Thermal analysis of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) irradiated under vacuum

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was irradiated by ⁶⁰Co γ‐rays (doses of 50, 100 and 200 kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one‐step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight‐loss step change. The onset degradation temperature (T_o) and the temperature of maximum weight‐loss rate (T_p) of control and irradiated PHBV were in line with the heating rate (°C min^?1). T_o and T_P of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that ⁶⁰Co γ‐radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T_m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness. Copyright © 2004 Society of Chemical Industry     

Thermogravimetric analysis of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The thermal degradation of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐HV)] was studied using thermogravimetry (TG). In the thermal degradation of PHB, the temperature at the onset of weight loss (T_o) was derived by T_o = 0.97B + 259, where B represents the heating rate (°C/min). The temperature at which the weight loss rate was maximum (T_p) was T_p = 1.07B + 273, and the final temperature (T_f) at which degradation was completed was T_f = 1.10B + 280. The percentage of the weight loss at temperature T_p (C_p) was 69 ± 1% whereas the percentage of the weight loss at temperature T_f (C_f) was 96 ± 1%. In the thermal degradation of P(HB‐HV) (7:3), T_o = 0.98B + 262, T_p = 1.00B + 278, and T_f = 1.12B + 285. The values of C_p and C_f were 62 ± 7 and 93 ± 1%, respectively. The derivative thermogravimetric (DTG) curves of PHB confirmed only one weight loss step change because the polymer mainly consisted of the HB monomer only. The DTG curves of P(HB‐HV), however, suggested multiple weight loss step changes; this was probably due to the different evaporation rates of the two monomers. The incorporation of 10 and 30 mol % of the HV component into the polyester increased the various thermal temperatures (T_o, T_p, andT_f) by 7–12°C (measured at B = 20°C/min). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2237–2244, 2001     

Thermo‐oxidative decomposition kinetics of elastomeric composites based on styrene‐(ethylene‐butylene)‐styrene triblock copolymer and organomontmorillonite

The elastomeric nanocomposites based on organomontmorillonite (OMMT) and styrene‐(ethylene‐butylene)‐styrene (SEBS) thermoplastic elastomer were prepared by melt processing using maleic anhydride grafted SEBS (SEBS‐g‐MA) as compatibilizer. Thermo‐oxidative decomposition behavior of the neat components and the nanocomposites were investigated using thermogravimertic analysis (TGA) in air atmosphere. The isoconversional method is employed to study the kinetics of thermo‐oxidative degradation. The heating modes and the composition of nanocomposites were found to affect the kinetic parameters (E_a, lnA and n). The E_a and lnA values of SEBS, OMMT, and their composites are much higher under dynamic heating than under isothermal heating. The reaction order (n) of OMMT was lower than those of SEBS and their composites. The obtained TG profiles and calculated kinetic parameters indicated that the incorporation of OMMT into SEBS significantly improved the thermal stability both under dynamic heating and under isothermal heating. The simultaneously obtained DSC data showed that the enthalpy of thermal decomposition decreased with OMMT loading. No significant change in the nonisothermal and isothermal stability of the nanocomposites with addition of SEBS‐g‐MA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal characterizations of semi‐interpenetrating polymer networks composed of poly(ethylene oxide) and poly(N‐isopropylacrylamide)

Poly(N‐isopropylacrylamide) (PNIPAAm)/poly(ethylene oxide) (PEO) semi‐interpenetrating polymer networks (semi‐IPNs) synthesized by radical polymerization of N‐isopropylacrylamide (NIPAAm) in the presence of PEO. The thermal characterizations of the semi‐IPNs were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). The melting temperature (T_m) of semi‐IPNs appeared at around 60°C using DSC. DEA was employed to ascertain the glass transition temperature (T_g) and determine the activation energy (E_a) of semi‐IPNs. From the results of DEA, semi‐IPNs exhibited one T_g indicating the presence of phase separation in the semi‐IPN, and T_gs of semi‐IPNs were observed with increasing PNIPAAm content. The thermal decomposition of semi‐IPNa was investigated using TGA and appeared at around 370°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3922–3927, 2003     

Preparation and characterization of poly(silyl ester)s containing 2,2‐bis(p‐dimethylsiloxy‐phenyl)propane units in the polymer backbones

The two poly(silyl ester)s containing 2,2‐bis(p‐dimethylsiloxy‐phenyl)propane units in the polymer backbones have been prepared via polycondensation reaction of di‐tert‐butyl adipate and di‐tert‐butyl fumarate with 2,2‐bis(p‐chloro dimethylsiloxy‐phenyl)propane to give tert‐butyl chloride as the condensate. The polymerizations were performed under nitrogen at 110°C for 24 h without addition of solvents and catalysts to obtain the poly(silyl ester)s with weight average molecular weights typically ranging from 5000 to 10,000 g/mol. Characterization of the poly(silyl ester)s included ¹H NMR and ¹³C NMR spectroscopies, infrared spectroscopy, ultraviolet spectroscopy, differential scanning calorimetry, thermogravimetric analysis (TGA), gel permeation chromatography, and Ubbelohde viscometer. The glass transition temperatures (T_g) of the obtained polymers were above zero because of the introducing 2,2‐bis(p‐dimethylsiloxy‐phenyl)propane units in the polymer backbones. The TGA/DTG results showed that the obtained poly(silyl ester)s were stable up to 180°C and the residual weight percent at 800°C were 18 and 9%, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1937–1942, 2006     

Thermal degradation of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) as studied by TG,TG–FTIR,and Py–GC/MS

The thermal degradation kinetics of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [poly(HB–HV)] under nitrogen was studied by thermogravimetry (TG). The results show that the thermal degradation temperatures (T_o, T_p, and T_f) increased with an increasing heating rate (B). Poly(HB–HV) was thermally more stable than PHB because its thermal degradation temperatures, T_o(0), T_p(0), and T_f(0)—determined by extrapolation to B = 0°C/min—increased by 13°C–15°C over those of PHB. The thermal degradation mechanism of PHB and poly(HB–HV) under nitrogen were investigated with TG–FTIR and Py–GC/MS. The results show that the degradation products of PHB are mainly propene, 2‐butenoic acid, propenyl‐2‐butenoate and butyric‐2‐butenoate; whereas, those of poly(HB–HV) are mainly propene, 2‐butenoic acid, 2‐pentenoic acid, propenyl‐2‐butenoate, propenyl‐2‐pentenoate, butyric‐2‐butenoate, pentanoic‐2‐pentenoate, and CO₂. The degradation is probably initiated from the chain scission of the ester linkage. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1530–1536, 2003     

Influence of the short‐chain branch length on the calibration of temperature rising elution fractionation systems

The effects of short‐chain branch (SCB) length on the calibration of temperature rising elution fractionation (TREF) were examined. Samples of ethylene–hexene, ethylene–octene, and a novel polyolefin produced using Eastman Chemical Company's Gavilan catalyst technology were used to prepare TREF calibration curves. Preparative TREF was used to collect fractions of the materials based on their crystallizability, and the branching frequencies of the fractions were determined by NMR. Calibration curves were generated by plotting the branching frequency as a function of the TREF elution temperature. The results indicate that the calibration curves shift to lower TREF elution temperatures as the length of the SCB increases from methyl to butyl to hexyl. Other factors that may contribute to this shift include chain microstructural differences from variations in catalyst structure and process conditions. The shift can be decreased by plotting the data in “number of branches per 1000 backbone carbons” versus TREF elution temperature instead of the more traditional “number of branches per 1000 total carbons.” These data indicate that the branch type must be known a priori to calculate SCB averages and SCB distributions and that unique calibration curves exist for copolymers made using different α‐olefin comonomers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 722–728, 2003     

Melt rheology of poly(ϵ‐caprolactone)/poly(styrene‐co‐acrylonitrile) blends

Dynamic viscoelastic properties for miscible blends of poly(?‐caprolactone) (PCL) and poly(styrene‐co‐acrylonitrile) (SAN) were measured. It was found that the time–temperature superposition principle is applicable over the entire temperature range studied for the blends. The temperature dependency of the shift factors a_T can be expressed by the Williams–Landel–Ferry equation: log a_T = ?8.86(T ? T_s)/(101.6 + T ? T_s). The compositional dependency of T_s represents the Gordon–Taylor equation. The zero‐shear viscosities are found to increase concavely upward with an increase in weight fraction of SAN at constant temperature, but concavely downward at constant free volume fraction. It is concluded that the relaxation behavior of the PCL/SAN blends is similar to that of a blend consisting of homologous polymers. It is emphasized that the viscoelastic functions of the miscible blends should be compared in the iso‐free volume state. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2037–2041, 2001     

Study of the compositional heterogeneity of ethylene/1–hexene copolymers produced over supported catalysts of different composition

Separation into narrow MWD fractions (liquid–liquid fractionation) and preparative TREF (temperature rising elution fractionation) with subsequent analysis of fractions by GPC, FTIR, and ¹³C NMR spectroscopy were used to study the comonomer distribution of ethylene/1–hexene copolymers produced over highly active supported titanium‐ and vanadium‐magnesium catalysts (TMC and VMC) and a supported zirconocene catalyst. These catalysts produce PE with different MWD: M_w/M_n values vary from 2.9 for zirconocene catalyst, 4.0 for TMC, and 15 for VMC. 1‐Hexene increases polydispersity to 25 for copolymer produced over VMC and hardly affects MWD of the copolymer produced over TMC and zirconocene catalysts. The most broad short chain branching distribution (SCBD) was found for ethylene/1–hexene copolymers produced over TMC. VMC and supported zirconocene catalyst produce copolymers with uniform profile of SCB content vs. molecular weight in spite of great differences in M_w/M_n values (22 and 2.5 respectively). TREF data showed that majority of copolymer produced over supported zirconocene catalyst was eluted at 70–90°C (about 85 wt %). In the case of VMC copolymer's fractions were eluted in the broad temperature interval (40–100°C). Accordingly, TREF data indicate a more homogeneous SCBD in copolymer, produced over supported zirconocene catalyst. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis functional poly(carbonate‐b‐ester) copolymers and micellar characterizations

Functional poly(carbonate‐b‐ester)s were synthesized in buck by ring‐opening polymerization of the carbonate (TMC, MBC, or BMC) with tert‐butyl N‐(2‐hydroxyethyl) carbamate as an initiator, and then with ε‐CL (or ε‐BCL) comonomer. Subsequently, the PMMC‐b‐PCL with pendent carboxyl groups and the PTMC‐b‐PHCL with pendent hydroxyl groups were obtained by catalytic debenzylation. DSC analysis indicated that only one T_g at an intermediate temperature the T_gs of the two polymer blocks. A decrease T_g was observed when an increase contents of ε‐CL incorporated into the copolymers. In contrast, two increased T_ms were observed with increasing PCL content. The block copolymers formed micelle in aqueous phase with critical micelle concentrations (cmcs) in the range of 2.23–14.6 mg/L and with the mean hydrodynamic diameters in the range of 100–280 nm, depending on the composition of copolymers. The drug entrapment efficiency and hydrolytic degradation behavior of micelle were also evaluated. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Kinetics of thermal degradation of thermotropic poly(p‐oxybenzoate‐co‐ethylene‐2,6‐naphthalate) by single heating rate methods

The kinetics of thermal degradation of thermotropic liquid crystalline poly(p‐oxybenzoate‐co‐ethylene‐2,6‐naphthalate) (PHB/PEN) with the monomer ratio of 60 : 40 and PEN in nitrogen was studied by dynamic thermogravimetry (TG). The kinetic parameters, including the activation energy E_a, the reaction order n, and the frequency factor ln(Z) of the degradation reaction for PHB/PEN (60 : 40) and PEN were analyzed by the single heating rate methods of Friedman and Chang. The effects of the heating rate and the calculating method on the thermostable and degradation kinetic parameters are systematically discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91:3915–3920, 2004     

Effect of radiation dose on the thermal degradation of poly(ethylene terephthalate) fabric

The effect of radiation dose (10–30 kGy) on the thermal decomposition of poly(ethylene terephthalate) was studied using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and X‐ray diffraction (XRD) analysis. The TGA and DSC were carried out in a flowing nitrogen atmosphere at heating rates of 5 and 30°C/min for TGA and 10°C/min for DSC. The degradation process was composed of three overlapping stages. The second stage, at which a rapid degradation occurs, was studied in detail. The process was found to follow a second‐order kinetics and was independent of radiation dose or heating rate. The reaction rate constant (k) was found to depend on the heating rate and iradiation dose. The apparent activation energy (Q) and the logarithm of the preexponential rate constant (log A) were found to decrease linearly with the increase in dose at rates of 3.32 kJ mol^?1 kGy^?1 and 0.177 s^?1 kGy^?1 with intercepts of 249 kJ/mol and 12.26 s^?1 for Q and log A of unirradiated fabric, respectively. A direct relationship was found between the percentage decrease in Q and log A and the percentage decrease in the temperature corresponding to 50% conversion (T_50%) for samples irradiated at different doses. It was found that a decrease in T_50% by 1% resulted in a decrease in Q and log A by 1.855 and 2.1%, respectively. Changes in Q and log A resulting from radiation, mechanical and thermal treatments, or their combinations can be predicted from the shift in T_50%. The history of the fibers substantially affected the thermal properties. DSC and XRD studies revealed changes in the fabric crystallinity. DSC measurements indicated a linear increase in heat of fusion with dose increase at a rate of 0.855 kJ kg^?1 kGy^?1. XRD analysis confirmed structural changes, rearrangement by plane rotations, and formation of compact crystalline lattice with patterns characterizing irradiated samples. An attempt to explain the dependency of the apparent activation energy on dose was given. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3710–3720, 2004     

Thermal characteristics and pyrolysis of methyl‐di(phenylethynyl)silane resin

Thermal stability of a recently synthesized polymeric methyl‐di(phenylethynyl)silane (MDPES) resin was studied using a number of thermal and spectrometric analytical techniques. The polymer exhibits extremely high thermal stability. Thermogravimetric analysis (TGA) shows that the temperature of 5% weight loss (T_d5) was 615°C and total weight loss at 800°C was 8.9%, in nitrogen atmosphere, while in air, T_d5 was found to be 562°C, and total weight loss at 800°C was found to be 55.8% of the initial weight. Differential thermal degradation (DTG) studies show that the thermal degradation of MDPES resin was single‐stage in air and two‐stage in nitrogen. The thermal degradation kinetics was studied using dynamic TGA, and the apparent activation energies were estimated to be 120.5 and 114.8 kJ/mol in air, respectively, by Kissinger and Coats–Redfern method. The white flaky pyrolysis residue was identified to be silicon dioxide by FTIR and EDS, indicating that the thermal stability of polymer may be enhanced by the formation of a thin silicon dioxide film on the material surface. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 103: 605–610, 2007     

Preparation of drug‐loaded microspheres of linear and star‐shaped poly(D,L‐lactide)s and their drug release behaviors

Linear (1‐arm) and star‐shaped (4‐, 6‐, and 16‐arm) poly(D,L ‐lactide)s (PDLLs) were synthesized by ring‐opening polymerization in bulk of D,L ‐lactide monomer. Hydroxyl end‐group compounds and stannous octoate were used as the initiator and catalyst, respectively. The intrinsic viscosity and glass transition temperature (T_g) of the PDLLs decreased steadily as the branch arm number increased for similar molecular weights. However, the intrinsic viscosity and T_g values of the linear PDLL were less than the star‐shaped PDLL for similar each PDLL arm lengths. Ibuprofen, a poorly water soluble model drug was entrapped in the PDLL microspheres. All drug‐loaded PDLL microspheres were prepared by the oil‐in‐water emulsion solvent evaporation method, were spherical in shape, and had a smooth surface with fine dispersibility. In vitro drug release behaviors indicated that the drug release from the microspheres with higher branch arm number was faster than from those with lower branch arm number. Moreover, the drug release from the star‐shaped PDLL microspheres was slower than that of the linear PDLL microspheres for similar PDLL arm lengths. The drug release behavior could be adjusted through both the branch arm number and arm length of PDLL. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Star‐shaped POSS–methacrylate copolymers with phenyl–triazole as terminal groups,synthesis, and the pyrolysis analysis

Star‐shaped polyhedral oligomeric silsesquioxane (POSS)–methacrylate hybrid copolymers with phenyl–triazole as terminal groups had been designed and synthesized via sequential atom transfer radical polymerization (ATRP), azidation, and phenylacetylene‐terminated procedures, and the hybrid copolymers here could be denoted as POSS–(PXMA‐Pytl)₈, where X can be M, B, L, and S, represented four different methacrylate monomers, such as methacrylate (MMA), butyl methacrylate (BMA), lauryl methacrylate (LMA), and stearyl methacrylate (SMA), respectively. Thermal gravimetric analysis (TGA) and in situ Fourier transform infrared spectroscopy (FTIR) were applied for studying the thermal stability and degradation mechanism, and it was found that all of the POSS–(PXMA‐Cl)₈ and POSS–(PXMA‐Pytl)₈ copolymers exhibited excellent thermal stabilities, which had great potential in heat‐resistant material application. Different tendencies of decomposition temperatures at 5% and 10% weight loss (T₅ and T₁₀) dependent on the side‐chain length and terminal group species were investigated respectively. The longer alkyl side chains of the monomers, the lower thermal stabilities, and enhanced T₅ and T₁₀ were also shown with the introduction of phenyl–triazole groups instead of chlorine groups. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40652.     

Thermal characteristics of interpenetrating polymer networks composed of poly(vinyl alcohol) and poly(N‐isopropylacrylamide)

Interpenetrating polymer networks (IPNs) composed of poly(vinyl alcohol) (PVA) and poly(N‐isopropylacrylamide) (PNIPAAm) were prepared by the sequential‐IPN method. The thermal characterization of the IPNs was investigated using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depression of the melting temperature (T_m) of the PVA segment in IPNs was observed with increasing PNIPAAm content using DSC. DEA was employed to ascertain the glass‐transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_g values, indicating the presence of phase separation in the IPNs. The thermal decomposition of IPNs was investigated using TGA and appeared at near 200°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 881–885, 2003     

Microstructure and melting behavior of a solution‐cast polylactide stereocomplex: Effect of annealing

The effect of annealing on the microstructure and melting behavior of a solution‐cast polylactide (PLA) stereocomplex (sc) was systematically investigated by differential scanning calorimetry and small‐angle X‐ray scattering. A preorder state, an intermediate form between the amorphous and crystalline states, was found in the solution‐cast poly(l ‐lactide)–poly(d ‐lactide) blend. When the annealing temperature (T_a) was below 220 °C, a part of the preorder state directly formed thicker sc crystallites; these corresponded to the second melting peak, which appeared around 250 °C during the heating process. Although the rest melted and became the amorphous phase, it formed a thinner lamella under the restriction of the unmelted initial sc crystallites during annealing; the melting process of this lamella was parallel to that of the new melting peak, which appeared around 220 °C. The melting of the initial crystal formed as the solvent volatilized corresponded to the range of the first melting temperature around 230 °C. When T_a was above 220 °C, the preorder state melted completely, and the initial crystal experienced perfection process. Furthermore, the highest melting temperature of PLA sc (254.1 °C, with a fusion enthalpy of 125.5 J/g) was obtained when T_a was 235 °C. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44626.     

Preparation and characterization of the copolymer containing N‐pyridyl bi(methacryl)imide unit

The copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide was prepared based on the reaction of polymethacrylic acid with 2‐pyridylamine. The molecular structure was characterized by ¹H‐NMR, FTIR, UV–Vis, and circular dichroism techniques. The physical properties of polymethacrylic acid change significantly after an introduction of 6 mol % N‐2‐pyridyl bi(methacryl)imide unit. In particular, the thermal degradation of the polymer was systematically studied in flowing nitrogen and air from room temperature to 800°C by thermogravimetry at a constant heating rate of 10°C/min. In both atmospheres, a four‐stage degradation process of the copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide was revealed. The initial thermal degradation temperature T_d, and the first, second, and third temperatures at the maximum weight‐loss rate T_dm1, T_dm2, and T_dm3 all decrease with decreasing sample size or changing testing atmosphere from nitrogen to air, but the fourth temperature at the maximum weight‐loss rate T_dm4 increases. The maximum weight‐loss rate, char yield at elevated temperature, four‐stage decomposition process, and three kinetic parameters of the thermal degradation were discussed in detail. It is suggested that the copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide exhibits low thermal stability and multistage degradation characteristics. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1673–1678, 2002     

Kinetics of thermal degradation of nanometer calcium carbonate/linear low‐density polyethylene nanocomposites

To improve the thermal properties of linear low‐density polyethylene (LLDPE), the CaCO₃/LLDPE nanocomposites were prepared from nanometer calcium carbonate (nano‐CaCO₃) and LLDPE by melt‐blending method. A series of testing methods such as thermogravimetry analysis (TGA), differential thermogravimetry analysis, Kim‐Park method, and Flynn‐Wall‐Ozawa method were used to characterize the thermal property of CaCO₃/LLDPE nanocomposites. The results showed that the CaCO₃/LLDPE nanocomposites have only one‐stage thermal degradation process. The initial thermal degradation temperature T₀ increasing with nano‐CaDO₃ content, and stability of LLDPE change better. The thermal degradation activation energy (E_a) is different for different nano‐CaCO₃ content. When the mass fraction of nano‐CaCO₃ in nanocomposites is up to 10 wt %, the nanocomposite has the highest thermal degradation E_a, which is higher (28 kJ/mol) than pure LLDPE. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characteristics of a novel aliphatic polycarbonate,poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)]

A novel aliphatic polycarbonate, poly[(propylene oxide)‐co‐(carbon dioxide)‐co‐(γ‐butyrolactone)] [P(PO? CO₂? GBL)], was synthesized by the copolymerization of carbon dioxide, propylene oxide (PO) and γ‐butyrolactone (GBL). The resulting copolymers were determined by FTIR and NMR spectral analysis with viscosity‐average molecular weights (M_v) from 50 000 to 120 000 g mol^?1. According to elemental analysis, the calculated data of elemental contents in P(PO? CO₂? GBL)44 were close to the found data. The result showed that GBL was inserted into the backbone of poly[(propylene oxide)‐co‐(carbon dioxide)] successfully. GBL offered an ester structural unit that gave the copolymer better degradability. The correlations between reaction conditions and properties were studied. When GBL content increased, the M_v and the glass transition temperature (T_g) of the copolymers improved relative to an identical copolymer without GBL. Prolonging the reaction time of the copolymerization resulted in increases in M_v and T_g. P(PO? CO₂? GBL) exhibited a high T_g above 40 °C. The rate of backbone degradation increased with increasing GBL content. Copyright © 2005 Society of Chemical Industry