Preparation and characterization of graphene composites with conducting polymers

We report a new route for preparing electro‐conductive composites based on reduced graphene oxide (RG‐O) and poly(3,4‐ethylenedioxythiophene) (PEDOT). The composites were prepared by in situ polymerization of EDOT in aqueous mixture containing RG‐O platelets modified with poly(sodium 4‐styrenesulfonate) (PSS). In the synthetic process, PSS molecules stabilize RG‐O in the aqueous phase and function as a polymerization template to hybridize PEDOT chains along RG‐O platelets. Compared with the RG‐O platelets, the resulting composites show an enhanced electrical conductivity of 9.2 S cm^?1 with good thermal stability. Copyright © 2011 Society of Chemical Industry     

NIPAM改性PEDOT:PSS导电聚合物的制备及在电致变色器件中的应用

以柔性疏水小分子N-异丙基丙烯酰胺（NIPAM）对聚苯乙烯磺酸盐（PSS）进行共聚改性，制备了一系列聚[(苯乙烯磺酸盐)-共-异丙基丙烯酰胺][P(SS-co-NIPAM)]，并以其为模板采用氧化聚合法与3,4-乙烯二氧噻吩（EDOT）制备了导电聚合物PEDOT:P(SS-co-NIPAM)。与PEDOT:PSS薄膜相比，NIPAM摩尔分数（以对苯乙烯磺酸钠物质的量为基准，下同）为15%时，PEDOT:P(SS-co-NIPAM)薄膜平均透光率保持在80%左右，水接触角从18.5°增至39.0°，疏水性提高，并且弯曲1000次后方阻变化量为5.71 kΩ/sq，远小于PEDOT:PSS薄膜（10.60 kΩ/sq）。以NIPAM摩尔分数为15%的PEDOT:P(SS-co-NIPAM)薄膜作为离子储存层的电致变色器件的光学对比度（ΔT）为9.83%，循环800次后ΔT仍达到9.55%，衰减量为0.28%，衰减量与PEDOT:PSS器件相当，说明NIPAM共聚改性能改善PEDOT:PSS导电聚合物的柔韧性和疏水性，以其作为离子储存层的器件可维持优异的电致变色性能。     

Dextrin‐ and Conducting‐Polymer‐Containing Biocomposites: Properties and Behavior as Cellular Matrix

Both α‐cyclodextrin and linear dextrin are used to prepare biocomposites with poly(3,4‐ethylenedioxythiophene). Materials are prepared electrochemically in aqueous solution. Comparison with the pure polymer indicates that the electroactivity and electrostability decrease with the incorporation of the dextrins while the electrical conductivity is retained. The different properties of the two biocomposites suggest that the linear dextrin is mainly located at the surface, whereas the cyclodextrin is homogeneously distributed in the polymeric matrix. Cell adhesion and proliferation assays indicate that the cellular activity is significantly higher in the dextrin‐containing biocomposites.

     

Preparation of cardanol based epoxy plasticizer by click chemistry and its action on poly(vinyl chloride)

In recent years, the using of reproducible resource and economical and efficient synthesis method has got wide concern. Herein, an environmental‐friendly plasticizer originated from cardanol was synthesized by click chemistry. First, the cardanol sulfide (CS) was obtained by click chemistry reaction between the double bond of the side chain of cardanol and mercaptoethanol. The degree of the click reaction was estimated to reach 84.7% by testing the content of sulfur. Then, the epoxidation of the hydroxyl was performed to get cardanol based epoxy plasticizer (CEP) in the presence of epichlorohydrin. The epoxy value was 0.32. The structure of CS and CEP was confirmed by FT‐IR and NMR techniques. A Haake torque rheometer was used to research the action of CEP on polyvinyl chloride (PVC). Results showed that it possessed favorable plasticization effect and stabilization effect on PVC. CEP had good heat stabilization in PVC, and could decrease the T_g of PVC significantly. Moreover, CEP could increase the tensile strength of PVC when in a small amount, and could increase the plasticity of PVC when in a larger quantity significantly. The characteristics of volatile, migration and solvent extraction of PVC plasticized by CEP is similar to by dioctyl phthalate (DOP). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44890.     

Synthesis and characterization of greenish‐blue emitting vinyl copolymer containing pyrene and triarylamine moieties

Two fluorescent monomers N‐phenyl‐N‐(4‐vinylphenyl)pyren‐1‐amine (vinyl‐PyPA) and 1‐vinyl pyrene (VPy) were synthesized in good yields. A series of soluble conductive vinyl copolymers P(PyPA‐co‐VPy) containing vinyl‐PyPA and VPy moieties in different composition ratios were prepared by free radical solution polymerization. These copolymers showed high T_g (190?201 °C) and good thermal stability. The photoluminescence emission maxima of the copolymers were all in the range 474.5?478.5 nm, which was similar to the poly(N‐phenyl‐N‐(4‐vinylphenyl)pyren‐1‐amine) (P(PyPA)) (475 nm) but blue shifted compared with poly(1‐vinyl pyrene) (PVPy) (490.5 nm). The lifetime of the copolymers increased from 10.2 to 29.7 ns with an increase in pyrene content. The copolymers had higher quantum yields (0.51) than those of the homopolymers of P(PyPA) (0.48) and PVPy (0.13). The highest occupied molecular orbital of the copolymers remained relatively unchanged from P(PyPA), while the lowest unoccupied molecular orbital varied from ?2.41 eV to ?2.51 eV with an increase in pyrene ratio in the copolymers. The energy bandgaps of the copolymers (from 2.70 eV to 2.81 eV) were smaller than those of P(PyPA) (2.82 eV) and PVPy (3.47 eV). Two polymer light‐emitting diode (PLED) series were attempted including indium tin oxide (ITO) (fluorocarbon (CFx) treated)/P(PyPA‐co‐VPy)/LiF/Al and ITO(CFx treated)/P(PyPA‐co‐VPy)/1,3,5‐Tri(1‐phenyl‐1H‐benzo[d]imidazol‐2‐yl)phenyl (TPBi)/LiF/Al. The results suggested that the PyPA moiety is hole conducting and the PLEDs can achieve high luminance from 650 to 1150 cd m^?2 (at 100 mA cm^?2) only when an electron injecting layer TPBi is employed. © 2013 Society of Chemical Industry     

Effects of alcoholic solvents on the conductivity of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs)

The effects of alcoholic solvents on the charge transport properties of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs) are investigated. The use of different alcoholic solvents in the oxidative chemical polymerization of 3,4‐ethylenedioxythiophene (EDOT) with iron(III)‐p‐tosylate led to a change in the electrical conductivity of PEDOT‐OTs. For example, PEDOT‐OTs prepared from methanol shows a conductivity of 20.1 S cm^?1 which is enhanced by a factor of 200 as compared to PEDOT‐OTs prepared from hexanol. The variation of charge transport properties on the use of different alcoholic solvents is consistent with the data recorded by UV‐visible and electrospin resonance (ESR) measurements. From XPS experiments, the PEDOT‐OTs samples prepared from different alcoholic solvents were found to have almost the same doping level, suggesting that the number of charge carriers is not responsible for the change in conductivity. Supported by XRD results, it was found that the use of alcoholic solvents with shorter chain length induces more efficient packing of PEDOT chains. It is proposed that the alcoholic solvents associated with the counter ion of PEDOT via hydrogen bonding give rise to a change in the molecular ordering of PEDOT chains during the polymerization step, hence enhancing or depressing the inter‐chain hopping rate of the resulting PEDOT‐OTs. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of new poly(amide‐imide)s based on 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene

A series of new aromatic poly(amide‐imide)s were synthesized by the triphenyl phosphite‐activated polycondensation of the diimide‐diacid, 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The poly(amide‐imide)s had inherent viscosities of 0.88–1.27 dL g⁻¹. The diimide‐diacid monomer (I) was prepared from 2,5‐dichloro‐p‐phenylenediamine with trimellitic anhydride. All the resulting polymers were amorphous and were readily soluble in a variety of organic solvents, including NMP and N,N‐dimethylacetamide. Transparent, flexible, and tough films of these polymers could be cast from N,N‐dimethylacetamide or NMP solutions. Cast films had tensile strengths ranging from 92 to 127 MPa, elongations at break from 4 to 24%, and initial moduli from 2.59 to 3.65 GPa. The glass transition temperatures of these polymers were in the range of 256°–317°C, and the 10% weight loss temperatures were above 430°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 271–278, 1999     

Characteristics of dual‐type electrochromic devices based on poly(ethylene oxide) copolymers

Dual‐type polymer electrochromic devices based on [(3‐thienyl)methylmethacrylate]‐co‐[p‐vinyl benzyloxy poly(ethylene oxide)]/polythiophene and thiophene‐capped poly(ethylene oxide)/polythiophene and ethylene dioxythiophene were constructed via electropolymerization. Spectroelectrochemistry, switching ability and stability of the devices were investigated using UV‐visible spectrophotometry and cyclic voltammetry. These devices exhibit low switching voltages and short switching times with reasonable switching stability under atmospheric conditions. Copyright © 2006 Society of Chemical Industry     

Synthesis of poly(3,4‐ethylenedioxythiophene) nanoparticles via chemical oxidation polymerization

Poly(3,4‐ethylenedioxythiophene) (PEDOT) nanoparticles were synthesized via chemical oxidation polymerization using 3,4‐ethylenedioxythiophene as the starting monomer and ammonium peroxydisulfate (APS) as the oxidant. The effects of APS concentration, surfactant concentration and type of surfactant, namely dodecylbenzenesulfonic acid and sodium dodecylsulfate, were investigated. Distinct particle shapes were obtained: irregular, raspberry agglomerate, coralliform, orange‐peel, globular and plum shapes. The particle sizes and the electrical conductivity are in the ranges 60 to 900 nm and <1 to 153 S cm^?1, respectively, depending on the polymerization conditions. PEDOT synthesis in the absence of a surfactant yields a smaller particle size because a larger amount of initiator induces lower molecular weights and smaller PEDOT particles. The smaller PEDOT particles correspond to higher electrical conductivity because of the larger surface areas for electron transfer and a smaller amount of obstructing surfactant aliphatic segments. Moreover, particle size and shape can be varied, depending on surfactant type and concentration which dictate the micellar shapes in the polymerization reaction. This work is focused on the tailor‐made PEDOT shape and property relationship under synthesis conditions where several shapes have not been previously seen. © 2013 Society of Chemical Industry     

Generating Power Enhancement of Flexible PVDF Generator by Incorporation of CNTs and Surface Treatment of PEDOT:PSS Electrodes

Two approaches are proposed for enhancing the generating power of polyvinylidene fluoride (PVDF) flexible generator by incorporating carbon nanotubes (CNTs) and ethylene glycol (EG) treatment of the poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) electrodes. By incorporating CNTs into the PVDF polymer, higher portion of β‐phase PVDF can be obtained, which shows higher piezoelectricity resulting in higher electric charge generating performance. Higher conductivity is also obtained by surface treatment of the PEDOT:PSS electrodes using EG solvent due to the removal of excess PSS in the electrodes. Highly conductive electrode makes effective mobility of charges generated from the CNT/PVDF film, resulting in higher generating performance. Consequently, higher generating performance can be achieved by collaborating the above two approaches.     

Methylmethacrylate polymerization photoinitiated by 1‐(bromoacetyl)pyrene

The photopolymerization of methylmethacrylate induced by pyrene, 1‐acetylpyrene (AP), and 1‐(bromoacetyl)pyrene (BP) has been investigated. Under all conditions employed, pyrene was completely ineffective. Introduction of a carbonyl and a bromo group in pyrene enhanced the polymerization efficiencies. Efficiency of AP as photoinitiator was very low; however, BP was proved to be a good photoinitiator. The polymerization with BP follows first‐order kinetics with respect to monomer conversion, with a shorter induction period as compared with that of AP. The value of the initiator exponent (0.5) and the linear dependence of reciprocal average degree of polymerization on the square root of the initiator concentration suggest radical polymerization with bimolecular termination. IR and NMR spectra showed the atactic nature of polymethylmethacrylate. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 920–926, 2006     

Sustainable Polymers from Renewable Resources: Polymer Blends of Furan‐Based Polyesters

A series of blends of furan‐based green polyesters, for eco‐friendly packaging materials, are synthesized. Poly(ethylene 2,5‐furandicarboxylate) (PEF), poly(propylene 2,5‐furandicarboxylate) (PPF), and poly(butylene 2,5‐furandicarboxylate) (PBF) are synthesized by applying melt polycondensation. Blends of the above polyesters with 50/50 w/w composition as well as blends of furanoate/terephthalate (PPF/PPT) are also prepared. The glass temperature along with the crystallization and melting behaviors of melt quenched blends are studied aiming at understanding their dynamic state and miscibility. Based on their T_g and crystallization behavior, PEF/PPF shows dynamic homogeneity and miscibility whereas PPF/PBF and PEF/PBF exhibit partial miscibility and immiscibility, respectively. In an effort to dynamically homogenize the compounds, reactive blending is applied and the behavior of the resulting blends is monitored following quenching. A profound improvement in blend homogenization is observed with increasing melt mixing time for the PPF/PPT sample, evidenced by the single glass temperature and by the narrowing in liquid‐to‐glass regime. The obtained single glass temperature together with the suppressed tendency for crystallization with increasing mixing time are taken as evidences of dynamic and thermodynamic homogeneity.     

Preparation and properties of electrically conducting textiles by in situ polymerization of poly(3,4‐ethylenedioxythiophene)

Poly(3,4‐ethylenedioxythiophene) (PEDOT) was in situ polymerized on nylon 6, poly(ethylene terephthalate) (PET), and poly(trimethylene terephthalate) (PTT) fabrics using ferric p‐toluenesulfonic acid (FepTS) and ferric chloride (FeCl₃) as oxidants. The effect of the organic solvents used in the polymerization bath was investigated. Prepared PEDOT/nylon 6 composite fabrics have superior electrical conductivity (0.75 S/cm, in ethanol solvent) compared to those of the other PEDOT composite fabrics. In particular, after five cycles of polymerization, the electrical conductivity of the composite fabric reached about 2 S/cm. However, the nylon 6 fabric was damaged by EDOT radical cations and the strong acidity of FepTS during the polymerization process. It was concluded that PTT fabric, which has excellent elastic recovery and acid resistance, is a suitable substrate for in situ polymerization of PEDOT, because the PEDOT/PTT composite fabric was hardly damaged during the polymerization process and its electrical conductivity is comparatively good (0.36 S/cm, in butanol solvent). © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1326–1332, 2005     

Synthesis and characterization of polymers derived from selenophene

The synthesis of poly(2,5‐selenophen‐oxo‐1,4‐phenylen‐selenide‐1,4‐phenylene‐oxo) (I) and poly(2,5‐selenophen‐oxo‐1,4‐phenylen‐diselenide‐1,4‐phenylen‐oxo) (II) by reaction of 2,5‐bis(1,4‐bromo‐phenylen‐oxo‐)‐selenophene with sodium selenide or diselenide, respectively, using dimethylformamide as solvent, is described. Both monomers and polymers were characterized by elemental analysis, melting point, and FTIR spectroscopy. Polymers I and II were doped with iodine and SbF₅ and characterized by SEM and XPS. Also, the conductivity and the T_g values were determined. For both polymers the best doping agent was iodine, although polymer II always presented higher conductivity, reaching values of about 6 · 10^?9 S · cm^?1. The T_g values suggest a likely crosslinking of the chains in polymer II when doped with SbF₅. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2019–2026, 2001     

Electrochemical immobilization of ascorbate oxidase in poly(3,4‐ethylenedioxythiophene)/multiwalled carbon nanotubes composite films

Immobilization of ascorbate oxidase (AO) in poly(3,4‐ethylenedioxythiophene) (PEDOT)/multiwalled carbon nanotubes (MWCNTs) composite films was achieved by one‐step electrochemical polymerization. The PEDOT/MWCNTs/AO modified electrode was fabricated by the entrapment of enzyme in conducting matrices during electrochemical polymerization. The PEDOT/MWCNTs modified electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The experimental results showed that the composite films exhibited better mechanical integrity, electrochemical activity, higher electronic and ionic conductivity, and larger redox capacitance compared with pure PEDOT films, which would be beneficial to the fabrication of PEDOT/MWCNTs/AO electrochemical biosensors. The scanning electron microscopy studies revealed that MWCNTs served as backbone for 3,4‐ethylenedioxythiophene (EDOT) electropolymerization. Furthermore, the resulting enzyme electrode could be used to determine L ‐ascorbic acid successfully, which demonstrated the good bioelectrochemical catalytic activity of the immobilized AO. The results indicated that the PEDOT/MWCNTs composite are a good candidate material for the immobilization of AO in the fabrication of enzyme‐based biosensor. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of electroactive films based on benzo(a)pyrene

The polycyclic aromatic hydrocarbons (PAHs) are a group of compounds that might have practical applications due to their graphene-like properties. Derivatized PAHs can self-assemble in liquid crystal form. The chemical synthesis of large size PAHs can however be complicated and problematic. Electrochemical synthesis of PAHs molecules was studied in this work by cyclic voltammetry. Benzo(a)pyrene was used as the monomer. The resulting electroactive films consist of different PAHs in both size and symmetry. We call this mixture poly(benzopyrene) (PBP). The synthesis conditions of PBP were optimized to obtain thick and electrochemically stable films. The best film quality was achieved by potential scanning in propylene carbonate at low scan rate resulting in continues polymer growth during 10 scans giving approx. a 1 μm thick PBP film. During p- and n-doping studies the reduction and oxidation peaks were observed at 1.0 V and −1.6 V, respectively, with an electrochemical band gap of approx. 2.6 eV. The in situ UV–vis characterization of the PBP films was made by applying a constant potential with increasing steps. The optical band gap was approx. 2.5 eV and the absorption maximum was observed at ca. 420 nm. During p- and n-doping new induced bands were formed in the range 575–600 nm. UV–vis spectroscopy indicate that PBP mainly consist of units consisting of more than 40 carbon atoms and large number of π-electrons.     

New developments in macroinorganics — the thermodynamics of basic polymers

The protonation and complex formation of some basic polymers have been studied in aqueous solution by potentiometric, calorimetric, spectrophotometric and viscosimetric techniques. Specific methods for the treatment of either ‘sharp’ or ‘apparent’ thermodynamic functions in polyelectrolyte bearing one or two basic groups in the repeating unit have been developed. The results are related to structure features and presence of various types of chemical function besides the aminic function.     

Studies on blends of LLDPE and polar polymers compatibilized by a random copolymer

Compatibilization of blends of linear low‐density polyethylene (LLDPE)–poly(methyl methacrylate) (PMMA) and LLDPE–copolymer of methyl methacrylate (MMA) and 4‐vinylpyridine (poly(MMA‐co‐4VP) with poly(ethylene‐co‐methacrylic acid) (EMAA) have been studied. Mechanical properties of the LLDPE–PMMA blends increase upon addition of EMAA. In order to further improve interfacial adhesion of LLDPE and PMMA, 4‐vinyl pyridine units are introduced into PMMA chains, or poly(MMA‐co‐4VP) is used as the polar polymer. In LLDPE–poly(MMA‐co‐4VP)–EMAA blends, interaction of MAA in EMAA with 4VP of poly(MMA‐co‐4VP) causes a band shift in the infrared (IR) spectra. Chemical shifts of N_1s binding energy in X‐ray photoelectronic spectroscopy (XPS) experiments indicate a transfer of proton from MAA to 4VP. Scanning electron microscopy (SEM) pictures show that the morphology of the blends were improved upon addition of EMAA. Nonradiative energy transfer (NRET) fluorescence results attest that there exists interdiffusion of chromophore‐labeled LLDPE chains and chromophore‐labeled poly(MMA‐co‐4VP) chains in the interface. Based on experimental results, the mechanism of compatibilization is studied in detail. Compatibilization is realized through the interaction between MAA in EMAA with 4VP in poly(MMA‐co‐4VP). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 967–973, 1999     

Chemosynthesis and characterization of fully biomass‐based copolymers of ethylene glycol, 2,5‐furandicarboxylic acid,and succinic acid

Poly(ethylene 2,5‐furandicarboxylate‐co‐ethylene succinate) (PEFS) copolymers of 2,5‐furandicarboxylic acid (FDCA) and succinic acid with 11.98–91.32 mol % FDCA composition were synthesized via melt polycondensation in the presence of ethylene glycol using tetrabutyl titanate as a catalyst. PEFSs' molecular weight, thermal properties, and molar composition were determined by Fourier transform infrared spectroscopy, gel permeation chromatography, intrinsic viscosity, ¹H NMR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and wide‐angle X‐ray diffraction (WAXD) measurements. From experimental conditions, we obtained random copolymers with number‐average molecular weights exceeding 25,600, determined by GPC and ¹H NMR analyses. DSC analysis revealed that PEFS copolymers' melting temperatures differed depending on EF units' percentage. TGA studies confirmed that all PEFS copolymers' thermal stability exceeded 300°C. From WAXD analysis, it is observed that the PEFS copolymer crystal structure was similar to that of PES when EF unit was 11.98 mol % and to that of PEF when EF units were 74.35 and 91.32 mol %. These results benefit this novel biodegradable copolymer to be used as a potential biomaterial. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1415‐1420, 2013