Dual pH‐ and temperature‐responsive hydrogels with extraordinary swelling/deswelling behavior and enhanced mechanical performances

pH‐ and temperature‐responsive semi‐interpenetrating nanocomposite hydrogels (NC hydrogels) were prepared with surface‐functionalized graphene oxide (GO) as the crosslinker, N‐isopropylacrylamide (NIPAM) as the monomer, and chitosan (CS) as an additive. The effects of 3‐(trimethoxysilyl)propylmethacrylate‐modified GO sheets and CS content on various physical properties were investigated. Results show that PNIPAM/CS/GO hydrogels undergo a large volumetric change in response to temperature. Swelling ratios of PNIPAM/CS/GO hydrogels are much larger than those of the conventional organically crosslinked PNIPAM hydrogels. The deswelling test indicates that the deswelling rate was greatly enhanced by incorporating CS into the hydrogel network and using the surface‐functionalized GO as the crosslinker. The pH‐sensitivity of PNIPAM/CS/GO hydrogels is evident below their volume phase transition temperature. Moreover, the PNIPAM/CS/GO hydrogels have a much better mechanical property compared with traditional hydrogels even in a high water content of 90%. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41530.     

Preparation and characterization of PAM/SA tough hydrogels reinforced by IPN technique based on covalent/ionic crosslinking

In order to fabricate tough hydrogels with superior formability, polyacrylamide/sodium alginate (PAM/SA) interpenetrating polymer network (IPN) hydrogels were produced with ionically crosslinked SA interpenetrated in covalently crosslinked PAM. TGA results show that the heat resistance of PAM/SA IPN hydrogel is improved as compared to that of the individual component. Swelling studies indicate that increasing either chemical crosslinker content or ionic crosslinking via adding more N,N′‐methylenebisacrylamide (MBA) or SA results in lower ESR. It is concluded by tensile test that loosely crosslinked PAM coupled with tightly crosslinked SA improve mechanical strength for hydrogels based on covalent/ionic crosslinking. PAM/SA hydrogels via “one‐pot” method can form different complex shapes with mechanical properties comparable to conventional double network (DN) gels. The fracture strength of PAM_0.05/SA₂₀ reaches level of MPa, approaching 2.0 MPa. The work strives to provide method to tune mechanical and physical properties for hydrogels, which is hopefully to guide the design of hydrogel material with desirable properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41342.     

Rheological properties of thermoresponsive nanocomposite hydrogels

Highly elastic and robust nanocomposite hydrogels based on N‐isopropylacrylamide (NIPAM) and cationic (3‐acrylamidopropyl) trimethylammonium chloride (AMPTMA) were synthesized by photopolymerization. Nanoscopic clay, laponite XLS, was added in the gels during the synthesis. The effect of a hydrophobic salt, lithium bis(trifluoromethane) sulfonimide (LiNTf₂), and clay content on the viscoelastic properties, swelling ratio, and stiffness of the nanocomposite hydrogels were investigated as a function of temperature. Synthetic clay served as a multifunctional cross‐linker, producing hydrogels with enhanced elastic properties. Anionic NTf₂ binds to the cationic comonomer units and significantly affected the viscoelasticity and thermal properties. DSC measurements showed that the volume phase transition temperature and its enthalpy changed with the clay content and with introducing the cationic comonomer (AMPTMA) in the PNIPAM network. With the addition of either laponite XLS or the comonomer and 5 mM solution of LiNTf₂, a fourfold and fivefold increase in elastic modulus was obtained, respectively, compared to that of the homopolymer PNIPAM hydrogel. With increasing the temperature from 20 to 45°C for the copolymer gel with 10% AMPTMA in 5 mM LiNTf₂, the elastic modulus grew 15 times larger. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43123.     

One-pot preparation of ultrastrong double network hydrogels

A double-network (DN) polyethylene glycol/polyacrylic acid (PEG/PAA) hydrogel with high compressive strength was synthesized by one-pot solution polymerization. The PEG network crosslinked by glutaraldehyde (GA) was fabricated via condensation reaction while the PAA network crosslinked by N,N’-dimethylenebiacrylamide (MBAM) via free-radical polymerization. The components of hydrogel were analyzed with Fourier transform infrared spectroscopy (FTIR). Mechanical strength of PEG/PAA hydrogels was examined, and the results showed that the addition of GA and PEG endowed the DN hydrogel with a high compressive strength of 10.9 MPa in a water content of 90 wt% due to lightly crosslinking and special entangled bundles morphology. Morphological studies showed that the hydrogels exhibited various pore structures when they were synthesized using different molar ratio of GA to PEG. This work provided a simple way to prepare ultrastrong DN hydrogels.     

Near‐Infrared Light‐Triggered Dual Drug Release Using Gold Nanorod‐Embedded Thermosensitive Nanogel‐Crosslinked Hydrogels

Gold nanorod (AuNR)‐embedded poly(N‐isopropylacrylamide) (PNIPAM) hydrogels offer the possibility of achieving near‐infrared (NIR) light‐triggered drug release. In addition, using nanoparticles as a crosslinker can enhance the mechanical properties of PNIPAM hydrogels, and nanoparticle‐crosslinked hydrogels provide an important approach for dual drug release. Here, NIR light‐triggered dual drug release using AuNR‐embedded thermosensitive nanogel‐crosslinked hydrogels is reported for the first time. Two kinds of drugs are encapsulated, one in the nanogel and the other in the hydrogel. The volume phase transition of the PNIPAM hydrogels is induced by NIR light by utilizing the photothermal effect of AuNRs. By changing the number of embedded AuNRs and the intensity of NIR light, the release rate and drug quantity can be adjusted for on‐demand release. Because of its NIR light‐triggering and nanoparticle‐crosslinking capabilities, AuNR‐embedded thermosensitive nanogel‐crosslinked hydrogels may expand the application scope of hydrogels and provide enhanced properties in their applications.     

Fabrication of tough,self-recoverable,and electrically conductive hydrogels by in situ reduction of poly(acrylic acid) grafted graphene oxide in polyacrylamide hydrogel matrix

Developing electrically conductive hydrogels with good electronic properties and excellent mechanical performance is significant to their potential applications. In this article, we present a strategy to fabricate tough, self-recoverable and electrically conductive hydrogels containing reduced graphene oxide (rGO). Poly(acrylic acid) grafted graphene oxide (GO-g-PAA) was synthesized and incorporated into chemically crosslinked polyacrylamide (PAM) networks to obtain GO-g-PAA/PAM hydrogels, which were further treated with ascorbic acid solution at ambient temperature to give rGO-g-PAA/PAM hydrogels. The interfacial interaction between GO/rGO and hydrogel matrix was improved by reversible hydrogen bonds between the grafted PAA chains and PAM matrix. Consequently, both GO-g-PAA/PAM and rGO-g-PAA/PAM hydrogels exhibited improved tensile properties, excellent energy dissipation, and rapid self-recovery. The in situ chemical reduction of GO-g-PAA in hydrogel matrix endowed rGO-g-PAA/PAM hydrogels with satisfactory electrical conductivity and obvious resistance change upon stretching. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48781.     

Preparation and characterization of sodium alginate/poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide)/clay semi-IPN magnetic hydrogels

pH- and temperature-responsive semi-interpenetrating magnetic nanocomposite hydrogels (NC hydrogels) were prepared by using linear sodium alginate (SA), poly(N-isopropylacrylamide) (PNIPAM) and Fe₃O₄ nanoparticles with inorganic clay as an effective multifunctional cross-linker. The effects of cross-linker and SA contents on various physical properties were investigated. The NC hydrogels exhibited a volume phase transition temperature (VPTT) around 32 °C with no significant deviation from the conventional chemically cross-linked PNIPAM hydrogels (OR hydrogels). The swelling ratios of NC hydrogels were much larger than those of OR hydrogels. Moreover, the swelling ratios of NC hydrogels gradually decreased with increasing the contents of clay and increased with increasing the contents of SA. The pH sensitivity of NC hydrogels was evident below their VPTT. The NC hydrogels had a much better mechanical property than the OR hydrogels. The results showed that the incorporation of clay did not affect the saturation magnetization of the hydrogels.     

Ultrastretchable,Super Tough,and Rapidly Recoverable Nanocomposite Double‐Network Hydrogels by Dual Physically Hydrogen Bond and Vinyl‐Functionalized Silica Nanoparticles Macro‐Crosslinking

It remains a challenge to develop tough hydrogels with recoverable or healable properties after damage. Herein, a new nanocomposite double‐network hydrogel (NC‐DN) consisting of first agar network and a homogeneous vinyl‐functionalized silica nanoparticles (VSNPs) macro‐crosslinked polyacrylamide (PAM) second network is reported. VSNPs are prepared via sol‐gel process using vinyltriethoxysilane as a silicon source. Then, Agar/PAM‐SiO₂ NC‐DN hydrogels are fabricated by dual physically hydrogen bonds and VSNPs macro‐crosslinking. Under deformation, the reversible hydrogen bonds in agar network and PAM nanocomposite network successively break to dissipate energy and then recombine to recover the network, while VSNPs in the second network could effectively transfer stress to the network chains grafted on their surfaces and maintain the gel network. As a result, the optimal NC‐DN hydrogels exhibit ultrastretchable (fracture strain 7822%), super tough (fracture toughness 18.22 MJ m^‐3, tensile strength 431 kPa), rapidly recoverable (≈92% toughness recovery after 5 min resting at room temperature), and self‐healable (can be stretched to 1331% after healing) properties. The newly designed Agar/PAM‐SiO₂ NC‐DN hydrogels with tunable network structure and mechanical properties by multi‐bond crosslinking provide a new avenue to better understand the fundamental structure‐property relationship of DN hydrogels and broaden the current hydrogel research and applications.     

Microwave‐assisted preparation of temperature sensitive poly(N‐isopropylacrylamide) hydrogels in poly(ethylene oxide)‐600

In this article, a series of poly(N‐isopropylacrylamide) (PNIPAM)‐based hydrogels were prepared under microwave irradiation using poly(ethylene oxide)‐600 (PEO‐600) as reaction medium and microwave‐absorbing agent as well as pore‐forming agent. All of the temperature measurements, gel fractions, and FTIR analyses proved that the PNIPAM hydrogels were successfully synthesized. Within 1 min, the PNIPAM hydrogel with a 98% yield was obtained under microwave irradiation. The PNIPAM hydrogels thus prepared exhibited controllable properties such as pore size, equilibrium swelling ratios, and swelling/deswelling rates when changing the feed weight ratios of monomer (N‐isopropylacrylamide, NIPAM) to PEO‐600. These properties are well adapted to the different requirements for their potential application in many fields such as biomedicine. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4177–4184, 2006     

Introduction of silica into thermo-responsive poly(N-isopropyl acrylamide) hydrogels: A novel approach to improve response rates

The response rates of novel thermo-responsive poly(N-isopropyl acrylamide) (PNIPAM) hybrid hydrogels are compared to those of conventional chemically crosslinked PNIPAM hydrogels. The former materials were obtained by applying the sol-gel technology, in which the inorganic silica particles act as physical crosslinks for the organic polymer chains, leading to a semi-interpenetrating polymer network structure. In situ modulated temperature DSC shows that the introduction of hydrophilic silica improves the thermal response rate of the hybrid hydrogels to a great extent as compared to aqueous PNIPAM solutions and conventional PNIPAM hydrogels. Ex situ gravimetrical measurements also illustrate that the shrinking/swelling rate of the hybrid hydrogels is largely improved. It is assumed that the uniform distribution of the SiO₂ units, as demonstrated by cryo-field emission scanning electron microscopy, causes the silica to act as nano-sized water reservoirs, which reduce the characteristic diffusion length of water in the PNIPAM matrix so that it can be transported faster within the hybrid PNIPAM nano-composite.     

Study of pH/temperature dual stimuli‐responsive nanogels with interpenetrating polymer network structure

Nanogels with interpenetrating polymer network (IPN) structure based on poly(N‐isopropylacrylamide) (PNIPAM) and poly(acrylic acid) (PAA) were synthesized by in situ polymerization of acrylic acid and N, N′‐methylenebisacrylamide within the PNIPAM nanogels. Their IPN structure was confirmed using transmission electron microscopy after staining by uranyl acetate. The temperature‐ or pH‐dependent hydrodynamic diameters measured using dynamic laser light scattering show that the IPN nanogels have pH and temperature dual stimuli‐responsive properties. As compared to previously reported pH/temperature dual stimuli‐responsive nanogels, these IPN nanogels have the advantage of less mutual interference between the temperature‐responsive and pH‐responsive components, which is beneficial for their applications in controlled drug release and sensors. The temperature‐ and pH‐triggered volume phase transition mechanisms of the IPN nanogels were tested by probing the microenvironment change of their PNIPAM and PAA chains upon phase transition using infrared (IR) absorption spectra measured at different pH values and IR difference spectra obtained by subtracting the IR spectrum obtained before temperature‐induced phase transition from that obtained after phase transition. Copyright © 2012 Society of Chemical Industry     

Temperature and pH effects on the stability and rheological behavior of the aqueous suspensions of smart polymers based on N‐isopropylacrylamide,chitosan, and acrylic acid

This study describes the stability and rheological behavior of suspensions of poly(N‐isopropylacrylamide) (PNIPAM), poly(N‐isopropylacrylamide)‐chitosan (PNIPAM‐CS), and poly(N‐isopropylacrylamide)‐chitosan‐poly(acrylic acid) (PNIPAM‐CS‐PAA) crosslinked particles sensitive to pH and temperature. These dual‐sensitive materials were simply obtained by one‐pot method, via free‐radical precipitation copolymerization with potassium persulfate, using N,N′‐methylenebisacrylamide as a crosslinking agent. Incorporation of the precursor materials into the chemical networks was confirmed by elementary analysis and infrared spectroscopy. The influence of external stimuli such as pH and temperature, or both, on particle behavior was investigated through rheological measurements, visual stability tests, and analytical centrifugation. The PNIPAM‐CS particles showed higher stability in acid and neutral media, whereas PNIPAM‐CS‐PAA particles were more stable in neutral and alkaline media, both below and above the lower critical solution temperature of PNIPAM (stability data). This is due to different interparticle interactions as well as those between the particles and the medium (also evidenced by rheological data), which were also influenced by the pH and temperature of the medium. Based on the results obtained, we found that the introduction of pH‐sensitive polymers to crosslinked PNIPAM particles not only produced dual‐sensitive materials but also allowed particle stability to be adjusted, making phase separation faster or slower, depending on the desired application. Thus, it is possible to adapt the material to different media. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Strain‐induced crystallization behavior of phenolic resin crosslinked natural rubber/clay nanocomposites

Nanocomposites of natural rubber (NR) and unmodified clay were prepared by latex compounding method. Phenolic resin (PhOH) was used to crosslink NR. Crosslinked neat NR was also prepared for comparison. The structure–property relationship of uncrosslinked and crosslinked NR/clay nanocomposites was examined to verify the reinforcement mechanism. Microstructure of NR/clay nanocomposites was studied by using transmission electron microscopic (TEM), X‐ray diffraction (XRD), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering (SAXS) analyses. The results showed the evidence of intercalated clay together with clay tactoids for the nanocomposite samples. The highest tensile strength was achieved for the crosslinked NR/clay nanocomposite. The onset strain of deformation induced the crystallization of NR for nanocomposites was found at almost the same strain, and furthermore their crystallization was developed at lower strain than that of the crosslinked neat NR because of the clay orientation and alignment. However, at high strain region, the collaborative crystallization process related to the clay dispersion and conventional crosslink points in the NR was responsible to considerably high tensile strength of the crosslinked NR/clay nanocomposite. Based on these analyses, a mechanistic model for the strain‐induced crystallization and orientational evolution of a network structure of PhOH‐crosslinked NR/clay nanocomposite was proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42580.     

Synergetic Effects of Graphene Oxide and Clay on the Microstructure and Properties of HIPS/Graphene Oxide/Clay Nanocomposites

In this paper, double-network structure nanocomposite with improved mechanical and thermal properties were prepared using high-impact polystyrene as a matrix phase, clay and graphene oxide as effective reinforcing fillers through a facile solution intercalation method. The structure and morphology of nanocomposites were characterized by transmission electron microscopy, scanning electron microscopy, X-ray diffraction analysis, and the synergetic effects of clay and graphene oxide on the final properties were investigated using tensile, dynamic mechanical thermal analysis (DMTA) and thermogravimetric analysis (TGA) analysis. Mechanical analysis showed that the combination of graphene oxide and clay exerted a favorable synergistic effect on the tensile modulus and the yield strength of the ternary composite that are greatly improved as compared with neat high-impact polystyrene, high-impact polystyrene/graphene oxide, and high-impact polystyrene/clay binary composites due to the double-network structure formation between the nanofillers as confirmed by the direct morphological observations using transmission electron microscopy and scanning electron microscopy analysis. The viscoelastic behavior showed that storage modulus of ternary composite significantly improvement over than that of the pure matrix, high-impact polystyrene/graphene oxide and high-impact polystyrene/clay while network structure made. TGA and DMTA measurements also demonstrated that thermal stability of high-impact polystyrene matrix modified by graphene oxide and clay slightly enhanced during the creation of dual network structure of graphene oxide and clay. Our data suggest a potential application for the combination of graphene oxide and clay in graphene-based composite materials.     

Biocompatible,ionic‐strength‐sensitive,double‐network hydrogel based on chitosan and an oligo(trimethylene carbonate)–poly(ethylene glycol)–oligo(trimethylene carbonate) triblock copolymer

A double‐network (DN) hydrogel was prepared through the sequential photopolymerization of oligo(trimethylene carbonate) (TPT)‐block‐poly(ethylene glycol)‐block‐oligo(trimethylene carbonate) diarylate and methacrylated chitosan (CS–MA). The swelling behavior and mechanical properties of the hydrogels were tunable via the control of the concentration of CS–MA. Under physiological conditions, the fracture stress of the DN hydrogel reached 3.4 MPa; this was more than twice that of the corresponding TPT‐block‐poly(ethylene glycol)‐block‐TPT single network (1.6 MPa). At high ionic strength, the fracture stress of the DN hydrogel reached 6.4 MPa. The DN hydrogel exhibited good cytocompatibility, as revealed by a live–dead assay. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42459.     

Functionalization of hybrid poly(n‐isopropylacrylamide) hydrogels for Escherichia coli cell capture via adsorbed intermediate dye molecule

Poly(n‐isopropylacrylamide) Laponite (PNIPAM‐Lap) hybrid hydrogels, which use the synthetic clay Laponite as a crosslinker, permanently adsorb cationic laser dyes out of solution. This proof‐of‐concept expounds on this capability by adsorbing an intermediate dye molecule and using it as the foundation for successfully conjugating microbial antibodies to the surface of a PNIPAM hydrogel. The study involves using acriflavinium chloride molecules, adsorbed by a PNIPAM‐Lap hydrogel from an acriflavine laser dye solution, as an intermediate molecule to attach antibodies raised against E. coli to the hydrogel and demonstrate cell capture. Furthermore, this system exemplifies a novel biotechnological platform for greatly expanding PNIPAM hydrogels' capabilities and applicability through conjugation chemistry to surface‐bound molecules. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41557.     

聚环氧乙烷对PAMPS/PAM双网络水凝胶结构和性能的影响

采用紫外光引发聚合制备了含聚环氧乙烷（PEO）的聚(2-丙烯酰胺-2-甲基丙磺酸)(PAMPS）/聚丙烯酰胺（PAM）双网络（DN）水凝胶。使用扫描电子显微镜（SEM）观察了PAMPS单网络水凝胶的结构;测定了PEO改性前后双网络水凝胶的压缩及拉伸性能。PEO改性DN凝胶的第一网络网孔上由于PEO片晶结构引起不同程度的褶皱,这种褶皱起支撑作用;PEO的分子量达到5万时,褶皱的支撑作用最佳,DN凝胶的力学性能最佳;DN凝胶的力学性能随PEO加入量先提高后下降,在PEO加入量为0.1%时,PEO片晶结构加固了DN凝胶的物理交联点,力学性能达到最大,压缩应力达到31.6 MPa;加入更多的PEO阻碍了第一网络的凝胶化,造成网络结构的不连续,从而使DN凝胶的力学性能下降。     

Ethanol organosolv lignin as a reactive filler for acrylamide‐based hydrogels

Hydrogels based on acrylamide (AM) and ethanol organosolv lignin (EOL) with high swelling and good mechanically elastic properties were synthesized in an alkaline solution. EOL was used as a reactive filler for the preparation of AM‐based hydrogels. The impact of EOL addition on the physicochemical properties of AM‐based hydrogels was investigated using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy, and their mechanical properties were examined. The water swelling ratio of the prepared hydrogels increased with the increase of EOL content, and their maximum swelling ratio could reach up to 180. Mechanical measurements indicated that their tensile strength was highly dependent on the amount of EOL, and their elongation at break reached up to 1400%. The formation mechanism of EOL composite hydrogels was probably that most of AM was synthesized into the crosslinked poly(acrylic amide) network, and small quantities of AM was hydrolyzed to acrylic acid ions under alkaline condition. The chain transfer of free radicals from AM and/or AA to EOL molecules occurred in the polymerization process. With increasing EOL content in the hydrogels, an interpenetrating polymer network might be mainly formed by the hydrogen bonding between EOL and AA and/or AM molecules. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42638.     

Robust hydrogel of regenerated cellulose by chemical crosslinking coupled with polyacrylamide network

Regenerated cellulose/polyacrylamide (RC/PAAm) double network (DN) hydrogels are composed of cellulose crosslinked by epichlorohydrin (ECH) and chemical-crosslinked PAAm. The prepared RC/PAAm DN hydrogels present enhanced strength, good shape recovery property, excellent energy dissipation properties, decreased equilibrium water content, and low equilibrium swelling ratio (SR). The compressive strength and modulus of RC/PAAm hydrogel are about 4.3 and 11.5 times compared to that of RC hydrogel, respectively. Intriguingly, the chemical crosslinking between ECH and cellulose chains could increase the distance between cellulose chains. Consequently, the increasing molar ratio of ECH to glucose leads to larger SRs and decreased mechanical strength of the hydrogels. Additionally, higher PAAm contents lead to more densely crosslinked networks, and thus decreasing the SRs and improving the mechanical strength of the hydrogels. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47811.     

Preparation and microstructural analysis of poly(ethylene oxide) comb‐type grafted poly(N‐isopropyl acrylamide) hydrogels crosslinked by poly(ϵ‐caprolactone)

Poly(N‐isopropyl acrylamide) (PNIPAAm)‐graft‐poly(ethylene oxide) (PEO) hydrogels crosslinked by poly(?‐caprolactone) diacrylate were prepared, and their microstructures were investigated. The swelling/deswelling kinetics and compression strength were measured. The relationship between the structure and properties of hydrogel are discussed. It was found that the PEO comb‐type grafted structure reduced the thermosensitivity and increased the compression strength. The addition of poly(?‐caprolactone) (PCL) accelerated the deswelling rate of the hydrogels. Meanwhile, the entanglement of PCL chains restrained the further swelling of the network of gels. The PCL crosslinking agent and PEO comb‐type grafted structure made the behavior of the hydrogels deviate from the rubber elasticity equations. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013