Effect of coagulation conditions on solvent diffusions and the structures and tensile properties of solution spun polyacrylonitrile fibers

Polyacrylonitrile (PAN) fibers were spun by solution spinning. In this work, two coagulation compositions, dimethyl sulfoxide (DMSO)/water and methanol, were used, and coagulation temperatures were varied from ?20 to 0 to 20 °C. The coagulation compositions and temperatures strongly affected the solvent diffusion processes, the structures of as‐spun fibers, and the tensile properties of final drawn fibers. When DMSO/water was used as coagulation bath, non‐solvent (water) diffused into PAN fibers and led to a quick PAN solidification. By comparison, when methanol was used as coagulation bath, no or minimal amount of methanol diffused inward to the fibers. The different solvent diffusion behaviors in DMSO/water and methanol baths led to different structures of as‐spun PAN fibers. It was observed that the tensile properties of final drawn fibers strongly depended on the coagulation conditions. When methanol was used as coagulation bath and the bath temperature was ?20 °C, PAN fibers was found to possess the best tensile properties, a tensile strength of 0.89 GPa and young modulus of 20.4 GPa. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44390.     

Investigating the jet stretch in the wet spinning of PAN fiber

The jet stretch of wet‐spun PAN fiber and its effects on the cross‐section shape and properties of fibers were investigated for the PAN‐DMSO‐H₂O system. Evidently, the spinning parameters, such as dope temperature, bath concentration, and bath temperature, influenced the jet stretch. Also, under uniform conditions, the postdrawing ratio changed as well as that of jet stretch. When coagulation temperature was 35°C simultaneously with bath concentration of 70%, jet stretch impacted obviously the cross‐section shapes of PAN fiber, but had little effect when the temperature was below 10°C or above 70°C. As the jet stretch ratio increased, the crystallinity, crystal size, sonic orientation, and mechanical properties of the as‐spun fiber changed rapidly to a major value for jet stretch ratio of 0.9 where the cross section of as‐spun fiber was circular. With further increasing of jet stretch ratio, the properties changed slightly but the fiber shape was not circular. The results indicated that appropriate jet stretch, under milder formation conditions in wet‐spinning, could result in the higher postdrawing ratio and circular profile of PAN fiber, which were helpful to produce round PAN precursor with minor titer and perfect properties for carbon fiber. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effects of different coagulation conditions on polyacrylonitrile fibers wet spun in a system of dimethylsulphoxide and water

Polyacrylonitrile (PAN) precursors were prepared by the wet spinning way. The effects of the coagulation conditions, such as coagulation temperature, coagulation ratio, and coagulation concentration, are discussed in detail. While keeping the coagulation bath concentration constant, as the coagulation bath temperature increased, the cross section deviated less from a circular form, and the as‐spun fiber diameter decreased. Measurement to the rate of the boundary movement has been calculated depending on the coagulation rate. While keeping the coagulation bath temperature constant, high coagulation bath concentration can cause more coagulant to diffuse into the solution to the polymer precipitated consequently, which led to a faster coagulation rate. The as‐spun fiber from high coagulation concentration was compacted than those from low concentration. The character of the formed structure reflected the system mobility and capability to crystallize. Improvement in fiber density in the as‐spun fiber resulted in improvements in the tensile strength of the as‐spun fiber. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3723–3729, 2007     

Investigation the jet stretch in PAN fiber dry‐jet wet spinning for PAN‐DMSO‐H2O system

The jet stretch of dry‐jet wet spun PAN fiber and its effects on the cross‐section shape of fibers were investigated for a PAN‐DMSO‐H₂O system. Clearly, the spinning parameters, such as dope temperature, bath concentration, bath temperature, and air gap, all influenced the jet stretch. Also, under uniform conditions, the postdrawing ratio as well as that of jet stretch changed. Under given conditions, as the bath temperature was below 30°C or above 45°C, jet stretch had little effect on the cross‐sectional shapes of PAN fiber. Within the temperature of 30–45°C, fiber's cross‐section shapes change obviously from round over an approximate circular shape into to an elliptical or a flat shape. The scope of jet stretch produced PAN fiber with circular cross‐section was bigger than that in wet spinning. These results indicated that appropriate air gap height, under milder formation conditions in dry‐jet wet spinning, could result in higher jet stretch and higher postdrawing ratio. The appropriate jet stretch and postdrawing ratio could result in circular profile of PAN fiber, which were helpful to produce round PAN precursor with finer size and better properties for carbon fiber. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Gel spinning of polyacrylonitrile fibers with medium molecular weight

A new gel‐spinning method was employed to prepare polyacrylonitrile (PAN) fibers from a PAN spinning solution with dimethylsulfoxide and water as a mixed solvent. Aging at 25 °C for 120 min brought the spinning solution to the sol–gel transition and a three‐dimensional gel formed before entering the coagulation bath. The as‐spun fibers from the solution at the sol–gel transition and in the gel state possess a circular cross‐section. Compared with dry‐jet wet‐spun fibers, the gel‐spun fibers have a more compact structure, fewer voids and better mechanical properties after a three‐stage drawing. Moreover, the gel‐spun fibers obtained from the extraction bath have a more homogeneous microstructure and better packed supermolecular structure. The physical properties of the extracted gel‐spun fibers are also better than those of coagulated gel‐spun fibers. Copyright © 2010 Society of Chemical Industry     

Characteristics of wet‐spun and thermally treated poly acrylonitrile fibers

The performance of carbon fibers depends on the quality of the precursor and the conditions of the thermal treatment. In detail, for a PAN precursor fiber the viscosity of a spinning dope and the draw ratio during the spinning process needs to be considered. Through wet spinning, different types of PAN precursor fibers with defined spinning parameters, including solid content, solvent content in a bath, and especially draw ratio resulting in defined cross section diameters, were fabricated and analyzed with tensile tests, density investigations, SEM, TGA‐MS, FTIR, and XRD. The results show that the mechanical properties of the fibers correlate to crystallinity. The cross section diameter is strongly related to the morphology of the fibers after thermal treatment. By extending the postdrawing of PAN fibers high tenacities were obtained at the cost of the cross section shape. In addition, TGA measurements reveal trapped residues of the wet spinning process as well as show several chemical reactions takes place at the same time at different temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43698.     

Structure and properties of partially cyclized polyacrylonitrile‐based carbon fiber—precursor fiber prepared by melt‐spun with ionic liquid as the medium of processing

Carbon fiber has many excellent properties. Currently, the precursor fiber of polyacrylonitrile (PAN)‐based carbon fiber is made from solution by wet or dry spinning process that requires expensive solvents and costly solvent recovery. To solve this problem, we developed a melt‐spun process with ionic liquid as the medium of processing. The melt‐spun precursor fiber exhibited partially cyclized structure. The structure and properties of the melt‐spun PAN precursor fiber were analyzed by combination of scanning electron microscope, Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, thermogravimetry, ultraviolet spectroscopy, flotation technique, sound velocity orientation test, linear density, and tensile strength tests. The results showed that the tensile strength of melt‐spun PAN precursor fiber was fairly high reached up to 7.0 cN/dtex. The reason was the low imperfect morphology and a cyclized structure formed by in situ chemical reaction during melt‐spun process. Due to the existence of partially cyclized structure in the melt‐spun PAN precursor fiber, exothermic process was mitigated and the heat evolved decreased during thermal stabilization stage in comparison with commercial precursor fibers produced by solution‐spun, which could shorten the residence time of thermal stabilization and reduce the cost of final carbon fiber. POLYM. ENG. SCI., 55:2722–2728, 2015. © 2015 Society of Plastics Engineers     

Polyacrylonitrile/acrylamide‐based carbon fibers prepared using a solvent‐free coagulation process: Fiber properties and its structure evolution during stabilization and carbonization

Polyacrylonitrile (PAN)/acrylamide (AM) fibers were fabricated via dry‐jet wet spinning process using a solvent‐free coagulation bath. The effects of AM loading as comonomer on the mechanical and thermal properties of PAN‐based carbon fiber have been studied. The thermal stability and mechanical stability of the fibers were characterized using differential scanning calorimetry (DSC) and tensile testing. Fibers fabricated from PAN with 5 wt% AM had the highest Young Modulus at 5.54 GPa. It also showed better exothermic trend process with broader exothermic peak and lower initiation stabilization temperature compared with homopolymer PAN. The elemental composition and chemical structure evolution of the fibers during the heat treatment processes were evaluated by elemental analyzer and Fourier Transform Infrared Spectroscopy. Crystal structure evolution of the fibers during the heat treatment process was elucidated by X‐ray diffraction (XRD) analysis. The elemental analyzer, XRD and FTIR results revealed that pyrolysis process used had successfully transformed PAN/AM fibers produced from solvent free coagulation bath into carbon fibers that were comparable with the conventional coagulation bath. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Direct drawing of gel fibers enabled by twist‐gel spinning process

A new twist‐gel spinning process for ultrahigh molecular weight polyethylene fibers is demonstrated which significantly increases the extraction rate of nonvolatile spin solvent while simultaneously reducing the consumption of extraction solvent by more than 75%. Applying twist to the gel fiber enables it to be directly hot‐drawn, allowing conventional solvent extraction to proceed significantly faster. While solvent extraction effectiveness is largely enhanced, the new process does not show reduced fiber properties. The tensile strength, Young's modulus, surface morphology, and geometry are relatively unaffected when compared to fibers produced using the conventional gel‐spinning process. The new twist‐gel spinning process is expected to improve the processing efficiency of gel‐spun high‐strength fibers, promoting broad expansion of these high performance fibers into applications that were previously prohibitive due to extremely slow production. POLYM. ENG. SCI., 55:1389–1395, 2015. © 2015 Society of Plastics Engineers     

Studies on high‐speed melt spinning of noncircular cross‐ section fibers. I. Structural analysis of as‐spun fibers

Flat fibers and hollow fibers were prepared through the high‐speed melt spinning of poly(ethylene terephthalate) (PET), and the structures of these fibers were compared with those of circular fibers. The cross‐sectional shape of each fiber changed to a dull shape in comparison with that of the respective spinning nozzle. The change in the cross‐sectional shape was slightly suppressed with an increase in the take‐up velocity. There was a significant development of structural variation in the cross section of flat fibers in that the molecular orientation and crystallization were enhanced at the edge. Despite the difference in the cross‐sectional shape, the structural development of flat, hollow, and circular fibers with increasing take‐up velocity showed almost similar behavior. Considering that the tensile stress at the solidification point of the spin line is known to govern the structure development of high‐speed spun PET fibers, it was speculated that the effects of the enhancement of cooling and air friction on the tensile stress at the solidification point cancel each other. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1575–1581, 2001     

The index of dry‐jet wet spinning for polyacrylonitrile precursor fibers

A new spinning index for a PAN precursor fiber is proposed that includes the viscosity of a spinning dope, the thermodynamic affinity, and the draw ratio during the spinning process. Through dry‐jet wet spinning, six types of PAN precursor fibers with different spinning parameters, including solid content, solvent content in a bath, and draw ratio, were fabricated and analyzed with tensile tests, SEM, and XRD. The results show that the spinning index can reflect the mechanical properties of the fibers but is less indicative of crystallinity. Hence, the current spinning index is recommended for use as an indicator for the mechanical properties of PAN precursor fibers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41265.     

Gel‐spun polyacrylonitrile fiber from pregelled spinning solution

Polyacrylonitrile (PAN) fibers have been gel spun from pregelled PAN spinning solution. The pregelled solution had network structure with elevated spinnability, the as‐spun fiber from which had more circular cross‐section and reduced skin‐core difference. Drawing was more effective in inducing the segmental orientation and crystallization in gel‐spun fiber than in dry–wet spun fiber. The mechanical properties of the gel‐spun fiber were better than those of the dry–wet spun fiber after multi‐stage drawing. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Comparison of tensile,thermal, and thermo‐mechanical properties of polyester filaments having different cross‐sectional shape

One of the most important morphological features of fibers is their cross‐sectional shape. Nowadays, the circular fiber cross‐section is the most common shape of melt‐spun man‐made fibers. Other shapes are beginning to emerge for a variety of reasons such as performance, comfort, pilling propensity, bulkiness, tactility, processing etc. The filaments' cross‐section can be easily varied by changing the spinneret hole shape. Synthetic fibers that are predominantly spun by the melt spinning method with spinnerets having the noncircular hole geometry are called profiled or noncircular fibers. Modifications of the fiber cross‐section allow designing surface properties in yarn and fabric. However, the effect of profiled fibers on yarn properties has not been well documented yet. In this article, the influence of different filament cross‐section geometry on fiber properties was studied. PET (polyethylene terephthalate) filament yarns having two different cross‐sectional shaped filaments, circular and cruciform, were manufactured by melt spinning. Differences in tensile properties of filament yarn and as well as of individual filament depending on the cross‐sectional type were studied and revealed. More over, thermal and thermomechanical properties of filament yarn of both the cross‐sections were studied and revealed by DSC and TMA method, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and properties of polyamide 6 fibers prepared by the gel spinning method

Polyamide 6 (PA6) fibers were prepared by CaCl₂ complexation and the gel spinning technique. PA6 was partially complexed with CaCl₂ for the purpose of suppressing interchain amide group hydrogen bonding. The fibers were characterized with scanning electron microscopy, X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR) spectroscopy. In the gel spinning process, a mixed tetrachloroethane and chloroform solution was chosen as the coagulation bath after a comparison of different types of solutions. From our investigation of the morphology, structure, and mechanical properties of gel‐spun and hot‐drawn fibers, it was indicated that the modulus and tensile strength increased with increasing draw ratio, the orientation of the fibers was improved, and the cross section of the PA6 gel fibers became more smooth and tight. The results from the XRD, DSC, and FTIR tests indicated that calcium metal cations complexed with the carbonyl oxygen atoms of PA6. The maximum modulus and tensile strength values obtained in this study were 28.8 GPa and 413 MPa, respectively, at a draw ratio of 8. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Impact of the wet spinning parameters on the alpaca-based polyacrylonitrile composite fibers: Morphology and enhanced mechanical properties study

The study examined the effect of different wet spinning parameters (e.g., total solid content, coagulation bath concentration, drawing, and stretching) on the morphology and mechanical properties of the wet spun alpaca/polyacrylonitrile (PAN) composite fibers. The alpaca/PAN composite fibers were wet spun using 10, 20, and 30% of alpaca particles along with the PAN polymer. The shear-thinning or non-Newtonian flow behavior was observed among the dope solutions with different solid content. The cross-sectional fiber morphology showed the bean-shaped characteristic for the control PAN fibers, whereas the alpaca/PAN composite fibers exhibited almost circular shape. “Cavity healing” was observed, where noticeable voids and porous areas were demolished in the cross section of the composite fibers, by changing the total solid content and coagulation bath concentration. Although the control PAN fibers exhibited the highest tenacity with lower fiber diameter, the alpaca/PAN composite fibers showed a gradual deterioration in tenacity while adding alpaca particles into the PAN polymeric matrix. Nevertheless, due to the increment in the total solid content, higher draw ratio, and stretching of the fibers, the tenacity, molecular orientation, and the crystallinity of the composite fibers were increased.     

Morphology of polyimide fibers derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline

As one member of high performance fibers, aromatic polyimide fibers possess many advantages, such as high strength, high modulus, high and low temperature resistance, and radiation resistance. However, the preparation of the high performance fibers is so difficult that the commercial fibers have not been produced except P84 with good flame retardancy. In this report, a polyimide was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydianiline (ODA) and the fibers were prepared from its solution by a dry‐jet wet‐spinning process. The formation of the as‐spun fibers in different coagulation bath composition was discussed. Scanning electron microscope (SEM) was employed to study the morphology of the as‐spun fibers. As a result, the remnant solvent existed in the as‐spun fibers generated from coagulation bath of alcohol and water. There were many fibrils and microvoids with the dimension of tens of nanometers in the fibers. One could observe the obvious fibrillation and the drawn fibers. The measurement for the mechanical properties of the fibers with a drawing ratio of 5.5 indicated that tensile strength and initial modulus were 2.4 and 114 GPa, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 669–675, 2004     

Effects of water on drawability,structure, and mechanical properties of poly(vinyl alcohol) melt‐spun fibers

Poly(vinyl alcohol) (PVA) melt‐spun fibers with circular cross‐section and uniform structure, which could support high stretching, were prepared by using water as plasticizer. The effects of water content on drawability, crystallization structure, and mechanical properties of the fibers were studied. The results showed that the maximum draw ratio of PVA fibers decreased with the increase of water content due to the intensive evaporation of excessive water in PVA fibers at high drawing temperature. Hot drying could remove partially the water content in PVA as‐spun fibers, thus reducing the defects caused by the rapid evaporation of water and enhancing the drawability of PVA fibers at high drawing temperature. The decreased water content also improved the orientation and crystallization structure of PVA, thus producing a corresponding enhancement in the mechanical properties of the fibers. When PVA as‐spun fibers with 5 wt % water were drawn at 180 °C, the maximum draw ratio of 11 was obtained and the corresponding tensile strength and modulus reached ～0.9 GPa and 24 GPa, respectively. Further drawing these fibers at 215 °C and thermal treating them at 220 °C for 1.5 min, drawing ratio of 16 times, tensile strength of 1.9 GPa, and modulus of 39.5 GPa were achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45436.     

Correlation between inhomogeneity in polyacrylonitrile spinning dopes and carbon fiber tensile strength

The nano‐scale and micro‐scale inhomogeneity of polyacrylonitrile (PAN) spinning dopes obtained from dynamic light scattering (DLS) experiment is correlated with the tensile strength of the resulting carbon fiber. The nanoscale inhomogeneity was estimated by calculating the diffusion coefficients from the slow relaxation mode of polymer solutions in DLS. The nanoscale inhomogeneity in the spinning dopes was found to be in the range of 1–45 nm. We also demonstrate mean of the count rate (MCR) obtained from DLS of PAN solution as a tool to detect the microscale inhomogeneity in the spinning dope for the first time. The MCR of spinning dopes varied from ~10.0 to 77.5 kcps (kilo‐counts per second). The tensile strength of carbon fibers from the precursor fiber spun from the spinning dopes in this study varied from 3 to 5.2 GPa. Correlation studies show that the microscale inhomogeneity in the spinning dope was a major contributor to the decrease in the tensile strength of carbon fibers in the range of 3–4.5 GPa. Contaminants causing microscale inhomogeneity in PAN powder were removed by using micelles, reverse micelles and frothing. The surfactant treated PAN polymer was characterized using a fourier transform infrared spectroscope, differential scanning calorimeter, and thermal gravimetic analyzer to demonstrate complete removal of surfactants. POLYM. ENG. SCI., 59:478–482, 2019. © 2018 Society of Plastics Engineers     

Carbon fibers derived from wet‐spinning of equi‐component lignin/polyacrylonitrile blends

Equi‐component blends of polyacrylonitrile (PAN) and lignin, i.e., with a lignin content as large as 50 wt %, were successfully used as precursors to produce carbon fibers. Rheological measurements demonstrated that increasing lignin content in spinning solution reduced shear viscosity and normal stress, indicating a decrease of viscoelastic behavior. This was confirmed by Fourier transform infrared results that show no discernable chemical reaction or crosslinking between PAN and lignin in the solution. However, the resulting carbon fibers display a large I_D/I_G ratio (by Raman spectroscopy) indicating a larger disordered as compared to that from pure PAN. The macro‐voids in the lignin/PAN blend fibers typically generated during wet‐spinning were eliminated by adding lignin in the coagulant bath to counter‐balance the out‐diffusion of lignin. Carbon fibers resulting from lignin/PAN blends with 50 wt % lignin content displayed a tensile strength and modulus of 1.2 ± 0.1 and 130 ± 3 GPa, respectively, establishing that the equi‐component wet‐spun L/P‐based carbon fibers possessed tensile strength and modulus higher than 1 and 100 GPa. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45903.     

Wet-spinning assembly of continuous and macroscopic graphene oxide/polyacrylonitrile reinforced composite fibers with enhanced mechanical properties and thermal stability

Polyacrylonitrile (PAN) composite microfibers with different contents of graphene oxide (GO) were fabricated via wet-spinning route in this work. Based on nonsolvent-induced phase separation theory, N,N-dimethyl formamide/water mixture system was employed as coagulation bath, nonsolvent (water) diffused into PAN spinning solution and led to a quick PAN fiber solidification. Nematic liquid crystal state of GO dispersions and GO/PAN spinning solutions were determined via polarized optical microscopy images, and the morphology and structure of the composite fibers were characterized via scanning electron microscope, Transmission electron microscopy, Fourier transform infrared spectra, and X-ray diffraction. 1 wt % GO/PAN composite fibers exhibited outstanding mechanical properties, 40% enhancement in tensile strength and 34% enhancement in Young's modulus compared with pure PAN fiber. The results of dynamic mechanical analysis indicated that the composite fiber with 1 wt % GO performed the best thermal mechanical property with 5.5 GPa and 0.139 in storage modulus and loss tangent, respectively. In addition, thermogravimetric analysis showed that thermal stability of the composite fibers enhanced with the increasing GO contents. GO/PAN composite fibers can be as the candidate of carbon fiber precursor, high performance fibers, and textiles applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46950.