society of Chemical Industry     

Synthesis and characterization of oligosalicylaldehyde‐graft‐oligoaniline and its beginning oligomers

Conjuge bonding oligosalicylaldehyde‐graft‐oligoaniline (OSA‐graft‐OA) was synthesized from the polycondensation reaction of oligosalicylaldehyde (OSA) with oligoaniline (OA). There were various functional groups such as ? OH, ? NH and ? CH?N in the structure of the graft cooligomer. The physical properties of graft‐co‐oligomers such as melting temperature and solubility were studied: number‐average molecular weight, mass‐average molecular weight, and a polydispersity index of OA, OSA, and fractions of the graft cooligomers [(OSA‐graft‐OA)‐I] and [(OSA‐graft‐OA)‐II] were found to be 740, 780 g mol^?1,1.05; 3700, 5990 g mol^?1, 1.62; 990, 2770 g mol^?1, 2.80 and 1300, 4100 g mol^?1, 3.15, respectively. The FTIR and UV‐Vis spectra of the graft cooligomer were compared with those of beginning oligomers. The spectral analyses results showed that the OSA‐graft‐OA synthesized from the polycondensation reaction of aromatic amine with aldehyde that have long oligophenol macromolecule bonded each other with an azomethine bridge through oligophenylamine side chains. The thermal stability of the graft cooligomer and oligomers were measured by thermogravimetric analysis (TG) under an air atmosphere. According to TG analyses, the carboneous residues of the [(OSA‐graft‐OA)‐I) (soluble in ethanol) and (OSA‐graft‐OA)‐II) (soluble in toluene)] were 23 and 40%, respectively, at 1000°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 218–226, 2002     

Effect of oxalic acid on the rheological properties of dope solution of poly[acrylonitrile‐co‐(methyl acrylate)‐co‐(itaconic acid)]

The very high dope viscosity of concentrated dope of poly[acrylonitrile‐co‐(methyl acrylate)‐co‐(itaconic acid)] (with M?_v = 10.67 × 10⁵g mol^?1) in DMF could be diminished significantly by the addition of oxalic acid (OXA). The change in steady shear rheological behaviour caused by OXA has been analysed for the dope using a rheometer working in the viscosity mode. The temperature dependence of η₀ conformed to the Arrhenius‐Frenkel‐Eyring equation. ΔG_v decreased marginally with OXA concentration, and the least value was observed at an OXA concentration of 0.63 % by weight. Shear thinning behaviour was observed under higher shear rates for the terpolymer solutions in the presence and absence of OXA. The pseudoplasticity index (n) showed an abrupt initial increase on addition of OXA. The OXA concentration of 0.63 % by weight was advantageous for decreasing the viscosity of the polymer dope. The reduction in viscosity is attributed to the disturbed polymer‐polymer interactions by way of H‐bonding of OXA with the polymer. OXA‐containing dope at higher shear rate could achieve very low viscosities. Copyright © 2004 Society of Chemical Industry