Methanol permeability and proton conductivity of polybenzimidazole and sulfonated polybenzimidazole

The preparation of sulfonated polybenzimidazole (sPBI) by the grafting of (4‐bromomethyl) benzenesulfonate onto polybenzimidazole (PBI) has been investigated. The methanol permeability and proton conductivity of PBI and sPBI have been studied, and the effects of methanol concentration and temperature on the methanol permeability of PBI and sPBI membranes are discussed. The results showed that the PBI membrane is a good methanol barrier. Methanol permeability in this membrane decreases with increasing methanol concentration and increases with increasing temperature. The temperature‐dependence of methanol permeability of PBI and sPBI membranes is of the ‘Arrhenius type’. Methanol permeation of sPBI is less sensitive to temperature than that of PBI. However, sPBI is a poorer methanol barrier when compared to PBI. Methanol permeability in sPBI membranes increases with increasing methanol concentration and temperature. The proton conductivity of sPBI is 4.69 × 10^?4 S cm^?1 at room temperature in the hydrated state. The DC conductivity of sPBI–H₃PO₄ increases with increasing temperature. Proton transport in sPBI–H₃PO₄ is less sensitive to temperature than that in PBI–H₃PO₄. Copyright © 2004 Society of Chemical Industry     

Fabrication and characterization of sulfonated polybenzimidazole/sulfonated imidized graphene oxide hybrid membranes for high temperature proton exchange membrane fuel cells

The sulfonated polybenzimidazole (sPBI)/sulfonated imidized graphene oxide (SIGO) was evaluated to be a potential candidate for high temperature proton exchange membranes fuel cells (HT-PEMFCs). Multifunctionalized covalently bonded SIGO is incorporated in sPBI matrix to resolve the drawbacks such as low proton conductivity, poor water uptake, and ion-exchange capacity (IEC) of sPBI polymer, synthesized by direct polycondensation in phosphoric acid for the application of proton exchange membranes. Strong hydrogen bonding among multifunctional groups established a neighborhood of interconnected hydrophobic graphene sheets and organic polymer chains. It provides hydrophobic–hydrophilic phase separation and facile proton hopping architecture. The optimized sPBI/SIGO (15 wt %) revealed 2.45 meq g⁻¹ IEC; 5.81 mS cm⁻¹ proton conductivity [120 °C and 10% relative humidity (RH)] and 2.45% bound water content. The maximum power density of the sPBI/SIGO-15 membrane was 0.40 W cm⁻² at 160 °C (5% RH) and ambient pressure with stoichiometric feed of H₂/air. This recommends that sPBI/SIGO composite membranes are compatible candidate for HT-PEMFCs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47892.     

New organic–inorganic hybrid membranes based on sulfonated polyimide/aminopropyltriethoxysilane doping with sulfonated mesoporous silica for direct methanol fuel cells

A series of novel composite methanol‐blocking polymer electrolyte membranes based on sulfonated polyimide (SPI) and aminopropyltriethoxysilane (APTES) doping with sulfonated mesoporous silica (S‐mSiO₂) were prepared by the casting procedure. The microstructure and properties of the resulting hybrid membranes were extensively characterized. The crosslinking networks of amino silica phase together with sulfonated mesoporous silica improved the thermal stability of the hybrid membranes to a certain extent in the second decomposition temperature (250–400°C). The composite membranes doping with sulfonated mesoporous silica (SPI/APTES/S‐mSiO₂) displayed superior comprehensive performance to the SPI and SPI/APTES membranes, in which the homogeneously embedded S‐mSiO₂ provided new pathways for proton conduction, rendered more tortuous pathways as well as greater resistance for methanol crossover. The hybrid membrane with 3 wt % S‐mSiO₂ into SPI/APTES‐4 (SPI/A‐4) exhibited the methanol permeability of 4.68 × 10^?6 cm² s^?1at 25°C and proton conductivity of 0.184 S cm^?1 at 80°C and 100%RH, while SPI/A‐4 membrane had the methanol permeability of 5.16 × 10^?6 cm² s^?1 at 25°C and proton conductivity of 0.172 S cm^?1 at 80°C and 100%RH and Nafion 117 exhibited the values of 8.80 × 10^?6 cm² s^?1 and 0.176 S cm^?1 in the same test conditions, respectively. The hybrid membranes were stable up to about 80°C and demonstrated a higher ratio of proton conductivity to methanol permeability than that of Nafion117. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Sulfonated graphene oxide‐doped proton conductive membranes based on polymer blends of highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole

Simultaneously improving the proton conductivity and mechanical properties of a polymer electrolyte membrane is a considerable challenge in commercializing proton exchange membrane fuel cells. In response, we prepared a new series of miscible polymer blends and thus the corresponding crosslinked membranes based on highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole. The blended membranes showed more compact structures, due to the acid‐base interactions between the two constituents, and improved mechanical and morphological properties. Further efforts by doping sulfonated graphene oxide (s‐GO) forming composite membranes led to not only significantly elevated proton conductivity and electrochemical performance, but also better mechanical properties. Notably, the composite membrane with the filler content of 15 wt % exhibited a proton conductivity of 0.217 S cm^?1 at 80 °C, and its maximum power density tested by the H₂/air single PEMFC cell at room temperature reached 171 mW cm^?2, almost two and half folds compared with that of the native membrane. As a result, these polymeric membranes provided new options as proton exchange membranes for fuel‐cell applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46547.     

Preparation and proton conductivity of phosphoric acid‐doped blend membranes composed of sulfonated block copolyimides and polybenzimidazole

A series of phosphoric acid (PA)‐doped blend membranes composed of block or random sulfonated polyimides (SPIs) and polybenzimidazole (PBI) were prepared with similar PA contents to investigate the influence of chemical structures of SPIs on proton conductivity. The proton conductivity of a PA‐doped blend membrane containing block‐type SPI, PA‐bSPI(80/20)/oPBI, was higher than that of the corresponding pristine block‐type SPI, PA‐SPI/PBI containing random‐type SPI and Nafion membranes over a wide temperature range, and reached 0.37 S cm^?1 at 90 °C and 98% relative humidity. The PA‐bSPI(80/20)/oPBI membrane also showed distinct proton conductivity even at low humidity due to a new proton transport pathway among PA and sulfonic acid groups. Also, the novel PA‐doped blend membrane showed higher proton conductivity than Nafion at both above 100 °C and below 0 °C under low relative humidity conditions. © 2013 Society of Chemical Industry     

Preparation and characterization of poly(vinylidene fluoride)/sulfonated poly(phthalazinone ether sulfone ketone) blends for proton exchange membrane

Poly(vinylidene fluoride)/sulfonated poly(phthalazinone ether sulfone ketone) (PVdF/SPPESK) blend membranes are successfully prepared by solution blending method for novel proton exchange membrane (PEM). PVdF crystallinity, FTIR‐ATR spectroscopy, thermal stability, morphology, water uptake, dimension stability, and proton conductivity are investigated on PVdF/SPPESK blends with different PVdF contents. XRD and DSC analysis reveal that the PVdF crystallinity in the blends depends on PVdF content. The FTIR‐ATR spectra indicate that SPPESK remains proton‐conducting function in the blends due to the intactness of ? SO₃H group. Thermal analysis results show a very high thermal stability (T_d1 = 246–261°C) of the blends. PVdF crystallinity and morphology study demonstrate that with lower PVdF content, PVdF are very compatible with SPPESK. Also, with lower PVdF content, PVdF/SPPESK blends possess high water uptake, e.g., P/S 10/90 and P/S 15/85 have water uptake of 135 and 99% at 95°C, respectively. The blend membranes also have good dimension stability because the swelling ratios are at a fairly low level (e.g., 8–22%, 80°C). PVdF/SPPESK blends with low PVdF content exhibit very high proton conductivity, e.g., at 80°C, P/S 15/85 and P/S 10/90 reach 2.6 × 10^?2 and 3.6 × 10^?2 S cm^?1, respectively, which are close to or even higher than that (3.4 × 10^?2 S cm^?1) of Nafion115 under the same test condition. All above properties indicate that the PVdF/SPPESK blend membranes (particularly, with 10–20% of PVdF content) are very promising for use in PEM field. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Regulation of micromorphology and proton conductivity of sulfonated polyimide/crosslinked PNIPAm semi‐interpenetrating networks by hydrogen bonding

A series of novel sulfonated polyimide (SPI)/crosslinked poly(N‐isopropylacrylamide) (cPNIPAm) semi‐interpenetrating polymer networks (semi‐IPNs) were synthesized as the proton exchange membranes for direct methanol fuel cells via in situ polymerization. The micromorphology and properties of the semi‐IPN membranes were characterized. The results indicated that the hydrogen bonds between cPNIPAm and SPI in the semi‐IPN structure were a crucial factor for regulating the micromorphology, proton conductivity and other properties of the semi‐IPN membranes. A more uniform sulfonic ionic cluster distribution was observed in the membrane of SPI‐20‐cPNIPAm with equimolar ratio of sulfonic acid groups and amido bonds, which could provide effective proton transport channels. The SPI‐20‐cPNIPAm exhibited a maximum proton conductivity of 0.331 S cm^?1 at 80 ^oC (relative humidity 100%), an optimal selectivity of 8.01 × 10⁵ S s cm^?3 and an improved fuel cell performance of 72 mW cm^?2 compared with both pristine SPI and other semi‐IPN membranes. The SPI‐20‐cPNIPAm semi‐IPN membranes also retained good mechanical properties and thermal stabilities on the whole. © 2014 Society of Chemical Industry     

Polymer electrolyte membranes based on blends of sulfonated polysulfone and PEO‐grafted polyethersulfone for low temperature water electrolysis

Polymer electrolyte membranes based on blends consisting of polyethylene oxide (PEO) grafted polyether sulfone (PES‐g‐PEO) and sulfonated polysulfone (SPSF(Na)) are prepared and their electrochemical and mechanical properties are investigated with respect to water electrolysis operation. The prepared blends are amorphous; they exhibit high glass transition temperatures and high thermal stability, thus ensuring the dimensional stability under electrolysis cell operation. Because of the presence of the water soluble constituent PES‐g‐PEO, the prepared blend membranes show very high water uptakes, reaching up to 370 wt %. Membrane electrode assemblies are fabricated and evaluated in single cells demonstrating that proton conductivity depends on the PEO‐g‐PES content as well as the PEO molecular weight. Namely, the increased concentration of PES‐g‐PEO leads to increased number of charge carriers, thus result in enhanced ionic conductivity. The use of longer PEO units (MW 5000), due to their improved chain mobility, facilitates the fast proton conduction as well. The maximum proton conductivity value is achieved (1.4 × 10^?2 S cm^?1, 80°C) for the blend with the higher PEO‐g‐PES content (20 wt %) and the higher PEO molecular weight (5000). Under electrolysis cell operation, the above‐mentioned membrane with the lower ohmic resistance shows the best performance, although it is still poor mainly due to the use of Pt as anode. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39922.     

Chelate membrane from poly(vinyl alcohol)/poly(n-salicylidene allyl amine) blend. II. Effect of co(II) content on oxygen/nitrogen separation

Facilitated transport of oxygen was performed through chelate membranes containing cobalt with selective oxygen binding ability as a fixed oxygen carrier. Chelate membranes were obtained from Schiff base membranes after treating a poly(allyl amine) (PAAm) and poly(vinyl alcohol) (PVA) blend with salicylaldehyde. It is confirmed that the O? O stretching peak through a frequency change in FTIR could be seen at 1150 cm^?1 between cobalt in the membrane and incoming oxygen. The permeability of oxygen through Schiff base membranes was 2.01?2.98 × 10^?13 [cm³ (STP) cm²/cm s cmHg] and oxygen permselectivity was in the range of 1.83?3.27. For chelate membranes, both the permeability of oxygen and oxygen selectivity increased to 2.15?2.82 × 10^?12 [cm³ (STP) cm²/cm s cmHg] and around 8, respectively. Permselectivity of chelate increased as a result of facilitation of O₂ and inhibition of N₂ transport. Detailed results and the mechanism of facilitation of oxygen are discussed on the basis of molecular interactions. © 1995 John Wiley & Sons, Inc.     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

In situ sol–gel route to novel sulfonated polyimide?SiO2 hybrid proton‐exchange membranes for direct methanol fuel cells

Polyimides (PIs) as high‐performance organic matrices are used in the preparation of PI composites because of their excellent mechanical, thermal and dielectric properties. The sol–gel method is a promising technique for preparing these PI composites due to the mild reaction conditions and the process being controllable. Although sulfonated polyimide (SPI) proton‐exchange membranes have attracted much attention recently, studies on preparing SPI‐based hybrid proton‐exchange membranes for fuel cells have been rare. A series of SPI? SiO₂ hybrid proton‐exchange membranes were prepared from amino‐terminated SPI pre‐polymers, 3‐glycidoxypropyltrimethoxysilane (KH‐560) and tetraethylorthosilicate through a co‐hydrolysis and condensation process using an in situ sol–gel method. The reactive silane KH‐560 was used to react with amino‐terminated SPI to form silane‐capped SPI in order to improve the compatibility between the polymer matrix and the inorganic SiO₂ phase. The microstructure and mechanical, thermal and proton conduction properties were studied in detail. The hybrid membranes were highly uniform without phase separation up to 30 wt% SiO₂. The storage modulus and tensile strength of the hybrid membranes increased with increasing SiO₂ content. The introduction of SiO₂ improved the methanol resistance while retaining good proton conductivity. The hybrid membrane with 30 wt% SiO₂ exhibited a proton conductivity of 10.57 mS cm^?1 at 80 °C and methanol permeability of 2.3 × 10^?6 cm² s^?1 possibly because the crosslinking structure and SiO₂ phases formed in the hybrids could retain water and were helpful to proton transport. Copyright © 2010 Society of Chemical Industry     

Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

SPES‐SiO2 hybrid proton exchange membranes from in situ sol–gel process of negatively charged alkoxysilane

One type of negatively charged alkoxysilane, that is, sulfonated 3‐(mercaptopropyl)trimethoxysilane (SMPTS), has been developed from 3‐(mercaptopropyl)trimethoxysilane (MPTS) and hydrogen peroxide. SMPTS is used to modify sulfonated poly(ether sulfone) (SPES) through in situ sol–gel process. The membranes with proper SMPTS dosage show enhanced ion exchange capacity (IEC), hydrophilicity, mechanical strength, chemical stability, and proton conductivity, which prove that SMPTS is an effective modifier for preparing proton‐exchange hybrid membranes. With MPTS of 5–20%, the hybrid membranes exhibit IEC 1.34–1.50 mmol g^?1, thermal stability 264–316°C, and proton conductivity 0.0015–0.0102 S cm^?1 and thus recommended for potential application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Vinyl‐addition type norbornene copolymer containing sulfonated biphenyl pendant groups for proton exchange membranes

The vinyl addition type copolymer poly(butoxymethylene norbornene‐co‐biphenyl oxyhexamethyleneoxymethylene norbornene) (P(BN/BphN)) was synthesized by using bis‐(β‐ketonaphthylimino)nickel(II)/B(C₆F₅)₃ catalytic system. P(BN/BphN) was sulfonated to give sulfonated P(BN/BphN) (SP(BN/BphN)) with concentrated sulfuric acid (98%) as sulfonating agent in a component solvent. The ion exchange capacity (IEC), degree of sulfonation (DS), water uptake, and methanol permeability of the SP(BN/BphN)s were increased with the sulfonated time. The methanol permeability of the SP(BN/BphN) membranes was in the range of 1.8 × 10^?7 to 7.5 × 10^?7 cm²/s, which were lower than the value 1.3 × 10^?6 cm²/s of Nafion®115. The proton conductivity of SP(BN/BphN) membranes increased with the increase of IEC values, temperature, and water uptake. Water uptake of the SP(BN/BphN) membranes was lower than that of Nafion® 115 and leads to low proton conduction. Microscopic phase separation occurred in SP(BN/BphN) membrane and domains containing sulfonic acid groups were investigated by SEM and TEM. SP(BN/BphN) membranes had good mechanical properties, high thermal stability, and excellent oxidative stability. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Vinyl‐addition type norbornene copolymers containing flexible spacers and sulfonated pendant groups for proton exchange membranes

Novel sulfonated poly(2‐butoxymethylenenorbornene‐co‐2‐(6‐phenoxy‐hexyloxymethylene)‐5‐norbornene [sP(BN/PhHN)] were prepared successfully through vinyl‐addition type polymerization and then sulfonated with concentrated sulfuric acid (98%) as sulfonating agent in a component solvent. The sP(BN/PhHN)‐40 with the maximal degree of sulfonation of 40% can be obtained by controlling the sulfonating reaction time from 8 to 20 h, and a proton conductivity of 3.35 × 10^?3 S/cm was achieved at 70°C. The methanol permeabilities of these membranes were in the range from 0.26 to 6.58 × 10^?7 cm²/s, which were remarkably lower than Nafion (2.36 × 10^?6 cm²/s). TEM analysis revealed that these side‐chain type membranes have a microphase separated structure composed of hydrophilic side‐chain domains and hydrophobic polynorbornene main chain domains. Sulfonated polynorbornene containing soft spacers displayed better properties, such as lower water uptake, high thermal properties, mechanical properties, and low methanol permeability. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Novel polymer electrolyte membranes based on semi‐interpenetrating blends of poly(vinyl alcohol) and sulfonated poly(ether ether ketone)

In this work, the properties of novel ionic polymer blends of crosslinked and sulfonated poly(vinyl alcohol) (PVA) and sulfonated poly(ether ether ketone) (SPEEK) are investigated. Crosslinking and sulfonation of PVA were carried out using sulfosuccinic acid (SSA) in the presence of dispersed SPEEK to obtain semi‐interpenetrating network blends. PVA–SSA/SPEEK blend membranes of different compositions were studied for their ion‐exchange capacity, proton conductivity, water uptake, and thermal and mechanical properties. The hydrated blend membranes show good proton conductivities in the range of 10^?3 to 10^?2 S/cm. When compared with pure component membranes, the PVA–SSA/SPEEK blend membranes also exhibit improvement in tensile strength, tensile modulus, and delay in the onset of thermal and chemical degradation. Semi‐interpenetrating nature of the blends is established from morphology and dynamic mechanical analysis. Morphology of the membranes was studied using scanning electron microscopy after selective chemical treatment. The dynamic mechanical properties of the membranes are examined to understand the miscibility characteristics of the blends. The relative proportions of PVA and SPEEK and the degree of crosslinking of PVA–SSA are important factors in determining the optimum properties for the blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Sulfonated poly(ether ether ketone)/epoxy/phenol novolac blend proton‐exchange membranes with low methanol permeability

A crosslinked epoxy [4,4′‐diglycidyl‐(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)], cured by phenol novolac (PN), was introduced into a sulfonated poly(ether ether ketone) (SPEEK) membrane (ion‐exchange capacity = 2.0 mequiv/g) with a casting‐solution, evaporation, and heating crosslinking method to improve the mechanical properties, dimensional stability, water retention, and methanol resistance. By Fourier transform infrared analysis, the interactions between the sulfonic acid groups and hydroxyl groups in the blend membranes were confirmed. The microstructure and morphology of the blend membranes were investigated with atomic force microscopy. As expected, the blend membranes showed excellent mechanical properties, good thermal properties (thermal stability above 200°C), lower swelling ratios (1.4% at 25°C and 7.0% at 80°C), higher water retention (water diffusion coefficient = 9.8 × 10^?6 cm²/s), and a lower methanol permeability coefficient (3.6 × 10^?8 cm²/s) than the pristine SPEEK membrane. Although the proton conductivity of the blend membranes decreased, a higher selectivity (ratio of the proton conductivity to the methanol permeability) was obtained than that of the pristine SPEEK membrane. The results showed that the SPEEK/TMBP/PN blend membranes could have potential use as proton‐exchange membranes in direct methanol fuel cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phthalonitrile end-capped sulfonated polyarylene ether nitriles for low-swelling proton exchange membranes

A series of phthalonitrile end-capped sulfonated polyarylene ether nitriles are synthesized via K₂CO₃ mediated nucleophilic aromatic substitution reaction at various molar ratios. The as-prepared polymer structures are confirmed by ¹H NMR and FTIR spectroscopy. The properties of membranes cast from the corresponding polymers are investigated with respect to their structures. The membranes exhibit good thermal and mechanical properties, low methanol permeability (0.01?×?10^?6–0.58?×?10^?6 cm²·s^?1 at 20 °C), and high proton conductivity (0.021–0.088 S·cm^?1 at 20 °C). The introduction of phthalonitrile is proved to increase intermolecular interaction, mainly contributing to the reduction in water uptake, swelling ratio, and methanol permeability. More importantly, its introduction does not decrease the proton conductivity, but there is a slight increase. Furthermore, the selectivity of SPEN-CN-50 can reach 4.11?×?10⁵ S·s·cm^?3, which is about nine times higher than that of Nafion 117. All the data show that the as-prepared membranes may be potential proton exchange membrane for DMFCs applications.