Synthesis of azo‐functionalized ion‐imprinted polymeric resin for selective extraction of nickel(II) ions

The work presented involved the fabrication and evaluation of an ion‐imprinted azo‐functionalized phenolic resin for selective extraction of Ni²⁺ ions from aqueous media. The azo‐containing ligand was first synthesized by coupling of a p‐aminophenol diazonium salt with resorcinol. The ligand was coordinated with Ni²⁺ ion template before condensation polymerization with formaldehyde and resorcinol was performed. The Ni²⁺ ions were extracted from the crosslinked resin matrix to finally afford the Ni²⁺ ion‐imprinted Ni‐PARF adsorbent. The synthetic steps were extensively investigated using elemental analysis and Fourier transform infrared, NMR and energy‐dispersive X‐ray spectroscopies. Also, the surface morphologies along with the surface areas of the adsorbent resin were evaluated using scanning electron microscopy and Brunauer–Emmett–Teller techniques, respectively. Batch experiments indicated that the pseudo‐second‐order kinetic equation provided the best fit with the experimentally obtained kinetic data and equilibrium was reached after 40 min. The isotherm studies were also in a good fit with the Langmuir model and the maximum adsorption capacities of Ni²⁺ ions with respect to both Ni‐PARF and control non‐imprinted C‐PARF adsorbents were around 260 and 100 mg g^?1, respectively. In the presence of Co²⁺, Cu²⁺, Zn²⁺ and Pb²⁺ as competing coexisting ions, the relative selectivity coefficients of Ni‐PARF for Ni²⁺ were, respectively, 84.91, 44.97, 30.41 and 32.20. Regeneration experiments indicated that after eight adsorption/desorption cycles, the Ni‐PARF adsorbent still maintained around 97% of its initial efficiency. © 2018 Society of Chemical Industry     

Preparation of functionalized ion‐imprinted phenolic polymer for efficient removal of copper ions

In this work, an ion‐imprinted polymeric material based on functionalized phenolic resin was developed for the efficient selective removal of Cu²⁺ ions from aqueous solution. p‐Aminophenol‐isatin Schiff base ligand (HPIS) was first synthesized and combined with Cu²⁺ ions to prepare the corresponding complex [Cu(PIS)₂]. The Schiff base ligand along with its copper complex was fully investigated and characterized before anchoring in a base‐catalyzed condensation copolymerization with formaldehyde and resorcinol. The Cu²⁺ ions were removed from the obtained resin construction and the resulting Cu²⁺ ion‐imprinted material (Cu‐PIS) was employed for the selective extraction of Cu²⁺ ions under different pH values, initial concentrations and contact time conditions. The optimum pH for the removal process was chosen as 6 and the maximum adsorption capacity was 187 ± 1 mg g^–1. Also, the kinetics showed a better fit with the pseudo‐second‐order equations. The selectivity of the prepared Cu‐PIS was also evaluated in a multi‐ionic species containing Ni²⁺, Cd²⁺, Pb²⁺, Co²⁺ besides Cu²⁺ ions and the determined parameters confirmed a superior recognition capability toward the imprinted Cu²⁺ ions. © 2019 Society of Chemical Industry     

Binding behavior of Fe3+ ions on ion‐imprinted polymeric beads for analytical applications

We used a molecular imprinting approach to achieve specific metal binding utilizing N‐methacryloyl‐(L )‐cysteine methyl ester (MAC) as a metal‐complexing ligand. MAC was synthesized using methacryloyl chloride and cysteine methyl ester. Then, Fe³⁺ was complexed with MAC monomer. Fe³⁺‐imprinted poly(hydroxyethyl methacrylate‐N‐methacryloyl‐(L )‐cysteine methyl ester) [poly(HEMA‐MAC)] beads with average size of 63–140 μm were produced by suspension polymerization. After that, the template ions (i.e. Fe³⁺ ions) were removed by 0.1M HCl. Fe³⁺‐imprinted beads were characterized by swelling studies, FTIR, and elemental analysis. The Fe³⁺‐imprinted beads with a swelling ratio of 72%, and containing 3.9 mmol MAC/g were used in the binding of Fe³⁺ ions from aqueous solutions, tap water, certified reference serum sample, and real serum sample. Maximum binding capacity, optimum pH, and equilibrium binding time were 107 μmol/g, pH 3.0, and 30 min, respectively. It was observed that even in the presence of other ions, Fe³⁺‐imprinted beads selectively bound Fe³⁺ ions with 97% efficiency. Removal of Fe³⁺ ions from certified reference serum sample was approximately found to be 33%. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3520–3528, 2006     

Synthesis of ion‐imprinting chitosan/PVA crosslinked membrane for selective removal of Ag(I)

A novel ion‐imprinted membranes were synthesized for selective removal and preconentration for Ag(I) ions from aqueous solutions. The membranes were obtained via crosslinking of chitosan (CS), PVA, and blend chitosan/PVA using glutaraldehyde (GA) as crosslinker. The FTIR spectra were used to confirm the membrane formation. Comparing with the nonimprinted membranes, Ag(I)‐imprinted CS and CS/PVA has higher removal capacity and selectivity for Ag⁺ ions. An enhancement in the Ag⁺ removal capacity by ～ 20% (from 77.8 to 94.4 mg g^–1) and ～ 50% (from 83.9 to 125 mg g^–1) was found in the Ag(I)‐imprinted CS and Ag(I)‐imprinted CS/PVA membranes, respectively, when compared with the nonimprinted membranes. Removal equilibra was achieved in about 40 min for the non‐ and ion‐imprinted CS/PVA. The pH and temperature significantly affected the removal capacity of ion‐imprinted membrane. The relative selectivity coefficient values of Ag⁺/Cu²⁺ and Ag⁺/Ni²⁺ are 9 and 10.7 for ion‐imprinted CS membrane and 11.1 and 15 for ion‐imprinted CS/PVA membrane when compared with nonimprinted membranes. The imprinted membranes can be easily regenerated by 0.01M EDTA and therefore can be reused at least five times with only 15% loss of removal capacity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Terpolymer resin II: Synthesis,characterization, and ion‐exchange properties of 2,4‐dihydroxyacetophenone–dithiooxamide–formaldehyde terpolymers

Terpolymers have been prepared by the condensation of 2,4‐dihydroxyacetophenone (2,4‐HA) and dithiooxamide (D) with formaldehyde (F) in the presence of hydrochloric acid as catalyst with varying the molar proportions of the reactant. Compositions of the terpolymer have been determined by elemental analysis. The number average molecular weight has been determined by conductometric titration in nonaqueous medium. Intrinsic viscosities of the solution of the terpolymer have been determined in N,N‐dimethyl formamide (DMF). The terpolymers have been characterized by UV–visible, IR, and proton NMR spectra. Chelation ion‐exchange properties have also been studied employing the batch equilibrium method. It was employed to study selectivity of metal ion uptake over a wide pH range and in media of various ionic strength. The overall rate of metal uptake follows the order: Fe³⁺ > Cu²⁺ > Ni²⁺ > Co²⁺ = Zn²⁺. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Separation and recovery of gold(III) from base metal ions using melamine–formaldehyde–thiourea chelating resin

Melamine–formaldehyde–thiourea (MFT) chelating resin has been prepared. Au³⁺ ions uptake behavior and selectivity of the chelating resin were investigated by both batch and column methods. MFT resin showed higher affinity toward Au³⁺ compared with base metal ions, Cu²⁺ and Zn²⁺. The highest Au³⁺ uptake values were obtained at pH 2 and Au³⁺ adsorption capacity of the resin was calculated as 48 mg Au³⁺/g resin (0.246 mmol Au³⁺/g resin) by batch method. It was concluded that Au³⁺ ions could be selectively concentrated from the solution including Cu²⁺ and Zn²⁺ base metal ions by column method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nickel(II)‐imprinted monolithic columns for selective nickel recognition

Ni²⁺‐imprinted monolithic column was prepared for the removal of nickel ions from aqueous solutions. N‐Methacryloyl‐L ‐histidine was used as a complexing monomer for Ni²⁺ ions in the preparation of the Ni²⁺‐imprinted monolithic column. The Ni²⁺‐imprinted poly(hydroxyethyl methacrylate‐N‐methacryloyl‐L ‐histidine) (PHEMAH) monolithic column was synthesized by bulk polymerization. The template ion (Ni²⁺) was removed with a 4‐(2‐pyridylazo) resorcinol (PAR):NH₃? NH₄Cl solution. The water‐uptake ratio of the PHEMAH–Ni²⁺ monolith increased compared with PHEMAH because of the formation of nickel‐ion cavities in the polymer structure. The adsorption of Ni²⁺ ions on both the PHEMAH–Ni²⁺ and PHEMAH monoliths were studied. The maximum adsorption capacity was 0.211 mg/g for the PHEMAH–Ni²⁺ monolith. Fe³⁺, Cu²⁺, and Zn²⁺ ions were used as competitive species in the selectivity experiments. The PHEMAH–Ni²⁺ monolithic column was 268.8, 25.5, and 10.4 times more selective than the PHEMAH monolithic column for the Zn²⁺, Cu²⁺, and Fe³⁺ ions, respectively. The PHEMAH–Ni²⁺ monolithic column could be used repeatedly without a decrease in the Ni²⁺ adsorption capacity. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

High‐retention properties for Hg(II) ions of a resin containing ammonium and pyridine groups

The metal‐ion uptake behavior of the chelating resin poly([(3‐(methacryloylamino)propyl] trimethyl ammonium chloride‐co‐4‐vinyl pyridine) has been investigated. The resin is obtained by radical copolymerization in a yield of 99.6%. The hydrophilic resin shows a high retention capacity and selectivity toward Hg(II) ions in the presence of Cu(II), Pb(II), Cd(II), Zn(II), and Cr(III) ions. A retention of Hg(II) higher than 99% is observed after 5 min. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2595–2599, 2002     

Syntheses and adsorption properties for Hg2+ of chelating resin of crosslinked polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole

A novel chelating resin with functional group containing S and N atoms was prepared using chloromethylated polystyrene and 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT) as materials. Its structure was characterized by infrared spectra and elementary analysis. The results showed that the content of the functional group was 2.07 mmol BMT g^?1 resin, 47% of which were in the form of monosubstitution (PS‐BMT‐1) and 53% in the form of double substitution (PS‐BMT‐2). The adsorption for mercury ion was investigated. The adsorption dynamics showed that the adsorption was controlled by liquid film diffusion. Increasing the temperature was beneficial to adsorption. The Langmuir model was much better than the Freundlich model to describe the isothermal process. The adsorption activation energy (E_a), ΔG, ΔH, and ΔS values calculated were 18.56 kJ·mol^?1, ‐5.99 kJ·mol^?1, 16.38 kJ·mol^?1, and 37.36, J·mol^?1·K^?1, respectively. The chelating resin could be easily regenerated by 2% thiourea in 0.1 mol·L^?1 HCl with higher effectiveness. Five adsorption–desorption cycles demonstrated that this resin was suitable for repeated use without considerable change in adsorption capacity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1646–1652, 2004     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Preparation and characterization of selective phenyl thiosemicarbazide modified Au(III) ion‐imprinted cellulosic cotton fibers

In this study, a novel selective Au(III) chelating surface ion imprinted fibers based on phenyl thiosemicarbazide modified natural cotton (Au‐C‐PTS) has been synthesized, and applied for selective removal of Au(III) from aqueous solutions. Batch adsorption experiments were performed with various parameters, such as contact time, pH, initial Au(III) concentration, and temperature. The kinetic studies revealed that the adsorption process could be described by pseudo‐second‐order kinetic model, while the adsorption data correlated well with the Langmuir and Freundlich models. The maximum adsorption capacities calculated from the Langmuir equation are 140 ± 1 mg g^?1 and 72 ± 1 mg g^?1 at pH 5 for both Au‐C‐PTS and NI‐C‐PTS, respectively. The estimated thermodynamic parameters (Gibbs free energy (ΔG°), enthalpy (ΔH°), and entropy change (ΔS°)) indicated the spontaneity and exothermic nature of the adsorption process. Furthermore, the selectivity study revealed that the ion imprinted fibers was highly selective to Au(III) compared with Cu(II), Cd(II), Hg(II), and Fe(III). The adsorbent was successfully regenerated with a 0.1M HNO₃ solution. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40769.     

Using a water‐soluble melamine‐formaldehyde resin to improve the hardness of Norway spruce wood

Samples of Norway spruce wood were impregnated with a water‐soluble melamine formaldehyde resin by using short‐term vacuum treatment and long‐term immersion, respectively. By means of Fourier transform infrared (FTIR) spectroscopy and UV microspectrophotometry, it was shown that only diffusion during long‐term immersion leads to sufficient penetration of melamine resin into the wood structure, the flow of liquids in Norway spruce wood during vacuum treatment being greatly hindered by aspirated pits. After an immersion in aqueous melamine resin solution for 3 days, the resin had penetrated to a depth > 4 mm, which, after polymerization of the resin, resulted in an improvement of hardness comparable to the hardwood beech. A finite element model describing the effect of increasing depth of modification on hardness demonstrated that under the test conditions chosen for this study, a minimum impregnation depth of 2 mm is necessary to achieve an optimum increase in hardness. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1900–1907, 2004     

Preparation and characterisation of a novel copper‐imprinted polymer based on β‐cyclodextrin copolymers for selective determination of Cu2+ ions

A novel ion‐imprinted polymer (IIP) using (6‐O‐butene diacid ester)‐β‐cyclodextrin (β‐CD‐MAH) as the functional monomer and copper ions as the template was developed for Cu²⁺ sensing. First, reactive β‐cyclodextrin (β‐CD) monomers with vinyl carboxylic acid functional groups were synthesised and were co‐polymerised with styrene via radical polymerisation. Then, the β‐CD copolymers were complexed with Cu²⁺ in order to obtain the IIP. The imprinting effect was realised by removing the template ions from the imprinted polymer. The structure, composition and morphology of the IIP were characterised by Fourier transform IR spectroscopy, energy‐dispersive spectroscopy and field‐emission SEM. The adsorption capacity was investigated by UV–visible spectroscopy in batch operation mode. The maximum adsorption capacity for the Cu²⁺ template ions was 28.91 mg g^?1, and the adsorption selectivity was clearly illustrated from the increased sorption affinity towards Cu²⁺ ions over other competing ions. The adsorption was affected by the pH of the aqueous medium, and enhanced adsorption capacity was observed at pH 5. The prepared IIP could be used 10 times after its regeneration without significant loss of the adsorption capacity. © 2018 Society of Chemical Industry     

Synthesis and characterization of a drug‐delivery system based on melamine‐modified poly(vinyl acetate‐co‐maleic anhydride) hydrogel

Three‐dimensional polymeric networks, which quickly swell by imbibing a large amount of water or deswell in response to changes in their external environment, are called hydrogels. These types of polymeric materials are good potential candidates for drug‐delivery systems. In this study, we first synthesized poly(vinyl acetate‐co‐maleic anhydride) by free‐radical copolymerization. Then, they were modified with different molar ratios of melamine to prepare hydrogels that could be used in drug‐delivery systems. The hydrogels were characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, differential scanning calorimetry, and scanning electron microscopy. In the second step, Ceftazidime antibiotic was loaded on selected hydrogels. The in vitro drug release was investigated and compared in three different media (HCl solution at pH = 3 and buffer solutions at pH 6.1and pH 8). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40389.     

Preparation and modification of macroporous epoxy‐triethylenetetramine resin for preconcentration and removal of Hg(II) in aqueous solution

A novel macroporous resin was prepared from epoxy resin and triethylenetetramine through a polymerization with phase separation. In this experiment, the polyethylene glycol (PEG‐1000) plays a very important part. It was used as solvent, as phase‐separation reagent in the preparation processes, and as the pore‐forming reagent through removing PEG‐1000 from polymer by water‐cleaning process after completing polymerization. The prepared resin was modified by carbon bisulfide and soaked in 1 mol L^?1 NaOH. Its structure was characterized by Fourier transform‐infrared spectra, scanning electron microscopy, and elemental analysis. The adsorption characteristic of the chelating resin was studied by series of experiments. The results show that the chelating resin possesses excellent adsorption characteristic toward trace Hg(II). The recovery can come to 100% when the concentration of Hg(II) is only 0.05 ppm, and the average maximum adsorption capacity of the chelating resin for Hg(II) is 122 mg g^?1. The precision (relative standard deviation) for six replicate adsorbent extraction of 0.01 μg mL^?1 Hg(II) was 1.1%. The accuracy of the proposed procedure was verified by analyzing a standard reference material. Moreover, the chelating resin was applied to two natural samples and also got satisfactory results. That is to say, the chelating resin modified by carbon bisulfide exhibits a high chelating ability toward Hg(II) and can be used as adsorbent for preconcentration and removal of trace Hg(II) in aqueous solution. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:2372–2378, 2006     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

New melamine–formaldehyde–ketone polymers. III. Coatings from melamine and reactive solvents based on cyclohexanone

The conditions and methods of preparing novel melamine–formaldehyde–cyclohexanone coatings are presented. The coatings were prepared by dissolving melamine in reactive solvents based on formaldehyde and cyclohexanone. The latter were prepared at different molar ratios of the components. The water resistance of the resulting coatings was measured. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1083–1092, 2006