Structure and Performance of Poly(vinylidene chloride‐co‐vinyl chloride) Porous Membranes with Different Additives

Poly(vinylidene chloride‐co‐vinyl chloride) (P(VDC‐co‐VC) membranes were prepared by non‐solvent‐induced phase separation and adjusted by adding water‐soluble polyethylene glycol (PEG) and water‐insoluble silicon dioxide (SiO₂) hydrophilic nanoparticles. The structure of pores and antifouling performance were investigated to illustrate the effect of these nanoparticles. The cross section of the P(VDC‐co‐VC) membrane exhibited more macropores and the typical finger‐like pores turned into more vertically interconnected ones with increasing PEG content, while the number and size of finger‐like pores became less with increasing SiO₂ content. Considering the filtration and antifouling experiments, the presence of hydrophilic PEG and SiO2 nanoparticles in the P(VDC‐co‐VC) polymer matrix improved the membrane performance in terms of high flux, high BSA rejection ratio, and fouling resistance.     

Amphiphilic poly(acrylonitrile‐co‐acrylic acid)/silver nanocomposite additives for the preparation of antibiofouling membranes with improved properties

This work focuses the preparation of polymer‐silver nanocomposite (Ag‐Nc) dense free standing films and nonwoven fabric supported porous ultrafiltration membranes with improved membrane performance and long‐term antibiofouling properties. New polyacrylonitrle‐based Ag‐Ncs, poly(acrylonitrle‐co‐acrylic acid)‐silver (PAN‐co‐PAA‐Ag) containing 35 wt% of PAA and 0.35–0.65 wt% of Ag‐nanoparticles (Nps) were synthesized and used as additives for the fabrication of PAN‐based (PAN/PAN‐co‐PAA‐Ag) Ag‐Nc porous membranes and dense‐free standing films. The Ag‐Nps were homogeneously dispersed into the PAN‐co‐PAA random copolymer matrix. The prepared membranes (PAN/PAN‐co‐PAA‐Ag) showed combination of properties such as excellent antimicrobial activity towards both Gram Negative and Gram Positive bacteria (prevent biofilm formation), improved protein antifouling properties, and enhanced water flux when compared to neat PAN‐based membrane. The antimicrobial properties, hydrophilicity, and the water flux of various membranes follow the following order for the membranes PAN < PAN/PAN‐co‐PAA < PAN/PAN‐co‐PAA‐Ag. Extraneous addition of small amount of polyethylene glycol (PEG) during preparation of additive i.e. [PEG + PAN‐co‐PAA]‐Ag further improved the protein antifouling properties of the PAN‐based membranes (PAN/[PEG+PAN‐co‐PAA‐Ag]). The dispersed Ag‐Nps were stable on the surface of phase inverted membranes for long period of time and PAN/PAN‐co‐PAA‐Ag membranes are therefore suitable for long‐term water treatment under bacterial environment. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Effective incorporation of TiO2 nanoparticles into polyamide thin‐film composite membranes

The effectiveness of TiO₂ nanoparticles in improving the performance of polyamide (PA) thin‐film composite (TFC) membranes has been investigated. PA TFC membranes were prepared by interfacial polymerization with m‐phenylenediamine (MPD) and 1,3,5‐benzene tricarbonyl trichloride (TMC) where TiO₂ particles were added during and after interfacial polymerization. To distribute the TiO₂ nanoparticles uniformly in the PA films, colloidally stable TiO₂ sols were synthesized and added to the aqueous MPD solution rather than to an organic TMC solution. Through the use of different incorporation methods, TiO₂ particles were located on the top surface, in PA film layer, and in both positions. In the case of dense PA layers, the hydrophilicity of the membranes was significantly improved due to the presence of TiO₂ particles, resulting in an increased water flux. On the other hand, the enhancement of water flux was less significant when TiO₂ particles were incorporated into a loose PA film that was prepared with additives. In addition, a BSA fouling test confirmed that TiO₂ nanoparticles effectively improve the antifouling properties of the membranes for both dense and loose PA films. This effect is possibly due to increased hydrophilicity, covering of the fouling space, and a reduction in surface roughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43383.     

Studies on the surface properties of mixed‐matrix membrane and its antifouling properties for humic acid removal

A major factor limiting the use of ultrafiltration (UF) membrane in water treatment process is the membrane fouling by natural organic matter such as humic acid (HA). In this work, neat PVDF and PVDF/TiO₂ mixed‐matrix membranes were prepared and compared in terms of their antifouling properties. Two commercial types of TiO₂ namely PC‐20 and P25 were embedded to prepare the mixed matrix membranes via in situ colloidal precipitation method. The contact angles for the mixed‐matrix membranes were slightly reduced while the zeta potential was increased (more negatively charged) compared with the neat membrane. Filtration of HA with the presence of Ca²⁺ demonstrated that mixed‐matrix membrane could significantly mitigate the fouling tendency compared with the neat membrane with flux ratio (J/J₀) of 0.65, 0.70, and 0.82 for neat PVDF membrane, PVDF/TiO₂ mixed‐matrix membrane embedded with P25 and PC‐20, respectively. PC‐20 with higher anatase polymorphs exhibited better antifouling properties due to its hydrophilicity nature. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structural and performance properties of UV-assisted TiO2 deposited nano-composite PVDF/SPES membranes

In this research, the surface of poly (vinylidene fluoride) (PVDF)/sulfonated polyethersulfone (SPES) blend membrane prepared via immersion precipitation was modified by depositing of TiO₂ nano-particles followed by UV irradiation to activate their photocatalytic property. The membranes were characterized by FTIR, SEM, AFM, contact angle, dead end filtration (pure water flux and BSA solution flux), antifouling analysis and antibacterial activity. The FTIR spectrum confirmed the presence of OH functional groups on the PVDF/SPES membrane structure, which was the key factor for deposition, and self-assembly of TiO₂ nanoparticles on the membrane surface. The SEM and AFM images indicated that the TiO₂ nanoparticles were deposited on the PVDF/SPES membrane. The contact angle measurements showed that the hydrophilicity of PVDF/SPES membrane was strongly improved by TiO₂ deposition and UV irradiation. The filtration results indicated that the initial flux of TiO₂ deposited PVDF/SPES membranes was lower than the initial flux of neat PVDF/SPES membrane. However, the former membranes showed lower flux decline compared to the neat PVDF/SPES membrane. The BSA rejection of modified membranes was improved. The fouling analysis demonstrated that the TiO₂ deposited PVDF/SPES membranes showed the fewer tendencies to fouling. The results of antibacterial study showed that the UV irradiated TiO₂ deposited PVDF/SPES membranes possess high antibacterial property.     

Enhanced water flux through ultrafiltration polysulfone membrane via addition‐removal of silica nano‐particles: Synthesis and characterization

In the present paper, hierarchically structured ultrafiltration polysulfone (PSf) membrane was prepared to explore the effect of addition and subsequent removal of SiO₂ nano‐particles on the membrane morphology, hydrophilicity, and separation properties. The PSf based membranes namely PSf, PSf/SiO₂ and PSf/WSiO₂ (i.e. SiO₂ nano‐particles was acid‐washed and removed from PSf/SiO₂), were synthesized and characterized by different characterization methods. Pure water flux through the membranes was determined using a filtration unit operating at a continuous dead‐end flow mode. The modification enhanced the morphology, hydrophobicity, porosity and transport properties of the modified membranes, although the molecular weight cut‐off (MWCO) of the membranes was not changed considerably. In comparison, PSf/WSiO₂ membrane exhibited excellent pure water flux (about 4.5 times the flux of PSf, and 17 times the flux of PSf/SiO₂), although antifouling property of PSf/SiO₂ in separation of bovine serum albumin (BSA) was better than that of PSf and PSf/WSiO₂ membranes. The results suggested that the addition/removal of sacrificial solid fillers within/from a membrane matrix may provide a promising strategy to enhance PSf membrane transport property. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43556.     

Enhancing antifouling performance of poly(l‐lactide) membranes by TiO2 nanoparticles

Poly(l ‐lactide) (PLLA)/TiO₂ composite membranes were fabricated by immersion precipitation method. The resulting membranes were characterized using various methods including XRD, ATR‐FTIR, TGA, DSC, SEM, goniometer, and molecular weight cut‐off. The antifouling performance of the membrane was investigated through the filtration experiments of the oil/water emulsion. XRD, SEM, and ATR‐FTIR results indicated that TiO₂ was successfully introduced into the membrane, while DSC and TGA indicated the enhancement of thermal stability of membrane. The improvement of membrane hydrophilicity was confirmed by goniometer. In addition, the pore size and porosity on the membrane surface varied obviously with increasing the TiO₂ loading. It was concluded that PLLA/TiO₂ composite membranes had better antifouling and recycling performance compared with the pure PLLA membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43542.     

Application of Colloidal Precipitation Method Using Sodium Polymethacrylate as Dispersant for TiO2/PVDF Membrane Preparation and Its Antifouling Properties

Immobilized titanium dioxide (TiO₂) nanoparticles on flat sheet polymeric membranes have been found effective for fouling reduction in recent researches. The main challenge in this field is to obtain ultrafine and stable nanodispersions. In this study, composite polyvinylidene fluoride/TiO₂ (PVDF/TiO₂) ultrafiltration membranes were prepared via phase inversion and colloidal precipitation method. Stable TiO₂ suspensions were prepared using sodium polymethacrylate as dispersant and sonication without altering of the coagulation bath pH. The effect of different concentrations of TiO₂ nanoparticles in the coagulation bath was also investigated. The membrane morphology (distribution of nanoparticles on the membrane surface) was observed by scanning electron and atomic force microscopy. Properties of the neat and the composite membranes were also characterized using energy dispersive X‐ray spectroscopy and contact angle and membrane porosity measurements. The neat and the composite membranes were further investigated in terms of bovine serum albumin rejection and flux decline in cross flow filtration experiments. The results showed that the PVDF/TiO₂ composite membrane using dimethylacetamide/triethyl phosphate as solvent and 0.05 g/L of TiO₂ in the coagulation bath exhibits improved antifouling properties. POLYM. ENG. SCI., 59:E422–E434, 2019. © 2018 Society of Plastics Engineers     

Morphologies and properties of poly(phthalazinone ether sulfone ketone) matrix ultrafiltration membranes with entrapped TiO2 nanoparticles

Poly(phthalazine ether sulfone ketone) (PPESK) is a newly developed membrane material with superior thermal stability and comprehensive properties. Titanium dioxide (TiO₂)‐entrapped PPESK ultrafiltration (UF) membranes were formed by dispersing uniformly nanosized TiO₂ particles in the casting solutions. Initially, the inorganic nanoparticles were organically modified with silane couple reagent to overcome the aggregation and to improve the dispersibility in organic solvent. The membranes were prepared through the traditional phase inversion method. The effects of inorganic TiO₂ nanoparticles on the membrane surface morphology and cross section structure were investigated using scanning electronic microscopy (SEM) and atomic force microscopy (AFM). Water contact angle (CA) measurement was conducted to investigate the hydrophilicity and surface wettability of the membranes. The influence of TiO₂ on the permeability, antifouling, and tensile mechanical properties of the PPESK membranes were evaluated by UF experiments and tensile tests. The experimental results showed that the obtained TiO₂‐entrapped PPESK UF membranes exhibit remarkable improvement in the antifouling and mechanical properties because of the introduction of TiO₂ nanoparticles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3623–3629, 2007     

Asymmetric membranes fabricated from poly(acrylonitrile‐co‐N‐vinyl‐2‐pyrrolidone)s with excellent biocompatibility

Poly(acrylonitrile‐co‐N ‐vinyl‐2‐pyrrolidone)s (PANCNVPs) show excellent biocompatibility. In this work, PANCNVPs with different contents of N‐vinyl‐2‐pyrrolidone (NVP) were fabricated into asymmetric membranes by the phase inversion method. The surface chemical composition of the resultant membranes was determined by Fourier transform infrared spectroscopy–attenuated total reflection. Field emission scanning electron microscopy was used to examine the surface and cross section morphologies of the membranes. It was found that the morphologies hardly change with the increase of NVP content in PANCNVP, while the deionized water flux increases remarkably and the bovine serum albumin (BSA) retention decreases slightly. Experiment of dynamic BSA solution filtration was carried out to evaluate the antifouling properties of the studied membranes. The relative flux reduction of PANCNVP membrane containing 30.9 wt % of NVP is 25.9%, which is far smaller than that of the polyacrylonitrile membrane (68.8%). Results deduce that this improvement comes from the excellent biocompatibility of NVP moieties instead of the hydrophilicity change, because the water contact angles of these membranes fluctuate between 60 and 70°. Results from the membranes using poly(N‐vinyl‐2‐pyrrolidone) (PVP) as an additive confirm that, to a certain extent, the PANCNVP membranes show the advantages of antifouling compared with the polyacrylonitrile/PVP blending membrane. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4577–4583, 2006     

Antifouling ultrafiltration membrane fabricated from poly (arylene ether ketone) bearing hydrophilic hydroxyl groups

A new kind of membrane formation polymer, cardo poly(arylene ether ketone) bearing hydrophilic hydroxyl groups (PEK‐OH) was synthesized from the biphenol monomer 2‐(2‐hydroxyethyl)‐3, 3‐bis (4‐hydroxyphenyl)‐isoindolin‐1‐one (PPH‐OH), and 4, 4′‐difluorodiphenylketone. PEK‐OH asymmetric ultrafiltration membranes were prepared using the immersion coagulation phase inversion method. The PEK‐OH membrane prepared using the optimized conditions exhibited a pure water flux of 516 ± 18 L·m^?2·h^?1 and a 99.1 ± 1.4% rejection of bovine serum albumin (BSA) at an operating pressure of 0.1 MPa. The contact angle of PEK‐OH membrane was 66.0 ± 2.4 lower than these of the PEK‐C membrane (87.0 ± 2.8°, prepared from polymer PEK‐C under the same membrane formation condition as PEK‐OH membrane) and the UE50 membrane (84.0 ± 1.6°, a commercial PES ultrafiltration membrane). The amount of BSA protein adsorbed to the PEK‐OH membrane under static condition was measured to be 3.12 μg·cm^?2, which was greatly lower than that of 88.71 μg·cm^?2 and 74.40 μg·cm^?2 for the PEK‐C and the UE50 ultrafiltration membranes, respectively. Under dynamic filtration of BSA experiments, the PEK‐OH ultrafiltration membrane showed a 78.3% water flux recovery ratio, while only a 39.7% for the PEK‐C membrane and 46.5% for UE50 membrane were detected in the first cycle. After three cycles of BSA and LYZ filtration, the flux recovery ratio of PEK‐OH ultrafiltration membrane changed to be stable at 75% and 73%, while that of PEK‐C and UE50 ultrafiltration membranes remained declining gradually. Thus, hydrophilic PEK‐OH improves antifouling membrane property. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42809.     

Fabrication of an antifouling GO-TiO2/PES ultrafiltration membrane

PES ultrafiltration membrane is widely used in various fields due to its high-filtration efficiency. However, due to its hydrophobicity, PES ultrafiltration membrane has poor antifouling performance, this reduced service life and increased industrial cost. Blending is a common method in ultrafiltration membrane hydrophilic modification. Adding a small amount of inorganic nanoparticles into the polymer membrane can improve the properties of the polymer membrane. However, nanoparticles are not uniformly dispersed in polymer membrane, which hindering the modification ability of nanoparticles to ultrafiltration membrane. In this paper, GO-TiO₂ materials were prepared by hydrothermal method, and GO-TiO₂/PES blended ultrafiltration membranes were fabricated by nonsolvent induced phase separation (NIPs). The experimental results show that GO-TiO₂ disperse uniformly in GO-TiO₂/PES ultrafiltration membrane, which greatly improved the antifouling performance of the membrane. When the addition amount of GO-TiO₂ is 0.6%, the water flux of membrane reaches 194.5 (L m⁻² h⁻¹), and the rejection rate of BSA reaches 89.4%. After three pollutions-cycles, the flux recovery rate of the membrane is 90.2%.     

Preparation and characterization of antifouling poly(vinylidene fluoride) blended membranes

Poly(vinylidene fluoride) (PVDF) membranes have been widely used in microfiltration and ultrafiltration because of their excellent chemical resistance and thermal properties. However, PVDF membranes have exhibited severe membrane fouling because of their hydrophobic properties. In this study, we investigated the antifouling properties of PVDF blended membranes. Antifouling PVDF blended membranes were prepared with a PVDF‐g‐poly(ethylene glycol) methyl ether methacrylate (POEM) graft copolymer. The PVDF‐g‐POEM graft copolymer was synthesized by the atom transfer radical polymerization (ATRP) method. The chemical structure and properties of the synthesized PVDF‐g‐POEM graft copolymer were determined by NMR, Fourier transform infrared spectroscopy, and gel permeation chromatography. To investigate the antifouling properties of the membranes, we prepared microfiltration membranes by using the phase‐inversion method, which uses various PVDF/PVDF‐g‐POEM concentrations in dope solutions. The pure water permeabilities were obtained at various pressures. The PVDF/PVDF‐g‐POEM blended membranes exhibited no irreversible fouling in the dead‐end filtration of foulants, including bovine serum albumin, sodium alginate, and Escherichia coli broth. However, the hydrophobic PVDF membrane exhibited severe fouling in comparison with the PVDF/PVDF‐g‐POEM blended membranes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fabrication of a low‐cost nano‐SiO2/PVC composite ultrafiltration membrane and its antifouling performance

A novel low‐cost SiO₂/Polyvinylchloride (PVC) membrane with different nano‐SiO₂ particles loading (0–4 wt %) was prepared by the phase‐inversion process. The optimum nano‐SiO₂ dosage was determined as 1.5 wt % based on the casting solution compositions, the membranes' mechanical properties and hydrophilicities, the pure water fluxes, microstructures, and absorption of protein. Compared with the bare membrane, the membrane with 1.5 wt % nano‐SiO₂ addition presented better capabilities against the protein absorption and bacterial attachment, better antifouling performance, and higher flux recovery ratio in filtration of the supernatant liquor which collected from a secondary sedimentation tank in a municipal wastewater plant. The SiO₂/PVC membranes have applicable potential in the municipal wastewater treatment for their low price, good antifouling performance and high removal efficiencies of SS (over 97.2%), COD (up to 82.9%) and total bacteria (more than 93.6%). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41267.     

PEG/GO/TiO2纳米复合材料改性PVDF膜的制备及其抗污性能

为改善聚偏氟乙烯(PVDF)膜的抗污性能,以聚乙二醇2000接枝的GO/TiO₂(PEG/GO/TiO₂)纳米复合材料为添加剂,通过非溶剂诱导沉淀相分离法制备了一系列PEG/GO/TiO₂/PVDF复合超滤膜。采用FTIR、SEM和接触角测试仪对其结构和形貌进行了表征,采用超滤法评价其纯水通量和抗污性能。结果表明,当PEG/GO/TiO₂纳米复合材料质量分数为0.60%时,制备的PEG/GO/TiO₂/PVDF复合超滤膜(记为0.60%PEG/GO/TiO₂/PVDF)表现出最佳的亲水性和抗污性能,其接触角比PVDF膜下降8.2°,总孔隙率增加13.40%,PEG/GO/TiO₂纳米复合材料在PVDF膜中分散较均匀。在0.08 MPa的工作压力下,0.60%PEG/GO/TiO₂/PVDF的纯水通量高达282.44 L/(m²·h),对腐植酸溶液的过滤通量为131.96 L/(m^2...     

Sulfonated polyphenylsulfone asymmetric membranes: Effect of coagulation bath (acetic acid‐NaHCO3/isopropanol) on morphology and antifouling properties

Sulfonated polyphenylsulfone porous asymmetric membranes, S‐PPSU with different sulfonation degrees, 21, 33, 50 wt %, were prepared by phase inversion. Two different coagulation baths were explored for asymmetric membrane preparation: acetone/isopropanol and acetic acid (AA)‐NaHCO₃/isopropanol. The latter bath allows better morphology control for the nucleation and pore formation of the membrane. Scanning electron microscopy of membranes shows that pore interconnectivity is improved, when the mixture of AA‐NaHCO₃/isopropanol was used for asymmetric S‐PPSU ultrafiltration membranes preparation. S‐PPSU asymmetric membranes show an increasing hydrophilicity with increasing sulfonation degree. Asymmetric membrane antifouling properties improve as the concentration of sulfonic groups increases in the membrane showing twice the flux recovery ratio and lower BSA protein absorption in static and dynamic flux tests. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44502.     

Biofouling alleviation and flux enhancement of electrospun PAN microfiltration membranes by embedding of para‐aminobenzoate alumoxane nanoparticles

Membrane bioreactor (MBR) as a hybrid technology for wastewater treatment is becoming more popular for wastewater treatment. However, membrane fouling has hindered the widespread application of MBRs. Many efforts have been done for fouling mitigation. In this study, high flux and antifouling microfiltration membranes with unique surface structure, high surface porosity, and permeability were prepared by electrospinning technique. Initially, the optimum thickness of electrospun polyacrylonitrile (PAN) membranes was determined and then, electrospun PAN membrane at optimum thickness were prepared by embedding para‐aminobenzoate alumoxane (PABA) nanoparticles at different concentrations. The effect of PABA nanoparticles on membrane performance was investigated. To investigate the characterization of the prepared membranes Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive X‐ray spectroscopy, and water contact angle measurement were employed. The flux recovery ratio results revealed that the antifouling properties of the electrospun PAN membrane were enhanced by modification. The 3 wt % electrospun PABA embedded PAN had the best permeability, hydrophilicity, and antifouling properties among the fabricated membranes and showed remarkable reusability during filtration. The results obtained suggested that the high flux and antifouling electrospun PAN membranes embedded PABA nanoparticles could be used as MBR membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45738.     

Nano SiO2 and TiO2 embedded polyacrylonitrile/polyvinylidene fluoride ultrafiltration membranes: Improvement in flux and antifouling properties

Polyvinylidene fluoride (PVDF) and polyacrylonitrile (PAN) ultrafiltration (UF) membranes are widely used in drinking water and wastewater applications. These membranes are prone to fouling and membrane efficiency decreases with time under constant operation. Significant improvements/modifications are necessary to apply these polymers as sustainable membrane materials. In this study, PVDF and PAN UF membranes were modified through incorporation of nanoparticles (NPs) namely SiO₂ and TiO₂. PVDF and PAN UF membranes were prepared by phase inversion method from polymer solutions having dispersed SiO₂ and TiO₂ NPs in it. Membrane surface hydrophilicity, charge, roughness, and morphology were studied. Equilibrium water content and molecular weight cut-off of the membranes were also measured. Addition of NPs increased membrane surface hydrophilicity, equilibrium water content, and surface potential. NPs modified membranes exhibited better membrane flux (35–79% higher) and antifouling properties (flux recovery ratio values 28–41% higher) than the virgin membranes.     

Cellulose acetate ultrafiltration membranes customized with copper oxide nanoparticles for efficient separation with antifouling behavior

Cellulose acetate (CA) nanocomposite ultrafiltration membranes are fabricated with copper oxide (CuO) nanoparticles with the aim of improving efficient protein separation and antifouling performance. CuO nanoparticles are synthesized from cupric nitrate using a wet precipitation method and characterized by FTIR and XRD. CA/CuO nanocomposite membranes fabricated using 0.5, 1.0, and 1.5 wt% of CuO nanoparticles individually by simple phase inversion technique. The CA nanocomposite membrane with 0.5 wt% of hydrophilic CuO exhibited enhanced PWF of 118.6 Lm⁻² h⁻¹ due to the improvement in porosity and water uptake. This is in good agreement with the enhanced hydrophilicity of the CA/CuO nanocomposite membranes results observed in surface contact angle and morphological investigations. Further, 95.5% of BSA separation and 94.7% of flux recovery ratio (FRR) indicates its superior antifouling potential caused due to the presence of the hydration layer at the CA/CuO membrane surface. Among all the fabricated membranes, the CA-0.5 nanocomposite membrane with 0.5 wt% of CuO exhibited superiorly improved hydrophilicity, water permeation, BSA separation, and antifouling performance indicates its potential use in water and wastewater treatment applications.     

Enhanced water flux through graphitic carbon nitride nanosheets membrane by incorporating polyacrylic acid

Membranes assembled from two‐dimensional (2‐D) layered materials have shown potential use in water purification. Recently, a 2‐D graphitic carbon nitride (g‐C₃N₄) nanosheets membrane exhibits considerable separation performance in water purification. In this study, to further improve this water separation performance, polyacrylic acid (PAA) was introduced to tune the nanochannels formed between the g‐C₃N₄ nanosheets. The fabricated g‐C₃N₄‐PAA hybrid membranes possessed higher water flux without sacrificing much rejection rate compared with that of the g‐C₃N₄ membrane; however, noticeable fouling was observed upon addition of the PAA into the membrane composite structure. In addition, the effect of PAA on the morphology, surface hydrophilicity, separation performance, and antifouling properties of the g‐C₃N₄ membrane were examined in detail. Overall, incorporating PAA into the g‐C₃N₄ nanosheets membrane was an effective and convenient method to improve the water separation performance, which could promote the application of the 2‐D g‐C₃N₄ nanosheets membrane in practical ultrafiltration processes. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2181–2188, 2018