Synthesis and characterization of organo‐soluble poly(ether ether ketone)s and poly(ether ether ketone ketone)s containing pendant pentadecyl chains

Poly(ether ether ketone)s and poly(ether ether ketone ketone)s containing pendant pentadecyl chains were synthesized by polycondensation of each of the two bisphenol monomers viz, 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane and 1,1‐bis(4‐hydroxyphenyl)‐3‐pentadecyl cyclohexane with activated aromatic dihalides namely, 4,4′‐difluorobenzophenone, and 1,3‐bis(4‐fluorobenzoyl)benzene in a solvent mixture of N,N‐dimethylacetamide and toluene, in the presence of anhydrous potassium carbonate. Polymers were isolated as white fibrous materials with inherent viscosities and number average molecular weights in the range 0.70–1.27 dL g^?1 and 76,620–1,36,720, respectively. Poly(ether ether ketone)s and poly(ether ether ketone ketone)s were found to be soluble at room temperature in organic solvents such as chloroform, dichloromethane, tetrahydrofuran, and pyridine and could be cast into tough, transparent, and flexible films from their solutions in chloroform. Wide angle X‐ray diffraction patterns exhibited a broad halo at around 2θ = ～ 19° indicating that the polymers containing pentadecyl chains were amorphous in nature. In the small‐angle region, diffuse reflections of a typically layered structures resulting from the packing of pentadecyl side chains were observed. The temperature at 10% weight loss, obtained from TG curves, for poly(ether ether ketone)s and poly(ether ether ketone ketone)s were in the range 416–459°C, indicating their good thermal stability. A substantial drop in glass transition temperatures (68–78°C) was observed for poly(ether ether ketone)s and poly(ether ether ketone ketone)s due to “internal plasticization” effect of flexible pendant pentadecyl chains. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of novel poly(arylene ether)s based on 9,10‐bis‐(4‐fluoro‐3‐trifluoromethylphenyl) anthracene and 2,7‐bis‐(4‐fluoro‐3‐trifluoromethylphenyl) fluorene

Two new bisfluoro monomers 9,10‐bis‐(4‐fluoro‐3‐trifluoromethylphenyl) anthracene and 2,7‐bis‐(4‐fluoro‐3‐trifluoromethylphenyl) fluorene have been synthesized by the cross‐coupling reaction of 2‐fluoro‐3‐trifluoromethyl phenyl boronic acid with 9,10‐dibromo anthracene and 2,7‐dibromo fluorine, respectively. These two bisfluoro compounds were used to prepare several poly(arylene ether)s by aromatic nucleophilic displacement of fluorine with various bisphenols; such as bisphenol‐A, bisphenol‐6F, bishydroxy biphenyl, and 9,9‐bis‐(4‐hydroxyphenyl)‐fluorene. The products obtained by displacement of the fluorine atoms exhibits weight‐average molar masses up to 1.5 ×10⁵ g mol^?1 and number average molecular weight up to 6.8 × 10⁴ g mol^?1 in GPC. These poly(arylene ether)s show very high thermal stability even up to 490°C for 5% weight loss occurring at this temperature in TGA in synthetic air and showed glass transition temperature observed up to 310°C. All the polymers are soluble in a wide range of organic solvents, e.g., CHCl₃, THF, NMP, and DMF. Films cast from DMF solution are brittle in nature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis of soluble and thermally stable poly[arylene ether amide (N‐arylenebenzimidazole)]s

Poly(arylene ether)s containing N‐arylenebenzimidazole and amide groups were prepared using an aromatic nucleophilic displacement reaction that replaced the N‐H sites from four different bis(benzimidazolyl) derivatives with activated aromatic difluorides containing ether and amide groups in sulfolane. The reaction was carried out at 210 °C in the presence of anhydrous potassium carbonate. The structures of the polymers were characterized by means of Fourier transform infrared, ¹H NMR spectroscopy and elemental analysis, and the results were largely consistent with the proposed structure. All resulting polymers showed an essentially amorphous nature. This was consistent with the calculated results. Differential scanning calorimetry and thermogravimetric measurements showed that the polymers had high glass transition temperatures (>190 °C), good thermostability and high decomposition temperatures (>400 °C). These novel polymers also showed easy solubility. Copyright © 2012 Society of Chemical Industry     

Synthesis and characterization of novel soluble cardo poly(arylene ether ketone)s containing xanthene structures

9,9‐Bis(4‐hydroxyphenyl)xanthene (BHPX), a bisphenol monomer, was synthesized in 82% yield from xanthenone in a one‐pot, two‐step synthetic procedure. Four novel aromatic poly(ether ketone)s (PEKs) based on BHPX were prepared via a nucleophilic aromatic substitution polycondensation with four difluorinated aromatic ketones. The polycondensation proceeded in tetramethylene sulfone in the presence of anhydrous potassium carbonate and afforded the new cardo PEKs in nearly quantitative yields with inherent viscosities of 0.77–0.85 dL/g. High molecular weight PEKs having number‐average molecular weights (M_n's) in the range of 38,900–40,600 g/mol with the polydispersity index ranged from 1.97 to 2.06 are all amorphous and show high glass transition temperatures ranging from 210°C to 254°C, excellent thermal stability, and the temperatures at the 5% weight loss are over 538°C with char yields above 60% at 700°C in nitrogen. These new PEKs are all soluble in polar aprotic solvents such as N‐methyl‐2‐pyrrolidone and N, N′‐dimethylacetamide and could also be dissolved in chloroform and tetrahydrofuran. All the polymers formed transparent, strong, and flexible films with tensile strengths of 78–84 MPa, Young's moduli of 2.54–3.10 GPa, and elongations at break of 14–18 %. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cross-linkable highly halogenated poly(arylene ether ketone/sulfone)s with tunable refractive index: Synthesis, characterization and optical properties

A series of novel cross-linkable, highly halogenated poly(arylene ether ketone)s (HPAEKs) and poly(arylene ether sulfone)s (HPAESs) with different bromine contents have been designed and prepared by polycondensation reactions for use as optical waveguide materials. The method used for their preparation involved reacting decafluorodiphenyl ketone/sulfone (DFPK/DFPS) with a mixture of 4,4′-isopropylidene bis(2,6-dibromophenol) (4Br-BPA), 4,4′-(hexafluoroisopropylidene)diphenol (6F-BPA), and 1,1-bis(4-hydroxyphenyl)ethyl-1-phenyl-2,3,5,6-tetrafluorostyrol ether (BHPFS). The feed ratio of 4Br-BPA to the total bisphenols varied from 0 to 80 mol.%, while that of BHPFS remained at 20% for all polymers. The resulting polymers have excellent solubility in most common organic solvents such as tetrahydrofuran, cyclohexanone and N,N-dimethylacetamide (DMAc) and can be easily cast into optical-quality thin films. A high glass transition temperature in the range of 164-206 °C was found for these polymers, which could be further increased by about 20 °C upon thermal or photochemical cross-linking. Slab and channel waveguides have been prepared from these polymers. All of them exhibited low optical loss (0.4-0.6 dB/cm) at the telecommunication wavelength of 1550 nm. Due to the relatively higher polarizability of the C-Br bond than that of the C-H bond, an increase in the refractive index was observed as the bromine content in the polymers increased. Consequently, the refractive index of HPAEKs and HPAESs can be readily adjusted within a wide range from 1.51 to 1.57 by simply changing the ratio of the bromine-containing bisphenol in the feed. This variability, along with the excellent cross-linking capability, allows these polymers to be used as both the core and the cladding materials for the waveguide device fabrication and provides a greater flexibility in the design of device structures.     

Synthesis and characterization of poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(arylene ether ketone) (S‐PAEK) block copolymers

A series of well‐defined poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(aryl ether ketone) (S‐PAEK) block copolymers of high molecular weights was prepared by direct nucleophilic polymerization of hydroquinone with sodium 5,5′‐carbonylbis(2‐fluorobenzene sulfonate) ( 1 ) and PEKK oligomer ( 2 ). Varying the ratio of 1 to 2 used in polymerization can be used to control the degree of polymer sulfonation, which correspondingly affects the polymer solubility in solvents. Increasing content of 1 in the copolymers, slightly decreases their thermal stability which is nevertheless thermally stable up to 400 °C. Two T_g values, or one broad T_g, were observed in the DSC measurements of the block copolymers, indicating the existence of phase separation, which was further proved by phase‐separated morphologies as shown in atomic force microscopy images. © 2001 Society of Chemical Industry     

含芴可交联聚芳醚酮的合成

以4,4′-二氟二苯甲酮、双酚芴和二烯丙基双酚A为单体,调整双酚芴和二烯丙基双酚A的摩尔比,通过亲核取代逐步加成反应合成了一系列含芴可交联的聚芳醚酮（PAEK）;用红外光谱仪、核磁共振波谱仪、差示扫描量热仪、热重分析仪对所制备的含芴可交联PAEK的结构、热交联行为、热稳定性等进行了表征。结果表明,所制备的聚合物可通过热引发交联,交联后的聚合物具有优良的耐热性能,交联后聚合物的耐溶剂性能得到提高,最高凝胶含量达到97.5 %。     

Synthesis and properties of poly(arylene ether)s based on 3‐pentadecyl 4,4'‐biphenol

A new biphenol, 3‐pentadecyl 4,4′‐biphenol, was synthesized starting from 3‐pentadecylphenol and was polycondensed with 4,4′‐difluorobenzophenone, 1,3‐bis(4‐fluorobenzoyl)benzene and bis(4‐fluorophenyl)sulfone to obtain poly(arylene ether)s with biphenylene linkages in the backbone and pendent pentadecyl chains. Inherent viscosities and number‐average molecular weights (M_n) of the poly(arylene ether)s were in the range 0.50 ? 0.81 dL g^?1 and 2.2 × 10⁴ ? 8.3 × 10⁴, respectively. Detailed NMR spectroscopic studies of the poly(arylene ether)s indicated the presence of constitutional isomerism which existed because of the non‐symmetrical structure of 3‐pentadecyl 4,4′‐biphenol. The poly(arylene ether)s readily dissolved in common organic solvents such as dichloromethane, chloroform and tetrahydrofuran and could be cast into tough, transparent and flexible films from their chloroform solutions. The poly(arylene ether)s exhibited T_g values in the range 35–60 °C which are lower than that of reference poly(arylene ether)s without pentadecyl chains. The 10% decomposition temperatures (T₁₀) of the poly(arylene ether)s were in the range 410–455 °C indicating their good thermal stability. A gas permeation study of poly(ether sulfone) containing pendent pentadecyl chains revealed a moderate increase in permeability for helium, hydrogen and oxygen. However, there was a large increase in permeability for carbon dioxide which could be attributed to the internal plasticization effect of pendent pentadecyl chains. © 2016 Society of Chemical Industry     

Synthesis and characterization of poly(ether amide ether ketone)/poly(ether ketone ketone) copolymers

A new monomer, N,N′‐bis(4‐phenoxybenzoyl)‐m‐phenylenediamine (BPPD), was prepared by condensation of m‐phenylenediamine with 4‐phenoxybenzoyl chloride in N,N‐dimethylacetamide (DMAc). A series of novel poly(ether amide ether ketone) (PEAEK)/poly(ether ketone ketone) (PEKK) copolymers were synthesized by the electrophilic Friedel‐Crafts solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of diphenyl ether (DPE) and BPPD, over a wide range of DPE/BPPD molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The influence of reaction conditions on the preparation of copolymers was examined. The copolymers obtained were characterized by different physicochemical techniques. The copolymers with 10–25 mol % BPPD were semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide linkages in the main chains. The copolymers III and IV with 20–25 mol % BPPD had not only high T_gs of 184–188°C, but also moderate T_ms of 323–344°C, having good potential for the melt processing. The copolymers III and IV had tensile strengths of 103.7–105.3 MPa, Young's moduli of 3.04–3.11 GPa, and elongations at break of 8–9% and exhibited outstanding thermal stability and good resistance to organic solvents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Processable high Tg high strength fluorinated new poly(arylene ether)s containing imido aryl group

A series of poly(arylene ether)s ( 7a–7f ) were successfully synthesized by aromatic nucleophilic substitution reactions of imidoaryl biphenol (5), 4,9‐bis‐(4‐hydroxy‐phenyl)‐2‐phenyl‐benzo[f]isoindole‐1,3‐dione with six different trifluoromethyl substituted bisfluoro monomers ( 6a–6f ). The weight‐average molar masses of the polymers were up to 280 kD as measured by GPC. These poly(arylene ether)s exhibited glass transition temperatures up to 361°C in DSC. These polymers showed very high thermal stability up to 558°C for 10% weight loss under synthetic air in TGA. Except 7d–7f, remaining polymers 7a–7c were soluble in a wide range of organic solvents. Transparent thin films of these polymers cast from DCM or NMP exhibited tensile strengths up to 75 MPa and elongation at break up to 41% depending on their exact repeating unit structures. These poly(arylene ether)s showed cut‐off wavelength in between 400 and 450 nm except 7d and water absorption were in the range of 0.4 to 0.6%. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of novel soluble poly(ether ketone sulfone)s with pendant polychloro groups

A novel monomer of tetrachloroterephthaloyl chloride (TCTPC) was prepared by the chlorination of terephthaloyl chloride catalyzed by ferric chloride at 175–180°C for 10 h and confirmed by FTIR, MS, and elemental analysis. Five new polychloro substituted poly(aryl ether ketone sulfone)s (PEKSs) with inherent viscosities of 0.68–0.75 dL/g have been prepared from 4,4′‐diphenoxydiphenylsulfone, 4,4′‐bis(2‐methylphenoxy) diphenylsulfone, 4,4′‐bis(3‐methylph‐enoxy)diphenylsulfone, 4,4′‐bis(2,6‐dimethylphenoxy)diphenylsulfone, and 4,4′‐bis(1‐naphthoxy)‐diphenylsulfone with TCTPC by electrophilic Friedel‐Crafts acylation in the presence of DMF with anhydrous AlCl₃ as a catalyst in 1,2‐dichloroethane, respectively. These polymers having weight–average molecular weight in the range of 76,600–83,900 are all amorphous and show high glass transition temperatures ranging from 213 to 250°C, the 5% weight loss temperature over 450°C, high char yields of 60–67% at 700°C in nitrogen and good solubility in CHCl₃ and polar solvents such as DMF, DMSO, and NMP at room temperature. All the polymers formed transparent, strong, and flexible films, with tensile strengths of 85.1–90.8 MPa, Young's moduli of 2.52–3.24 GPa, and elongations at break of 21.2–27.2%. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly(arylene ether ketone) (co)polymers containing sulfonate groups

Poly(arylene ether ketone)s containing sulfonate groups were synthesized by aromatic nucleophilic polycondensation of 4,4′-difluorobenzophenone (DFK), sodium 2,5-dihydroxybenzensulfonate (SHQ) and bisphenols. Only low-molecular weight oligomer was obtained when hydroquinone (HQ) was employed as comonomer, while copolymerization of DFK, SHQ, and phenolphthalein (PL) proceeded quantitatively to high-molecular weight (reduced viscosities above 0.68 dL/g) in dimethylsulfoxide at 175 °C in presence of anhydrous potassium carbonate. The sulfonated polymers were soluble in dipolar aprotic solvents, such as N,N-dimethylactamide and N-methyl-2-pyrrolidinone. Tough membranes cast from N,N-dimethylformamide solution with SHQ/DFK mole ratios ≤65:35 were obtained. Both glass transition temperatures and hydrophilicity of the copolymers increased with the content of sodium sulfonate groups. The materials are candidates as new polymeric electrolytes for proton exchange membranes.     

New polymer syntheses: II. Preparation of aromatic poly(ether ketone)s from silylated bisphenols

Bulk condensations of 4,4′-difluorobenzophenone and various silylated bisphenols were carried out at 220°–320°C, with caesium fluoride as catalyst. Silylated bisphenol-A, tetramethylbisphenol-A, 1,1-bis(4-hydroxyphenyl)cyclohexane or 4,4′-dihydroxydiphenylsulphone as monomers and glassy polymers were soluble in several organic solvents. Their glass transitions were determined by differential scanning calorimetry (d.s.c.) and their number molecular weights ($\text{M}\text{?}{}_{\mathrm{<mtext>n</mtext>}}$) determined by means of vapour pressure osmometry. M_n's up to 10 000 were obtained. When silylated hydroquinone, 4,4′-dihydroxydiphenyl, 2,7-dihydroxynaphthalene or 4,4′-dihydroxydiphenylsulphide undergo polycondensation the resulting poly (ether ketone)s form crystals. It is demonstrated that transesterification does not take place and that block copoly(ether ketone-ether sulphone)s are synthesized. Furthermore, the thermostability of the poly(ether ketone)s in air was investigated.     

Synthesis, characterization, and crosslinking of soluble cyano-containing poly(arylene ether)s bearing phthalazinone moiety

A novel series of phthalazinone-based poly(arylene ether nitrile)s bearing terminal cyano groups via N-C linkages (PPEN-DCs) were synthesized by a simple solution polycondensation of 4-(4-hydroxylphenyl)(2H)-phthalazin-1-one (HPPZ) with calculated 2,6-difluorobenzonitrile (DFBN), followed by the termination of 4-chlorobenzonitrile (CBN). The M_ns of oligomeric PPEN-DCs, which are in the range of 1600-6200, can be well-controlled by adjusting reactant ratio. The incorporation of phthalazinone into the polymer chain results in an improvement in the solubility and glass transition temperatures (T_gs). The amorphous PPEN-DCs were thermally crosslinked to afford insoluble products in the presence of terephthalonitrile and zinc chloride. The pendant cyano groups in the polymer chain hardly undergo any crosslinking or cyclization, while the terminal cyano groups with nitrogen-bridged phthalazinone in the para-substitution are much more reactive in s-triazine forming reaction and effectively promote certain crosslinking under normal pressure. T_gs of the oligomers, which range from 245 to 269 °C, could be further increased at least by 94 °C upon thermal curing. The crosslinked samples exhibit excellent thermal stability and absorb less than 2.7 wt% water after exposure to an aqueous environment for extended periods. This kind of cyano-terminated poly(arylene ether nitrile)s may be a good candidate as matrix resins for high-performance polymeric materials.     

Synthesis and characterization of novel (sulfonated) poly(arylene ether)s with pendent trifluoromethyl groups

This paper reports the synthesis of four different trifluoromethyl-substituted poly(arylene ether)s on the basis of 2,2-bis(4-hydroxyphenyl)hexafluoropropane (bisphenol AF) and various difluoro- or dinitrobiphenyl or terphenyl monomers in the course of a step-growth polycondensation. Besides a comparison between the polymerisability of the different monomer combinations, a main focus of this work lies on the NMR characterization of these poly(arylene ether)s. Poly(arylene ether)s with sufficiently high number average molecular weights were sulfonated by fuming sulfuric acid or chlorosulfonic acid and investigated in terms of membrane properties relevant for fuel cell applications.     

Synthesis and characterization of highly soluble poly(ether imide)s containing indane moieties in the main chain

A new indane containing unsymmetrical diamine monomer ( 3 ) was synthesized. This diamine monomer leads to a number of novel semifluorinated poly (ether imide)s when reacted with different commercially available dianhydrides like benzene‐1,2,4,5‐tetracarboxylic dianhydride (PMDA), benzophenone‐3,3′, 4,4′‐tetracarboxylic dianhydride (BTDA), 4,4′‐(hexafluoro‐isopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 4,4′‐(4,4′‐Isopropylidenediphenoxy)bis(phthalic anhydride) (BPADA) by thermal imidization route. All the poly(ether imide)s showed excellent solubility in several organic solvents such as N‐methylpyrrolidone (NMP), N,N‐dimethylformamide (DMF), N,N‐dimethylacetamide (DMAc), tetrahydrofuran (THF), chloroform (CHCl₃) and dichloromethane (DCM) at room temperature. These light yellow poly (ether imide)s showed very low water absorption (0.19–0.30%) and very good optical transparency. Wide angle X‐ray diffraction measurements revealed that these polymers were amorphous in nature. The polymers exhibited high thermal stability up to 526°C in nitrogen with 5% weight loss, and high glass transition temperature up to 265°C. The polymers exhibited high tensile strength up to 85 MPa, modulus up to 2.5 GPa and elongation at break up to 38%, depending on the exact polymer structure. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Synthesis and characterization of poly(ether ketone ether ketone ketone)/poly(ether ether ketone ketone) copolymers containing naphthalene and pendant cyano groups

2,6‐Bis(β‐naphthoxy)benzonitrile (BNOBN) was synthesized by reaction of β‐naphthol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone (NMP) in the presence of KOH and K₂CO₃. Poly(ether ketone ether ketone ketone)(PEKEKK) /poly(ether ether ketone ketone) (PEEKK) copolymers containing naphthalene and pendant cyano groups were obtained by electrophilic Friedel‐Crafts polycondensation of terephthaloyl chloride (TPC) with varying mole proportions of 4,4′‐diphenoxybenzophenone (DPOBP) and 2,6‐bis(β‐naphthoxy)benzonitrile (BNOBN) using 1,2‐dichloroethane (DCE) as solvent and NMP as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FTIR, DSC, TG, and WAXD. The results indicated that the crystallinity and melting temperature of the polymers decreased with increase in concentration of the BNOBN units in the polymer, the glass transition temperature of the polymers increased with increase in concentration of the BNOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 536°C in N₂ atmosphere. The copolymers have good resistance to acidity, alkali, and organic solvents. Because of the melting temperature (T_m) depression with increase in the BNOBN content in the reaction system, the processability of the resultant coplymers could be effectively improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of silica content in sulfonated poly(arylene ether ether ketone ketone) (SPAEEKK) hybrid membranes on properties for fuel cell application

Sulfonated poly(arylene ether ether ketone ketone) (SPAEEKK) copolymer containing pendant sulfonic acid group (sulfonic acid content (SC) = 0.67) was synthesized from commercially available monomers such as sodium 6,7-dihydroxy-2-naphthalenesulfonate (DHNS), 1,3-bis(4-fluorobenzoyl)-benzene (BFBB), and hexafluorobisphenol A (6F-BPA). SPAEEKK/silica hybrid membranes were prepared using the sol-gel process under acidic conditions. The SPAEEKK/silica hybrid membranes were fabricated with different silica contents and the membranes were modified to achieve improved proton conductivity incorporating P-OH groups (H₃PO₄ treatment).The silica particles within the membranes were used for the purpose of blocking excessive methanol cross-over and for forming a pathway for proton transport due to water absorption onto the hydrophilic SiOH surface. The proton conductivities of H₃PO₄-doped membranes were somewhat higher than the un-doped (H₃PO₄-free) membranes due to increasing hydrophilicity of the membranes. The presence of silica particles within the organic polymer matrix, which decreases the ratio of free water to bound water due to the SiOH on the surface of silica derived from sol-gel reaction, results in hybrid membranes with reduced methanol permeability and improved proton conductivity.