Application of polymer gel electrolyte with graphite powder in quasi‐solid‐state dye‐sensitized solar cells

A polymer gel electrolyte with ionic conductivity of 5.11 mS cm⁻¹ was prepared by using poly (acrylonitrile‐co‐styrene) as polymer matrix, acetonitrile and tetrahydrofuran as binary organic mixture solvent, NaI + I₂ as electrolyte, graphite powder and 1‐methylimidazole as additives. The components ratio of the polymer gel electrolyte was optimized, and the influence of the components and temperature on the ionic conductivity of the polymer gel electrolyte and photoelectronic properties of dye sensitized solar cell were investigated. On the basis of the polymer gel electrolyte with the optimized conditions, a quasi‐solid‐state dye‐sensitized solar cell was fabricated and its light‐ to‐electricity energy conversion efficiency of 3.25% was achieved under irradiation of 100 mW cm⁻². POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Exploration on polypropylene carbonate polymer for gel polymer electrolyte preparation and dye‐sensitized solar cell application

Gel polymer electrolytes (GPEs) with incorporation of polypropylene carbonate (PPC) polymer and different weight percentages of sodium iodide (NaI) salt are prepared. Ethylene carbonate and propylene carbonate are used as plasticizers. The maximum ionic conductivity of 2.01 mS cm^?1 is achieved at room temperature. Temperature‐dependent ionic conductivity study is performed. The GPEs are studied for structural properties using Fourier transform infrared (FTIR). The FTIR analysis confirms that complexation between PPC and NaI has occurred. By using GPEs, dye‐sensitized solar cells (DSSC) are fabricated under the one Sun light intensity. The highest energy conversion efficiency of 6.38% is achieved with incorporation of 60 wt % of NaI. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45091.     

Microporous gel electrolyte for quasi‐solid‐state dye‐sensitized solar cell

The extension of electrocatalytic reaction of I^?/I₃^? from counter electrode/gel electrolyte interface to gel electrolyte can significantly enhance the redox kinetics and therefore conversion efficiency of dye‐sensitized solar cells. Microporous gel electrolyte from polypyrrole integrated poly(hydroxyethyl methacrylate/cetytrimethylammonium bromide) [PPy‐integrated poly (HEMA/CTAB)] is successfully synthesized by in‐situ polymerization of pyrrole monomers in three‐dimensional framework of porous poly(HEMA/CTAB) matrix. An ionic conductivity of 12.72 mS cm^?1 and activation energy of 8.65 kJ mol^?1 are obtained from PPy‐integrated poly(HEMA/CTAB) gel electrolyte. Tafel polarization and electrochemical impedance spectroscopy are employed to characterize the electrocatalytic behaviors of the gel electrolytes. The resultant quasi‐solid‐state dye‐sensitized solar cell shows a light‐to‐electrical conversion efficiency of 6.68%. POLYM. ENG. SCI., 54:2531–2535, 2014. © 2013 Society of Plastics Engineers     

Carbon/polymer composite counter‐electrode application in dye‐sensitized solar cells

Carbon black was embedded in mixtures of poly(ethylene oxide) and poly(vinylidene fluoride–hexafluoropropylene) to make a carbon/polymer composite slurry, which was deposited onto a transparent conducting glass substrate by a doctor‐blade coating for application in dye‐sensitized solar cells (DSSCs) as a counter‐electrode (CE) material. The experiments indicated that the photovoltaic parameters of the DSSCs were strongly dependent on the carbon concentration in the slurry. The device with a carbon CE whose mass ratio was 1 : 1 (mass ratio = carbon black mass to polymer mass) exhibited an overall energy conversion efficiency of 4.62%; this was comparable to that of a device with platinum as a CE (5.32%) under the same test conditions. The better electrocatalytic activity of CE‐1.0 (where 1.0 indicates the mass ratio of carbon black to polymer) for the reduction of triiodide resulted a higher performance of the DSSC with such a CE. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Application of thermosetting organic solvent free polymer gel electrolyte in quasi‐solid‐state dye‐sensitized solar cell

A kind of thermosetting organic solvent free polymer gel electrolyte with oligomer ethylene glycol as liquid phase was prepared and applied in quasi‐solid‐state dye‐sensitized solar cell (QS‐DSSC). The viscosity and the ionic conductivity of the polymer gel electrolyte are sensitive to the changed temperature. The photovoltaic performance of QS‐DSSC is also improved with the increased temperature due to the increased ionic conductivity and diffusion coefficient of iodide in polymer gel electrolyte. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Ionic conductivity of solid polymer electrolytes for dye‐sensitized solar cells

We developed an ionic conductivity model of solid polymer electrolytes for dye‐sensitized solar cells (DSSCs) based on the Nernst–Einstein equation in which the diffusion coefficient is derived from the molecular thermodynamic model. We introduced concentration‐dependence of the diffusion coefficient into the model, and the diffusion coefficient was expressed by differentiating the chemical potential by concentration. The ionic conductivities of polymer electrolytes (PEO/LiI/I₂ system) were investigated at various temperatures and compositions. We prepared a set of PEO in which an EO : LiI mole ratio of 10 : 1 was kept constant for PEO·LiI·(I₂)_n compositions with n = 0.02, 0.05, 0.1, 0.15, 0.2, and 0.3 (mole ratio of LiI : I₂). The ionic conductivities of the electrolytes were measured using a stainless steel/polymer‐electrolyte/stainless steel sandwich‐type electrode structure using alternating current impedance analysis. The values calculated using the proposed model agree well with experimental data. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Wire‐shaped,dye‐sensitized solar cells with poly(vinyl alcohol) gel electrolyte and metal filaments

A kind of wire‐shaped, dye‐sensitized solar cell (WDSSC) composed of poly(vinyl alcohol) (PVA) gel electrolyte and filament‐formed electrodes of titanium and platinum was prepared, and its photovoltaic performance was analyzed with the variations in the dimensions of the electrodes and cells. The dimensions of the wire‐shaped cell were adjusted through the thickness of the TiO₂ layer, the amount of PVA gel electrolyte, and length of the Pt filament. The dominant parameters determining the cell performance were mainly analyzed with the results from the various scanning electron microscopy images and fitted plots of electrochemical impedance spectroscopy. Although the conversion efficiencies of the fabricated WDSSCs were relatively lower than those of the conventional dye‐sensitized solar cells, this development should provide important guiding directions for the design of similar WDSSCs with higher efficiencies. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43439.     

Studies of solvent effect on the conductivity of 2‐mercaptopyridine‐doped solid polymer blend electrolytes and its application in dye‐sensitized solar cells

Solvents and electrolytes play an important role in the fabrication of dye‐sensitized solar cells (DSSCs). We have studied the poly(ethylene oxide)‐poly(methyl methacrylate)‐KI‐I₂ (PEO‐PMMA‐KI‐I₂) polymer blend electrolytes prepared with different wt % of the 2‐mercaptopyridine by solution casting method. The polymer electrolyte films were characterized by the FTIR, X‐ray diffraction, electrochemical impedance and dielectric studies. FTIR spectra revealed complex formation between the PEO‐PMMA‐KI‐I₂ and 2‐mercaptopyrindine. Ionic conductivity data revealed that 30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂ electrolyte can show higher conductivity (1.55 × 10^?5 S cm^?1) than the other compositions (20, 40, and 50%). The effect of solvent on the conductivity and dielectric of solid polymer electrolytes was studied for the best composition (30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂) electrolyte using various organic solvents such as acetonitrile, N,N‐dimethylformamide, 2‐butanone, chlorobenzene, dimethylsulfoxide, and isopropanol. We found that ac‐conductivity and dielectric constant are higher for the polymer electrolytes processed from N,N‐dimethylformamide. This observation revealed that the conductivity of the solid polymer electrolytes is dependent on the solvent used for processing and the dielectric constant of the film. The photo‐conversion efficiency of dye‐sensitized solar cells fabricated using the optimized polymer electrolytes was 3.0% under an illumination of 100 mW cm^?2. The study suggests that N,N‐dimethylformamide is a good solvent for the polymer electrolyte processing due to higher ac‐conductivity beneficial for the electrochemical device applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42489.     

Synthesis of quaternized ammonium iodide‐containing conjugated polymer electrolytes and their application in dye‐sensitized solar cells

A series of conjugated polymer electrolytes (CPEs) comprising fluorene/carbazole or thiophene/carbazole backbones with quaternized ammonium iodide groups were synthesized and used in polymer solution and polymer gel electrolytes in dye‐sensitized solar cells (DSSCs). The photovoltaic (PV) performances became markedly poorer with increasing CPE content for the DSSCs based on polymer solution electrolytes. However, the PV performances were not significantly affected with increasing CPE content for the DSSCs fabricated from poly(ethylene oxide) (PEO)/CPE blend‐based gel‐type electrolytes. Moreover, higher PV efficiencies and stabilities were obtained for the DSSCs based on PEO/CPE blend gel electrolytes as compared to the DSSCs based on PEO gel electrolyte. The electrochemical impedance and PV properties of the DSSCs based on polymer solution electrolytes and on polymer gel electrolytes were determined as a function of the CPE concentration. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of poly(1‐vinyl‐3‐propylimidazolium) iodide for quasi‐solid polymer electrolyte in dye‐sensitized solar cells

The synthesis conditions of ionic liquid 1‐vinyl‐3‐propylimidazolium iodide (ViPrIm⁺I⁻) and Poly(1‐vinyl‐3‐propylimidazolium) iodide [P(ViPrIm⁺I⁻)] were studied in this work. P(ViPrIm⁺I⁻) as a single‐ion conductor providing iodine was designed to develop a quasi‐solid polymer electrolyte based on PVDF/PEO film for dye‐sensitized solar cells (DSSCs). The samples were characterized respectively by high‐performance liquid chromatography (HPLC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance imaging (NMRI), gel permeation chromatography (GPC), etc. The results showed that the single‐ion conducting quasi‐solid polymer electrolyte (SC‐QPE) exhibited high ionic conductivity of 1.86 × 10⁻³ S cm⁻¹ at room temperature measured by CHI660C Electrochemical Workstation. Moreover, solar cells assembled using the SC‐QPE yielded an open‐circuit voltage of 0.83V, short‐circuit current of 8.01 mA cm⁻² and the conversion efficiency of 2.42%. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Amelioration of electrochemical and photovoltaic performances on P(VP‐co‐VAc) based gel polymer electrolyte by incorporating double salt for dye‐sensitized solar cells

Dye‐sensitized solar cell (DSSC) is an alternative photovoltaic application used to replace the liquid electrolyte dependent conventional photovoltaic cell. In this research, gel polymer electrolyte (GPE) was used to replace the unstable liquid electrolyte. This GPE consists of poly[1‐vinylpyrrolidone‐co‐vinyl acetate] (P[VP‐co‐VAc]), tetrabutylammonium iodide (TBAI), sodium iodide (NaI), iodine (I₂), ethylene carbonate (EC), and propylene carbonate (PC). The GPE was tested for its ionic conductivity and an optimum level was reached at sample with 30% TBAI and 6% NaI at 1.17 × 10^?3 S cm^?1. The DSSC was then fabricated with all GPEs and a photovoltaic performance study was conducted. As a result, the highest photovoltaic conversion efficiency (PCE), η for a single salt was 3.04% for 40% TBAI. When a second salt is added, the system showed improvement in efficiency, η to 4.54% with short circuit current density, J_sc of 11.02 mA cm^?2 and open circuit voltage, V_oc of 0.67 V and FF of 61%. The other changes after the addition of TBAI and NaI salts have been observed through X‐ray diffraction, Fourier transformation and thermal analysis studies. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43805.     

An ionic liquid‐based polymer with π‐stacked structure as all‐solid‐state electrolyte for efficient dye‐sensitized solar cells

An ionic liquid based polymer, poly(1‐ethyl‐3‐(acryloyloxy)hexylimidazolium iodide) (PEAI), was synthesized and employed as electrolyte to fabricate all‐solid‐state dye‐sensitized solar cells. The photophysical properties of PEAI were studied by UV–vis absorption spectroscopy and photoluminescence spectroscopy. PEAI exhibited significant hypochromism and red shift in UV–vis absorption spectra and large Stokes shifts in photoluminescence spectra, indicating the formation of a novel π‐stacked structure in which the imidazolium rings in the side chain were stacked. Without iodine in its preparation, DSC with PEAI electrolyte achieved a conversion efficiency of 5.29% under AM 1.5 simulated solar light irradiation (100 mW cm^?2). The side‐chain imidazolium π‐π stacking in PEAI played a key role in the holes transport from the photoanode to the counter electrode. Both the open‐circuit voltage and short‐circuit current density showed decreases with the increase in the content of iodine in PEAI electrolyte. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of polyaniline/TiO2 nanocomposite film with good adhesion behavior for dye‐sensitized solar cell application

In this study, novel Polyaniline (PAni)/TiO₂ nanocomposites were applied on fluoride‐doped tin oxide (FTO) glass to act as an efficient counter electrode in dye‐sensitized solar cell (DSSC) application. PAni/TiO₂ nanocomposites were synthesized via chemical oxidation process using di‐2‐ethylhexylsulfosuccinate sodium salt (NaDEHS) as dopant. The nanocomposites were characterized using fourier transform infrared and ultraviolet‐visible spectrometers. In the application of PAni as the counter electrode in the solar cell, the film showed poor adhesion on the FTO glass. Palm oil‐based alkyd was introduced into the nanocomposite mixture to improve the adhesion of the film. The findings in the work show that strong adhesion of PAni on FTO glasses has led to higher incident photon to current conversion efficiency (IPCE) in solar cell. The short circuit current (Jsc), Voc (open circuit voltage), and IPCE of the resulted PAni/TiO₂ counter electrode with good adhesion in DSSC are 15.8 mA/cm², 670 mV, and 3.0%, respectively. POLYM. COMPOS., 34:1884–1891, 2013. © 2013 Society of Plastics Engineers     

Development of quasi‐solid‐state dye‐sensitized solar cell based on an electrospun polyvinylidene fluoride–polyacrylonitrile membrane electrolyte

Dye sensitized solar cell (DSSC) has been magnetizing more awareness in current research due to more efficiency. The foremost drawback of the solar cell is the evaporation of organic electrolyte. In order to address this problem, the polyvinylidene fluoride–polyacrylonitrile–Electrospinning Fibrous Membranes were prepared by electrospinning method and the photovoltaic performances were evaluated. The polyvinylidene fluoride and polyacrylonitrile were mixed in N,N′‐dimethylformamide and acetone at an applied potential of 15 kV. The surface morphology of membrane is interconnected with network structure and a large number of voids were observed from Field Emission Scanning Electron Microscopy images. The electrolyte uptakes up to 310% were observed and it shows an increase in the ionic conductivity up to 6.12 × 10^?2 S cm^?1 at 25°C. The fabricated DSSCs show open circuit voltage (V_oc) of 0.74 V, fill factor (FF) of 0.65 and short circuit current (J_sc) of 6.20 mA cm^?2 at an incident light intensity of 100 mW cm^?2. The photovoltaic efficiency also reached up to 3.09%. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40022.     

Analyses of structurally modified quasi‐solid‐state electrolytes using electrochemical impedance spectroscopy for dye‐sensitized solar cells

Electrochemical properties of structurally modified quasi‐solid‐state electrolytes were examined using porous substrates (PSs). The PS was prepared into two categories by a phase inversion method with a brominated poly(phenylene oxide) (BPPO): the sponge and finger types. Effects of the humidification and cosolvent compositions on the morphology of the PS were analyzed by scanning electron microscopy. In all cases of the PSs, a higher V_OC was observed of about 0.1 V than that of a liquid electrolyte owing to a suppressed back electron charge transfer. In addition, the PS prepared by the polymer solution of 1 : 4 : 1 (BPPO : N‐methyl‐2‐pyrrolidone : butyl alcohol) with the humidification process showed better photovoltaic properties in terms of the current density and conversion efficiency owing to the appropriate combinations of pore size, tortuosity, and interconnectivity. Effects of the pore structures were intensively examined using electrochemical impedance spectroscopy. The impedance results revealed that large pores at the surface layers are advantageous for a lower R_S and R_TiO2. Meanwhile, the straight inner structure is beneficial for the facile I^?/I₃^? diffusion, thus lowering R_Pt. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39739.     

In situ thermal polymerization of an ionic liquid monomer for quasi‐solid‐state dye‐sensitized solar cells

In situ thermal polymerization of a model ionic liquid monomer and ionic liquids mixture to form gel electrolytes is developed for quasi‐solid‐state dye‐sensitized solar cells (Q‐DSSCs). The chemical structures and thermal property of the monomers and polymer are investigated in detail. The effect of iodine concentration on the conductivity and triiodide diffusion of the gel electrolytes is also investigated in detail. The conductivity and triiodide diffusion of the gel electrolytes increase with the increasing I₂ concentration, while excessive I₂ contents will decrease the electrical performances. Based on the in situ thermal polymeric gel electrolytes for Q‐DSSCs, highest power conversion efficiency of 5.01% has been obtained. The superior long‐term stability of fabricated DSSCs indicates that the cells based on in situ thermal polymeric gel electrolytes can overcome the drawbacks of the volatile liquid electrolyte. These results offer us a feasible method to explore new gel electrolytes for high‐performance Q‐DSSCs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42802.     

Recent progress in electrospinning TiO2 nanostructured photo‐anode of dye‐sensitized solar cells

The key to improving the performance of dye‐sensitized solar cells is the photo‐anode that has much dye adsorption and short optoelectronic transmission path. Electrospun TiO₂ films in photo‐anode have high specific surface area and meet the demand exactly. The article summarizes these efforts in TiO₂ photo‐anode improvement, including various morphology, different one‐dimensional and two‐dimensional composite structure, and varied element doped TiO₂ photo‐anode. Besides, the review makes comparison with these different TiO₂ photo‐anodes in photoelectric properties. The conclusions provide a clear guidance in design of morphology, structure, and doping, which is helpful for researcher to improve the performance of the anode and increase the photoelectric conversion efficiency especially those prepared using electrospinning. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45649.     

Poly(methylmethacrylate)—magnesium triflate gel polymer electrolyte for solid state magnesium battery application

A gel polymer electrolyte (GPE) film of poly(methylmethacrylate) and magnesium triflate is studied in view of its potential application in a solid state rechargeable magnesium battery. Experimental data of a.c. impedance and cyclic voltammetric studies of symmetrical cells made of blocking and non-blocking electrodes, and also data of charge/discharge cycles of Mg/GPE/MnO₂ cells are reported. The composition of the GPE is optimized in view of a minimum quantity of the liquid components (propylene carbonate and ethylene carbonate) required for the gel formation and a maximum conductivity. Specific conductivity (σ) of the GPE of optimum composition is (4.2±0.45)×10⁻⁴ S cm⁻¹ at 20 °C. The σ values follow the Arrhenius equation and the activation energy for GPE of optimum composition is 0.038 eV. The effects of temperature and ageing on Mg/GPE interface are studied. Discharge capacity of about 90 mAh g⁻¹ of MnO₂ is obtained during the discharge of Mg/GPE/MnO₂ cells. On repeated charge/discharge cycling of the cell, the discharge capacity decreases to about 70 mAh g⁻¹. The cycle-life is limited by the problems associated with passivation of the Mg surface.     

Effect of sealing with ultraviolet‐curable adhesives on the performance of dye‐sensitized solar cells

In this study, we investigated different types of oligomers, including an aliphatic polyester‐based urethane diacrylate (CN 991) and aliphatic hydrophobic backbone (CN 9014), and different contents of the oligomers and different amounts of 2‐(perfluorohexyl) ethyl methacrylate (PFE) monomer in ultraviolet (UV)‐curable adhesive to explore the effects of their resistance to corrosion on the basis of the electrolyte, adhesion strength, and performance of the sealing of dye‐sensitized solar cells (DSSCs). The DSSCs were sealed with a 58% CN 9014 containing UV‐curable adhesive mixed with 3.0 wt % PFE monomer, which had the greatest open‐circuit voltage and short‐circuit current density. A 4.8% efficiency was obtained after the sample underwent long‐term thermal stability tests at 60°C for 37 days. The performance of the 3.0 wt % PFE‐containing UV‐curable adhesive in the sealing of DSSCs was better than that of Surlyn for long‐term thermal stability. In addition, this adhesive provided better resistance to corrosion because of the electrolyte and enhanced the DSSCs' durability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42015.     

The application of P(MMA-co-MAA)/PEG polyblend gel electrolyte in quasi-solid state dye-sensitized solar cell at higher temperature

A poly(methyl methacrylate-co-methacrylate acid)/poly(ethylene glycol) [P(MMA-co-MAA)/PEG] polyblend with viscoelasticity was synthesized by a copolymerizing reaction between methyl methacrylate (MMA) and methacrylate acid (MAA) using azobisisobutyronitrile (AIBN) as initiator in poly(ethylene glycol) (PEG) methanol solution. Then, a polyblend gel electrolyte was prepared by adding KI and I₂ to P(MMA-co-MAA)/PEG system. The influence of compositions of the polyblend gel electrolyte on the ionic conductivity and the effect of temperature on photoelectronic performance of quasi-solid state dye-sensitized solar cell (QS-DSSC) were discussed. It was found that the polyblend gel electrolyte was a good candidate as high-temperature electrolyte for QS-DSSCs. Under an optimized condition, the highest conductivity of the polyblend gel electrolyte was 2.70 mS/cm² at 30 °C. Based on the polyblend gel electrolyte, a light-to-electricity conversion efficiency of 4.85% for QS-DSSC was achieved under AM 1.5 simulated solar light illumination at 60 °C.